Identification of a time-dependent bio-heat blood perfusion coefficient

In the paper the identification of the time-dependent blood perfusion coefficient is formulated as an inverse problem. The bio-heat conduction problem is transformed into the classical heat conduction problem. Then the transformed inverse problem is solved using the method of fundamental solutions together with the Tikhonov regularization. Some numerical results are presented in order to demonstrate the accuracy and the stability of the proposed meshless numerical algorithm.

Thermal effects on the photoelastic coefficient of polymer optical fibers

We measure the radial profile of the photoelastic coefficient C(r) in single-mode polymer optical fibers (POFs), and we determine the evolution of C(r) after annealing the fibers at temperatures from 40°C to 80°C. We demonstrate that C(r) in the fibers drawn from a preform without specific thermal pre-treatment changes and converges to values between 1.2 and 1.6×10-12 Pa-1 following annealing at 80°C. The annealed fibers display a smoothened radial profile of C(r) and a lowered residual birefringence. In contrast, the mean value of C(r) of the fiber drawn from a preform that has been pre-annealed remains constant after our annealing process and is significantly higher, i.e., 4×10-12 Pa-1. The annealing process decreases the residual birefringence to a lower extent as well. These measurements indicate the impact of annealing on the thermal stability of the photoelastic coefficient of POFs, which is an essential characteristic in view of developing POF-based thermomechanical sensors.

Measurements of stress-optic coefficient and Young's modulus in PMMA fibers drawn under different conditions

We have systematically measured the differential stress-optic coefficient, ΔC, and Young's modulus, E, in a number of PMMA fibers drawn with different stress, ranging from 2 up to 27 MPa. Effect of temperature annealing on those parameters was also investigated. ΔC was determined in transverse illumination by measuring the dependence of birefringence on additional axial stress applied to the fiber. Our results show that ΔC in PMMA fibers has a negative sign and ranges from -4.5 to -1.5×10-12 Pa -1 depending on the drawing stress. Increase of the drawing stress results in greater initial fiber birefringence and lower ΔC. The dependence of ΔC and initial birefringence upon drawing stress is nonlinear and gradually saturates for higher drawing stress. Moreover, we find that ΔC is linearly proportional to initial fiber birefringence and that annealing the fiber has no impact on the slope of this dependence. On the other hand, no clear dependence was observed between the fiber drawing stress and the Young's modulus of the fibers as measured using microscopic digital image correlation with the fibers tensioned using an Instron tension tester. © 2010 SPIE.

Biomass, quality traits and methane production of extensive grassland: biodiversity effects and sensor approaches

Energy policies around the world are mandating for a progressive increase in renewable energy production. Extensive grassland areas with low productivity and land use limitations have become target areas for sustainable energy production to avoid competition with food production on the limited available arable land resources and minimize further conversion of grassland into intensively managed energy cropping systems or abandonment. However, the high spatio-temporal variability in botanical composition and biochemical parameters is detrimental to reliable assessment of biomass yield and quality regarding anaerobic digestion. In an approach to assess the performance for predicting biomass using a multi-sensor combination including NIRS, ultra-sonic distance measurements and LAI-2000, biweekly sensor measurements were taken on a pure stand of reed canary grass (Phalaris aruninacea), a legume grass mixture and a diversity mixture with thirty-six species in an experimental extensive two cut management system. Different combinations of the sensor response values were used in multiple regression analysis to improve biomass predictions compared to exclusive sensors. Wavelength bands for sensor specific NDVI-type vegetation indices were selected from the hyperspectral data and evaluated for the biomass prediction as exclusive indices and in combination with LAI and ultra-sonic distance measurements. Ultrasonic sward height was the best to predict biomass in single sensor approaches (R² 0.73 – 0.76). The addition of LAI-2000 improved the prediction performance by up to 30% while NIRS barely improved the prediction performance. In an approach to evaluate broad based prediction of biochemical parameters relevant for anaerobic digestion using hyperspectral NIRS, spectroscopic measurements were taken on biomass from the Jena-Experiment plots in 2008 and 2009. Measurements were conducted on different conditions of the biomass including standing sward, hay and silage and different spectroscopic devices to simulate different preparation and measurement conditions along the process chain for biogas production. Best prediction results were acquired for all constituents at laboratory measurement conditions with dried and ground samples on a bench-top NIRS system (RPD > 3) with a coefficient of determination R2 < 0.9. The same biomass was further used in batch fermentation to analyse the impact of species richness and functional group composition on methane yields using whole crop digestion and pressfluid derived by the Integrated generation of solid Fuel and Biogas from Biomass (IFBB) procedure. Although species richness and functional group composition were largely insignificant, the presence of grasses and legumes in the mixtures were most determining factors influencing methane yields in whole crop digestion. High lignocellulose content and a high C/N ratio in grasses may have reduced the digestibility in the first cut material, excess nitrogen may have inhibited methane production in second cut legumes, while batch experiments proved superior specific methane yields of IFBB press fluids and showed that detrimental effects of the parent material were reduced by the technical treatment

Analysis of heat transfer coefficient in silica nanofluids with water as base fluid under transitional flow

The effect of Reynolds number variation in a vertical double pipe counterflow heat exchanger due to the changes in viscosity can cause the change in flow regime, for instance, when heats up and cools down, it can convert from turbulent to laminar or inversely, that can have significant effect on heat transfer coefficient and pressure drop. Mainly, the range of transition phase has been studied in this study with the investigation of silica nanofluid dispersed in water in three different concentrations. The results have been compared with distilled water sample and showed a remarkable raise in heat transfer coefficient while pressure drop has been increased respectively, as well. Although pumping power has to go up at the same time and it is a drawback, heat transfer efficiency grows for diluted samples. On the other hand, for the most concentrated sample, effect of pressure drop dominates which leads to decline in the overall efficiency.

