Processo biotecnológico voltado a produção de estoques poliploides do camarão-branco litopenaeus vannamei (decapoda, penaeidae)

without practical results so far. Protocols used in biotechnological cultured aquatic organisms aimed at increasing growth rates and disease resistance, have been studied and perfected. Among the available techniques, the application of chromosomal manipulation, although still nascent, is presented as a tool aimed at mitigating ecological and economical issues in shrimp farming. The polyploidization artificial method already employed in fish and shellfish, has been widely researched for use in farmed shrimp. Some limitations of this method of expansion in shrimp refer to a better knowledge of cytogenetic aspects, the level of sexual dimorphism and performance in growing conditions. To contribute on some of these issues, the present study aimed to characterize cytogenetic species Litopenaeus vannamei (Decapoda) and Artemia franciscana (Anostraca), analyze the effectiveness of methods for detection of ploidy, through the use of flow cytometry in processes of induction polyploidy cold thermal shock at different stages of development of newly fertilized eggs. Additionally, aimed also the qualitative and quantitative comparison of larval development between diploid and polyploid organisms, besides the identification of sexual dimorphism in L. vannamei, through geometric morphometrics. The results provide information relevant to the improvement and widespread use of biotechnological methods applied toward national productivity in shrimp farming

Estudo da sinterização do aço inox 316L reforçado com 3% Carbeto de Tântalo - TaC

The present work shows a contribution to the studies of development and solid sinterization of a metallic matrix composite MMC that has as starter materials 316L stainless steel atomized with water, and two different Tantalum Carbide TaC powders, with averages crystallite sizes of 13.78 nm and 40.66 nm. Aiming the metallic matrix s density and hardness increase was added different nanometric sizes of TaC by dispersion. The 316L stainless steel is an alloy largely used because it s high resistance to corrosion property. Although, its application is limited by the low wear resistance, consequence of its low hardness. Besides this, it shows low sinterability and it cannot be hardened by thermal treatments traditional methods because of the austenitic structure, face centered cubic, stabilized mainly in nickel presence. Steel samples added with TaC 3% wt (each sample with different type of carbide), following a mechanical milling route using conventional mill for 24 hours. Each one of the resulted samples, as well as the pure steel sample, were compacted at 700 MPa, room temperature, without any addictive, uniaxial tension, using a 5 mm diameter cylindrical mold, and quantity calculated to obtain compacted final average height of 5 mm. Subsequently, were sintered in vacuum atmosphere, temperature of 1290ºC, heating rate of 20ºC/min, using different soaking times of 30 and 60 min and cooled at room temperature. The sintered samples were submitted to density and micro-hardness analysis. The TaC reforced samples showed higher density values and an expressive hardness increase. The complementary analysis in optical microscope, scanning electronic microscope and X ray diffractometer, showed that the TaC, processed form, contributed with the hardness increase, by densification, itself hardness and grains growth control at the metallic matrix, segregating itself to the grain boarders

Avaliação do desempenho do aço D6 tratado termicamente e netretado em plasma com gaiola catódica visando aplicação industrial

In this research there was an evaluation of the best conditions of nitriding in plasma within a cathodic cage at an atmosphere of 80% N2-20%H2 in samples of tool manganese steel AISI D6, cold working, treated thermally in the following conditions: tension relief, treated thermally to temperature of maximum heat, temperate heat and temperate and temperate heat. A pressure of 2.5mbar and temperatures of 400 and 300ºC com treatment time of two and three hours were used to evaluate its performance as cutting tool (punch) of bicycle backs. Hardness, micro-structural aspects (layer thickness, interface, grain size etc), and crystal phases on the surface were appraised. When treated to tension relief, thermally treated to maximum heat temperature, temperature and temperate heat, the samples presented hardness levels of 243HV, 231HV, 832HV, and 653HV, respectively. The best nitrification conditions were: four hours and 300ºC for heat samples. A superficial hardness of 1000HV and a 108µm thickness for the nitrided layer were found in these samples

Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Efeito da moagem de alta energia na microestrutura e nas propriedades magnéticas do compósito wc-10%p.Co

This work a studied the high energy milling effect in microstructure and magnetic properties of the WC-10wt.%Co composite. The composite powders were prepared by mechanical mixed and milled at 2 hours, 100 hours, 200 hours and 300 hours in planetary milling. After this process the composite were compacted in stainless steel die with cylindrical county of 10 mm of diameter, at pressure 200 Mpa and sintered in a resistive furnace in argon atmosphere at 1400 oC for 5 min. The sintered composite were cutted, inlaid, sandpapered, and polished. The microestrutural parameters of the composite was analyzed by X-ray diffraction, scanning electronic microscopy, optical microscopy, hardness, magnetic propriety and Rietveld method analyze. The results shows, with milling time increase the particle size decrease, it possibility minor temperature of sintering. The increase of milling time caused allotropic transformation in cobalt phase and cold welding between particles. The cold welding caused the formation of the particle composite. The X-ray diffraction pattern of composite powders shows the WC peaks intensity decrease with the milling time increase. The X-ray diffraction pattern of the composite sintered samples shows the other phases. The magnetic measurements detected a significant increase in the coercitive field and a decrease in the saturation magnetization with milling time increase. The increase coercitive field it was also verified with decrease grain size with milling time increase. For the composite powders the increase coercitive field it was verified with particle size reduction and saturation magnetization variation is relate with the variation of free cobalt. The Rietveld method analyze shows at milling time increase the mean crystalline size of WC, and Co-cfc phases in composite sintered sample are higher than in composite powders. The mean crystallite size of Co-hc phase in composite powders is higher than in composite sintered sample. The mean lattice strains of WC, Co-hc and Co-cfc phases in composite powders are higher than in composite sintered samples. The cells parameters of the composite powder decrease at milling time increase this effect came from the particle size reduction at milling time increase. In sintered composite the cells parameters is constant with milling time increase

