Nanocontacts: probing electronic structure under extreme uniaxial strains

Nanometer-sized metallic necks have the unique ability to sustain extreme uniaxial loads (about 20 times greater than the bulk material). We present an experimental and theoretical study of the electronic transport properties under such extreme conditions. Conductance measurements on gold and aluminum necks show a strikingly different behavior: While gold shows the expected conductance decrease with increasing elastic elongation of the neck, aluminum necks behave in the opposite way. We have performed first-principles electronic-structure calculations which reproduce this behavior, showing that it is an intrinsic property of the bulk band structure under high uniaxial strain.

Análise numérico-experimental de blindagens balísticas

O desenvolvimento técnico e científico em torno das blindagens tem procurado contrariar o constante aperfeiçoamento dos projéteis e do seu poder de penetração. Para cumprir este objetivo, é necessário recorrer a soluções inovadoras tanto em termos dos materiais utilizados no fabrico, como ao nível do formato da própria blindagem. Com este trabalho pretende-se dar os primeiros passos na produção e teste de materiais em situação de tiro real, bem como na modelação e simulação dos mesmos com o objetivo de adquirir capacidades, técnicas e procedimentos para trabalhos futuros. O trabalho teve início com a realização da pesquisa bibliográfica sobre vários aspetos desde o fabrico até à avaliação do desempenho de blindagens balísticas. O trabalho teórico desta tese incidiu na modelação por elementos finitos dos elementos balísticos (proteções e projétil) tendo como objetivo a simulação numérica da sua interação em condições de impacto. O trabalho experimental foi realizado no campo de tiro da Escola das Armas onde foram testados os alvos com os materiais compósitos produzidos e com placas de alumínio, com diferentes combinações. A análise de resultados permitiu comparar e avaliar as diferenças entre as estimativas teóricas e as suas limitações com as observações experimentais do tiro real.

Materials shortages : hearings before the Permanent Subcommittee on Investigations of the Committee on Government Operations, United States Senate, Ninety-third Congress, second session, pursuant to section 4, Senate resolution 269, 93d Congress.

Hearings held Sept. 11-Dec. 17, 1974.

40Ar/39Ar geochronological constraints on the evolution of lateritic iron deposits in the Quadrilatero Ferrifero, Minas Gerais, Brazil

Weathering profiles overlying the Sapecado, Pico and Andaime iron ore deposits, Quadrilátero Ferrífero (QF), Minas Gerais, Brazil, reach depths of 150–400 m and host world-class supergene iron orebodies. In addition to hosting supergene ore bodies of global economic significance, weathered banded iron-formations at the Quadrilátero Ferrífero and elsewhere (e.g., Carajás, Hamersley) are postulated to underlie some of the most ancient continuously exposed weathering profiles on earth. Laser incremental-heating 40Ar/39Ar results for 69 grains of hollandite-group manganese oxides extracted from 23 samples collected at depths ranging from 5 to 150 m at the Sapecado, Pico and Andaime deposits reveal ages ranging from ca. 62 to 14 Ma. Older Mn-oxides occur near the surface, while younger Mn-oxides occur at depth. However, many samples collected at the weathering–bedrock interface yield ages in the 51–41 Ma range, suggesting that the weathering profiles in the Quadrilátero Ferrífero had already reached their present depth in the Paleogene. The antiquity of the weathering profiles in the Quadrilátero Ferrífero is comparable to the antiquity of dated weathering profiles on banded iron-formations in the Carajás Region (Brazil) and the Hamersley Province, Western Australia. The age versus depth distributions obtained in this study, but not available for other regions containing similar supergene iron deposits, suggest that little further advance of the weathering front has occurred in the Quadrilátero Ferrífero lateritic profiles during the Neogene. The results suggest that weathering in some of these ancient landscapes is not controlled by the steady-state advance of weathering fronts through time, but may reflect climatic and geomorphological conditions prevailing in a remote past. The geochronological results also confirm that the ancient landsurfaces in the Quadrilátero Ferrífero probably remained immune to erosion for tens of millions of years. Deep weathering, mostly in the Paleogene, combined with low erosion rates, account for the abundance and widespread distribution of supergene iron, manganese, and aluminum orebodies in this region.

