Natural hydraulic lime mortars with ceramic residues for masonry

9th International Masonry Conference 2014, 7-9 July, Universidade do Minho, Guimarães

Eco-efficient earthen plasters: The influence of the addition of natural fibers.

Clayish earth-based mortars are been recognized, all over the world, as eco-efficient products for plastering. Apart from being a product with low embodied energy when compared to other types of plasters, their application on the interior surface of walls may give a strong contribution for the health and comfort of inhabitants. As part of an ongoing research regarding earth-based plasters this work assesses the influence of the addition of two types of natural fibres – oat straw and typha fiber-wool – on the characteristics of plastering mortars made with a clayish earth. Mechanical and physical characteristics were tested, showing that addition of these fibers contribute to decrease linear drying shrinkage and thermal conductivity, as well as promoting the adhesion strength of plaster to the substrate. The improvement of mechanical resistance reveal to be dependent on the type of fiber added while the hygroscopic capacity of the plaster is maintained regardless of the fiber additions.

NHL 3.5 mortars with scrap tire rubber

The use of wastes and industrial by-products as building materials is an important issue in order to decrease costs with waste management and the embodied energy of building products. Scrap tire rubber has been studied as aggregate for cementitious materials. Natural hydraulic limes are natural binders with particular characteristics of both air and hydraulic binders. Their specifications became stricter with the last version of EN 459-1:2010. In this study scrap tire rubber was used as additional aggregate of mortars, based on NHL3.5 and natural sand. Different particle size fractions and proportions of scrap tire rubber were used: a mix obtained almost directly from industry (only after sieving for preparation of particle sizes similar to mortar aggregate) and separated fine, medium and coarse fractions; 0%, 18%, 36% and 54% weight of binder, corresponding to 2.5%, 5% and 7.5% weight of sand. The influence of the rubbers´ additions on the mortars´ fresh state, mechanical and physical performance is presented, namely by flow table consistency, water retention, fresh bulk density, dynamic elasticity modulus, flexural and compressive strength, open porosity and bulk density, capillary absorption, drying and thermal conductivity. The use of the rubber mix coming from the waste tire industry seems advantageous and may open possibilities for use as raw material by the mortars industry.

Caracterização da fase activa de catalisadores de Níquel suportados em α-Alumina, utilizando as reacções de desidrogenação e Hidrogenólise do Ciclohexano

A constante melhoria da eficiência energética dos processos industriais actuais é crucial para o contínuo desenvolvimento sustentável da espécie humana. O estudo das reacções de desidrogenação e hidrogenólise do ciclohexano, sobre catalisadores suportados, pode contribuir para um melhor entendimento acerca dos processos de formação e armazenamento de H2, uma das mais promissoras fontes de energia do futuro próximo, assim como para processos actuais tão importantes como a refinação ou o reforming catalítico do petróleo. Escolheu-se estudar as referidas reacções sobre catalisadores de Ni/α-Al2O3, preparados por três métodos distintos e submetidos a diferentes pré-tratamentos, de modo a realçar a dependência das reacções no que se refere às propriedades catalíticas. A maioria dos estudos anteriores sobre estas mesmas reacções recai sobre catalisadores com metais nobres, como a platina ou o paládio, bastante mais dispendiosos que o níquel para aplicações em larga escala. Os precursores e catalisadores previamente preparados foram submetidos à caracterização por diferentes técnicas: Termogravimetria (sob fluxo oxidativo e não oxidativo), Difracção de Raios-X e Quimissorção de H2. O estudo das reacções de desidrogenação e hidrogenólise do ciclohexano realizou-se recorrendo à análise por Cromatografia Gasosa, utilizando dois cromatógrafos distintos (HEWLETT PACKARD 5890 SERIES II, para GC, e 490 Micro GC Agilent, para Micro GC). Pôde concluir-se que o método de preparação dos catalisadores influenciou a actividade para ambas as reacções, assim como os diferentes pré-tratamentos aplicados. No geral, e na gama de temperaturas estudadas (entre 250 e 310º C), os catalisadores preparados pelo método com etilenodiamina evidenciaram maior actividade para a reacção de desidrogenação, sendo que os catalisadores preparados pelo método com etilenoglicol foram os mais activos para a reacção de hidrogenólise.