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Benthic response to upwelling events off the SE Brazilian coast

The main aim of the present study was to evaluate and compare temporal responses of the benthos in 2 continental shelf areas (Cabo Frio and Ubatuba) off the SE Brazilian coast. In Cabo Frio (23 degrees S, 42 degrees W), the western boundary coastal upwelling of the South Atlantic Central Water (SACW) enhances primary productivity, potentially increasing food supply to the benthic communities via sinking of particulate organic carbon (POC). In contrast, POC fluxes in Ubatuba (23 degrees S, 45 degrees W) are expected to be comparatively lower because SACW remains subsurface. We analyzed the temporal and spatial input of phytodetritus (concentration of chlorophyll a in sediments) and the benthic microbial biomass (estimated by ATP-based carbon content in sediments). Median surface chlorophyll concentration was computed for all daily available SeaWiFS images (from 2001 and 2002) to follow chlorophyll a inputs. All parameters used to investigate benthic responses in the study areas showed consistently higher values in Cabo Frio than in Ubatuba. The results showed that benthic response to upwelling may last months, fueling the microbial communities in the Cabo Frio region.

Vertical distribution of benthic invertebrate larvae during an upwelling event along a transect off the tropical Brazilian continental margin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of hot and cold smoking processes on organoleptic properties, yield and composition of matrinxa fillet

Foi avaliado o efeito do processo de defumação a quente (45-90ºC/5 horas) e a frio (27-45ºC/10 horas) nas propriedades organolépticas, no rendimento e na composição dos filés de matrinxã (Brycon cephalus). Não houve diferença significativa no rendimento de filés defumados e não-defumados. As perdas no processo de defumação foram significativamente maiores para defumação a quente (19,37%) em comparação à defumação a frio (17,08%). O processo de defumação reduziu a umidade (in natura = 72,91%; defumado a quente = 58,51%; e defumado a frio = 59,68%) e aumentou os teores de proteína bruta, lipídios e cinzas. Houve diferença significativa somente nos teores de proteína no defumado a quente (28,07%) e defumado a frio (27,14%). O processo a frio resultou em melhor aparência e cor de filé, enquanto o processo a quente melhorou o sabor, o teor de sal e a aparência geral. O aroma e a textura não diferiram significativamente entre os processos. O processo de defumação a quente melhora as propriedades organolépticas e os níveis de proteína do filé de matrinxã.

Half-sib progenies evaluation in velvet grass

O capim-lanudo (Holcus lanatus L.) possui grande potencial de utilização como pastagem de inverno nas regiões subtropicais, devido a seu bom estabelecimento, persistência, produção, resistência ao frio, palatabilidade e capacidade de afilhamento. O objetivo deste trabalho foi estimar a variabilidade genética e a herdabilidade de caracteres agronômicos e identificar progênies superiores. Foram avaliadas 60 progênies de meios-irmãos, para altura (NH) e diâmetro da planta na fase vegetativa, duração do ciclo vegetativo (ciclo), altura final (FH) e número de afilhos. Houve diferença entre progênies para todos os caracteres. As estimativas de herdabilidade foram de 38%, 32%, 92%, 57% e 64% para NH, diâmetro, ciclo, FH e afilhos, respectivamente. O maior ganho genético estimado foi de 30,77 % para o número de afilhos. Existe variabilidade para todos os caracteres e são esperados ganhos na seleção entre progênies.

Effect of Environmental Temperature During the First Week of Brooding Period on Broiler Chick Body Weight, Viscera and Bone Development

O presente trabalho teve como objetivo estudar o efeito de diferentes temperaturas-ambiente durante a primeira semana de vida de pintos de corte sob parâmetros zootécnicos, desenvolvimento visceral e crescimento ósseo. Foram utilizados 240 pintos de um dia, alojados em 3 câmaras climáticas, com temperaturas constantes de 20, 25 e 35°C do 1° ao 7° dia de vida. Diariamente, o consumo de água e ração, bem como o peso vivo, o peso relativo do fígado, moela, coração, saco vitelino e bursa de Fabricius foram avaliados. A tíbia e o fêmur também foram pesados e o comprimento e espessura (diâmetro médio) mensurados. As aves criadas a 20°C ganharam menos peso e consumiram menos ração do que aves mantidas a 25°C e menos água do que aves mantidas a 35°C. O peso relativo do fígado, coração e moela foram afetados pela temperatura ambiente, entretanto, não foi observado efeito da temperatura de criação sobre o peso do saco vitelino e bursa de Fabricius. Os dados mostraram que todos os parâmetros ósseos pesquisados aumentaram com a idade das aves. A temperatura ambiente não afetou a espessura da tíbia e do fêmur, mas foi observado um aumento significativo no peso e comprimento dos ossos com o aumento da temperatura ambiente. Os resultados desse experimento mostraram que o estresse por frio (20°C) reduziu o crescimento ósseo bem como o peso vivo das aves, durante os primeiros sete dias após a eclosão.

