Hydrocarbon oxidation and three-way catalytic activity on a single step directly coated cordierite monolith: High catalytic activity of Ce0.98Pd0.02O2−δ

Catalytic activity of cordierite honeycomb by a completely new coating method for the oxidation of major hydrocarbons in exhaust gas is reported here. The new coating process consists of (a) dipping and growing γ-Al2O3 on cordierite by combustion of monolith dipped in the aqueous solution of Al(NO3)3 and oxalyldihydrazide (ODH) (or glycine) at 600 °C and active catalyst phase Ce0.98Pd0.02O2−δ on γ-Al2O3-coated cordierite again by combustion of monolith dipped in the aqueous solution of ceric ammonium nitrate, ODH and 1.2 × 10−3 M PdCl2 solution at 500 °C. Weight of active catalyst can be varied from 0.02 wt% to 2 wt% which is sufficient but can be loaded even up to 12 wt% by repeating dip dry combustion. Adhesion of catalyst to cordierite surface is via oxide growth, which is very strong. ‘HC’ oxidation over the monolith catalyst is carried out with a mixture having the composition, 470 ppm of both propene and propane and 870 ppm of both ethylene and acetylene with the varying amount of O2. Three-way catalytic test is done by putting hydrocarbon mixture along with CO (10 000 ppm), NO (2000 ppm) and O2 (15 000 ppm). Below 350 °C full conversion is achieved. In this method, handling of nano-material powder is avoided.

ZnO nanocrystalline thin films: a correlation of microstructural, optoelectronic properties

The compositional, structural, microstructural, dc electrical conductivity and optical properties of undoped zinc oxide films prepared by the sol-gel process using a spin-coating technique were investigated. The ZnO films were obtained by 5 cycle spin-coated and dried zinc oxide films followed by annealing in air at 600 A degrees C. The films deposited on the platinum coated silicon substrate were crystallized in a hexagonal wurtzite form. The energy-dispersive X-ray (EDX) spectrometry shows Zn and O elements in the products with an approximate molar ratio. TEM image of ZnO thin film shows that a grain of about 60-80 nm in size is really an aggregate of many small crystallites of around 10-20 nm. Electron diffraction pattern shows that the ZnO films exhibited hexagonal structure. The SEM micrograph showed that the films consist in nanocrystalline grains randomly distributed with voids in different regions. The dc conductivity found in the range of 10(-5)-10(-6) (Omega cm)(-1). The optical study showed that the spectra for all samples give the transparency in the visible range.

Structural, ferroelectric and optical properties of Bi2VO5.5 thin films deposited on platinized silicon {(100) Pt/TiO2/SiO2/Si} substrates

Bismuth vanadate (Bi2VO5.5, BVO) thin films have been deposited by a pulsed laser ablation technique on platinized silicon substrates. The surface morphology of the BVO thin films has been studied by atomic force microscopy (AFM). The optical properties of the BVO thin films were investigated using spectroscopic ellipsometric measurements in the 300–820 nm wavelength range. The refractive index (n), extinction coefficient (k) and thickness of the BVO thin films have been obtained by fitting the ellipsometric experimental data in a four-phase model (air/BVOrough/BVO/Pt). The values of the optical constants n and k that were determined through multilayer analysis at 600 nm were 2.31 and 0.056, respectively. For fitting the ellipsometric data and to interpret the optical constants, the unknown dielectric function of the BVO films was constructed using a Lorentz model. The roughness of the films was modeled in the Brugmann effective medium approximation and the results were compared with the AFM observations.

Accuracy of absorbed dose in external photon beam radiotherapy : what level is sufficient and how to approach it?