Thin films fabricated from a nanoparticle beam

As time advances, man has been able to control technology in finer and finer detail. The microelectronics era is an example of this, with control down to the micrometer. Experts agree that we may be entering a new era, controlling technology down to the nanometer. One aspect of such control is making materials in the nanometer range, i.e. nanoparticles. For this purpose, a new magnetron-sputtering gun, inert gas condensation, nanoparticle source has been designed, built, and tested. ^ Films made from cobalt, nickel, tantalum, molybdenum, chromium, and aluminum have been investigated. Transmission Electron Microscope measurements done at the University of Illinois confirm the thin films are nanostructured. This was also confirmed by Atomic Force Microscope measurements made at the F.I.U. Thin Film Laboratory. ^ Composition, optical and magnetic properties have been measured. In most cases, unique properties have been found that differ significantly from bulk properties. Rutherford Backscattering measurements done at the University of Illinois determined significant percentages of oxygen and carbon in the samples, possibly due to interactions with air. Because of this, optical properties are a composite of oxide, metal, and void properties. Magnetic materials were determined to have spin-glass properties below the irreversibility temperature and superparamagnetic properties above it. Indications of possible future uses for these nanostructured materials are discussed. ^

Caracterização de água de lavagem de filtros em estações de tratamento de água de filtração direta

The water supply and treatment is considered as a great benefit considering that, if done efficiently, provides public health. However, considering the WTP (Water Treatment Plant) is an industry, with its inputs and waste generation, they must be constantly evaluated and monitored to verify the best and most appropriate way to process and dispose their waste, minimizing therefore the potential impacts to the environment. By volume, the most significant waste is the rapid filter backwash water. It is very common the disposal of this waste without treatment in water sources, which are used, for the most part, as a water supply source of a downstream population. This study evaluated quantitative and qualitative parameters in filter backwash water in three WTP - Itaitinga, Maranguape and Pacatuba, located in Ceará State, northeast of Brazil. It was found that the Maranguape WTP, in terms of treatment capacity, is the larger. The Itaitinga WTP is the one that consumes more water during filters washing. The Pacatuba WTP exhibited higher concentration of total suspended and settleable solids, COD and aluminum in the filters backwash water. It is noteworthy that the settleable solids and total suspended solids in all three WTP are above the effluent discharge standard recommended by Resolution 154/2002 of SEMACE (State Superintendent of Environment of Ceará). It was concluded that the filter backwash water from the study WTP exceeded the allowed values for legislation to be disposed directly into surface water bodies. It is suggested as an alternative to treat and recycle the filter backwashing water the construction of sludge settling ponds.

Alquilação de tolueno com propeno, através de complexo ferro (II) ᵦ- diimina homogêneo e heterogeneizado em MCM-41, Al-MCM-41 e SBA-15

This work describes the synthesis and aplication of homogeneous and heterogenized iron catalysts in the alkylation reaction of toluene with propene, empolying experimental design. The homogenous complex was obtained trough the synthesis of the organic ligand folowed by the complexation of the iron(II) chloride. As to the heterogenized complexes, first were synthetized the inorganic supports (SBA-15, MCM-41 and Al-MCM-41). Then, it was synthetized the ligand again, that through funcionalization with chloropropyltrimethoxysilane (CPTMS), was anchored on the support previously calcinated. To these anchored ligands, was complexed the iron(II) chloride, previously solubilizated in tetrahydrofuran (THF). The organic ligand characterization was accomplished trough nuclear magnetic resonance (NMR) and Infrared spectroscopy (IV). The supports were characterized with x-ray diffraction (DRX), texture analysis with nitrogen adsorption/desorption (before and after the anchoring), termogravimetric analysis (TG) and infrared (IV). The metalic content was quantified trough the atomic absorption spectrophotometry (AAS). The complexes were tested in catalytic reactions emolying ethylaluminium sesquichloride (EASC) as co-catalyst in steel reactor, under mecanic stirring. The reaction conditions ranged from 4 to 36 ◦C, with many aluminum/iron ratios. The catalysts were actives in homogeneous and heterogenized ways. The homogenous catalytic complex showed a maximum turnover frequency (TOF) of 8.63 ×103 · h −1 , while, in some conditions, the anchored complexes showed better results, with TOF of until 8.08 ×103 · h −1 . Aditionally, it was possible to determine an equation, to the homogenous catalyst, that describes the product quantity in function of reacional temperature and aluminum/iron ratio.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Biogeochemical properties of sinking particles intercepted at three depths on the NW Atlantic margin

