Extensive boiling as a precipitation mechanism for precious and base metal ores, Bienaventurada Mine, Huancavelica, Perú

The Bienaventurada mine operates a polymetallic Ag-Pb-Zn (Cu, Au) vein system of the low sulphidation epithermal type. Fluid inclusions, FI, are abundant in quartz, sphalerite and adularia. FI petrography demonstrates typical primary growth zoning which occurs frequently in crystalline quartz, and defines the most common primary FI. These are usually very small, but several types of primary, P, and secondary, S, FI Assemblages (FIAs) comprising FI of measurable size (3 to > 100 μm) can also be identified through careful petrographic work. The fluids are aqueous and undersaturated, and no evidence of CO2 was found; the degree of fill is usually high (~70-80 %) in the L-rich inclusions, but extremely low in V-rich inclusions. The measured microthermometric values are very consistent in the FIAs selected; they are for the most part roughly similar in the P and S assemblages: the median is typically ~258ºC for total homogenization temperatures, Th, and -1.5 ºC for ice melting temperatures, Tm (corresponding to 2.57 wt% NaCl eq). The widespread occurrence of L-rich and V-rich FI in the same FIA and the consistent Th values point to an extensive boiling system along the vein. In these conditions, Th equals T of trapping, and the ores are assumed to have been precipitated from an aqueous low salinity boiling fluid, of likely meteoric origin, at some 250-280º C, under ~500 m hydrostatic head.

The Islamic Crossed-Arch Domes in Cordoba: Geometry and Structural Analysis of the “Capilla de Villaviciosa”

Crossed-arch domes are a singular type of ribbed vaults. Their characteristic feature is that the ribs that form the vault are intertwined, forming polygons or stars, leaving an empty space in the centre. The earliest known vaults of this type are found in the Great Mosque of Córdoba, built ca. 960 a.C. The type spread through Spain, and the north of Africa in the 10th to the 16th Centuries, and was used by Guarini and Vittone in the 17th and 18th Centuries in Italy. However, it was used only in a few buildings. Though the literature about the structural behaviour of ribbed Gothic vaults is extensive, so far no structural analysis of crossed arch domes has been made. The purpose of this work is, first to show the way to attack such an analysis within the frame of Modern Limit Analysis of Masonry Structures (Heyman 1995), and then to apply the approach to study the stability of the dome of the Capilla de Villaviciosa. The work may give some clues to art and architectural historians to understand better the origin and development of Islamic dome architecture.

Historia holocena de los pinares montanos de los sistemas Central y Cantábrico: Un objetivo con dos enfoques, biogeográfico y dendroecológico