Radiation therapy (RT) plays currently significant role in curative treatments of several cancers. External beam RT is carried out mostly by using megavoltage beams of linear accelerators. Tumor eradication and normal tissue complications correlate to dose absorbed in tissues. Normally this dependence is steep and it is crucial that actual dose within patient accurately correspond to the planned dose. All factors in a RT procedure contain uncertainties requiring strict quality assurance. From hospital physicist´s point of a view, technical quality control (QC), dose calculations and methods for verification of correct treatment location are the most important subjects. Most important factor in technical QC is the verification that radiation production of an accelerator, called output, is within narrow acceptable limits. The output measurements are carried out according to a locally chosen dosimetric QC program defining measurement time interval and action levels. Dose calculation algorithms need to be configured for the accelerators by using measured beam data. The uncertainty of such data sets limits for best achievable calculation accuracy. All these dosimetric measurements require good experience, are workful, take up resources needed for treatments and are prone to several random and systematic sources of errors. Appropriate verification of treatment location is more important in intensity modulated radiation therapy (IMRT) than in conventional RT. This is due to steep dose gradients produced within or close to healthy tissues locating only a few millimetres from the targeted volume. The thesis was concentrated in investigation of the quality of dosimetric measurements, the efficacy of dosimetric QC programs, the verification of measured beam data and the effect of positional errors on the dose received by the major salivary glands in head and neck IMRT. A method was developed for the estimation of the effect of the use of different dosimetric QC programs on the overall uncertainty of dose. Data were provided to facilitate the choice of a sufficient QC program. The method takes into account local output stability and reproducibility of the dosimetric QC measurements. A method based on the model fitting of the results of the QC measurements was proposed for the estimation of both of these factors. The reduction of random measurement errors and optimization of QC procedure were also investigated. A method and suggestions were presented for these purposes. The accuracy of beam data was evaluated in Finnish RT centres. Sufficient accuracy level was estimated for the beam data. A method based on the use of reference beam data was developed for the QC of beam data. Dosimetric and geometric accuracy requirements were evaluated for head and neck IMRT when function of the major salivary glands is intended to be spared. These criteria are based on the dose response obtained for the glands. Random measurement errors could be reduced enabling lowering of action levels and prolongation of measurement time interval from 1 month to even 6 months simultaneously maintaining dose accuracy. The combined effect of the proposed methods, suggestions and criteria was found to facilitate the avoidance of maximal dose errors of up to even about 8 %. In addition, their use may make the strictest recommended overall dose accuracy level of 3 % (1SD) achievable.

Trap-State Dynamics in Visible-Light-Emitting ZnO:MgO Nanocrystals

Oleate-capped ZnO:MgO nanocrystals have been synthesized that are soluble in nonpolar solvents and which emit strongly in the visible region (450−600 nm) on excitation by UV radiation. The visible emission involves recombination of trap states of the nanocrystalline ZnO core and has a higher quantum yield than the band gap UV exciton emission. The spectrally resolved dynamics of the trap states have been investigated by time-resolved emission spectroscopy. The time-evolution of the photoluminescence spectra show that there are, in fact, two features in the visible emission whose relative importance and efficiencies vary with time. These features originate from recombination involving trapped electrons and holes, respectively, and with efficiencies that depend on the occupancy of the trap density of states.

Investigations of the scaling criteria for a mild combustion burner

In this paper, a new strategy for scaling burners based on "mild combustion" is evolved and adopted to scaling a burner from 3 to a 150 kW burner at a high heat release Late of 5 MW/m(3) Existing scaling methods (constant velocity, constant residence time, and Cole's procedure [Proc. Combust. Inst. 28 (2000) 1297]) are found to be inadequate for mild combustion burners. Constant velocity approach leads to reduced heat release rates at large sizes and constant residence time approach in unacceptable levels of pressure drop across the system. To achieve mild combustion at high heat release rates at all scales, a modified approach with high recirculation is adopted in the present studies. Major geometrical dimensions are scaled as D similar to Q(1/3) with an air injection velocity of similar to 100 m/s (Delta p similar to 600 mm water gauge). Using CFD support, the position of air injection holes is selected to enhance the recirculation rates. The precise role of secondary air is to increase the recirculation rates and burn LIP the residual CO in the downstream. Measurements of temperature and oxidizer concentrations inside 3 kW, 150 kW burner and a jet flame are used to distinguish the combustion process in these burners. The burner can be used for a wide range of fuels from LPG to producer gas as extremes. Up to 8 dB of noise level reduction is observed in comparison to the conventional combustion mode. Exhaust NO emissions below 26 and 3 ppm and temperatures 1710 and 1520 K were measured for LPG and producer gas when the burner is operated at stoichiometry. (c) 2004 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Studies in bubble formation—II bubble formation under constant pressure conditions

Bubble formation under constant pressure conditions has been investigated for wide range of variation of liquid properties.Air bubbles were formed from single horizontal orifices submerged in liquids whose viscosity varied from 1·0 to 600 cPs and surface tension from 37 to 72 dyn/cm. Air flow rate was varied from 2 to 250 cm3/sec and the orifice diameter from 0·0515 to 0·4050 cm.

