Effect of X-ray tube parameters, iodine concentration, and patient size on image quality in pulmonary computed tomography angiography: a chest-phantom-study

OBJECTIVES: The aim of this phantom study was to evaluate the contrast-to-noise ratio (CNR) in pulmonary computed tomography (CT)-angiography for 300 and 400 mg iodine/mL contrast media using variable x-ray tube parameters and patient sizes. We also analyzed the possible strategies of dose reduction in patients with different sizes. MATERIALS AND METHODS: The segmental pulmonary arteries were simulated by plastic tubes filled with 1:30 diluted solutions of 300 and 400 mg iodine/mL contrast media in a chest phantom mimicking thick, intermediate, and thin patients. Volume scanning was done with a CT scanner at 80, 100, 120, and 140 kVp. Tube current-time products (mAs) varied between 50 and 120% of the optimal value given by the built-in automatic dose optimization protocol. Attenuation values and CNR for both contrast media were evaluated and compared with the volume CT dose index (CTDI(vol)). Figure of merit, calculated as CNR/CTDIvol, was used to quantify image quality improvement per exposure risk to the patient. RESULTS: Attenuation of iodinated contrast media increased both with decreasing tube voltage and patient size. A CTDIvol reduction by 44% was achieved in the thin phantom with the use of 80 instead of 140 kVp without deterioration of CNR. Figure of merit correlated with kVp in the thin phantom (r = -0.897 to -0.999; P < 0.05) but not in the intermediate and thick phantoms (P = 0.09-0.71), reflecting a decreasing benefit of tube voltage reduction on image quality as the thickness of the phantom increased. Compared with the 300 mg iodine/mL concentration, the same CNR for 400 mg iodine/mL contrast medium was achieved at a lower CTDIvol by 18 to 40%, depending on phantom size and applied tube voltage. CONCLUSIONS: Low kVp protocols for pulmonary embolism are potentially advantageous especially in thin and, to a lesser extent, in intermediate patients. Thin patients profit from low voltage protocols preserving a good CNR at a lower exposure. The use of 80 kVp in obese patients may be problematic because of the limitation of the tube current available, reduced CNR, and high skin dose. The high CNR of the 400 mg iodine/mL contrast medium together with lower tube energy and/or current can be used for exposure reduction.

Analyzing the effects of vertical acceleration and deceleration in multi-phase, debris-flow sediment-column experiments / by Christine Marie Williams.

Water-saturated debris flows are among some of the most destructive mass movements. Their complex nature presents a challenge for quantitative description and modeling. In order to improve understanding of the dynamics of these flows, it is important to seek a simplified dynamic system underlying their behavior. Models currently in use to describe the motion of debris flows employ depth-averaged equations of motion, typically assuming negligible effects from vertical acceleration. However, in many cases debris flows experience significant vertical acceleration as they move across irregular surfaces, and it has been proposed that friction associated with vertical forces and liquefaction merit inclusion in any comprehensive mechanical model. The intent of this work is to determine the effect of vertical acceleration through a series of laboratory experiments designed to simulate debris flows, testing a recent model for debris flows experimentally. In the experiments, a mass of water-saturated sediment is released suddenly from a holding container, and parameters including rate of collapse, pore-fluid pressure, and bed load are monitored. Experiments are simplified to axial geometry so that variables act solely in the vertical dimension. Steady state equations to infer motion of the moving sediment mass are not sufficient to model accurately the independent solid and fluid constituents in these experiments. The model developed in this work more accurately predicts the bed-normal stress of a saturated sediment mass in motion and illustrates the importance of acceleration and deceleration.

Development of an optimization model for biofuel facility size and location and a simulation model for design of a biofuel supply chain

