Influência da adição de cálcio nas propriedades de pastas geopoliméricas destinadas a cimentação de poços de petróleo

Nowadays, the search for new technologies that are able to follow the upcoming challenges in oil industry is a constant. Always trying properties improvements of the used materials, looking for the best performance and greater life time. Besides the search for technologies that show an improvement of performance, the search for materials environmentally correct along the whole production process. In Oil well cementing, this search for new technologies passes through the development of slurry systems that support these requests and that are also environmentally friendly. In this context, the use of geopolymer slurries is a great alternative route to cementing oil wells. Besides having good properties, comparable to Portland cement slurries, this alternative material releases much less CO2 gas in the production of their root materials when compared the production of Portland cement, which releases tons of CO2. In order to improve the properties of geopolymer slurries has been added Calcium Oxide, as observed in other studies that slurries where the Calcium is present the values of compressive strength is greater. The addition has been realized based in the CaO/SiO2 molar ratio of 0.05, 0.10 and 0.15. Have been performed compressive strength tests, thickening time, rheology and fliud loss control test of the slurries, following NBR 9831, as well as the physical chemical characterization of XRD, SEM and TG. Has been observed in most of the tests the slurries follow a tendency until the ratio of 0.10, which inverses in the ratio 0.15. This behavior can be explained by two phenomena that occur simultaneously, the first one is the break of the polymer chains and a consequent increase in molucules mobility, which prevails until the ratio of 0.1, and the second is possible approach of the chains due to the capacity of the calcium ions stabilize the charges of two different aluminum. There is only one linearity in the mechanical behavior that can be attributed to the appereance of the C-S-H phase. Based on this, it is concluded that the phenomenon of breaking the polymer chains predominates until the ratio of 0.1, causing an increase of the filtrate volume, lower rheological parameters and increasing thickening time. From the ratio of 0.15 the approach of the chains predominates, and the behavior is reversed

Utilização de nanosílica como aditivo estendedor para pastas cimentantes de baixa densidade destinadas à cimentação de poços petrolíferos

Cementing operations are conducted at different times of the well s life and they have high importance, because the functions are fundamental to keep good properties during a long life of the well, such as, maintain the mechanical stability of the well, to promote the isolation hydraulic and support the tubing. In some situations, the rocky zones have low fractures pressures and require the use of lightweight slurries to prevent the hydrostatic pressure in the formation is greater than the pressure of fracture. There are three ways to reduce the density of cement slurries: exterders water additives, microspheres and foamed slurries. The most used extender water additive is sodium bentonite, which is a clay with a good capacity of water absorption and expansion of its volume, the main disadvantage of this additive is the reduction of the strength. Currently, the use of nanoscale particles has received special attention, mainly because they get new functionalities. Following this trend, this paper aims to use a colloidal solution of nano-silica as an exterders water additives for use in oil wells. Slurries were designed with fixed 13lb/gal density and concentration of nano silica 0.1 gpc; 0.4 gpc; 0.7 and 1gpc, the influence of nano-silica was studied at these levels in isolation and combined varying concentrations of CaCl2,. Tests including rheology, stability, strength, thickening time, porosity and permeability. Besides the API tests, microstructural characterizations were performed after 28 days of the slurries, X-ray diffraction (XRD) and scanning electron microscopy (SEM)

Adição de resíduo cerâmico em pastas geopoliméricas para cimentação de poços de petróleo