Los estudios paleoecológicos holocenos basados en macro- y megafósiles encierran un gran valor debido a que su información tiene generalmente carácter local, su origen es conocido, pueden ser datados directamente mediante el método radiocarbónico, y pueden identificarse a un nivel taxonómicamente preciso. Sin embargo son pocas las áreas del Sur de Europa en las que sea conocida una alta densidad de yacimientos con restos leñosos de gran tamaño. En esta tesis, se presentan datos de 53 yacimientos de la sierra de Gredos y de la cordillera Cantábrica (Península Ibérica). Los restos fueron hallados en ambientes variados, como zonas higroturbosas, turberas erosionadas o lagos, y fueron identificadas mediante el estudio de la anatomía de la madera o mediante rasgos morfológicos. En la sierra de Gredos, la evidencia paleobotánica indica la existencia de un panorama relativamente estable a lo largo del Holoceno medio y principio del Holoceno final y sugiere la persistencia, a lo largo de milenios, de un piso de pinares ampliamente distribuído en cotas altas de la sierra. La información obtenida de piñas y frutos mejoran la información taxonómica disponible y revelan la existencia tanto de Pinus sylvestris como de Pinus nigra en estas sierras durante el Holoceno. La datación radiocarbónica, medición de anillos de crecimiento y sincronización preliminar de 26 secciones de troncos de subfósiles demuestran el potencial de este material de las montañas de Iberia central en la obtención de cronologías holocenas de pino. En la cordillera Cantábrica, los datos aportan información espacialmente precisa de distribuciones de ciertas especies arbóreas durante el Holoceno. En las zonas centrales de la cordillera, han sido hallados fundamentalmente restos de pino, mientras que en las zonas más occidentales los pinos estás ausentes y los restos encontrados corresponden a otras especies de caducifolios (Betula, Salix, Quercus) y arbustos (Erica, Fabaceae) Esta información paleobiogeográfica constrasta con la distribución natural actual de Pinus sylvestris y Pinus nigra en el área de estudio. En la sierra de Gredos, la naturalidad de las escasos rodales de pinos que aún persisten ha sido discutida, mientras que en la cordillera Cantábrica, la única especie del grupo que persiste es P. sylvestris y está localizada en unos pocos relictos. El clima pudo haber jugado un papel importante en una primera fase de declive de los pinares durante el Holoceno inicial, mostrado en numerosos registros polínicos de manera casi sincrónica y asociada a una expansión de frondosas. Sin embargo la información histórica disponible y la comparación entre las áreas de distribución de los pinares en el presente, modelizada y en momentos anteriores a la la generalización de la presión antrópica sugiere que durante los últimos dos milenios, la actividad humana ha sido responsable de la desaparición de estas especies como árboles naturales en áreas extensas. ABSTRACTMacro- and megafossil studies provide information of great value in palaeoecology because such evidence is spatially precise, directly radiocarbon dated and usually taxon-specific. However, few areas of southern Europe have a high density of sites with Holocene woody remains. Here, local data from 53 sites in the Gredos Mountains and the Cantabrian Range (Iberian Peninsula) is presented. Woody remains were recovered from mires, eroded peat bogs and lakes and were identified by their wood anatomy or morphological traits. In the Gredos Mountains, palaeobotanical evidence portrays a relatively stable picture of tree distribution over the mid- and beggining of the late-Holocene, and suggests the persistence of a widespread belt of pinewoods. Cones and fruits enlarge the taxonomic information available and reveal that both Pinus sylvestris and Pinus nigra were present locally during the Holocene. Radiocarbon dating, tree ring measurement and preliminary cross-dating of 26 pine sub-fossil logs demonstrate the potential of obtaining a long pine chronology from subfossil wood from the mountains of Central Iberia. In the Cantabrian Range the data provide spatially precise evidence of tree distribution in the region during the Holocene. Pines were mostly identified in the central areas, whereas at the western edge no pine evidence was detected and deciduous trees (Betula, Salix, Quercus) and shrubs (Erica, Fabaceae) were identified. This palaeoecological information contrasts with the current natural distribution ranges of P. sylvestris and P. nigra in the study area. In the Gredos Mountains, the naturality of the few pine stands currently growing has been heavily debated. In the Cantabrian Range P. sylvestris is the only pine species that is today present, and its natural presence is now limited to a few enclaves. Climate may have played a key role in the early-Holocene, as pollen archives document a pine demise that is synchronous with the spread of broadleaved taxa. However, available historical data and the comparison of the reconstructed distribution of pinewoods before extensive human forest disturbance with both present and modelled distributions suggests that during the last two millennia, anthropogenic activity may have removed these species as native trees from a large territory.