To mitigate greenhouse gas (GHG) emissions and reduce U.S. dependence on imported oil, the United States (U.S.) is pursuing several options to create biofuels from renewable woody biomass (hereafter referred to as “biomass”). Because of the distributed nature of biomass feedstock, the cost and complexity of biomass recovery operations has significant challenges that hinder increased biomass utilization for energy production. To facilitate the exploration of a wide variety of conditions that promise profitable biomass utilization and tapping unused forest residues, it is proposed to develop biofuel supply chain models based on optimization and simulation approaches. The biofuel supply chain is structured around four components: biofuel facility locations and sizes, biomass harvesting/forwarding, transportation, and storage. A Geographic Information System (GIS) based approach is proposed as a first step for selecting potential facility locations for biofuel production from forest biomass based on a set of evaluation criteria, such as accessibility to biomass, railway/road transportation network, water body and workforce. The development of optimization and simulation models is also proposed. The results of the models will be used to determine (1) the number, location, and size of the biofuel facilities, and (2) the amounts of biomass to be transported between the harvesting areas and the biofuel facilities over a 20-year timeframe. The multi-criteria objective is to minimize the weighted sum of the delivered feedstock cost, energy consumption, and GHG emissions simultaneously. Finally, a series of sensitivity analyses will be conducted to identify the sensitivity of the decisions, such as the optimal site selected for the biofuel facility, to changes in influential parameters, such as biomass availability and transportation fuel price. Intellectual Merit The proposed research will facilitate the exploration of a wide variety of conditions that promise profitable biomass utilization in the renewable biofuel industry. The GIS-based facility location analysis considers a series of factors which have not been considered simultaneously in previous research. Location analysis is critical to the financial success of producing biofuel. The modeling of woody biomass supply chains using both optimization and simulation, combing with the GIS-based approach as a precursor, have not been done to date. The optimization and simulation models can help to ensure the economic and environmental viability and sustainability of the entire biofuel supply chain at both the strategic design level and the operational planning level. Broader Impacts The proposed models for biorefineries can be applied to other types of manufacturing or processing operations using biomass. This is because the biomass feedstock supply chain is similar, if not the same, for biorefineries, biomass fired or co-fired power plants, or torrefaction/pelletization operations. Additionally, the research results of this research will continue to be disseminated internationally through publications in journals, such as Biomass and Bioenergy, and Renewable Energy, and presentations at conferences, such as the 2011 Industrial Engineering Research Conference. For example, part of the research work related to biofuel facility identification has been published: Zhang, Johnson and Sutherland [2011] (see Appendix A). There will also be opportunities for the Michigan Tech campus community to learn about the research through the Sustainable Future Institute.

Negative index metamaterials and metaspacers for optical frequencies

Metamaterials are artificial materials that exhibit properties, such as negative index of refraction, that are not possible through natural materials. Due to many potential applications of negative index metamaterials, significant progress in the field has been observed in the last decade. However, achieving negative index at visible frequencies is a challenging task. Generally, fishnet metamaterials are considered as a possible route to achieve negative index in the visible spectrum. However, so far no metamaterial has been demonstrated to exhibit simultaneously negative permittivity and permeability (double-negative) beyond the red region of the visible spectrum. This study is mainly focused on achieving higher operating frequency for low-loss, double-negative metamaterials. Two double-negative metamaterials have been proposed to operate at highest reported frequencies. The first proposed metamaterial is based on the interaction of surface plasmon polaritons of a thin metal film with localized surface plasmons of a metallic array placed close to the thin film. It is demonstrated that the metamaterial can easily be scaled to operate at any frequency in the visible spectrum as well as possibly to the ultraviolet spectrum. Furthermore, the underlying physical phenomena and possible future extensions of the metamaterial are also investigated. The second proposed metamaterial is a modification to the so-called fishnet metamaterial. It has been demonstrated that this ‘modified fishnet’ exhibits two double-negative bands in the visible spectrum with highest operating frequency in the green region with considerably high figure of merit. In contrast to most of the fishnet metamaterials proposed in the past, behavior of this modified fishnet is independent of polarization of the incident field. In addition to the two negative index metamaterials proposed in this study, the use of metamaterial as a spacer, named as metaspacer, is also investigated. In contrast to naturally available dielectric spacers used in microfabrication, metaspacers can be realized with any (positive or negative) permittivity and permeability. As an example, the use of a negative index metaspacer in place of the dielectric layer in a fishnet metamaterial is investigated. It is shown that fishnet based on negative index metaspacer gives many improved optical properties over the conventional fishnet such as wider negative index band, higher figure of merit, higher optical transmission and stronger magnetic response. In addition to the improved properties, following interesting features were observed in the metaspacer based fishnet metamaterial. At the resonance frequency, the shape of the permeability curve was ‘inverted’ as compared to that for conventional fishnet metamaterial. Furthermore, dependence of the resonance frequency on the fishnet geometry was also reversed. Moreover, simultaneously negative group and phase velocities were observed in the low-loss region of the metaspacer based fishnet metamaterial. Due to interesting features observed using metaspacer, this study will open a new horizon for the metamaterial research.