The development of activities the of oil and gas sector have promoted the search for suitable materials for cementing oil wells. In the state of the Rio Grande do Norte, the integrity of the cement sheath tends to be impaired during steam injection, a procedure necessary to increase oil recovery in reservoirs with low-viscosity oil. The geopolymer is a material that can be used as alternative cement, since it has been used in the production of fire-resistant components, building structures, and for the control of toxic or radioactive residues. Geopolymers result from condensation polymer alkali aluminosilicates and silicates resulting three-dimensional polymeric structures. They are produced in a manner different from that of Portland cement, which is made an activating solution that is mixed with geopolymer precursor. Among the few works studied allowed us to conclude that the pastes prepared with metakaolin as precursor showed better performance of its properties. Several studies show the addition of waste clay as a means of reducing cost and improving end of the folder properties. On this basis, the goal is to study the influence of the addition of ceramic waste in geopolymer paste. To develop the study of rheology tests were carried out, filtered, thickening time, compressive strength, free water, specific gravity and permeability, according to the American Pretoleum Institute (API). The results for all formulations studied show that the folders have high mechanical strength to a light paste; low filtrate volume, absence of free water, very low permeability, slurry, consistent with a light paste, and thickening time low that can be corrected with the use of a retardant handle. For morphological characterization, microstructural, physical, chemical and thermal tests were carried out by XRD, MEV, DTA, TG, FTIR. In the trial of XRD, it was found that geopolymer is an amorphous material, with a peak of crystalline kaolinite. In tests of TG / DTA, revealed the presence of a significant event, which represents the mass loss related to water, and also observed the reduction of weight loss by increasing the concentration of ceramic waste. In the trial of MEV, we found a uniform matrix without the presence of other phases. In the trial of FT-IR, we observed the presence of the band related to water. From all results it was determined that the optimum concentration range of use is between 2.5 and 5% of waste ceramic

Influência da vermiculita expandida na formulação de pastas leves para evitar a migração de gás em cimentação de poços petrolíferos

The gas migration during the cementing of wells is one of the main problems of oil wells engineering. Its occurrence can cause severe problems since shortly to loss of control of the well after cementation. Recently, 20/04/2010 In an accident of major proportions in the Gulf of Mexico, among other factors, faulty cementing operation provided the gas migration, causing the accident, in which 11 people died and 17 were injured occurred. Besides the serious consequences that can be caused by gas migration, remediation of the problem, which is made by injecting cement in damaged areas, usually involves additional costs and is not always effective. Therefore, preventing gas migration to be preferred. Some methods are used to prevent the migration of the pressurized gas as the annular space, application of pressure pulses, reducing the height of the cement column compressible cement pastes of low permeability, pastes and to control free filtered water, and binders of thixotropic cement expandable and flexible. Thus, the cement pastes used to prevent gas migration must meet the maximum these methods. Thus, this study aimed to formulate a cement paste to prevent gas migration, using the expanded vermiculite, and evaluate the behavior of the folder trials necessary for use in oil wells. Free water content, rheological properties, compressive strength, loss of liquid phase sedimentation of solids, specific weight, thickening time and gas migration: The following tests were performed. The results show that meets the specifications paste formulated for use in oil wells and the use of expanded vermiculite contribute to the absorption of free water, thixotropy and low density. The absorption of free water is proven to result in zero percentage test free water content, thixotropy is observed with the high value of the initial gel strength (Gi) in testing rheological properties and low density is proven in test weight specific

Aditivação de pastas geopoliméricas com tetraborato de sódio e látex não iônico para cimentação de Poços de Petróleo

The development of activities in the oil and gas sector has been promoting the search for materials more adequate to oilwell cementing operation. In the state of Rio Grande do Norte, the cement sheath integrity tend to fail during steam injection operation which is necessary to increase oil recovery in reservoir with heavy oil. Geopolymer is a material that can be used as alternative cement. It has been used in manufacturing of fireproof compounds, construction of structures and for controlling of toxic or radioactive waste. Latex is widely used in Portland cement slurries and its characteristic is the increase of compressive strength of cement slurries. Sodium Tetraborate is used in dental cement as a retarder. The addition of this additive aim to improve the geopolymeric slurries properties for oilwell cementing operation. The slurries studied are constituted of metakaolinite, potassium silicate, potassium hydroxide, non-ionic latex and sodium tetraborate. The properties evaluated were: viscosity, compressive strength, thickening time, density, fluid loss control, at ambient temperature (27 ºC) and at cement specification temperature. The tests were carried out in accordance to the practical recommendations of the norm API RP 10B. The slurries with sodium tetraborate did not change either their rheological properties or their mechanical properties or their density in relation the slurry with no additive. The increase of the concentration of sodium tetraborate increased the water loss at both temperatures studied. The best result obtained with the addition of sodium tetraborate was thickening time, which was tripled. The addition of latex in the slurries studied diminished their rheological properties and their density, however, at ambient temperature, it increased their compressive strength and it functioned as an accelerator. The increase of latex concentration increased the presence of water and then diminished the density of the slurries and increased the water loss. From the results obtained, it was concluded that sodium tetraborate and non-ionic latex are promising additives for geopolymer slurries to be used in oilwell cementing operation

