A novel, open access, elliptical cross-section magnet for paediatric MRI

Almost all clinical magnetic resonance imaging systems are based on circular cross-section magnets. Recent advances in elliptical cross-section RF probe and gradient coil hardware raise the question of the possibility of using elliptical cross-section magnet systems, This paper presents a methodology for calculating rapidly the magnetic fields generated by a multi-turn coil of elliptical cross-section and incorporates this in a stochastic optimization method for magnet design, An open magnet system of elliptical cross-section is designed that both reduces the claustrophobia for the patients and allows ready access by attending physicians, The magnet system is optimized for paediatric use, The coil geometry produced by the optimization method has several novel features.

Effect of temperature and sweating on bioimpedance measurements

The effect of skin temperature and hydration status has been suggested by some researchers as a common cause of variation in bioimpedance measurements of the body. This paper details a simple method of measuring the transverse impedance of the skin. The measured resistance and reactance was found to decrease by 35% and 18% for an increase of 20 degrees C. Similarly a decrease in resistance and reactance of 20% and 25% respectively was detected after hydration of the skin. However, the changes in skin temperature and hydration were found to have no significant effect on the whole body bioimpedance measurements using the standard tetra-polar electrode technique. (C) 1998 Elsevier Science Ltd. All rights reserved.

A compact superconducting magnet for magnetic resonance microscopy

Magnetic resonance microscopy (MRM) depends on the use of high field, superconducting magnet systems for its operation. The magnets that are conventionally used are those that were initially designed for chemical structural analysis work. A novel, compact magnet designed specifically for MRM is presented here, and while preserving high field, high homogeneity conditions, has a length less than one-third that of conventional systems. This enables much better access to samples, an important consideration in many MRM experiments. As the homogeneity of a magnet is strongly dependent on its length, novel geometries and optimization techniques are required to meet the requirements of MRM in a compact system. An important outcome of the stochastic optimization performed in this work, is that the use used of a thin superconducting solenoid surrounded by counterwound disk windings provides a mechanism for drastic length reductions over conventional magnet designs. (C) 1998 American Institute of Physics.

Antipronation taping and temporary orthoses - Effects on tibial rotation position after exercise

Abnormal lower-limb biomechanics-in particular, abnormal pronation of the subtalar joint with concomitant increased internal rotation of the tibia-is one of the major causes of overuse injuries of the lower limb. A randomized, controlled, within-subjects research design (N = 14) was used to investigate the effect of a temporary felt orthosis and an antipronation taping technique to control the transverse tibial rotation position immediately after application and after each of two 10-minute periods of exercise. The results showed that the taping technique was superior to both the orthosis and no intervention in controlling tibial rotation position immediately after application and after 10 minutes of exercise. After 20 minutes of exercise, neither the tape nor the orthosis was significantly superior to the control; however, the trends suggested that some residual control was maintained. Future studies are needed to determine the amount of foot pronation control required to relieve symptoms in a symptomatic population in order to determine the clinical effectiveness of these treatment methods.

Frequency stabilised grating feedback laser diode for atom cooling applications

The free running linewidth of an external cavity grating feedback diode laser is on the order of a few megahertz and is limited by the mechanical and acoustic vibrations of the external cavity. Such frequency fluctuations can be removed by electronic feedback. We present a hybrid stabilisation technique that uses both a Fabry-Perot confocal cavity and an atomic resonance to achieve excellent short and long term frequency stability. The system has been shown to reduce the laser linewidth of an external cavity diode laser by an order of magnitude to 140 kHz, while limiting frequency excursions to 60 kHz relative to an absolute reference over periods of several hours. The scheme also presents a simple way to frequency offset two lasers many gigahertz apart which should find a use in atom cooling experiments, where hyperfine ground-state frequency separations are often required.

Residence time distributions of gas flowing through rotating drum bioreactors

Residence time distribution studies of gas through a rotating drum bioreactor for solid-state fermentation were performed using carbon monoxide as a tracer gas. The exit concentration as a function of time differed considerably from profiles expected for plug flow, plug flow with axial dispersion, and continuous stirred tank reactor (CSTR) models. The data were then fitted by least-squares analysis to mathematical models describing a central plug flow region surrounded by either one dead region (a three-parameter model) or two dead regions (a five-parameter model). Model parameters were the dispersion coefficient in the central plug flow region, the volumes of the dead regions, and the exchange rates between the different regions. The superficial velocity of the gas through the reactor has a large effect on parameter values. Increased superficial velocity tends to decrease dead region volumes, interregion transfer rates, and axial dispersion. The significant deviation from CSTR, plug flow, and plug flow with axial dispersion of the residence time distribution of gas within small-scale reactors can lead to underestimation of the calculation of mass and heat transfer coefficients and hence has implications for reactor design and scaleup. (C) 2001 John Wiley & Sons, Inc.