Al-doped ZnO ceramic sputtering targets based on nanocrystalline powders produced by emulsion detonation synthesis – deposition and application as a transparent conductive oxide material

Transparent conducting oxides (TCOs) have been largely used in the optoelectronic industry due to their singular combination of low electrical resistivity and high optical transmittance. They are usually deposited by magnetron sputtering systems being applied in several devices, specifically thin film solar cells (TFSCs). Sputtering targets are crucial components of the sputtering process, with many of the sputtered films properties dependent on the targets characteristics. The present thesis focuses on the development of high quality conductive Al-doped ZnO (AZO) ceramic sputtering targets based on nanostructured powders produced by emulsion detonation synthesis method (EDSM), and their application as a TCO. In this sense, the influence of several processing parameters was investigated from the targets raw-materials synthesis to the application of sputtered films in optoelectronic devices. The optimized manufactured AZO targets present a final density above 99 % with controlled grain size, an homogeneous microstructure with a well dispersed ZnAl2O4 spinel phase, and electrical resistivities of ~4 × 10-4 Ωcm independently on the Al-doping level among 0.5 and 2.0 wt. % Al2O3. Sintering conditions proved to have a great influence on the properties of the targets and their performance as a sputtering target. It was demonstrated that both deposition process and final properties of the films are related with the targets characteristics, which in turn depends on the initial powder properties. In parallel, the influence of several deposition parameters in the film´s properties sputtered from these targets was investigated. The sputtered AZO TCOs showed electrical properties at room temperature that are superior to simple oxides and comparable to a reference TCO – indium tin oxide (ITO), namely low electrical resistivity of 5.45 × 10-4 Ωcm, high carrier mobility (29.4 cm2V-1s-1), and high charge carrier concentration (3.97 × 1020 cm-3), and also average transmittance in the visible region > 80 %. These superior properties allowed their successful application in different optoelectronic devices.

Trading the changes of stock market index composition: Evidence from European markets

This paper studies the changes in European stock market indexes composition from 1995 to 2015. It was found that there are mixed price effects producing abnormal returns around the effective replacement of added and deleted stocks. The price pressure hypothesis seems to hold for added stocks in some indexes but not for deleted stocks as there is not a clear inversion of behaviour after the replacement. Finally, the building and back testing of a trading strategy aiming to capture some of those abnormal returns shows it yields a Sharpe Ratio of 1.4 and generates an annualised alpha of 11%.

Natural hydraulic lime (nhl3.5) mortars with scrap tire rubber

The use of wastes and industrial by-products as building materials is an important issue in order to decrease costs with waste management and the embodied energy of building products. In this study scrap tire rubber was used as additional aggregate of mortars based on natural hydraulic lime NHL 3.5 and natural sand. Different particle size fractions and proportions of scrap tire rubber were used: a mix obtained directly from industry and separated fine, medium and coarse fractions; 0 %, 18 %, 36 % and 54 % of the weight of binder, corresponding to 2.5 %, 5 % and 7.5 % of the weight of sand. As mortars based on NHL specifications became stricter with the current version of EN 459–1:2015, the influence of the rubber’s additions on the mortars’ fresh state, mechanical and physical performance is presented in this work: flow table consistency, water retention, dynamic elasticity modulus, flexural and compressive strength, open porosity and bulk density, capillary absorption, drying and thermal conductivity are studied. The use of the rubber mix coming from the waste tire industry seems advantageous and may open possibilities for use as raw material by the mortars industry.

Eco-efficient self-compacting concrete with reduced Portland cement content and high volume of fly ash and metakaolin

The eco-efficient, self-compacting concrete (SCC) production, containing low levels of cement in its formulation, shall contribute for the constructions' sustainability due to the decrease in Portland cement use, to the use of industrial residue, for beyond the minimization of the energy needed for its placement and compaction. In this context, the present paper intends to assess the viability of SCC production with low cement levels by determining the fresh and hardened properties of concrete containing high levels of fly ash (FA) and also metakaolin (MK). Hence, 6 different concrete formulations were produced and tested: two reference concretes made with 300 and 500 kg/m3 of cement; the others were produced in order to evaluate the effects of high replacement levels of cement. Cement replacement by FA of 60% and by 50% of FA plus 20% of MK were tested and the addition of hydrated lime in these two types of concrete were also studied. To evaluate the self-compacting ability slump flow test, T500, J-ring, V-funnel and L-box were performed. In the hardened state the compressive strength at 3, 7, 14, 21, 28 and 90 days of age was determined. The results showed that it is possible to produce low cement content SCC by replacing high levels of cement by mineral additions, meeting the rheological requirements for self-compacting, with moderate resistances from 25 to 30 MPa after 28 days.