Estudo da formulação de pré-misturas secas para a cimentação de poços em terra

An economical solution for cementing oil wells is the use of pre-prepared dry mixtures containing cement and additives. The mixtures may be formulated, prepared and transported to the well where is added water to be pumped.Using this method, becomes dispensable to prepare the cement mixes containing additives in the cementing operation, reducing the possibility of error. In this way, the aim of this work is to study formulations of cement slurries containing solid additives for primary cementing of oil wells onshore for typical depths of 400, 800 and 1,200 meters. The formulations are comprised of Special Class Portland cement, mineral additions and solids chemical additives.The formulated mixtures have density of 1.67 g / cm ³ (14.0 lb / gal). Their optimization were made through the analysis of the rheological parameters, fluid loss results, free water, thickening time, stability test and mechanical properties.The results showed that mixtures are in conformity the specifications for cementing oil wells onshore studied depths

Influência da adição de cinza do bagaço de cana calcinada em sistemas de pastas para cimentação de poços petrolíferos

Cementing operation is one of the most important stages in the oil well drilling processes and has main function to form hydraulic seal between the various permeable zones traversed by the well. However, several problems may occur with the cement sheath, either during primary cementing or during the well production period. Cements low resistance can cause fissures in the cement sheath and compromise the mechanical integrity of the annular, resulting in contamination of groundwater and producing zones. Several researches show that biomass ash, in particular, those generated by the sugarcane industry have pozzolanic activity and can be added in the composition of the cementing slurries in diverse applications, providing improvements in mechanical properties, revenue and cement durability. Due to the importance of a low cost additive that increases the mechanical properties in a well cementing operations, this study aimed to potentiate the use of sugarcane bagasse ash as pozzolanic material, evaluate the mechanisms of action of this one on cement pastes properties and apply this material in systems slurries aimed to cementing a well with 800 m depth and geothermal gradient of 1.7 °F/100 ft, as much primary cementing operations as squeeze. To do this, the ash beneficiation methods were realized through the processes of grinding, sifting and reburning (calcination) and then characterization by X-ray fluorescence, XRD, TG / DTG, specific surface area, particle size distribution by laser diffraction and mass specific. Moreover, the ash pozzolanic activity added to the cement at concentrations of 0%, 20% and 40% BWOC was evaluated by pozzolanic activity index with lime and with Portland cement. The evaluation of the pozzolanic activity by XRD, TG / DTG and compressive strength confirmed the ash reactivity and indicated that the addition of 20% in the composition of cement slurries produces improvement 34% in the mechanical properties of the slurry cured. Cement slurries properties evaluated by rheological measurements, fluid loss, free fluid, slurry sedimentation, thickening time and sonic strength (UCA) were satisfactory and showed the viability of using the sugarcane ash in cement slurries composition for well cementing

Étude paléopathologique préliminaire à travers l'analyse macroscopique et scanographique : exemple du cimetière St. Matthew, ville de Québec (1771-1860)