Analysis of transport properties of mechanically alloyed [Pb1-xSnxTe]

The work described in this thesis had two objectives. The first objective was to develop a physically based computational model that could be used to predict the electronic conductivity, Seebeck coefficient, and thermal conductivity of Pb1-xSnxTe alloys over the 400 K to 700 K temperature as a function of Sn content and doping level. The second objective was to determine how the secondary phase inclusions observed in Pb1-xSnxTe alloys made by consolidating mechanically alloyed elemental powders impact the ability of the material to harvest waste heat and generate electricity in the 400 K to 700 K temperature range. The motivation for this work was that though the promise of this alloy as an unusually efficient thermoelectric power generator material in the 400 K to 700 K range had been demonstrated in the literature, methods to reproducibly control and subsequently optimize the materials thermoelectric figure of merit remain elusive. Mechanical alloying, though not typically used to fabricate these alloys, is a potential method for cost-effectively engineering these properties. Given that there are deviations from crystalline perfection in mechanically alloyed material such as secondary phase inclusions, the question arises as to whether these defects are detrimental to thermoelectric function or alternatively, whether they enhance thermoelectric function of the alloy. The hypothesis formed at the onset of this work was that the small secondary phase SnO2 inclusions observed to be present in the mechanically alloyed Pb1-xSnxTe would increase the thermoelectric figure of merit of the material over the temperature range of interest. It was proposed that the increase in the figure of merit would arise because the inclusions in the material would not reduce the electrical conductivity to as great an extent as the thermal conductivity. If this were to be true, then the experimentally measured electronic conductivity in mechanically alloyed Pb1-xSnxTe alloys that have these inclusions would not be less than that expected in alloys without these inclusions while the portion of the thermal conductivity that is not due to charge carriers (the lattice thermal conductivity) would be less than what would be expected from alloys that do not have these inclusions. Furthermore, it would be possible to approximate the observed changes in the electrical and thermal transport properties using existing physical models for the scattering of electrons and phonons by small inclusions. The approach taken to investigate this hypothesis was to first experimentally characterize the mobile carrier concentration at room temperature along with the extent and type of secondary phase inclusions present in a series of three mechanically alloyed Pb1-xSnxTe alloys with different Sn content. Second, the physically based computational model was developed. This model was used to determine what the electronic conductivity, Seebeck coefficient, total thermal conductivity, and the portion of the thermal conductivity not due to mobile charge carriers would be in these particular Pb1-xSnxTe alloys if there were to be no secondary phase inclusions. Third, the electronic conductivity, Seebeck coefficient and total thermal conductivity was experimentally measured for these three alloys with inclusions present at elevated temperatures. The model predictions for electrical conductivity and Seebeck coefficient were directly compared to the experimental elevated temperature electrical transport measurements. The computational model was then used to extract the lattice thermal conductivity from the experimentally measured total thermal conductivity. This lattice thermal conductivity was then compared to what would be expected from the alloys in the absence of secondary phase inclusions. Secondary phase inclusions were determined by X-ray diffraction analysis to be present in all three alloys to a varying extent. The inclusions were found not to significantly degrade electrical conductivity at temperatures above ~ 400 K in these alloys, though they do dramatically impact electronic mobility at room temperature. It is shown that, at temperatures above ~ 400 K, electrons are scattered predominantly by optical and acoustical phonons rather than by an alloy scattering mechanism or the inclusions. The experimental electrical conductivity and Seebeck coefficient data at elevated temperatures were found to be within ~ 10 % of what would be expected for material without inclusions. The inclusions were not found to reduce the lattice thermal conductivity at elevated temperatures. The experimentally measured thermal conductivity data was found to be consistent with the lattice thermal conductivity that would arise due to two scattering processes: Phonon phonon scattering (Umklapp scattering) and the scattering of phonons by the disorder induced by the formation of a PbTe-SnTe solid solution (alloy scattering). As opposed to the case in electrical transport, the alloy scattering mechanism in thermal transport is shown to be a significant contributor to the total thermal resistance. An estimation of the extent to which the mean free time between phonon scattering events would be reduced due to the presence of the inclusions is consistent with the above analysis of the experimental data. The first important result of this work was the development of an experimentally validated, physically based computational model that can be used to predict the electronic conductivity, Seebeck coefficient, and thermal conductivity of Pb1-xSnxTe alloys over the 400 K to 700 K temperature as a function of Sn content and doping level. This model will be critical in future work as a tool to first determine what the highest thermoelectric figure of merit one can expect from this alloy system at a given temperature and, second, as a tool to determine the optimum Sn content and doping level to achieve this figure of merit. The second important result of this work is the determination that the secondary phase inclusions that were observed to be present in the Pb1-xSnxTe made by mechanical alloying do not keep the material from having the same electrical and thermal transport that would be expected from “perfect" single crystal material at elevated temperatures. The analytical approach described in this work will be critical in future investigations to predict how changing the size, type, and volume fraction of secondary phase inclusions can be used to impact thermal and electrical transport in this materials system.