Fertilization and cover crop effects on soil nitrogen and plant nutrition in a young guarana plantation

Fruit tree production is gaining an increasing importance in the central Amazon and elsewhere in the humid tropics, but very little is known about the nutrient dynamics in the soil-plant system. The present study quantified the effects of fertilization and cover cropping with a legume (Pueraria phaseoloides (Roxb.) Benth.) on soil nitrogen (N) dynamics and plant nutrition in a young guarana plantation (Paullinia cupana Kunth. (H.B. and K.) var. sorbilis (Mart.) Ducke) on a highly weathered Xanthic Ferralsol. Large subsoil nitrate (NO3-) accumulation at 0.3-3 m below the guarana plantation indicated N leaching from the topsoil. The NO3- contents to a depth of 2 m were 2.4 times greater between the trees than underneath unfertilized trees (P<0.05). The legume cover crop between the trees increased soil N availability as shown by elevated aerobic N mineralization and lower N immobilization in microbial biomass. The guarana N nutrition and yield did not benefit from the N input by biological fixation of atmospheric N2 by the legume cover (P>0.05). Even without a legume intercrop, large amounts of NO3- were found in the subsoil between unfertilized trees. Subsoil NO3- between the trees could be utilized, however, by fertilized guarana. This can be explained by a more vigorous growth of fertilized trees which had a larger nutrient demand and exploited a larger soil volume. With a legume cover crop, however, more mineral N was available at the topsoil which was leached into the subsoil and consequently accumulated at 0.3-3 m depth. Fertilizer additions of P and K were needed to increase subsoil NO3- use between trees.

The ceramic artifacts in archaeological black earth (terra preta) from Lower Amazon Region, Brazil: chemistry and geochemical evolution

This paper carried out a chemical investigation of archaeological ceramic artifacts found in archaeological sites with Black Earth (ABE) in the Lower Amazon Region at Cachoeira-Porteira, State of Pará, Brazil. The ceramic artifacts, mostly of daily use, belong to Konduri culture (from 900 to 400 years BP). They are constituted of SiO2, Al2O3, Fe2O3, Na2O and P2O5; SiO2 and Al2O3 together add up to 80 % and indicate influence of acid rocks, transformed into clay minerals basically kaolinite. The relative high contents of P2O5 (2.37 % in average) come out as (Al,Fe)-phosphate, an uncommon fact in primitive red ceramics, but found in some roman and egyptian archaeological sites. The contents of the trace elements are similar or below the Earth's crust average. This chemical composition (except P2O5) detaches saprolite material derived acid igneous rocks or sedimentary ones as the main raw material of the ceramics. The contents of K, Na and Ca represent the feldspars and rock fragments possibly introduced into saprolitic groundmass, indicated by mineralogical studies. The presence of cauixi and cariapé as well as quartz sand was confirmed by optical microscope, SEM analyses and by the high silica contents of ceramic fragments. Phosphorus was possibly incorporated into groundmass during cooking of foods, and ABE soil profile formation developed on yellow Latosols. The raw materials and its tempers (cauixi, or cariapé, feldspar, crushed rocks, old ceramic artifacts and quartz fragments) are found close to the sites and therefore and certainly came from them.