Sachant que plusieurs maladies entrainent des lésions qui ne sont pas toujours observables à l’oeil, cette étude préliminaire en paléopathologie humaine utilise une approche complémentaire issue de l’imagerie médicale, le ct-scan, afin de fournir des diagnostics plus précis. L’objectif est donc de tester ici l’efficacité et les limites de l’analyse scanographique durant l’analyse de spécimens archéologiques. Un échantillon de 55 individus a été sélectionné à partir de la collection ostéologique provenant du cimetière protestant St. Matthew (ville de Québec, 1771 – 1860). Une analyse macroscopique et scanographique complète a alors été effectuée sur chaque squelette. Les observations macroscopiques ont consisté à enregistrer une dizaine de critères standardisés par la littérature de référence en lien avec des manifestations anormales à la surface du squelette. Les ct-scans ont été réalisés à l’Institut National de la Recherche Scientifique de la Ville de Québec avec un tomodensitomètre Somatom de Siemens (définition AS+ 128). Les données scanographiques ont permis d’enregistrer une série de critères complémentaires sur la structure interne de l’os (amincissement/épaississement de la corticale, variation de densité, etc.) Selon la méthode du diagnostic différentiel, des hypothèses ou diagnostics ont été proposés. Ils sont principalement basés sur les critères diagnostiques mentionnés dans les manuels de référence en paléopathologie, mais aussi à l’aide de la littérature clinique et l’expertise de médecins. Les résultats présentés ici supportent que: 1) Dans 43% des cas, les données scanographiques ont apporté des informations essentielles dans la diagnose pathologique. Cette tendance se confirme en fonction de certaines maladies, mais pas d’autres, car certains diagnostics ne peuvent se faire sans la présence de tissus mous. 2) La distribution spatiale de la plupart des lésions varie selon les régions anatomiques, aussi bien en macroscopie qu’en scanographie. 3) Certains types de maladie semblent associés à l’âge et au sexe, ce qui est conforté par la littérature. 4) Cette recherche démontre aussi que le processus de diagnose nécessite, dans 38% des cas, une analyse complémentaire (ex. histologie, scintigraphie, radiographie) pour préciser le diagnostic final.

Étude paléopathologique préliminaire à travers l'analyse macroscopique et scanographique : exemple du cimetière St. Matthew, ville de Québec (1771-1860)

Sachant que plusieurs maladies entrainent des lésions qui ne sont pas toujours observables à l’oeil, cette étude préliminaire en paléopathologie humaine utilise une approche complémentaire issue de l’imagerie médicale, le ct-scan, afin de fournir des diagnostics plus précis. L’objectif est donc de tester ici l’efficacité et les limites de l’analyse scanographique durant l’analyse de spécimens archéologiques. Un échantillon de 55 individus a été sélectionné à partir de la collection ostéologique provenant du cimetière protestant St. Matthew (ville de Québec, 1771 – 1860). Une analyse macroscopique et scanographique complète a alors été effectuée sur chaque squelette. Les observations macroscopiques ont consisté à enregistrer une dizaine de critères standardisés par la littérature de référence en lien avec des manifestations anormales à la surface du squelette. Les ct-scans ont été réalisés à l’Institut National de la Recherche Scientifique de la Ville de Québec avec un tomodensitomètre Somatom de Siemens (définition AS+ 128). Les données scanographiques ont permis d’enregistrer une série de critères complémentaires sur la structure interne de l’os (amincissement/épaississement de la corticale, variation de densité, etc.) Selon la méthode du diagnostic différentiel, des hypothèses ou diagnostics ont été proposés. Ils sont principalement basés sur les critères diagnostiques mentionnés dans les manuels de référence en paléopathologie, mais aussi à l’aide de la littérature clinique et l’expertise de médecins. Les résultats présentés ici supportent que: 1) Dans 43% des cas, les données scanographiques ont apporté des informations essentielles dans la diagnose pathologique. Cette tendance se confirme en fonction de certaines maladies, mais pas d’autres, car certains diagnostics ne peuvent se faire sans la présence de tissus mous. 2) La distribution spatiale de la plupart des lésions varie selon les régions anatomiques, aussi bien en macroscopie qu’en scanographie. 3) Certains types de maladie semblent associés à l’âge et au sexe, ce qui est conforté par la littérature. 4) Cette recherche démontre aussi que le processus de diagnose nécessite, dans 38% des cas, une analyse complémentaire (ex. histologie, scintigraphie, radiographie) pour préciser le diagnostic final.