Three conical sediment were deployed at three depths 968 m (top trap), 1976 m (middletrap), and 2938 m (50mabove the bottom, bottom trap) - from June 27, 2004 to April 27, 2005 on the NW Atlantic margin at a water depth of 2988 m. The sediment trap carousels were programmed to open each collection cup for 23.4 days for the top trap and 14.5 days for the other two traps, resulting in total 13 samples from the top trap and 21 samples each from the middle and bottom traps. The samples were analyzed for the biogeochemical properties with various methods. Frequent occurrences of higher fluxes in deep relative to shallower sediment traps and low delta 14C values of sinking POC together provide strong evidence for significant lateral transport of aged organic matter over the margin. Comparison of biogeochemical properties such as aluminum concentration and flux, and iron concentration between samples intercepted at different depths shows that particles collected by the deepest trap had more complex sources than the shallower ones. These data also suggest that at least two modes of lateral transport exist over the New England margin. Based on radio carbon mass balance, about 30% (± 10%) of sinking POC in all sediment traps is estimated to be derived from lateral transport of re-suspended sediment. A strong correlation between delta 14C values and aluminum concentrations suggests that the aged organic matter is associated with lithogenic particles.

New pairing scheme to overhaul BCS theory

In a superconductor pair occupancy probabilities are doubly defined with conflicting values when normal and umklapp scattering coexist with the same destination momentum. To resolve this issue a new pairing scheme is introduced to assert normal–umklapp frustration under such circumstances. Superconductivity then arises solely from residual umklapp scattering to destination momenta not reached by normal scattering. Consequent Tc calculations from first principles for niobium, tantalum, lead and aluminum turn out to be accurate within a few percent. A new perspective is revealed to support Matthias׳ rule. New light is also shed relevant to the future study of metallic hydrogen.

Caractérisation des propriétés mécaniques de la pâte de carbone à 150°C dans le but d’optimiser la mise en forme des anodes utilisées dans les cuves Hall-Héroult

Les anodes de carbone sont des éléments consommables servant d’électrode dans la réaction électrochimique d’une cuve Hall-Héroult. Ces dernières sont produites massivement via une chaine de production dont la mise en forme est une des étapes critiques puisqu’elle définit une partie de leur qualité. Le procédé de mise en forme actuel n’est pas pleinement optimisé. Des gradients de densité importants à l’intérieur des anodes diminuent leur performance dans les cuves d’électrolyse. Encore aujourd’hui, les anodes de carbone sont produites avec comme seuls critères de qualité leur densité globale et leurs propriétés mécaniques finales. La manufacture d’anodes est optimisée de façon empirique directement sur la chaine de production. Cependant, la qualité d’une anode se résume en une conductivité électrique uniforme afin de minimiser les concentrations de courant qui ont plusieurs effets néfastes sur leur performance et sur les coûts de production d’aluminium. Cette thèse est basée sur l’hypothèse que la conductivité électrique de l’anode n’est influencée que par sa densité considérant une composition chimique uniforme. L’objectif est de caractériser les paramètres d’un modèle afin de nourrir une loi constitutive qui permettra de modéliser la mise en forme des blocs anodiques. L’utilisation de la modélisation numérique permet d’analyser le comportement de la pâte lors de sa mise en forme. Ainsi, il devient possible de prédire les gradients de densité à l’intérieur des anodes et d’optimiser les paramètres de mise en forme pour en améliorer leur qualité. Le modèle sélectionné est basé sur les propriétés mécaniques et tribologiques réelles de la pâte. La thèse débute avec une étude comportementale qui a pour objectif d’améliorer la compréhension des comportements constitutifs de la pâte observés lors d’essais de pressage préliminaires. Cette étude est basée sur des essais de pressage de pâte de carbone chaude produite dans un moule rigide et sur des essais de pressage d’agrégats secs à l’intérieur du même moule instrumenté d’un piézoélectrique permettant d’enregistrer les émissions acoustiques. Cette analyse a précédé la caractérisation des propriétés de la pâte afin de mieux interpréter son comportement mécanique étant donné la nature complexe de ce matériau carboné dont les propriétés mécaniques sont évolutives en fonction de la masse volumique. Un premier montage expérimental a été spécifiquement développé afin de caractériser le module de Young et le coefficient de Poisson de la pâte. Ce même montage a également servi dans la caractérisation de la viscosité (comportement temporel) de la pâte. Il n’existe aucun essai adapté pour caractériser ces propriétés pour ce type de matériau chauffé à 150°C. Un moule à paroi déformable instrumenté de jauges de déformation a été utilisé pour réaliser les essais. Un second montage a été développé pour caractériser les coefficients de friction statique et cinétique de la pâte aussi chauffée à 150°C. Le modèle a été exploité afin de caractériser les propriétés mécaniques de la pâte par identification inverse et pour simuler la mise en forme d’anodes de laboratoire. Les propriétés mécaniques de la pâte obtenues par la caractérisation expérimentale ont été comparées à celles obtenues par la méthode d’identification inverse. Les cartographies tirées des simulations ont également été comparées aux cartographies des anodes pressées en laboratoire. La tomodensitométrie a été utilisée pour produire ces dernières cartographies de densité. Les résultats des simulations confirment qu’il y a un potentiel majeur à l’utilisation de la modélisation numérique comme outil d’optimisation du procédé de mise en forme de la pâte de carbone. La modélisation numérique permet d’évaluer l’influence de chacun des paramètres de mise en forme sans interrompre la production et/ou d’implanter des changements coûteux dans la ligne de production. Cet outil permet donc d’explorer des avenues telles la modulation des paramètres fréquentiels, la modification de la distribution initiale de la pâte dans le moule, la possibilité de mouler l’anode inversée (upside down), etc. afin d’optimiser le processus de mise en forme et d’augmenter la qualité des anodes.