Studies on oxovanadium (IV) oxalate hydrates

The oxalato complexes, VOC2O4·2H2O and VOC2O4·4H2O, are described. Their magnetic moments correspond to one unpaired electron showing the tetravalency of vanadium. They are monomeric in aqueous solution. Thermal studies suggest VO2 formation when the compounds are decomposed. Infrared spectra reveal covalent bonding between the vanadium and the oxalate group and the coordinated water. The tetrahydrate has also some lattice held water. The weak band at 780 mμ and a shoulder at 600 mμ are due to d ↔ d transitions and the absorption in the ultra violet is due to charge transfer within the VO2+ group. The dihydrate is assigned a stable five co-ordinated pyramidal structure; while the tetrahydrate, a distorted octahedron with one water molecule loosely bound along the V---O axis and the other outside the co-ordination sphere.

Biosynthesis of valine and isoleucine in plants II. Dihydroxyacid dehydratase from Phaseolus radiatus

1. 1. An enzyme catalysing the conversion of α,β-dihydroxyisovalerate and α,β-dihydroxy-β-methylvalerate to α-ketoisovalerate and α-keto-β-methylvalerate has been partially purified from green gram (Phaseolus radiatus), and its characteristics studied. 2. 2. A natural inhibitor, heat stable and inorganic in nature, was observed in the crude extracts. 3. 3. The observed Km values for α-β-dihydroxyisovalerate and α,β-dihydroxy-β-methylvalerate were 2.4 · 10-3 M and 9 · 10-4 M, respectively. 4. 4. The enzyme required the presence of a divalent metal ion (Mg2+, Mn2+ or Fe2+) for maximal activity. Heavy metals like Ag+ and Hg2+ were inhibitory. 5. 5. The optimal activity was around pH 8.0 and the optimum temperature at 52°. The activation energy is found to be 12 600 cal/mole. 6. 6. The enzyme was inhibited by p-hydroxymercuribenzoate, N-ethylmaleimide and sulphydryl compounds like cysteine, glutathione, 2-mercaptoethanol and 2,3-dimercaptopropanol. The inhibition by p-hydroxymercuribenzoate could not be reversed by any of the sulfhydryl compounds tested.

Porphyrin synthesis in drug induced hepatic porphyria

Liver δ-aminolaevulate (ALA) synthetase and ALA dehydratase are induced to a greater extent in 3,5-diethoxy carbonyl-1,4-dihydrocollidine (DDC) injected mice as compared to the allyl isopropyl acetamide (AIA) injected rats. DDC treated mice do not show an increase in porphobilinogen (PEG) levels commensurate with the increase in ALA levels and the two enzyme activities, but accumulate enormous quantities of protoporphyrin in the liver. Normal mouse liver has an inherent greater capacity to convert PBG to porphyrins as compared to that of the rat. This together with the inhibition of iron incorporation into protoporphyrin in vivo at later stages of DDC administration can account for the large accumulation of protoporphyrin in these animals.

Onko tutkijan sukupuolella väliä? : Kemian ja fysiikan alan tutkijoiden ja tohtoriopiskelijoiden tutkijanura IDECAT-verkostossa sukupuoliperspektiivistä.