Factores asociados a la mortalidad en el síndrome de Sjögren

Antecedentes: El síndrome de Sjögren (SS) es una patología crónica, autoinmune, de características multifactoriales en su etiología. También es conocida como una epitelitis autoinmune, caracterizada por síntomas secos como xeroftalmia y xerostomía, pero que también puede tener compromiso sistémico, dado por manifestaciones extra-glandulares. En la actualidad es poco reconocida como tal, y por lo tanto, la tasa de sobrevida en estos pacientes se encuentra disminuida pero poco tenida en cuenta a la hora de la valoración de ellos. Este trabajo describe la evidencia encontrada acerca de las causas de mortalidad y sus factores asociados luego de realizar una revisión sistemática de la literatura. Objetivos: El objetivo de este estudio fue reunir de forma exhaustiva y sistemática toda la evidencia empírica, publicada o no, que cumpla los criterios de búsqueda y elegibilidad sobre factores asociados al incremento de la mortalidad o disminución en la sobrevida de los pacientes con diagnóstico de SS. Métodos: Se realizó una revisión sistemática de la literatura mediante una búsqueda exhaustiva de todos los estudios publicados en las bases de datos electrónicas preestablecidas, hasta abril de 2015, con el fin de determinar las causas más frecuentes de mortalidad en pacientes con SS y los factores asociados a ella. Resultados: Se encontraron 4,654 resultados que coincidían con los criterios de búsqueda establecidos; de estos, 33 cumplieron con los criterios de inclusión y se distribuyeron de la siguiente forma: el 66.6% (22/33) correspondieron a estudios de corte cohorte, 30.3% (10/33) a estudios de corte transversal y el 3.03% (1/33) a estudios casos y controles. Se obtuvieron resultados en cuanto a frecuencias de mortalidad, razón estandarizada de mortalidad, tasas de supervivencia, causas más frecuentes de mortalidad y sus factores asociados. Conclusiones: La mortalidad reportada en los diferentes estudios fue entre el 1.2% hasta el 30%. Aquellos estudios que reportaron una tasa de mortalidad inferior al 5%, tuvieron un tiempo de seguimiento menor 8 años [1,7,33,60,64,86]. La mayoría de los casos sigue un curso relativamente estable, pero hay un porcentaje importante que presenta otras manifestaciones sistémicas con mayor frecuencia de complicaciones durante la evolución del SS. Por tanto, son los que requieren un seguimiento más estrecho, debido a una mayor necesidad de tratamiento sistémico y al mayor riesgo de ingreso hospitalario y de mortalidad, especialmente por el desarrollo de procesos linfoproliferativos B. La presencia de factores pronósticos en el paciente con SS obligará a realizar un seguimiento clínico e inmunológico mucho más estrecho, lo cual permitirá identificar lo antes posible las complicaciones que puedan aparecer e instaurar las correspondientes medidas terapéuticas, para aumentar las tasas de supervivencia.

Specific shear-dependent viscoelastic third-grade fluid model

A specific modified constitutive equation for a third-grade fluid is proposed so that the model be suitable for applications where shear-thinning or shear-thickening may occur. For that, we use the Cosserat theory approach reducing the exact three-dimensional equations to a system depending only on time and on a single spatial variable. This one-dimensional system is obtained by integrating the linear momentum equation over the cross-section of the tube, taking a velocity field approximation provided by the Cosserat theory. From this reduced system, we obtain the unsteady equations for the wall shear stress and mean pressure gradient depending on the volume flow rate, Womersley number, viscoelastic coefficient and flow index over a finite section of the tube geometry with constant circular cross-section.