O metal na arquitetura contemporânea paraibana 1990-2002

This essay studies about contemporary architecture in João Pessoa, capital city of Paraiba State, which analyzes the utilization of steel and aluminum materials from 1990 to 2002, period when significant increase of this utilization is seen. As references, the architectural analysis and Engel structures definitions were used to analyze 40 built buildings, universe researched, to bring together subsidies to comprehend the contemporary production, especially which use the metal as structural and esthetic-formal element

Valoração do efluente da indústria processadora de pescado por incorporação de nutrientes em aphanothece microscopica nägeli

Nesta tese procurou-se demonstrar a valoração do efluente do processamento de pescado por incorporação dos nutrientes em Aphanothece microscopica Nägeli a diferentes temperaturas. Para tanto o trabalho é composto de cinco artigos que objetivaram avaliar sob o ponto de vista do tratamento do efluente pela cianobactéria Aphanothece e a separação e avaliação da biomassa gerada. O primeiro artigo intitula-se “Influência da temperatura na remoção de nutrientes do efluente da indústria de pescado por Aphanothece microscopica Nägeli”, e teve por objetivo avaliar a influência da temperatura (10, 20 e 30ºC) em um sistema de tratamento pela cianobactéria Aphanothece na remoção de matéria orgânica, nitrogênio e fósforo do efluente oriundo do processamento de pescado. A análise dos resultados mostrou que a temperatura influenciou significativamente na remoção de DQO, NTK, N-NH4 + e P-PO4 -3 . Para os experimentos a 20 e 30ºC todos os limites estabelecidos para os parâmetros avaliados foram atingidos. O segundo artigo intitulado “Efeito de coagulantes no efluente da indústria da pesca visando à separação de biomassa quando tratado por cianobactéria” avaliou o efeito da concentração e pH de dois tipos de coagulantes, cloreto férrico (FeCl3) e sulfato de alumínio (Al2(SO4)3), na separação da biomassa da cianobactéria Aphanothece microscopica Nägeli cultivada em efluente da indústria da pesca, assim como a remoção de matéria orgânica e nutrientes do efluente. Os resultados indicaram que o coagulante FeCl3 foi mais eficaz na remoção de todos os parâmetros testados. No que concerne à separação da biomassa, com um número de seis lavagens foi removido cerca de 97,6% da concentração de FeCl3 adicionado inicialmente. O terceiro artigo com o título “Caracterização da biomassa de Aphanothece microscopica Nägeli gerada no efluente da indústria da pesca em diferentes temperaturas de cultivo” avaliou a composição química da biomassa da cianobactéria Aphanothece microscopica Nägeli quando desenvolvida em meio de cultivo padrão BG11 e no efluente do processamento de pescado. O quarto artigo teve como título “Influência do meio de cultivo e temperatura em compostos nitrogenados na cianobactéria Aphanothece microscopica Nägeli” objetivou avaliar o teor de compostos nitrogenados presentes na biomassa da cianobactéria Aphanothece microscopica Nägeli quando cultivada em meio padrão e no efluente da indústria da pesca nas diferentes fases de crescimento. Para o estudo da composição química e nitrogenados no efluente foram realizados experimentos nas temperaturas de 10, 20 e 30ºC. As concentrações de proteína, cinzas e pigmentos aumentaram com o aumento da temperatura. Por outro lado, foi observada uma redução do teor de lipídios e carboidratos com o aumento da temperatura. O íon amônio juntamente com os ácidos nucléicos representa uma importante fração do nitrogênio não protéico presente na biomassa da cianobactéria Aphanothece. Ficou demonstrada a influência do meio de cultivo na concentração de nitrogênio, bem como a determinação de proteína pelo método de Kjeldahl superestima a concentração protéica em cianobactérias. O quinto artigo intitulado “Produção de proteína unicelular a partir do efluente do processamento do pescado: modelagem preditiva e simulação” avaliou a produção de proteína unicelular através do cultivo da cianobactéria Aphanothece microscopica Nägeli no efluente da indústria da pesca. Os dados cinéticos de crescimento celular foram ajustados a quatro modelos matemáticos (Logístico, Gompertz, Gompertz Modificado e Baranyi). Os resultados demonstraram que o modelo Logístico foi considerado o mais adequado para descrever a formação de biomassa. A análise preditiva mostrou a possibilidade da obtenção de 1,66, 18,96 e 57,36 kg.m-3.d-1 de biomassa por volume do reator em 1000 h de processo contínuo, para as temperaturas de 10, 20 e 30ºC, respectivamente.