Isopach Maps and Discussion of the Ordovician and Devonian of Montana and Adjacent Areas

The intensive postwar search for new petroleum horizons has resulted in widespread prospecting in the northern Great Plains. No commercial production has as yet been derived from Ordovician or Devonian rocks in Montana, but the relat­ively few tests that have penetrated to critical depths have disclosed encouraging conditions which merit further consider­ation, especially in Devonian strata.

Past is Prologue: Montana’s Historic Women’s Movement Re-emerges in the Progressive 1970s -- Dorothy Bradley, Marilyn Wessel & Jane Jelinski “In the Crucible of Change”

One-hundred years ago, in 1914, male voters in Montana (MT) extended suffrage (voting rights) to women six years before the 19th Amendment to the US Constitution was ratified and provided that right to women in all states. The long struggle for women’s suffrage was energized in the progressive era and Jeanette Rankin of Missoula emerged as a leader of the campaign; in 1912 both major MT political party platforms supported women suffrage. In the 1914 election, 41,000 male voters supported woman suffrage while nearly 38,000 opposed it. MT was not only ahead of the curve on women suffrage, but just two years later in 1916 elected Jeanette Rankin as the first woman ever elected to the United States Congress. Rankin became a national leader for women's equality. In her commitment to equality, she opposed US entry into World War I, partially because she said she could not support men being made to go to war if women were not allowed to serve alongside them. During MT’s initial progressive era, women in MT not only pursued equality for themselves (the MT Legislature passed an equal pay act in 1919), but pursued other social improvements, such as temperance/prohibition. Well-known national women leaders such as Carrie Nation and others found a welcome in MT during the period. Women's role in the trade union movement was evidenced in MT by the creation of the Women's Protective Union in Butte, the first union in America dedicated solely to women workers. But Rankin’s defeat following her vote against World War I was used as a way for opponents to advocate a conservative, traditionalist perspective on women's rights in MT. Just as we then entered a period in MT where the “copper collar” was tightened around MT economically and politically by the Anaconda Company and its allies, we also found a different kind of conservative, traditionalist collar tightened around the necks of MT women. The recognition of women's role during World War II, represented by “Rosie the Riveter,” made it more difficult for that conservative, traditionalist approach to be forever maintained. In addition, women's role in MT agriculture – family farms and ranches -- spoke strongly to the concept of equality, as farm wives were clearly active partners in the agricultural enterprises. But rural MT was, by and large, the bastion of conservative values relative to the position of women in society. As the period of “In the Crucible of Change” began, the 1965 MT Legislature included only three women. In 1967 and 1969 only one woman legislator served. In 1971 the number went up to two, including one of our guests, Dorothy Bradley. It was only after the Constitutional Convention, which featured 19 women delegates, that the barrier was broken. The 1973 Legislature saw 9 women elected. The 1975 and 1977 sessions had 14 women legislators; 15 were elected for the 1979 session. At that time progressive women and men in the Legislature helped implement the equality provisions of the new MT Constitution, ratified the federal Equal Rights Amendment in 1974, and held back national and local conservatives forces which sought in later Legislatures to repeal that ratification. As with the national movement at the time, MT women sought and often succeeded in adopting legal mechanisms that protected women’s equality, while full equality in the external world remained (and remains) a treasured objective. The story of the re-emergence of Montana’s women’s movement in the 1970s is discussed in this chapter by three very successful and prominent women who were directly involved in the effort: Dorothy Bradley, Marilyn Wessel, and Jane Jelinski. Their recollections of the political, sociological and cultural path Montana women pursued in the 1970s and the challenges and opposition they faced provide an insider’s perspective of the battle for equality for women under the Big Sky “In the Crucible of Change.” Dorothy Bradley grew up in Bozeman, Montana; received her Bachelor of Arts Phi Beta Kappa from Colorado College, Colorado Springs, in 1969 with a Distinction in Anthropology; and her Juris Doctor from American University in Washington, D.C., in 1983. In 1970, at the age of 22, following the first Earth Day and running on an environmental platform, Ms. Bradley won a seat in the 1971 Montana House of Representatives where she served as the youngest member and only woman. Bradley established a record of achievement on environmental & progressive legislation for four terms, before giving up the seat to run a strong second to Pat Williams for the Democratic nomination for an open seat in Montana’s Western Congressional District. After becoming an attorney and an expert on water law, she returned to the Legislature for 4 more terms in the mid-to-late 1980s. Serving a total of eight terms, Dorothy was known for her leadership on natural resources, tax reform, economic development, and other difficult issues during