Effect of Fusarium graminearum and infection index on germination and vigor of maize seeds

Patógenos em sementes de milho (Zea mays) causam sérios problemas, como a perda de sua capacidade germinativa. O objetivo do trabalho foi determinar qual o melhor tempo para infecção das sementes de milho com Fusarium graminearum, para posterior avaliação dos danos causados pelo fungo na germinação e vigor das mesmas. As sementes foram colocadas sobre meio de BDA contendo o patógeno e incubadas por 4, 8, 16 e 32 h. Após os respectivos períodos de incubação, estas foram submetidas ao teste de sanidade (papel de filtro), com duas variações, sem e com assepsia superficial, usando hipoclorito de sódio a 1% de cloro ativo, por 3 min. Determinado o melhor tempo para infecção, outras sementes foram infetadas com o patógeno, para realização dos testes de germinação e vigor (envelhecimento acelerado e teste de frio) com uma mistura de sementes sadias (colocadas sobre o meio BDA) e sementes inoculadas, resultando em 0, 20, 40, 60, 80 e 100% de sementes infetadas com o fungo em estudo. Os resultados obtidos mostraram que o período de incubação de 32 h foi suficiente para se obter sementes infetadas. Com relação à germinação, não houve diferenças significativas entre os diferentes níveis de infecção, provavelmente devido ao alto vigor das sementes de milho testadas. Quanto aos testes de vigor, os níveis de infecção diferiram significativamente da testemunha, apesar de não terem diferido entre si.

Viscosidade do Sangue como Parâmetro de Diagnóstico da Síndrome Ascítica em Linhagens de Frangos de Corte com Diferentes Suscetibilidade

O objetivo deste trabalho foi investigar o desenvolvimento de ascites em duas linhagens diferentes de frangos de corte, Hubbard e Pescoço-pelado, através da variação da viscosidade do sangue. As aves foram criadas até 45 dias de idade em duas temperaturas ambiente diferentes (termoneutra e fria) e com dieta de ração à base de milho e farelo de soja, peletizada e de alta energia. Aos 28 e 45 dias de idade, amostras de 8 mL de sangue foram obtidas para determinação da viscosidade aparente em um viscosímetro de cilindros concêntricos da marca Brookfield, modelo LVDII+ e para determinação do hematócrito. Aos 28 dias de idade foram verificadas algumas ocorrências de ascite nas aves da linhagem Hubbard criadas à temperatura ambiente fria, e aos 45 dias de idade, todos os frangos de corte dessa linhagem criados no ambiente frio apresentaram ascite. A linhagem Pescoço-pelado foi resistente ao desenvolvimento de ascite em todas as idades e temperaturas ambiente. A análise dos resultados da viscosidade aparente do sangue indicaram que aves com valores similares ou maiores que 4 cP (centipoise) apresentaram ascite. Podemos concluir que na linhagem comercial o valor de 4 cP para a viscosidade aparente parece identificar o desenvolvimento de ascite.

Yeast extract and prebiotic in pre-initial phase diet for broiler chickens raised under different temperatures

Objetivou-se nesta pesquisa avaliar o desempenho, o rendimento de carcaça e a morfometria intestinal de frangos de corte criados em diferentes temperaturas e que receberam na fase pré-inicial ração contendo ou não extrato de leveduras e prebiótico. Foram utilizados 1.440 pintos machos de 1 dia de idade, criados em diferentes câmaras climáticas. As rações, acrescidas ou não de extrato de leveduras e prebiótico, foram oferecidas somente na fase pré-inicial (1 a 7 dias). A partir do oitavo dia, todas as aves receberam a mesma ração, reajustada de acordo com as recomendações usuais. Adotou-se o delineamento experimental inteiramente casualizado em arranjo fatorial 3 × 2 × 2, composto de três temperaturas de criação (calor, conforto e frio) e dois níveis de extrato de leveduras (com ou sem) e prebiótico (com ou sem). O desempenho das aves foi avaliado considerando o ganho de peso, o consumo de ração, a conversão alimentar e a viabilidade aos 42 dias de idade. Também foram avaliados o rendimento de carcaça e a morfometria intestinal. O calor ambiente prejudicou o desempenho e o rendimento de carcaça. A inclusão de prebiótico na ração pré-inicial aumentou o ganho de peso e melhorou a conversão alimentar das aves criadas no calor. A inclusão dos produtos na ração de frangos de corte criados em ambiente de calor e no frio tem efeito benéfico sobre as vilosidades das aves.