Evaluation of non-contact sampling and detection of explosives using receiver operating characteristic curves

The growing need for fast sampling of explosives in high throughput areas has increased the demand for improved technology for the trace detection of illicit compounds. Detection of the volatiles associated with the presence of the illicit compounds offer a different approach for sensitive trace detection of these compounds without increasing the false positive alarm rate. This study evaluated the performance of non-contact sampling and detection systems using statistical analysis through the construction of Receiver Operating Characteristic (ROC) curves in real-world scenarios for the detection of volatiles in the headspace of smokeless powder, used as the model system for generalizing explosives detection. A novel sorbent coated disk coined planar solid phase microextraction (PSPME) was previously used for rapid, non-contact sampling of the headspace containers. The limits of detection for the PSPME coupled to IMS detection was determined to be 0.5-24 ng for vapor sampling of volatile chemical compounds associated with illicit compounds and demonstrated an extraction efficiency of three times greater than other commercially available substrates, retaining >50% of the analyte after 30 minutes sampling of an analyte spike in comparison to a non-detect for the unmodified filters. Both static and dynamic PSPME sampling was used coupled with two ion mobility spectrometer (IMS) detection systems in which 10-500 mg quantities of smokeless powders were detected within 5-10 minutes of static sampling and 1 minute of dynamic sampling time in 1-45 L closed systems, resulting in faster sampling and analysis times in comparison to conventional solid phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) analysis. Similar real-world scenarios were sampled in low and high clutter environments with zero false positive rates. Excellent PSPME-IMS detection of the volatile analytes were visualized from the ROC curves, resulting with areas under the curves (AUC) of 0.85-1.0 and 0.81-1.0 for portable and bench-top IMS systems, respectively. Construction of ROC curves were also developed for SPME-GC-MS resulting with AUC of 0.95-1.0, comparable with PSPME-IMS detection. The PSPME-IMS technique provides less false positive results for non-contact vapor sampling, cutting the cost and providing an effective sampling and detection needed in high-throughput scenarios, resulting in similar performance in comparison to well-established techniques with the added advantage of fast detection in the field.

Mary, a familiar homeless woman whose turf is 5th avenue and 14th street in NY

General note: Title and date provided by Bettye Lane.

Gas, water and volume characteristics during controlled degassing experiments on ODP Leg 164 PCS cores

A pressurized core with CH4 hydrate or dissolved CH4 should evolve gas volumes in a predictable manner as pressure is released over time at isothermal conditions. Incremental gas volumes were collected as pressure was released over time from 29 pressure core sampler (PCS) cores from Sites 994, 995, 996, and 997 on the Blake Ridge. Most of these cores were kept at or near 0ºC with an ice bath, and many of these cores yielded substantial quantities of CH4. Volume-pressure plots were constructed for 20 of these cores. Only five plots conform to expected volume and pressure changes for sediment cores with CH4 hydrate under initial pressure and temperature conditions. However, other evidence suggests that sediment in these five and at least five other PCS cores contained CH4 hydrate before core recovery and gas release. Detection of CH4 hydrate in a pressurized sediment core through volume-pressure relationships is complicated by two factors. First, significant quantities of CH4-poor borehole water fill the PCS and come into contact with the core. This leads to dilution of CH4 concentration in interstitial water and, in many cases, decomposition of CH4 hydrate before a degassing experiment begins. Second, degassing experiments were conducted after the PCS had equilibrated in an ice-water bath (0ºC). This temperature is significantly lower than in situ values in the sediment formation before core recovery. Our results and interpretations for PCS cores collected on Leg 164 imply that pressurized containers formerly used by the Deep Sea Drilling Project (DSDP) and currently used by ODP are not appropriately designed for direct detection of gas hydrate in sediment at in situ conditions through volume-pressure relationships.