Contribución a la automatización de sistemas de respuesta frente a intrusiones mediante ontologías

La seguridad en redes informáticas es un área que ha sido ampliamente estudiada y objeto de una extensa investigación en los últimos años. Debido al continuo incremento en la complejidad y sofisticación de los ataques informáticos, el aumento de su velocidad de difusión, y la lentitud de reacción frente a las intrusiones existente en la actualidad, se hace patente la necesidad de mecanismos de detección y respuesta a intrusiones, que detecten y además sean capaces de bloquear el ataque, y mitiguen su impacto en la medida de lo posible. Los Sistemas de Detección de Intrusiones o IDSs son tecnologías bastante maduras cuyo objetivo es detectar cualquier comportamiento malicioso que ocurra en las redes. Estos sistemas han evolucionado rápidamente en los últimos años convirtiéndose en herramientas muy maduras basadas en diferentes paradigmas, que mejoran su capacidad de detección y le otorgan un alto nivel de fiabilidad. Por otra parte, un Sistema de Respuesta a Intrusiones (IRS) es un componente de seguridad que puede estar presente en la arquitectura de una red informática, capaz de reaccionar frente a los incidentes detectados por un Sistema de Detección de Intrusiones (IDS). Por desgracia, esta tecnología no ha evolucionado al mismo ritmo que los IDSs, y la reacción contra los ataques detectados es lenta y básica, y los sistemas presentan problemas para ejecutar respuestas de forma automática. Esta tesis doctoral trata de hacer frente al problema existente en la reacción automática frente a intrusiones, mediante el uso de ontologías, lenguajes formales de especificación de comportamiento y razonadores semánticos como base de la arquitectura del sistema de un sistema de respuesta automática frente a intrusiones o AIRS. El objetivo de la aproximación es aprovechar las ventajas de las ontologías en entornos heterogéneos, además de su capacidad para especificar comportamiento sobre los objetos que representan los elementos del dominio modelado. Esta capacidad para especificar comportamiento será de gran utilidad para que el AIRS infiera la respuesta óptima frente a una intrusión en el menor tiempo posible. Abstract Security in networks is an area that has been widely studied and has been the focus of extensive research over the past few years. The number of security events is increasing, and they are each time more sophisticated, and quickly spread, and slow reaction against intrusions, there is a need for intrusion detection and response systems to dynamically adapt so as to better detect and respond to attacks in order to mitigate them or reduce their impact. Intrusion Detection Systems (IDSs) are mature technologies whose aim is detecting malicious behavior in the networks. These systems have quickly evolved and there are now very mature tools based on different paradigms (statistic anomaly-based, signature-based and hybrids) with a high level of reliability. On the other hand, Intrusion Response System (IRS) is a security technology able to react against the intrusions detected by IDS. Unfortunately, the state of the art in IRSs is not as mature as with IDSs. The reaction against intrusions is slow and simple, and these systems have difficulty detecting intrusions in real time and triggering automated responses. This dissertation is to address the existing problem in automated reactions against intrusions using ontologies, formal behaviour languages and semantic reasoners as the basis of the architecture of an automated intrusion response systems or AIRS. The aim is to take advantage of ontologies in heterogeneous environments, in addition to its ability to specify behavior of objects representing the elements of the modeling domain. This ability to specify behavior will be useful for the AIRS in the inference process of the optimum response against an intrusion, as quickly as possible.

Fundamentos constructivos de las fortificaciones fronterizas entre las coronas de Castilla y Aragón de los siglos XII al XV en la actual provincia de Soria