Estudio in vitro de la resistencia adhesiva en la interfaz de resina entre la base del pad y el resinoso utilizado en cementación indirecta de la técnica lingual

Con el fin de aminorar retrasos por descementación de cualquier accesorio durante el tratamiento de Ortodoncia Lingual, se ha considerado que la fuerza de adhesión es muy importante, especialmente cuando está ubicada en las diferentes interfaces presentes entre el bracket y la resina del PAD; entre la resina del PAD y el cemento resinoso fotopolimerizable y entre este cemento y el esmalte dental. Por lo que este estudio se ha enfocado en determinar la resistencia adhesiva en la interfaz localizada entre la resina de la base del PAD y el cemento resinoso fotopolimerizable utilizando ácido fluorhídrico y óxido de aluminio como tratamiento de superficie previo a la cementación indirecta de la técnica lingual. MATERIALES Y METODOS: El tipo de estudio fue experimental "in vitro", con una muestra de 30 cuerpos de prueba hechos con resina Transbond XT, utilizando para su confección un blíster de brackets, se siguieron tres protocolos diferentes; G1 o grupo control sin ninguna preparación, G2 con aplicación de óxido de aluminio, 50 micrones durante 10 segundos en la superficie del cuerpo de prueba, G3 con aplicación de ácido fluorhídrico al 9% en la superficie del cuerpo de prueba durante 10 minutos. Previo al test de resistencia adhesiva, se realizó los cortes de precisión en cada cuerpo de prueba, obteniendo así 45 tiras de prueba, cada una de las muestras fue adherida a un porta muestra para la prueba de micro tracción, la misma que fue realizada con la máquina universal Mini-Instron modelo 5942, a una velocidad de deformación constante de 0.5 mm/min. Los datos fueron sometidos al test de Normalidad de residuos de Shapiro Wilk (p>0,05) y de LEVENE para el análisis de homogeneidad de las varianzas. La resistencia adhesiva fue comparada entre los grupos por medio del Análisis de Varianza (ANOVA) como factor único para el procesamiento de los datos. Para todos los análisis el nivel de significancia fue del 5% (p< 0,05) con un nivel de confianza del 95% (IC95%). Se consideró estadísticamente significativo valores por debajo de 0,05. RESULTADOS Y CONCLUSIONES: El resultado del test de ANOVA, reveló que el factor de tratamiento de superficie F(2,12)=2,52;p=0,12 no es significante, por lo tanto los diferentes tratamientos de superficie (óxido de aluminio y ácido fluorhídrico) utilizados son equivalentes al grupo control, indicando que no ejercen influencia de manera significativa en los valores de Resistencia Adhesiva (RA) en la preparación de la interfaz localizada entre la resina de la base del PAD y el cemento resinoso fotopolimerizable; concluyendo que se puede utilizar cualquier protocolo de tratamiento de superficie indicado en la presente investigación.