Mineralogia e geoquímica dos perfis sobre sedimentos neógenos e quaternários da bacia do Solimões na região de Coari - AM

O estudo do intemperismo das rochas é uma ferramenta indispensável para entender a evolução paleoambiental do Cenozóico na Amazônia. Com esse objetivo foram estudados seis perfis intempéricos desenvolvidos a partir da Formação Solimões e um perfil do Quaternário da várzea do rio Solimões, no centro-leste do estado do Amazonas. As informações obtidas permitiram determinar o grau de evolução intempérica na região, além das suas características estruturais, mineralógicas e químicas. Os perfis desenvolvidos sobre a Formação Solimões são constituídos, de baixo para cima, pelos horizontes saprolítico (C), mosqueado (B) e solo (A), enquanto o perfil sobre a sedimentação quaternária é estruturado nos horizontes saprolito (C) e solo (A). São argilo-arenosos a areno-argilosos, cinzentos, amarelados, avermelhados e esbranquiçados e compõem-se de quartzo, caulinita, muscovita, illita e esmectita. Segundo as suas características os perfis são divididos em dois grupos: 1) perfis 2, 3, 4 e 5: são areno-argilosos, tem altos teores de SiO2, Hg e Zr e estão associados unicamente à Formação Solimões; 2) perfis 1, 6 e 7: são pelíticos, têm maiores conteúdos em esmectita, illita, muscovita, Al2O3, álcalis e elementos-traço, especialmente de Ba, Co, Li, Ni, Sr, V, Y e Zn, e agrupam parte dos perfis sobre a Formação Solimões e o sedimento quaternário. A semelhança geoquímica entre este último e parte dos perfis sobre a Formação Solimões sugere que esta pode ser a fonte pelo menos de parte do material depositado na várzea. O conjunto das características demonstra que os horizontes dentro de cada perfil são muito semelhantes entre si e, portanto, pouco evoluídos, apesar do clima atual quente e chuvoso da região de Coari (2300 mm.ano-1) promover intensa lixiviação. Conseqüentemente, por serem derivados dos sedimentos mais jovens da Bacia do Solimões, e, portanto sob ação recente do intemperismo, pode-se afirmar que a unidade que deu origem aos perfis na Formação Solimões foi exposta no Quaternário e que estes se encontram em desequilíbrio com as condições agressivas de lixiviação do ambiente laterítico reinantes na Amazônia pelo menos desde o Paleógeno.

Thin films composed of gold nanoparticles dispersed in a dielectric matrix: the influence of the host matrix on the optical and mechanical responses

Gold nanoparticles were dispersed in two different dielectric matrices, TiO2 and Al2O3, using magnetron sputtering and a post-deposition annealing treatment. The main goal of the present work was to study how the two different host dielectric matrices, and the resulting microstructure evolution (including both the nanoparticles and the host matrix itself) promoted by thermal annealing, influenced the physical properties of the films. In particular, the structure and morphology of the nanocomposites were correlated with the optical response of the thin films, namely their localized surface plasmon resonance (LSPR) characteristics. Furthermore, and in order to scan the future application of the two thin film system in different types of sensors (namely biological ones), their functional behaviour (hardness and Young's modulus change) was also evaluated. Despite the similar Au concentrations in both matrices (~ 11 at.%), very different microstructural features were observed, which were found to depend strongly on the annealing temperature. The main structural differences included: (i) the early crystallization of the TiO2 host matrix, while the Al2O3 one remained amorphous up to 800 °C; (ii) different grain size evolution behaviours with the annealing temperature, namely an almost linear increase for the Au:TiO2 system (from 3 to 11 nm), and the approximately constant values observed in the Au:Al2O3 system (4–5 nm). The results from the nanoparticle size distributions were also found to be quite sensitive to the surrounding matrix, suggesting different mechanisms for the nanoparticle growth (particle migration and coalescence dominating in TiO2 and Ostwald ripening in Al2O3). These different clustering behaviours induced different transmittance-LSPR responses and a good mechanical stability, which opens the possibility for future use of these nanocomposite thin film systems in some envisaged applications (e.g. LSPR-biosensors).