La tesis doctoral desarrolla una investigación original, dentro del marco disciplinario de la historia de la construcción, sobre los fundamentos constructivos de las fortificaciones bajomedievales fronterizas entre las Coronas de Castilla y Aragón en la actual provincia de Soria. En el título de la tesis ya queda expresado el objeto fundamental y fundacional, así como el ámbito temporal —desde la reconquista del oriente soriano por parte de Alfonso I el Batallador a principios del siglo XII hasta la unificación de las coronas hispánicas en el siglo XV bajo el común mandato de los Reyes Católicos— y la extensión territorial que delimita la investigación: aquéllas comarcas castellanas lindantes con Aragón pertenecientes a la actual provincia de Soria. Durante este período bajomedieval se produjeron una serie de enfrentamientos fronterizos que obligó a fortificar la frontera y las vías de comunicación entre ambas coronas. La falta de estudios de conjunto de estas fortificaciones entendiéndolas como participantes en un sistema fortificado ha constituido la justificación de la investigación, que se realiza en varios niveles de análisis: territorial, histórico, arquitectónico, poliorcético y constructivo. Así mismo, se ha detectado cierta falta de rigor acompañada de inexactitudes en las consideraciones constructivas publicadas sobre algunas de las fortificaciones del ámbito de estudio, lo que ha provocado errores en su datación al no más haber elementos de corte artístico o estilístico que marquen indudablemente la pertenencia a una época. En la tesis se ponen en duda las dataciones tradicionalmente aceptadas planteando la hipótesis que da pie a la investigación: ante la falta de elementos artísticos o estilísticos en unos sobrios edificios eminentemente funcionales es posible establecer con suficiente aproximación la fecha de construcción en base a criterios constructivos una vez formada una clasificación cronotipológica de cada técnica constructiva. La hipótesis, por lo tanto, plantea un objetivo principal —el estudio de la razón constructiva del sistema fortificado fronterizo— desarrollado en una serie de objetivos específicos cuya consecución programa los sucesivos niveles de análisis: - Conocer y detallar los elementos históricos que originaron los enfrentamientos entre las Coronas de Castilla y Aragón y su desarrollo mediante herramientas historiográficas y analizar las características naturales del territorio en litigio mediante instrumentos cartográficos. - Conocer y analizar los tipos arquitectónicos y las tradiciones constructivas empleadas en las construcciones castrenses en el ámbito temporal en que se enmarca la investigación. - Localizar, documentar y seleccionar para su análisis las fortalezas y construcciones militares erigidas durante dichas luchas fronterizas en la actual provincia de Soria a través del trabajo de campo y métodos cartográficos y bibliográficos. - Realizar un estudio general sobre el sistema fortificado a escala territorial - Investigar la tipología arquitectónica, poliorcética y constructiva del conjunto de estas fortificaciones bajomedievales fronterizas. - Analizar los fundamentos constructivos de los casos de estudio seleccionados entre estas construcciones y caracterizarlas en cuanto al material, elementos, sistemas y procesos constructivos. - Ordenar la información histórica dispersa y corregir errores para hacer una base sobre la que establecer un discurso histórico de cada caso de estudio. - Comparar y relacionar las técnicas constructivas empleadas en estas fortalezas con los utilizados en el mismo ámbito temporal. - Difundir para su debate los resultados de la investigación por los foros científicos habituales. El método empleado combina los trabajos de gabinete con una intensa labor de campo, en la que se han documentado cincuenta fortificaciones y se han redactado sus correspondientes fichas de toma de datos. La recopilación de datos se ha incluido en una base de datos que incluye aspectos generales, tipológicos, constructivos y bibliográficos básicos del conjunto, a modo de inventario, de fortificaciones de la provincia. Las fortificaciones seleccionadas se agrupan según una clasificación tipológica y constructiva que marca las líneas de estudio posteriores. Se desarrolla un capítulo de antecedentes en el que se estudia la historia de la construcción fortificada medieval tanto en Europa como en España analizando la evolución de los tipos arquitectónicos y las múltiples influencias culturales que surcaron el Mediterráneo desde el Oriente cruzado e islámico al Poniente donde se desarrollaba la empresa reconquistadora que mantuvo en estado de guerra continuo a la Península Ibérica durante ochocientos años. El análisis del territorio como contenedor del hecho fortificado revela que hay una relación íntima entre la ubicación de las fortificaciones y las formas naturales que definen las vías de comunicación entre los valles del Duero, del Ebro y del Tajo. En efecto, el ámbito de estudio ha supuesto desde la Antigüedad un territorio de paso fundamental en la articulación de las comunicaciones en la Península Ibérica. Este carácter de paso más que de frontera explica las inquietudes y la preocupación por su control tanto por Roma como por el califato cordobés como por los reinos cristianos medievales. El análisis de los elementos históricos se complementa con el estudio detallado de los enfrentamientos fronterizos entre Castilla y Aragón así como los aspectos sociales y políticos que provocaron la fortificación como sistema de definición de la frontera y de organización espacial, jurisdiccional, social y administrativa del territorio. La arquitectura fortificada es esencialmente funcional: su cometido es la defensa. En este sentido, tras un estudio morfológico de los castillos seleccionados se realiza un extenso análisis poliorcético de sus elementos, investigando su origen y aplicación para servir también de parámetros de datación. Siendo el objeto inaugural de la tesis el estudio de los fundamentos constructivos, se explican los distintos materiales de construcción empleados y se agrupan las fábricas de las fortificaciones seleccionadas en dos grandes grupos constructivos: las fábricas aparejadas y las fábricas encofradas. Se han destacado y estudiado la evolución histórica y la tipología y mensiología constructiva de tres técnicas destacadas: el uso del ladrillo, la tapia de cal y canto o mampostería encofrada y la tapia de tierra. Para el estudio de la componente histórica y de la dimensión constructiva de cada técnica ha sido necesario documentar numerosos casos tanto en el ámbito de estudio como en la Península Ibérica con el fin de establecer grupos cronotipológicos constructivos entre los que poder ubicar las fábricas de estas técnicas presentes en el ámbito de estudio. Se ha observado una evolución dimensional de las fábricas de tapia que es más evidente en las hispanomusulmanas al modularse en codos pero que también se advierte significativamente en las cristianas bajomedievales. De cada una de las técnicas analizadas se ha seleccionado un caso de estudio singular y representativo. El castillo de Arcos de Jalón es un ejemplo significativo del empleo de la fábrica mixta de mampostería con verdugadas de ladrillo, así como las murallas de la ciudad fortificada de Peñalcázar lo es de la fábrica de mampostería encofrada y el castillo de Serón de Nágima constituye un caso característico y principal de la utilización de la tapia de tierra en la arquitectura militar bajomedieval. Cada uno de estos tres casos de estudios se examina bajo los mismos cuatro niveles anteriormente mencionados: territorial, histórico, arquitectónico y defensivo y constructivo. El sistemático método de estudio ha facilitado el orden en la investigación y la obtención de unos resultados y conclusiones que verifican la hipótesis y cumplen los objetivos marcados al comienzo. Se ha revisado la datación en la construcción de las fortificaciones analizadas mediante el estudio cronotipológico de