which time she gained recognition for her consensus-building approach. Campaigning by riding her horse across the state, Dorothy was the Democratic nominee for Governor in 1992, losing the race by less than a percentage point. In 1993 she briefly taught at a small rural school next to the Northern Cheyenne Indian Reservation. She was then hired as the Director of the Montana University System Water Center, an education and research arm of Montana State University. From 2000 - 2008 she served as the first Gallatin County Court Administrator with the task of collaboratively redesigning the criminal justice system. She currently serves on One Montana’s Board, is a National Advisor for the American Prairie Foundation, and is on NorthWestern Energy’s Board of Directors. Dorothy was recognized with an Honorary Doctorate from her alma mater, Colorado College, was named Business Woman of the Year by the Bozeman Chamber of Commerce and MSU Alumni Association, and was Montana Business and Professional Women’s Montana Woman of Achievement. Marilyn Wessel was born in Iowa, lived and worked in Los Angeles, California, and Washington, D.C. before moving to Bozeman in 1972. She has an undergraduate degree in journalism from Iowa State University, graduate degree in public administration from Montana State University, certification from the Harvard University Institute for Education Management, and served a senior internship with the U.S. Congress, Montana delegation. In Montana Marilyn has served in a number of professional positions, including part-time editor for the Montana Cooperative Extension Service, News Director for KBMN Radio, Special Assistant to the President and Director of Communications at Montana State University, Director of University Relations at Montana State University and Dean and Director of the Museum of the Rockies at MSU. Marilyn retired from MSU as Dean Emeritus in 2003. Her past Board Service includes Montana State Merit System Council, Montana Ambassadors, Vigilante Theater Company, Montana State Commission on Practice, Museum of the Rockies, Helena Branch of the Ninth District Federal Reserve Bank, Burton K. Wheeler Center for Public Policy, Bozeman Chamber of Commerce, and Friends of KUSM Public Television. Marilyn’s past publications and productions include several articles on communications and public administration issues as well as research, script preparation and presentation of several radio documentaries and several public television programs. She is co-author of one book, 4-H An American Idea: A History of 4-H. Marilyn’s other past volunteer activities and organizations include Business and Professional Women, Women's Political Caucus, League of Women Voters, and numerous political campaigns. She is currently engaged professionally in museum-related consulting and part-time teaching at Montana State University as well as serving on the Editorial Board of the Bozeman Daily Chronicle and a member of Pilgrim Congregational Church and Family Promise. Marilyn and her husband Tom, a retired MSU professor, live in Bozeman. She enjoys time with her children and grandchildren, hiking, golf, Italian studies, cooking, gardening and travel. Jane Jelinski is a Wisconsin native, with a BA from Fontbonne College in St. Louis, MO who taught fifth and seventh grades prior to moving to Bozeman in 1973. A stay-at-home mom with a five year old daughter and an infant son, she was promptly recruited by the Gallatin Women’s Political Caucus to conduct a study of Sex-Role Stereotyping in K Through 6 Reading Text Books in the Bozeman School District. Sociologist Dr. Louise Hale designed the study and did the statistical analysis and Jane read all the texts, entered the data and wrote the report. It was widely disseminated across Montana and received attention of the press. Her next venture into community activism was to lead the successful effort to downzone her neighborhood which was under threat of encroaching business development. Today the neighborhood enjoys the protections of a Historic Preservation District. During this time she earned her MPA from Montana State University. Subsequently Jane founded the Gallatin Advocacy Program for Developmentally Disabled Adults in 1978 and served as its Executive Director until her appointment to the Gallatin County Commission in 1984, a controversial appointment which she chronicled in the Fall issue of the Gallatin History Museum Quarterly. Copies of the issue can be ordered through: http://gallatinhistorymuseum.org/the-museum-bookstore/shop/. Jane was re-elected three times as County Commissioner, serving fourteen years. She was active in the Montana Association of Counties (MACO) and was elected its President in 1994. She was also active in the National Association of Counties, serving on numerous policy committees. In 1998 Jane resigned from the County Commission 6 months before the end of her final term to accept the position of Assistant Director of MACO, from where she lobbied for counties, provided training and research for county officials, and published a monthly newsletter. In 2001 she became Director of the MSU Local Government Center where she continued to provide training and research for county and municipal officials across MT. There she initiated the Montana Mayors Academy in partnership with MMIA. She taught State and Local Government, Montana Politics and Public Administration in the MSU Political Science Department before retiring in 2008. Jane has been married to Jack for 46 years, has two grown children and three grandchildren.