Extensional orogenic collapse captured by strike-slip tectonics:

The late Paleozoic collision between Gondwana and Laurussia resulted in the polyphase deformation and magmatism that characterizes the Iberian Massif of the Variscan orogen. In the Central Iberian Zone, initial con- tinental thickening (D1; folding and thrusting) was followed by extensional orogenic collapse (D2) responsible for the exhumation of high-grade rocks coeval to the emplacement of granitoids. This study presents a tectonometamorphic analysis of the Trancoso-Pinhel region (Central Iberian Zone) to ex- plain the processes in place during the transition froman extension-dominated state (D2) to a compression-dom- inated one (D3).Wereveal the existence of low-dipping D2 extensional structures later affected by several pulses of subhorizontal shortening, each of them typified by upright folds and strike-slip shearing (D3, D4 and D5, as identified by superimposition of structures). The D2 Pinhel extensional shear zone separates a low-grade domain from an underlying high-grade domain, and it contributed to the thermal reequilibration of the orogen by facil- itating heat advection from lower parts of the crust, crustal thinning, decompression melting, and magma intru- sion. Progressive lessening of the gravitational disequilibrium carried out by this D2 shear zone led to a switch from subhorizontal extension to compression and the eventual cessation and capture of the Pinhel shear zone by strike-slip tectonics during renewed crustal shortening. High-grade domains of the Pinhel shear zone were folded together with low-grade domains to define the current upright folded structure of the Trancoso-Pinhel re- gion, the D3 Tamames-Marofa-Sátão synform. Newdating of syn-orogenic granitoids (SHRIMP U\\Pb zircon dat- ing) intruding the Pinhel shear zone, together with the already published ages of early extensional fabrics constrain the functioning of this shear zone to ca. 331–311 Ma, with maximum tectonomagmatic activity at ca. 321–317 Ma. The capture and apparent cessation of movement of the Pinhel shear zone occurred at ca. 317– 311 Ma.

Unraveling the pathophysiological mechanisms of visceral pain in the murine model of Fabry disease

Fabry disease (FD) is an X‐linked inherited, lysosomal storage disorder characterized by a deficient activity of the enzyme α-Galactosidase A (α-Gal A). This deficiency causes an accumulation of globotriaosylceramide 3 (Gb3), in nearly all organs. Gastrointestinal (GI) symptoms are among the earliest and most frequent symptoms of FD. It has been hypothesized that Gb3 accumulation is the leading cause of these, but their pathophysiology is complex and still poorly understood. Here, we aim at understanding the molecular mechanisms underpinning the GI symptoms of FD. For this purpose, we used the α‐Gal A (-/0) male mouse, a murine model of FD, to characterize morphological and molecular features of the colon tract. Our results show that α‐Gal A (-/0) mice display a thickening of the muscular layer due to a hypertrophic state of myenteric plexus ganglia, caused by an accumulation of Gb3 in neurons. Also, α-Gal A (-/0) mice present a decreased density of mucosal nerve fibres. Furthermore, α-Gal A (-/0) mice presented visceral hyperalgesia, by showing greater visceromotor response (VMR) values and obtaining higher abdominal withdrawal reflex (AWR) scores, following colorectal distension (CRD). Subsequently, the immunoreactivity of the pain-related ion channels TRPV1, TRPV4, TRPA1 and TRPM8 was detected at level of myenteric and submucosal plexus ganglia of both the genotypes. Further studies are required to assess differences of expression between α-Gal A (-/0) and control mice. Finally, we optimized the protocols to obtain three types of primary cultures from mouse intestine to be tested electrophysiologically: a mixed culture containing neurons and glia, an enriched culture of neurons, and one of glia. In summary, we revealed alterations that are likely to be part of the pathophysiological causes of FD GI symptoms. Therefore, together with further studies, this work could help identify new therapeutic targets for the treatment of visceral pain in FD.