Mineralogia e química dos sedimentos de fundo do médio e baixo Madeira e de seus principais tributários: Amazonas - Brasil

O objetivo deste trabalho foi investigar a variação composicional e mineralógica dos sedimentos de fundo transportados pelos grandes rios da Amazônia, com nascentes nos Andes provenientes de rochas cratônicas. O estudo foi realizado com base em análises granulométricas, mineralógicas e químicas, incluindo isótopos de Pb, no rio Madeira e seus tributários. O conjunto de dados mostra que os sedimentos de fundo do rio Madeira são granulométrica, mineralógica e quimicamente distintos de seus principais tributários. Os sedimentos do rio Madeira são mais arenosos; têm maior quantidade de quartzo; menor conteúdo de Al2O3, Fe2O3, K2O, MgO, Na2O, PF, TiO2, P2O5, MnO e elementos-traço; e a maturidade aumenta de montante para jusante. Dentre os sedimentos dos tributários, os rios Machado e secundariamente o rio Marmelos são os que mais se aproximam da composição dos sedimentos do rio Madeira, enquanto que o Jamari com sedimentos com maior proporção de TiO2, Zr, Y, Nb, Ga, Hf, U, Ta e ETR, é o mais distinto. Apesar do ambiente de intenso intemperismo e erosão, em condições tropicais úmidas, a que estão submetidas as rochas drenadas pela bacia do rio Madeira, os valores das razões Th/Co, Th/Pb, Th/Yb, Al/Pb, Zr/Co e a composição isotópica de Pb indicam fontes distintas para os sedimentos de fundo estudados. Os sedimentos do rio Madeira são provenientes, principalmente, de rochas máficas, enquanto que os sedimentos de seus tributários têm como fonte essencialmente rochas félsicas.

Topossequência de solos na transição campos naturais-floresta na região de Humaitá, Amazonas

O objetivo deste trabalho foi estudar as relações solo-relevo em uma topossequência de transição campo/floresta na região de Humaitá, AM. A área do estudo foi selecionada com base na representatividade regional e no grau de preservação do ambiente. O estudo foi realizado ao longo de um caminhamento que atravessou os diferentes pedoambientes, partindo do ambiente de campo natural até o ambiente de floresta. Esses pedoambientes foram identificados e delimitados conforme a curvatura do terreno, expressão dos padrões vegetacionais e características pedológicas. Foram abertas trincheiras nos diversos segmentos e os perfis foram caracterizados morfologicamente e coletados por horizonte. Foram realizadas análises físicas e químicas para caracterização e determinados SiO2, Al2O3 e Fe2O3 por ataque sulfúrico, óxidos de Fe "livres" com ditionito-citrato-bicarbonato e o ferro mal cristalizado com oxalato de amônio. Análises mineralógicas foram realizadas por difratometria de raios X. Os resultados sugerem que a variação dos solos na topossequência tem relação direta com a variação do relevo, que condiciona a drenagem e o nível do lençol freático.

The mineralogy and chemistry of the German and Portuguese tiles used to face a historic building in the Amazon region and their natural susceptibility to tropical weathering

During the 19th century, the most prominent buildings of the city of Belém were faced entirely with tiles manufactured in Portugal and Germany, which now exhibit distinct degrees of degradation. The Pinho mansion is one of the most important of these buildings and was selected for the investigation of the action of the tropical Amazonian climate on the degradation of the tiles. To achieve this objective, the tiles were mapped for organic and inorganic degradation, and samples were collected for analysis. The minerals were determined by XRD, the chemical composition by classical wet methods and SEM/EDS, and the microorganisms under the microscope. The results show that the German and Portuguese tiles are quite different in their composition. While both ceramic bodies are composed of SiO2 and Al2O3, CaO was found only in the Portuguese tile. The low Na2O and K2O contents indicate the addition of materials to reduce the fusion temperature. SiO2 and PbO are the main constituents of the glaze, with CoO and FeO being added as pigment. The ceramic body of the German tiles is constituted of quartz, mullite, and cristobalite, in contrast with the Portuguese tiles, which are made of quartz, gehlenite, diopside, calcite, and feldspars. The glazes are XRD-amorphous. The chemical and mineralogical differences between the German and Portuguese tiles indicate that they were produced from different raw materials under distinct thermal processes. The most prominent weathering-related modifications are the thin layers (German tiles), oxidation stains, dark stains, the detachment of the tile (Portuguese tiles), loss of the glaze and powdering of the ceramic body (Portuguese tiles) through the establishment of Cyanophyta and Bacillariophyta.. The distinct degradation patterns of the tiles exposed to the tropical Amazon climate are a consequence of their distinct mineralogy and chemistry.