sus fábricas, pudiendo trasladarse el método a otros sistemas fortificados. La tesis abre, finalmente, dos vías principales de investigación encaminadas a completar el estudio del sistema fortificado fronterizo bajomedieval en la raya oriental soriana de Castilla: la caracterización y datación por métodos físico-químicos de las muestras de piezas de madera de construcción que se conservan embebidas en las fábricas y la búsqueda documental y archivística que pueda revelar nuevos datos respecto a la fundación, reparación, venta o cualquier aspecto económico, legislativo, organizativo o administrativo relativo a las fortificaciones en documentos coetáneos. ABSTRACT The doctoral thesis develops an original research, held in the field of the Construction History, about the constructive reason of the frontier fortifications in the Late Middle Age between the Crowns of Castile and Aragón in the actual province of Soria, Spain. In the title is expressed the main objective, and also the temporal scope —from the reconquest in the 12th Century by Alfonso the First of Aragón to the unification under the common kingdom of the Catholic Kings— and the territorial extension that the research delimits: those Castilian regions in the border with Aragón in the actual province of Soria. During this period, a series of border wars were been, and this is the reason for the fortification of the border line and the main roads between both Crowns. The lack of studies of these fortifications as participants in a fortified system is the justification of the research. There is several analysis levels: territorial, historical, architectonic, defensive and constructive. Likewise, there is a lack of strictness and inaccuracy in the constructive items in the publications about several fortifications of this study field. This aspect has caused mistakes in the dating because there is neither artistic nor stylistic elements which determines a epoch. The traditionally accepted datings are challenged. An hypothesis is formulated: in the absence of artistic or stylistic elements in a sober and functional buildings is possible to date the time of construction with sufficiently approximation based on construction criteria once formed a cronotypologic classification of each building technique. The hypothesis, therefore, propose a main aim: the study of the constructive reason of the fortified border system. This aim is developed in a series of specifically targets whose achievement programs the analysis levels: - To know and to detail the historical elements which started the wars between Castile and Aragon and its development using historiographical tools, and to analyze the natural characteristic of the territory through cartographical tools. - To understand and to analyze the different architectural types and the building traditions employed in the military buildings in the time researched. - To locate, to document, and to select for their analysis the fortresses and military constructions erected during these border wars in the actual province of Soria through fieldwork and bibliographical and cartographical methods. - To conduct a general study on the fortified system in territorial scale. - To research the architectural, constructive and defensive typology of the system of these border late medieval fortifications. - To analyze the construction logic of the selected case studies and to characterize in the items of material, elements, systems and construction processes. - To sort scattered historical information and to correct mistakes to make a base by which to establish a historic speech of each case study. - To compare and to relate the construction techniques employed in these fortresses with those used in the same time range . - To spread for discussion the research results in the usual scientists forums. The method combines the destock work with an intense fieldwork. Fifty fortifications have been documented and it has written their corresponding data collection card. Data collection has been included in a database that includes general aspects, typological, constructive and basic bibliographical data, as an inventory of fortifications in the province. The selected fortifications are grouped according to a typological and constructive classification which lead the lines of the later study. There is a chapter for the antecedents in which the history of the medieval fortified construction in Europe and in Spain is studied by analyzing the evolution of architectural types and the many cultural influences along the opposite seasides of the Mediterranean Sea, from the Islamic and Crusader East to the Iberian Peninsula in where there were a long and continuous war during eight hundred years. The territory is analyzed as a container of fortifications. This analysis reveals that there is an intimate relationship between the location of the fortifications and the natural forms that define the communication roads between the Duero, Ebro and Tajo valleys. Indeed, the study area has been a cross-territory from ancient times more than a frontierterritory. This communication character explains the concerns about its control both by Rome and by the Muslims of Córdoba as medieval Christian kingdoms. The analysis of historical elements is supplemented by detailed study of border war between Castile and Aragon and the social and political issues that led to the fortification as border definition system and spatial, jurisdictional, social and administrative planning. The fortified architecture is essentially functional: it is responsible for defense. In this sense, after a morphological study of selected castles is performed an extensive analysis of its defensive elements, investigating its origin and application. This analisis serves for the definition of parameters for dating. The purpose of the thesis is the study of the constructive logic. First, various building materials are explained. Then, masonry is grouped into two major constructive groups: rigged masonry and formwork masonry. The historical evolution and the constructive typology and mensiology are studied for each one of the three main techniques: the use of brickwork, the mortar wall and rammed-earth. Many case studies have been documented along the Iberian Peninsula and also in the study area. As conclusion, there is a dimensional evolution of the rammed-earth walls. This evolution is more evident into the Muslim masonry than in the late medieval walls: the reason is the use of the cubit as module. From each of the techniques discussed, a singular and representative case of study has been selected. The castle of Arcos de Jalon is a significant example of mix masonry of stone and brick rows. The walled city of Peñalcázar is built with masonry formwork. Serón de Nágima castle, at last, is a typical and main case of the use of the rammedearth wall of late medieval military architecture. Each of these three case studies were examined under the same four analysis levels above mentioned: territorial, historical, architectural and defensive and constructive. The systematic method of study has facilitated the order in the research and the obtaining of results and conclusions that verify the hypotheses and achieve the research objectives. Dating of the fortifications construction has been revised by studying the cronotypological issues of its masonry. The method can be transferred to the study of other fortified systems. Finally, the thesis describes two main research new ways aimed at completing the study of the late medieval fortified border of Castile in the actual province of Soria. The first of them is the characterization and datig by physicochemical methods the sample pieces of wood construction preserved embedded in the masonry. The second research way is the investigation of the documents in archives that may reveal new information about the foundation, repair, sale or any aspect to economic, legal, organizational or administrative concerning fortifications in contemporary documents.