CERAMICS IN BRITAIN (1840-90): MEANINGS AND METAPHORS

The intention of this thesis, “Ceramics in Britain (1840–90): Meanings and Metaphors” is to present new approaches for interpreting ceramics in nineteenth-century Britain by situating, problematizing, and contextualizing pottery and porcelain in the popular debates of the day within the methodologies of material culture, design, cultural and art histories. I ask how did ceramics—portable, functional, and often decorative objects—contribute to shaping modes of experiences? Crockery, tableware and blue-white-porcelain, admittedly largely mediated in texts and paintings, are at the centre of this research to examine how they imposed symbolism and influenced the engagement of their subjects beyond their intended meanings and functions. This thesis tracks a common rhetoric shared by writers and artists across genres and understood by readers and viewers: crockery in the cupboard, on the mantel, the table or the floor were popular motifs exemplifying class, gender, character, etiquette, and taste. This thesis also seeks to map ceramics’ relations with other objects and people depicted. Their meanings and metaphors changed, depending on their exchange with other objects in the room and who uses them. The conventions of representing ceramics dictated a particular grammar that writers and artists used, critiqued, discarded or personalized. The examination of ceramics mediated in text and image especially in comparison with extant objects invites a deeper probing of both material culture and artistic practice, which helps to situate the agency of the ceramic objects themselves. Also this thesis, in attempt to explore new methodological approaches for ceramic studies, examines the social life of the mid-Victorian relief-moulded “Minster” Jug in the Gardiner Museum in Toronto. The product originating in Staffordshire in 1843 and exported to the colonies holds significance due to its multiple life histories. Viewing the “Minster” through the lenses of curator, collector, consumer, and critic its layered lives unfold to reveal the protocols of museum praxis as well as important aspects of mid-nineteenth-century British society related to design reform, gender, imperialism and consumption patterns. This thesis contends that the British experienced ceramics in sometimes unexpected ways, unrelated to their original purpose, such as tools of violence or containers of solace, and transformative fantasy.

A Novel Methodology to Characterize the Constitutive Behaviour of Polyethylene terephthalate for the Stretch Blow Moulding process

The stretch blow moulding (SBM) process is the main method for the mass production of PET containers. And understanding the constitutive behaviour of PET during this process is critical for designing the optimum product and process. However due to its nonlinear viscoelastic behaviour, the behaviour of PET is highly sensitive to its thermomechanical history making the task of modelling its constitutive behaviour complex. This means that the constitutive model will be useful only if it is known to be valid under the actual conditions of interest to the SBM process. The aim of this work was to develop a new material characterization method providing new data for the deformation behaviour of PET relevant to the SBM process. In order to achieve this goal, a reliable and robust characterization method was developed based on an instrumented stretch rod and a digital image correlation system to determine the stress-strain relationship of material in deforming preforms during free stretch-blow tests. The effect of preform temperature and air mass flow rate on the deformation behaviour of PET was also investigated.

Free-stretch-blow Investigation of Poly(ethylene terephthalate) over a Large Process Window

This paper highlights for the first time a full comprehension of the deformation procedure during the injection stretch blow moulding (ISBM) process of poly(ethylene terephthalate) (PET) containers, namely thin-walled rigid bottles. The processes required to form PET bottles are complicated and extensive; any development in understanding the nature of material deformation can potentially improve the bottle optimisation process. Removing the bottle mould and performing free-stretch-blow (FSB) experiments revealed insight into the bottle forming characteristics at various preform temperatures and blowing rates. Process outputs cavity pressure and stretch-rod force were recorded using at instrumented stretch-rod and preform surface strain mapping was determined using a combination of a unique patterning procedure and high speed stereoscopic digital image correlation. The unprecedented experimental analysis reveals that the deformation behaviour varies considerably with contrasting process input parameters. Investigation into the effect on deformation mode, strain rate and final bottle shape provide a basis for full understanding of the process optimisation and therefore how the process inputs may aid development of the preferred optimised container.