Controller system design using the coefficient diagram method

Coefficient diagram method is a controller design technique for linear time-invariant systems. This design procedure occurs into two different domains: an algebraic and a graphical. The former is closely paired to a conventional pole placement method and the latter consists on a diagram whose reading from the plotted curves leads to insights regarding closed-loop control system time response, stability and robustness. The controller structure has two degrees of freedom and the design process leads to both low overshoot closed-loop time response and good robustness performance regarding mismatches between the real system and the design model. This article presents an overview on this design method. In order to make more transparent the presented theoretical concepts, examples in Matlab®code are provided. The included code illustrates both the algebraic and the graphical nature of the coefficient diagram design method. © 2016, King Fahd University of Petroleum & Minerals.

Diversity and path coefficient analysis of Southern African maize hybrids

Detailed knowledge on genetic diversity among germplasm is important for hybrid maize ( Zea mays L.) breeding. The objective of the study was to determine genetic diversity in widely grown hybrids in Southern Africa, and compare effectiveness of phenotypic analysis models for determining genetic distances between hybrids. Fifty hybrids were evaluated at one site with two replicates. The experiment was a randomized complete block design. Phenotypic and genotypic data were analyzed using SAS and Power Marker respectively. There was significant (p < 0.01) variation and diversity among hybrid brands but small within brand clusters. Polymorphic Information Content (PIC) ranged from 0.07 to 0.38 with an average of 0.34 and genetic distance ranged from 0.08 to 0.50 with an average of 0.43. SAH23 and SAH21 (0.48) and SAH33 and SAH3 (0.47) were the most distantly related hybrids. Both single nucleotide polymorphism (SNP) markers and phenotypic data models were effective for discriminating genotypes according to genetic distance. SNP markers revealed nine clusters of hybrids. The 12-trait phenotypic analysis model, revealed eight clusters at 85%, while the five-trait model revealed six clusters. Path analysis revealed significant direct and indirect effects of secondary traits on yield. Plant height and ear height were negatively correlated with grain yield meaning shorter hybrids gave high yield. Ear weight, days to anthesis, and number of ears had highest positive direct effects on yield. These traits can provide good selection index for high yielding maize hybrids. Results confirmed that diversity of hybrids is small within brands and also confirm that phenotypic trait models are effective for discriminating hybrids.

On the temperature dependence of the rate coefficient of formation of C2+ from C + CH+

[EN] We carry out quasi-classical trajectory caculations for theC + CH+ → C2+ + H reaction on an ad hoc computed high-level ab initio potential energy surface. Thermal rate coefficients at the temperatures of relevance in cold interstellar clouds are derived and compared with the assumed, temperature-independent estimates publicly available in kinetic databases KIDA and UDfA. For a temperature of 10 K the database value overestimates by a factor of two the one obtained by us (thus improperly enhancing the destruction route of CH+ in astrochemical kinetic models) which is seen to double in the temperature range 5–300 K with a sharp increase in the first 50 K. The computed values are fitted via the popular Arrhenius–Kooij formula and best-fitting parameters α = 1:32 X 10-9 cm3s-1, β = 0:10 and γ = 2:19 K to be included in the online mentioned databases are provided. Further investigation shows that the temperature dependence of the thermal rate coefficient better conforms to the recently proposed so-called ‘deformed Arrhenius’ law by Aquilanti and Mundim.

Efeitos de absorventes de umidade e de aditivos químicos e microbianos sobre o valor nutritivo, o perfil fermentativo e as perdas em silagens de capim-marandu

The objective of this trial was to evaluate the nutritional value, fermentation profile and dry matter losses of Palisadegrass silages ensiled with either dried citrus pulp, soybean hulls, chemical or microbial additives. The trial was carried out in a completely randomized experimental design and in a factorial arrangement (3 x 5), with three dry matter levels (wet forage or forage ensiled with pelleted citrus pulp or pelleted soybean hulls) and five additives (without or with the presence of bacterial inoculants or the addition of: sodium benzoate, formic acid in the concentration of 62% or 44%), totalizing 15 treatments and 60 experimental silos. The variables analyzed were: nutritional value, losses due to gases and effluents, and dry matter recovery. The use of dried citrus pulp or soybean hulls at the ensiling time increased the dry matter content (29.4 and 28,9%) and decreased the effluent production (4.1 and 3.8 kg/t of fresh matter), also providing fermentable substrate to microorganisms, resulting in increased fermentation coefficient and digestibility of silages. The use of formic acid resulted in silages with higher digestibility and increased water-soluble carbohydrates and crude protein content. This additive was also effective in reducing the losses due to gases and, as a result, increased the total dry matter recovery. The treatment containing homolactic bacteria showed similar trend of increasing the digestibility and reducing the losses due to gases. The use of sodium benzoate was less effective in altering the fermentation pattern of tropical silages. The nutritional value and total dry matter losses of silages ensiled without additives can be considered satisfactory. However, wet forage ensiled with dried citrus pulp and, mainly, with soybeans hulls showed the best results. Treatments containing formic acid had a beneficial effect on the fermentation profile of tropical grass silages.