Tutkimukseni kohteena ovat mies- ja naispuoliset tutkijat ja tohtoriopiskelijat, jotka ovat osallistuneet katalyysitutkimukseen keskittyvän tutkimusverkosto IDECAT:in toimintaan. Tutkielmassani pyrin selvittämään, onko naisten ja miesten tutkijanuran välillä eroa ja jos on, niin minkälainen tämä ero on. Pyrin myös saamaan selville, onko naisten tutkijanuralla esteitä ja esiintyykö tiedeyhteisössä sukupuolesta johtuvaa syrjintää. IDECAT (Integrated Design of Catalytic Nanomaterials for a Sustainable Production) on EU-rahoitteinen, kemian tekniikkaan liittyvään katalyysitutkimukseen keskittyvä tutkimusverkosto, johon kuuluu alan tutkimusyksiköitä ja yliopistoja 12 Euroopan maasta. IDECAT:iin kuuluu noin 500-600 henkilöä. Tutkimukseni pohjautuu kahteen kyselytutkimukseen, jotka toteutettiin Internetissä 2009-2010. Ensimmäinen kyselytutkimus oli vastaajien saatavilla loka-marraskuussa 2009 ja siinä selvitettiin IDECAT:in tutkijoiden ja tohtoriopiskelijoiden tasa-arvotilannetta yleisesti. Kyselyyn vastasi 83 henkilöä, joista 51% oli naisia ja 49 % miehiä. Kyselyssä käytettiin strukturoitua kyselylomaketta ja tulokset analysoitiin kvantitatiivisesti SPSS tilasto-ohjelmalla. Tilastollisena menetelmänä käytän ristiintaulukointia. Toinen kyselytutkimus (jatkokysely) keskittyy tiedeyhteisössä tapahtuvaan sukupuolesta johtuvaan syrjintään ja se oli vastaajien saatavilla huhti-toukokuussa 2010. Jatkokyselyn kysymykset ovat avokysymyksiä ja ne analysoitiin laadullisesti. Jatkokyselyyn vastasi 24 henkilöä, joista 6 kuvasi yksityiskohtaisesti syrjintäkokemuksiaan tiedeyhteisössä. Teoreettisena viitekehyksenä käytän tutkimuksessani Joan Ackerin sukupuolittuneen organisaation teoriaa ja siihen liittyviä, organisaation toiminnassa ilmeneviä sukupuolittuneita prosesseja. Sukupuolittuneet prosessit ovat ajattelutapoja , käytäntöjä ja asenteita, joilla sukupuolet erotetaan toisistaan ja joilla tuotetaan sukupuolten välisiä valtasuhteita. Naisten ja miesten tutkijanuran välillä on aineistossani joitakin merkittäviä eroja. Sukupuolesta johtuva syrjintä on yleistä vastaajien keskuudessa ja naiset ovat kokeneet sitä useammin kuin miehet. 67% naisvastaajista ja 37% miesvastaajista on kokenut sukupuolesta johtuvaa syrjintää. Naisvastaajat myös kokevat miehiä useammin, että he eivät saa riittävästi tukea ja kannustusta esimiehiltään. Lisäksi naisia on pyydetty mukaan tieteelliseen yhteistyöhön miehiä harvemmin. Useimmat muuttujat eivät kuitenkaan tuo eroa sukupuolten välille. Tutkijanaiset kokevat ylenemismahdollisuutensa lähes yhtä hyviksi kuin miehet, naiset ja miehet työskentelevät yhtä usein määräaikaisissa tehtävissä ja naiset työskentelevät kokopäiväisesti lähes yhtä usein kuin miehet. Naiset pitävät perheen ja työn yhdistämistä helppona. Sukupuolittuneita prosesseja ilmenee erityisesti sukupuolten väliseen työnjakoon ja sosiaalisen tuen ja vallan jakoon tiedeyhteisössä liittyvissä tilanteissa. Sukupuolittuneisuus ei kuitenkaan ole totaalista, monien kyselyn muuttujien kohdalla sukupuolittumista tai eroa sukupuolten välille ei tullut. Monet kyselyn muuttujat osoittavatkin, että naiset ja miehet kokevat, että heitä kohdellaan melko tasa-arvoisesti. Tietyillä osa-alueilla epätasa-arvoisen kohtelun kokemukset ovat kuitenkin yleisiä, mikä tuottaa ristiriitaisen kuvan tiedeyhteisön tasa-arvotilanteesta. Tämä voi viitata siihen, että tutkijanaisten ja miesten asemat ja roolit tiedeyhteisössä eivät ole pysyviä ja staattisia, vaan aktiivisessa muutoksen tilassa. Tutkijanaisten asemaa tiedeyhteisössä voidaan lisäksi parantaa reagoimalla ja puuttumalla sukupuolesta johtuvaan syrjintään, pitämällä tasa-arvoasioita esillä sekä kiinnittämällä huomiota johtamiskäytäntöihin, esimerkiksi palkkaamalla lisää naisjohtajia. Avainsanat Keywords: Sukupuolittunut organisaatio, sukupuolittuneet prosessit, kyselytutkimus, kvantitatiivinen tutkimus, tiedeyhteisö, sukupuolisyrjintä, tutkijanaiset, naistutkijat, sukupuolten tasa-arvo, gendered organization, academia, female scientists, gender equality