Some advances in extensive bridge monitoring using low cost dynamic characterization

Dynamic measurements will become a standard for bridge monitoring in the near future. This fact will produce an important cost reduction for maintenance. US Administration has a long term intensive research program in order to diminish the estimated current maintenance cost of US$7 billion per year over 20 years. An optimal intervention maintenance program demands a historical dynamical record, as well as an updated mathematical model of the structure to be monitored. In case that a model of the structure is not actually available it is possible to produce it, however this possibility does not exist for missing measurement records from the past. Current acquisition systems to monitor structures can be made more efficient by introducing the following improvements, under development in the Spanish research Project “Low cost bridge health monitoring by ambient vibration tests using wireless sensors”: (a) a complete wireless system to acquire sensor data, (b) a wireless system that permits the localization and the hardware identification of the whole sensor system. The applied localization system has been object of a recent patent, and (c) automatization of the modal identification process, aimed to diminish human intervention. This system is assembled with cheap components and allows the simultaneous use of a large number of sensors at a low placement cost. The engineer’s intervention is limited to the selection of sensor positions, probably based on a preliminary FE analysis. In case of multiple setups, also the position of a number of fixed reference sensors has to be decided. The wireless localization system will obtain the exact coordinates of all these sensors positions. When the selection of optimal positions is difficult, for example because of the lack of a proper FE model, this can be compensated by using a higher number of measuring (also reference) points. The described low cost acquisition system allows the responsible bridge administration to obtain historical dynamic identification records at reasonable costs that will be used in future maintenance programs. Therefore, due to the importance of the baseline monitoring record of a new bridge, a monitoring test just after its construction should be highly recommended, if not compulsory.