Lifestyle factors and colorectal cancer risk (1): systematic review and meta-analysis of associations with body mass index

OBJECTIVE: Excess body weight, defined by body mass index (BMI), may increase the risk of colorectal cancer. As a prerequisite to the determination of lifestyle attributable risks, we undertook a systematic review and meta-analysis of prospective observational studies to quantify colorectal cancer risk associated with increased BMI and explore for differences by gender, sub-site and study characteristics. METHOD: We searched MEDLINE and EMBASE (to December 2007), and other sources, selecting reports based on strict inclusion criteria. Random-effects meta-analyses and meta-regressions of study-specific incremental estimates were performed to determine the risk ratio (RR) and 95% confidence intervals (CIs) associated with a 5 kg/m(2) increase in BMI. RESULTS: We analysed 29 datasets from 28 articles, including 67,361 incident cases. Higher BMI was associated with colon (RR 1.24, 95% CIs: 1.20-1.28) and rectal (1.09, 1.05-1.14) cancers in men, and with colon cancer (1.09, 1.04-1.12) in women. Associations were stronger in men than in women for colon (P < 0.001) and rectal (P = 0.005) cancers. Associations were generally consistent across geographic populations. Study characteristics and adjustments accounted for only moderate variations of associations. CONCLUSION: Increasing BMI is associated with a modest increased risk of developing colon and rectal cancers, but this modest risk may translate to large attributable proportions in high-prevalence obese populations. Inter-gender differences point to potentially important mechanistic differences, which merit further research.

Effect of automatic tube current modulation on radiation dose and image quality for low tube voltage multidetector row CT angiography: phantom study

RATIONALE AND OBJECTIVES: To evaluate the effect of automatic tube current modulation on radiation dose and image quality for low tube voltage computed tomography (CT) angiography. MATERIALS AND METHODS: An anthropomorphic phantom was scanned with a 64-section CT scanner using following tube voltages: 140 kVp (Protocol A), 120 kVp (Protocol B), 100 kVp (Protocol C), and 80 kVp (Protocol D). To achieve similar noise, combined z-axis and xy-axes automatic tube current modulation was applied. Effective dose (ED) for the four tube voltages was assessed. Three plastic vials filled with different concentrations of iodinated solution were placed on the phantom's abdomen to obtain attenuation measurements. The signal-to-noise ratio (SNR) was calculated and a figure of merit (FOM) for each iodinated solution was computed as SNR(2)/ED. RESULTS: The ED was kept similar for the four different tube voltages: (A) 5.4 mSv +/- 0.3, (B) 4.1 mSv +/- 0.6, (C) 3.9 mSv +/- 0.5, and (D) 4.2 mSv +/- 0.3 (P > .05). As the tube voltage decreased from 140 to 80 kVp, image noise was maintained (range, 13.8-14.9 HU) (P > .05). SNR increased as the tube voltage decreased, with an overall gain of 119% for the 80-kVp compared to the 140-kVp protocol (P < .05). The FOM results indicated that with a reduction of the tube voltage from 140 to 120, 100, and 80 kVp, at constant SNR, ED was reduced by a factor of 2.1, 3.3, and 5.1, respectively, (P < .001). CONCLUSIONS: As tube voltage decreases, automatic tube current modulation for CT angiography yields either a significant increase in image quality at constant radiation dose or a significant decrease in radiation dose at a constant image quality.