Finite Element Simulations of stretch-blow moulding with experimental validation over a broad process window

Injection stretch blow moulding is a well-established method of forming thin-walled containers and has been extensively researched for numerous years. This paper is concerned with validating the finite element analysis of the free-stretch-blow process in an effort to progress the development of injection stretch blow moulding of poly(ethylene terephthalate). Extensive data was obtained experimentally over a wide process window accounting for material temperature and air flow rate, while capturing cavity pressure, stretch-rod reaction force and preform surface strain. This data was then used to assess the accuracy of the correlating FE simulation constructed using ABAQUS/Explicit solver and an appropriate viscoelastic material subroutine. Results reveal that the simulation is able to give good quantitative correlation for conditions where the deformation was predominantly equal biaxial whilst qualitative correlation was achievable when the mode of deformation was predominantly sequential biaxial. Overall the simulation was able to pick up the general trends of how the pressure, reaction force, strain rate and strain vary with the variation in preform temperature and air flow rate. The knowledge gained from these analyses provides insight into the mechanisms of bottle formation, subsequently improving the blow moulding simulation and allowing for reduction in future development costs.

Effect of the processing conditions on the microstructure and properties of rotational molded polyamide 11

Rotomolded containers for solvents and hydrocarbons require the use of high-permeability resins such as polyamide (PA). The published studies with this material are very scarce. In this work, a commercial grade of PA11 was rotational-molded using different processing temperatures and characterized with a range of techniques. The study aims at investigating the influence of the processing conditions on the microstructure and properties of molded parts. The results showed that the spherulitic morphology and the mechanical properties are affected by the processing temperature, the optimum processing range being between 220°C and 240°C. Overheating causes a decrease of the impact strength and a severe increase in the formation of pinholes at the outer surface due to polymer degradation and formation of volatile products. The thermo-oxidation reactions occurring at the inner surface of the samples result in the formation of products that absorb in the UV and visible light regions and cause the microhardness and the melt viscosity of the material to increase. The extent and severity of the degradation at the inner surface may be easily assessed by fluorescence microscopy. © 2008 Wiley Periodicals, Inc.

Modulare Logistiksysteme in der Prozessindustrie unter Einbeziehung von Industrie 4.0

Zur Gewährleistung einer kundenindividuellen, flexiblen Produktion, welche auch kleine Losegrößen kostengünstig produzieren kann, werden zukünftig Fabriken der Prozessindustrie nicht nur modular sondern darüber hinaus mobil sein. Zur Erreichung dieses Zieles werden neben Produktionselemente, auch sämtliche Logistikkomponenten in Containern zu Modulen zusammengefasst. Hierfür ist es notwendig Lager, aber auch komplexe Verpackungsmaschinen, zu konzipieren welche sich zusammen mit Produktionsmodulen, nach dem Plug-and-Produce-Prinzip, zu kompletten Produktionslinien verknüpfen lassen. Die Steuerung und Organisation erfolgt nach den Gedanken von Industrie 4.0.

Leistungsverfügbarkeit und Echtzeitfähigkeit in Systemen intelligenter Ladungsträger

In diesem Artikel werden Leistungsverfügbarkeit und Echtzeitfähigkeit am Beispiel eines Lagersystems für intelligente Behälter betrachtet. Es wird dabei die Echtzeitfähigkeit dieses Systems anhand einer realistischen Fallstudie in einem Stetigfördersystem analysiert. Anhand dieser Analyse wird ein Konzept für die gezielte Planung eines Lagersystems für eine spezifische Leistungsverfügbarkeit entworfen. Kernbestandteil ist ein Kommunikationsprotokoll, das die Reservierung von Fördermitteln mittels logischer Zeit erlaubt. Über eine veränderte Reservierungsstrategie kann ein geeigneter Dispositionszeitpunkt berechnet werden, der eine Termineinhaltung aller Aufträge garantiert.