A non-persistently transmitted-virus induces a pull?push strategy inits aphid vector to optimize transmission and spread

Plant viruses are known to modify the behaviour of their insect vectors, both directly and indirectly,generally adapting to each type of virus?vector relationship in a way that enhances transmissionefficiency. Here, we report results of three different studies showing how a virus transmitted in a non-persistent (NP) manner (Cucumber mosaic virus; CMV, Cucumovirus) can induce changes in its host plant,cucumber (Cucumis sativus cv. Marumba) that modifies the behaviour of its aphid vector (Aphis gossypiiGlover; Hemiptera: Aphididae) in a way that enhances virus transmission and spread non-viruliferousaphids changed their alighting, settling and probing behaviour activities over time when exposed toCMV-infected and mock-inoculated cucumber plants. Aphids exhibited no preference to migrate fromCMV-infected to mock-inoculated plants at short time intervals (1, 10 and 30 min after release), butshowed a clear shift in preference to migrate from CMV-infected to mock-inoculated plants 60 min afterrelease. Our free-choice preference assays showed that A. gossypii alates preferred CMV-infected overmock-inoculated plants at an early stage (30 min), but this behaviour was reverted at a later stage andaphids preferred to settle and reproduce on mock-inoculated plants. The electrical penetration graph(EPG) technique revealed a sharp change in aphid probing behaviour over time when exposed to CMV-infected plants. At the beginning (first 15 min) aphid vectors dramatically increased the number of shortsuperficial probes and intracellular punctures when exposed to CMV-infected plants. At a later stage (sec-ond hour of recording) aphids diminished their feeding on CMV-infected plants as indicated by much lesstime spent in phloem salivation and ingestion (E1 and E2). This particular probing behaviour includingan early increase in the number of short superficial probes and intracellular punctures followed by aphloem feeding deterrence is known to enhance the transmission efficiency of viruses transmitted in aNP manner. We conclude that CMV induces specific changes in a plant host that modify the alighting,settling and probing behaviour of its main vector A. gossypii, leading to optimum transmission and spreadof the virus. Our findings should be considered when modelling the spread of viruses transmitted in a NPmanner.