Vaggvisor i Kvevlax : Språkliga strukturer och konstruktioner

Lullabies in Kvevlax. Linguistic structures and constructions. The study is a linguistic analysis of constructions that shape the texts used in lullabies in Kvevlax in Ostrobothnia in Finland. The empirical goal is to identify linguistic constructions in traditional lullabies that make use of the dialect of the region. The theoretical goal was to test the usability of Construction Grammar (CxG) in analyses of this type of material, and to further develop the formal description of Construction Grammar in such a way as to make it possible to analyze all kinds of linguistically complex texts. The material that I collected in the 1960s comprises approximately 600 lullabies and concomitant interviews with the singers on the use of lullabies. In 1991 I collected additional material in Kvevlax. The number of informants is close to 250. Supplementary material covering the Swedish-language regions in Finland was compiled from the archives of the Society of Swedish Literature in Finland. The first part of the study is mainly based on traditional grammar and gives general information about the language and the structures used in the lullabies. In the detailed study of the Kvevlax lullabies in the latter part of the study I use a version of Construction Grammar intended for the linguistic analysis of usage-based texts. The analysis focuses on the most salient constructions in the lullabies. The study shows that Construction Grammar as a method has more general applicability than traditional linguistic methods. The study identifies important constructions, including elements typical of this genre, that structure the text in different variants of the same lullabies. In addition, CxG made it possible to study pragmatic aspects of the interactional, cultural and contextual language that is used in communication with small children. The constructions found in lullabies are also used in language in general. In addition to being able to give detailed linguistic descriptions of the texts, Construction Grammar can also explain the multidimensionality of language and the variations in the texts. The use of CxG made it possible to show that variations are not random but follow prototypical linguistic patterns, constructions. Constructions are thus found to be linguistic resources with built-in variation potentials.

Studies on induction of delta-aminolevulinic acid synthetase in mouse liver

Administration of 3,5-diethoxy carbonyl-1,4-dihydrocollidine (DDC) to mice resulted in a striking increase in the level of δ-aminolevulinic acid (ALA) synthetase in liver. Although the enzyme activity was primarily localized in mitochondria and postmicrosomal supernatant fluid, a significant level of activity was also detected in purified nuclei. The time course of induction showed a close parallelism between the bound and free enzyme activities with the former always accounting for a higher percentage of the total activity as compared to the latter. Studies with cycloheximide indicated a half-life of around 3 hr for both the bound and free ALA synthetase. Actinomycin D and hemin prevented enzyme induction when administered along with DDC, but when administered 12 hr after DDC treatment Actinomycin D did not lead to a decay of either the bound or free enzyme activity and hemin inhibited the bound enzyme activity but not the free enzyme level. The molecular sizes of the mitochondrial and cytosolic ALA synthetase(s) were found to be similar on sephadex columns.

High Rate Capability of Porous LiNi1/3Co1/3Mn1/3O2 Synthesized by Polymer Template Route

Layered LiNi1/3Co1/3Mn1/3O2, which is isostructural with LiCoO2, is considered as a potential cathode material for Li-ion batteries. Submicrometer sized porous particles are useful for high discharge rates. The present work involves a synthesis of submicrometer sized porous particles of LiNi1/3Co1/3Mn1/3O2 using a triblock copolymer as a soft template. The precursor obtained from the reaction is heated at different temperatures between 600 and 900 degrees C for 6 h to get the final product samples. The compound attains increased crystallinity with an increase in the temperature of preparation. However, there is a decrease in the surface area and also in the porosity of the sample. Nevertheless, the LiNi1/3Co1/3Mn1/3O2 sample prepared at 900 degrees C exhibits a high rate capability and stable capacity retention on cycling. The electrochemical performance of LiNi1/3Co1/3Mn1/3O2 prepared in the absence of the polymer template is inferior to that of the sample prepared in the presence of the polymer template. (C) 2010 The Electrochemical Society. [DOI: 10.1149/1.3364944] All rights reserved.

Rapid growth of nanotubes and nanorods of wurtzite ZnO through microwave-irradiation of a metalorganic complex of zinc and a surfactant in solution

Large quantities of single-crystalline ZnO nanorods and nanotubes have been prepared by the microwave, irradiation of a metalorganic complex of zinc, in the presence of a surfactant. The method is simple, fast, and inexpensive (as it uses a domestic microwave oven), and yields pure nanostructures of the hexagonal wurtzite phase of ZnO in min, and requires no conventional templating. The ZnO nanotubes formed have a hollow core with inner diameter varying from 140-160 nm and a wall of thickness, 40-50 nm. The length of nanorods and nanotubes varies in the narrow range of 500-600 nm. These nanostructures have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction (SAED). The ZnO nanorods and nanotubes are found by SAED to be single-crystalline. The growth process of ZnO nanorods and nanotubes has been investigated by varying the surfactant concentration and microwave irradiation time. Based on the various results obtained, a tentative and plausible mechanism for the formation of ZnO nanostructures is proposed.