Crystallization on the Mesoscale : Self-Assembly of Iron Oxide Nanocubes into Mesocrystals

Self-assembly of nanoparticles is a promising route to form complex, nanostructured materials with functional properties. Nanoparticle assemblies characterized by a crystallographic alignment of the nanoparticles on the atomic scale, i.e. mesocrystals, are commonly found in nature with outstanding functional and mechanical properties. This thesis aims to investigate and understand the formation mechanisms of mesocrystals formed by self-assembling iron oxide nanocubes. We have used the thermal decomposition method to synthesize monodisperse, oleate-capped iron oxide nanocubes with average edge lengths between 7 nm and 12 nm and studied the evaporation-induced self-assembly in dilute toluene-based nanocube dispersions. The influence of packing constraints on the alignment of the nanocubes in nanofluidic containers has been investigated with small and wide angle X-ray scattering (SAXS and WAXS, respectively). We found that the nanocubes preferentially orient one of their {100} faces with the confining channel wall and display mesocrystalline alignment irrespective of the channel widths.  We manipulated the solvent evaporation rate of drop-cast dispersions on fluorosilane-functionalized silica substrates in a custom-designed cell. The growth stages of the assembly process were investigated using light microscopy and quartz crystal microbalance with dissipation monitoring (QCM-D). We found that particle transport phenomena, e.g. the coffee ring effect and Marangoni flow, result in complex-shaped arrays near the three-phase contact line of a drying colloidal drop when the nitrogen flow rate is high. Diffusion-driven nanoparticle assembly into large mesocrystals with a well-defined morphology dominates at much lower nitrogen flow rates. Analysis of the time-resolved video microscopy data was used to quantify the mesocrystal growth and establish a particle diffusion-based, three-dimensional growth model. The dissipation obtained from the QCM-D signal reached its maximum value when the microscopy-observed lateral growth of the mesocrystals ceased, which we address to the fluid-like behavior of the mesocrystals and their weak binding to the substrate. Analysis of electron microscopy images and diffraction patterns showed that the formed arrays display significant nanoparticle ordering, regardless of the distinctive formation process.  We followed the two-stage formation mechanism of mesocrystals in levitating colloidal drops with real-time SAXS. Modelling of the SAXS data with the square-well potential together with calculations of van der Waals interactions suggests that the nanocubes initially form disordered clusters, which quickly transform into an ordered phase.

Toxicity of hexanic and methanolic fractions from copaifera reticulata ducke (Leguminosae – Caesalpinoidea) against Aedes aegypti Linnaeus (Diptera – Culicidae), in field assays

v. 45, n. 2, abr./jun. 2016.

Vehicle Distance Threshold for Quayside Operations of Container Terminals

Thesis (Master's)--University of Washington, 2016-08

Avaliação da anchoita (engraulis anchoita) salgada maturada acondicionada em atmosfera modificada

A anchoita foi capturada e acondicionada a bordo sob-resfriamento a 0°C com gelo em escamas. Após o recebimento, o pescado foi processado na forma salgado-maturado. Após a maturação foram processadas e embaladas em sacos de polietileno e armazenadas sob-refrigeração a 5°C durante 84 dias. As amostras foram divididas grupos: (1) sob pressão atmosfera normal, (2) vácuo, (3) atmosfera modificada com 50% CO2 + 20% O2 + 30% N2 e (4) 60% CO2 + 10% O2 + 30% N2, em embalagens de polietileno e aluminizadas, termo-seladas e armazenadas sob-refrigeração a 5°C. Os valores de textura tiveram uma redução de 2277,8 N (Kg.m/s2 ) para 821,90 N (Kg.m/s2 ) para o tratamento controle. A qualidade inicial do pescado atendeu aos padrões legais vigentes, apresentando ausência Salmonella sp e enumerações aceitáveis aos padrões de Staphylococcus coagulase positiva, Clostridium sulfito redutores, coliforme totais e a 45ºC. Com relação ao pH, houve diferenças significativas durante o tempo de processamento (p<0,05), o valor passou de 6,3 (início) para 6,4 (final). Com relação aos resultados correspondentes aos parâmetros L*, a* e b* (cor), em todos os tratamentos e ao longo do tempo de processamento (ambas as embalagens), ocorreram diferenças significativas (p<0,05). Os valores de L* variaram de 34,80 para 18,00 (controle) 23,00 (vácuo), 20,21 (T3) e 22,00 (T4) embalagens de polietileno. Nas embalagens de alumínio os valores de L* variaram de 34,00 para 25,00 (controle), 29,00(vácuo), 22,10 (T3) e 26,00 (T4).

Sistema integrado de localização de contentores de correio

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Informática e de Computadores