Effect of late weaning and use of alternative cages on performance of does, suckling and fattening rabbits under extensive reproductive management

The effects of the combined use of long lactation periods (46 days) with alternative cages on the reproductive and growth performance of 104 rabbit does and their litters during five consecutive reproductive cycles were studied. Half of does were housed in conventional polyvalent cages (39 cm×100 cm×30 cm) and the other half in alternative polyvalent cages (39 cm×100 cm×60 cm), with a raised platform. Half of the rabbit does in each type of cage were weaned at 32 and the other half at 46 days after parturition. Longer lactation negatively affected the body weight (P<0.001), fat and energy content (P<0.05) of rabbit does at the end of the lactation period, but this effect decreased with the number of parturitions. Fertility, prolificacy and doe mortality were not affected by lactation length. Late weaning led to higher litter size (by 8.9%) and litter weight (by 11.3%) at the end of growing period (P<0.001) and lower feed conversion ratio per cage during the experimental period (13.5%) than weaning at 32 day (P<0.001). These results were paralleled by lower mortality (12.6 vs. 17.6%; P<0.01) of young rabbits weaned later during the overall experimental period. Differences in performance as a result of different weaning ages were only observed during cycles with worst health status (third and fifth cycles) in which late weaning decreased mortality. Type of cage did not affect doe body weight and body condition, mortality, fertility, prolificacy and litter size during the five reproductive cycles. Nevertheless, at day 21 litter weight and feed conversion ratio between 3 and 21 day were 4.2% higher (P<0.01) and 5.0% lower (P<0.05), respectively, in animals housed in alternative rather than in conventional cages. Alternative cages also led to heavier litters at 59 days (P<0.01). It was concluded that the combined use of longer lactations and cages with higher available surface with a raised platform could be alternatives to improve animal welfare in farmed rabbit.

Effect of late weaning and use of alternative cages on performance of does, suckling and fattening rabbits under extensive reproductive management

The effects of the combined use of long lactation periods (46 days) with alternative cages on the reproductive and growth performance of 104 rabbit does and their litters during five consecutive reproductive cycles were studied. Half of does were housed in conven- tional polyvalent cages (39 cm x 100 cm x 30 cm) and the other half in alternative polyvalent cages (39 cm x 100 cm x 60 cm), with a raised platform. Half of the rabbit does in each type of cage were weaned at 32 and the other half at 46 days after parturition. Longer lactation negatively affected the body weight ( P o 0.001), fat and energy content ( P o 0.05) of rabbit does at the end of the lactation period, but this effect decreased with the number of parturitions. Fertility, prolificacy and doe mortality were not affected by lactation length. Late weaning led to higher litter size (by 8.9%) and litter weight (by 11.3%) at the end of growing period ( P o 0.001) and lower feed conversion ratio per cage during the experimental period (13.5%) than weaning at 32 day ( P o 0.001). These results were paralleled by lower mortality (12.6 vs. 17.6%; P o 0.01) of young rabbits weaned later during the overall experimental period. Differences in performance as a result of different weaning ages were only observed during cycles with worst health status (third and fifth cycles) in which late weaning decreased mortality. Type of cage did not affect doe body weight and body condition, mortality, fertility, prolificacy and litter size during the five reproductive cycles. Nevertheless, at day 21 litter weight and feed conversion ratio between 3 and 21 day were 4.2% higher ( P o 0.01) and 5.0% lower ( P o 0.05), respectively, in animals housed in alternative rather than in conventional cages. Alternative cages also led to heavier litters at 59 days ( P o 0.01). It was concluded that the combined use of longer lactations and cages with higher available surface with a raised platform could be alternatives to improve animal welfare in farmed rabbit.