Changing the Face of Traditional Education

At large, research universities, a common approach for teaching hundreds of undergraduate students at one time is the traditional, large, lecture-based course. Trends indicate that over the next decade there will be an increase in the number of large, campus courses being offered as well as larger enrollments in courses currently offered. As universities investigate alternative means to accommodate more students and their learning needs, Web-based instruction provides an attractive delivery mode for teaching large, on-campus courses. This article explores a theoretical approach regarding how Web-based instruction can be designed and developed to provide quality education for traditional, on-campus, undergraduate students. The academic debate over the merit of Web-based instruction for traditional, on-campus students has not been resolved. This study identifies and discusses instructional design theory for adapting a large, lecture-based course to the Web.

Questionnaire-based study to assess the association between management practices and mastitis within tie-stall and free-stall dairy housing systems in Switzerland.

BACKGROUND Prophylactic measures are key components of dairy herd mastitis control programs, but some are only relevant in specific housing systems. To assess the association between management practices and mastitis incidence, data collected in 2011 by a survey among 979 randomly selected Swiss dairy farms, and information from the regular test day recordings from 680 of these farms was analyzed. RESULTS The median incidence of farmer-reported clinical mastitis (ICM) was 11.6 (mean 14.7) cases per 100 cows per year. The median annual proportion of milk samples with a composite somatic cell count (PSCC) above 200,000 cells/ml was 16.1 (mean 17.3) %. A multivariable negative binomial regression model was fitted for each of the mastitis indicators for farms with tie-stall and free-stall housing systems separately to study the effect of other (than housing system) management practices on the ICM and PSCC events (above 200,000 cells/ml). The results differed substantially by housing system and outcome. In tie-stall systems, clinical mastitis incidence was mainly affected by region (mountainous production zone; incidence rate ratio (IRR) = 0.73), the dairy herd replacement system (1.27) and farmers age (0.81). The proportion of high SCC was mainly associated with dry cow udder controls (IRR = 0.67), clean bedding material at calving (IRR = 1.72), using total merit values to select bulls (IRR = 1.57) and body condition scoring (IRR = 0.74). In free-stall systems, the IRR for clinical mastitis was mainly associated with stall climate/temperature (IRR = 1.65), comfort mats as resting surface (IRR = 0.75) and when no feed analysis was carried out (IRR = 1.18). The proportion of high SSC was only associated with hand and arm cleaning after calving (IRR = 0.81) and beef producing value to select bulls (IRR = 0.66). CONCLUSIONS There were substantial differences in identified risk factors in the four models. Some of the factors were in agreement with the reported literature while others were not. This highlights the multifactorial nature of the disease and the differences in the risks for both mastitis manifestations. Attempting to understand these multifactorial associations for mastitis within larger management groups continues to play an important role in mastitis control programs.

