Effect of La2O3 on microstructure and transmittance of transparent alumina ceramics

Optically transparent alumina ceramics were fabricated by conventional process and sintered without pressure in H-2 atmosphere. The results indicate that relative densities of alumina specimens increase to theoretical densities (T. D.) with increasing content of La2O3. With increasing holding time during sintering, much less pores and larger grains were found in the sintered alumina samples. Higher transmittance was achieved in alumina codoped with MgO and La2O3 as compared with that doped with MgO only. The total-transmittance of alumina sample is up to 86% at a wavelength range of 300 - 800 nm.

Yb：YAG透明陶瓷的制备和激光输出

制备了高质量的Yb：YAG透明陶瓷．Yb：YAG透明陶瓷的晶粒尺寸为10μm左右且分布均匀，晶界处和晶粒中没有杂质、气孔的存在．Yb：YAG样品中所有元素分布均匀，不同的晶粒间，晶粒和晶界间成分是一致的，没有出现成分的偏析．4mm厚样品的透过率为80％．LD泵浦获得了波长为1030nm，最大功率为268mW的连续激光输出．

Diode-pumped room-temperature continuous wave Tm3+ doped Lu2SiO5 laser

We report on room temperature laser actions of a novel thulium-doped crystal Tm center dot Lu2SiO5 (LSO) under diode pumping. An optical optical conversion efficiency of 12% and a slope efficiency of 21% were obtained with the maximum continuous wave (CW) output power of 0.67 W. The emission wavelengths of Tm LSO laser were centered at 2058.4 nm with bandwidth of similar to 13.6 nm.

Continuous-wave and passively mode-locked Yb : GYSO lasers pumped by diode lasers

We report both continuous-wave and passively mode-locked laser actions in a Yb3+-doped gadolinium yttrium oxyorthosilicate Yb:GdySiO(5) (Yb:GYSO) crystal. Continuous-wave (CW) laser operations were compared under different pump conditions with high-power diodes of different wavelengths and fiber cores. CW mode-locking was obtained with a semiconductor saturable absorber mirror.

Continuous-wave and Q-switched operation of a resonantly pumped Ho:YAlO3 laser

We demonstrated continuous-wave ( CW) and Q-switched operation of a room-temperature Ho: YAlO3 laser that is resonantly end-pumped by a diode-pumped Tm: YLF laser at 1.91 mu m. The CW Ho: YAlO3 laser generated 5.5 W of linearly polarized (E parallel to c) output at 2118 nm with beam quality factor of M-2 approximate to 1.1 for an incident pump power of 13.8 W, corresponding to optical-to-optical conversion efficiency of 40%. Up to 1-mJ energy per pulse at pulse repetition frequency (PRF) of 5 kHz, and the maximum average power of 5.3-W with FWHM pulse duration of 30.5 ns at 20 kHz were achieved in Q-switched mode. (C) 2008 Optical Society of America.

Diode-pumped continuous wave and Q-switched operation of a c-cut Tm,Ho:YAlO3 laser

We report on a diode-pumped, cryogenic and room temperature operation of a Tm,Ho:YAlO3 (c-cut) laser. In a temperature of 77 K, an optical-optical conversion efficiency of 27% and a slope efficiency of 29% were achieved with the maximum continuous-wave (CW) output power of 5.0 W at 2.13 mu m. Acousto-optic switched operation was performed at pulse repetition frequency (PRF) from 1 kHz to 10 kHz, the highest pulse energy of 3.3 mJ in a pulse duration of 40 ns was obtained. In room temperature (RT), the maximum CW power of Tm,Ho:YAlO3 laser was 160 mW with a slope efficiency of 11% corresponding to the absorbed pump power. (C) 2008 Optical Society of America.

An investigation into the potential losses of fish on the filter plates at the Hodder Water Treatment Works Stocks Reservoir

Stocks Reservoir is situated amidst the Forest of Bowland in the upper reaches of the old river valley of the Hodder. The reservoir was built in 1927 for the Fylde Water Board who primarily supplied water to Blackpool. The objective of this study is to assess the degree and likelihood of fish ingress onto the fish plates at the present and proposed stocking densities. An additional aim is to evaluate the operational implications, and if necessary suggest methods of alleviating the problem. Three spheres of study have been undertaken to achieve these objectives, these being: 1. To selectively stock the reservoir and monitor the angling club catches in order to assess the total population, relating it to fish plate losses and proposed stocking densities. 2. To monitor the fish taken from the fish plates and assess the reasons for their ingress. 3. To study the draw off tower and fish plates, and suggest ways of ameliorating or halting the loss of fish and consequent operational problems.