NEW TOOLS FOR MONITORING GAMMA CAMERA UNIFORMITY

Detector uniformity is a fundamental performance characteristic of all modern gamma camera systems, and ensuring a stable, uniform detector response is critical for maintaining clinical images that are free of artifact. For these reasons, the assessment of detector uniformity is one of the most common activities associated with a successful clinical quality assurance program in gamma camera imaging. The evaluation of this parameter, however, is often unclear because it is highly dependent upon acquisition conditions, reviewer expertise, and the application of somewhat arbitrary limits that do not characterize the spatial location of the non-uniformities. Furthermore, as the goal of any robust quality control program is the determination of significant deviations from standard or baseline conditions, clinicians and vendors often neglect the temporal nature of detector degradation (1). This thesis describes the development and testing of new methods for monitoring detector uniformity. These techniques provide more quantitative, sensitive, and specific feedback to the reviewer so that he or she may be better equipped to identify performance degradation prior to its manifestation in clinical images. The methods exploit the temporal nature of detector degradation and spatially segment distinct regions-of-non-uniformity using multi-resolution decomposition. These techniques were tested on synthetic phantom data using different degradation functions, as well as on experimentally acquired time series floods with induced, progressively worsening defects present within the field-of-view. The sensitivity of conventional, global figures-of-merit for detecting changes in uniformity was evaluated and compared to these new image-space techniques. The image-space algorithms provide a reproducible means of detecting regions-of-non-uniformity prior to any single flood image’s having a NEMA uniformity value in excess of 5%. The sensitivity of these image-space algorithms was found to depend on the size and magnitude of the non-uniformities, as well as on the nature of the cause of the non-uniform region. A trend analysis of the conventional figures-of-merit demonstrated their sensitivity to shifts in detector uniformity. The image-space algorithms are computationally efficient. Therefore, the image-space algorithms should be used concomitantly with the trending of the global figures-of-merit in order to provide the reviewer with a richer assessment of gamma camera detector uniformity characteristics.

Architectural Developments in Sungai Tenang, 1902-2013

This paper treats the architectural developments in Sungai Tenang since the occupation by the Netherland's Indies in 1902 until the present. During this time great changes have occurred, among them the virtual disappearance of the traditional houses with carved planks. At the same time, much of the architectural developments can be described as the evolution of a still basically Austronesian house structure. Both these changes and the continuities merit close scrutiny, since they together reflect the persistence of the house as a powerful symbolic form that is capable of expressing changing social structures and cultural values. Up to the present, architecture in Sungai Tenang, in spite of its often modern outward appearance, is still by and large vernacular in the sense that its constructive means, its symbolic forms and its uses are firmly rooted in local traditions.

Architectural Developments in Sungai Tenang, 1902-2013

This paper treats the architectural developments in Sungai Tenang since the occupation by the Netherland's Indies in 1902 until the present. During this time great changes have occurred, among them the virtual disappearance of the traditional houses with carved planks. At the same time, much of the architectural developments can be described as the evolution of a still basically Austronesian house structure. Both these changes and the continuities merit close scrutiny, since they together reflect the persistence of the house as a powerful symbolic form that is capable of expressing changing social structures and cultural values. Up to the present, architecture in Sungai Tenang, in spite of its often modern outward appearance, is still by and large vernacular in the sense that its constructive means, its symbolic forms and its uses are firmly rooted in local traditions.

Performance evaluation of a miniature laser ablation time-of-flight mass spectrometer designed for in situ investigations in planetary space research

Key performance features of a miniature laser ablation time-of-flight mass spectrometer designed for in situ investigations of the chemical composition of planetary surfaces are presented. This mass spectrometer is well suited for elemental and isotopic analysis of raw solid materials with high sensitivity and high spatial resolution. In this study, ultraviolet laser radiation with irradiances suitable for ablation (< 1 GW/cm2) is used to achieve stable ion formation and low sample consumption. In comparison to our previous laser ablation studies at infrared wavelengths, several improvements to the experimental setup have been made, which allow accurate control over the experimental conditions and good reproducibility of measurements. Current performance evaluations indicate significant improvements to several instrumental figures of merit. Calibration of the mass scale is performed within a mass accuracy (Δm/m) in the range of 100 ppm, and a typical mass resolution (m/Δm) ~600 is achieved at the lead mass peaks. At lower laser irradiances, the mass resolution is better, about (m/Δm) ~900 for lead, and limited by the laser pulse duration of 3 ns. The effective dynamic range of the instrument was enhanced from about 6 decades determined in previous study up to more than 8 decades at present. Current studies show high sensitivity in detection of both metallic and non-metallic elements. Their abundance down to tens of ppb can be measured together with their isotopic patterns. Due to strict control of the experimental parameters, e.g. laser characteristics, ion-optical parameters and sample position, by computer control, measurements can be performed with high reproducibility. Copyright © 2012 John Wiley & Sons, Ltd.