A method for the design of MRI radiofrequency coils based on triangular and pulse basis functions

This paper presents a numerical technique for the design of an RF coil for asymmetric magnetic resonance imaging (MRI) systems. The formulation is based on an inverse approach where the cylindrical surface currents are expressed in terms of a combination of sub-domain basis functions: triangular and pulse functions. With the homogeneous transverse magnetic field specified in a spherical region, a functional method is applied to obtain the unknown current coefficients. The current distribution is then transformed to a conductor pattern by use of a stream function technique. Preliminary MR images acquired using a prototype RF coil are presented and validate the design method. (C) 2002 Elsevier Science B.V. All rights reserved.

pH dependence of the progression in NMR T-2 relaxation times in post-mortem muscle

Continuous NMR T-2 relaxation measurements were carried out on seven rabbit longissimus muscle samples in the period from 25 min to 28 h post-mortem at 200 MHz for H-1. To display differences in post-mortern pH progress and extent of changes in water characteristics during conversion of muscle to meat, three of the seven animals were pre-slaughter injected with adrenaline (0.5 mg/kg live weight 4 h before sacrifice) to differentiate muscle glycogen stores at the time of slaughter. Distributed analysis of T-2 data displayed clear differences in the characteristics of the various transverse relaxation components dependent on progress in pH, as did the water-holding capacity of samples 24 h postmortem. This reveals a pronounced effect of the progressive change in pH on the subsequent development in physical/chemical states of water during the conversion of muscle to meat. Finally, the relaxation characteristics are discussed in relation to supposed post-mortem processes of protein denaturation.

Osmotic properties of the sealed tubular system of toad and rat skeletal muscle

A method was developed that allows conversion of changes in maximum Ca2+-dependent fluorescence of a fixed amount of fluo-3 into volume changes of the fluo-3-containing solution. This method was then applied to investigate by confocal microscopy the osmotic properties of the sealed tubular (t-) system of toad and rat mechanically skinned fibers in which a certain amount Of fluo-3 was trapped. When the osmolality of the myoplasmic environment was altered by simple dilution or addition of sucrose within the range 190-638 mosmol kg(-1), the sealed t-system of toad fibers behaved almost like an ideal osmometer, changing its volume inverse proportionally to osmolality However, increasing the osmolality above 638 to 2,550 mosmol kg(-1) caused hardly any change in t-system volume. In myoplasmic solutions made hypotonic to 128 mosmol kg(-1), a loss of Ca2+ from the sealed t-system of toad fibers Occurred, presumably through either stretch-activated cationic channels or store-operated Ca2+ channels. In contrast to the behavior of the t-system in toad fibers, the volume of the sealed t-system of rat fibers changed little (by

The sound field generated by tethered stingless bees (Melipona scutellaris): inferences on its potential as a recruitment mechanism inside the hive

In stingless bees, recruitment of hive bees to food sources involves thoracic vibrations by foragers during trophallaxis. The temporal pattern of these vibrations correlates with the sugar concentration of the collected food. One possible pathway for transfering such information to nestmates is through airborne sound. In the present study, we investigated the transformation of thoracic vibrations into air particle velocity, sound pressure, and jet airflows in the stingless bee Melipona scutellaris. Whereas particle velocity and sound pressure were found all around and above vibrating individuals, there was no evidence for a jet airflow as with honey bees. The largest particle velocities were measured 5 mm above the wings (16.0 +/- 4.8 mm s(-1)). Around a vibrating individual, we found maximum particle velocities of 8.6 +/- 3.0 mm s(-1) (horizontal particle velocity) in front of the bee`s head and of 6.0 +/- 2.1 mm s(-1) (vertical particle velocity) behind its wings. Wing oscillations, which are mainly responsible for air particle movements in honey bees, significantly contributed to vertically oriented particle oscillations only close to the abdomen in M. scutellaris(distances <= 5 mm). Almost 80% of the hive bees attending trophallactic food transfers stayed within a range of 5 mm from the vibrating foragers. It remains to be shown, however, whether air particle velocity alone is strong enough to be detected by Johnston`s organ of the bee antenna. Taking the physiological properties of the honey bee`s Johnston`s organ as the reference, M. scutellaris hive bees are able to detect the forager vibrations through particle movements at distances of up to 2 cm.

Primary antiphospholipid syndrome with and without Sneddon`s syndrome

The main objective of this study was to compare clinical and laboratory data obtained from patients with primary antiphospholipid syndrome (PAPS) with and without Sneddon`s syndrome (SS). A transverse study with 54 (85.2% female) PAPS patients (Sapporo criteria) was performed. Demographic, drug use, and antiphospholipid antibodies data were evaluated, as well as clinical and laboratory findings of SS. Patients were subdivided into one of two groups: PAPS with SS and PAPS without SS. Both groups were similar with respect to age (p = 0.05), gender (p = 0.34), race (p = 0.31), weight (p = 0.93), height (p = 0.27), and body mass index (p = 0.75); however, the SS group exhibited higher disease duration (96.0 +/- A 54.9 vs. 55.2 +/- A 52.0 months, p = 0.01). By definition, all PAPS with SS patients suffer from stroke, an arterial event; the frequency of stroke events (28.5 vs. 7.5%, p = 0.04), as well as of limb ischemia (100 vs. 30.0%, p < 0.0001) was higher in this group than in the PAPS without SS group. On the other hand, patients in the PAPS without SS group had more venous events, such as deep venous thrombosis, than those in the PAPS with SS group (80.0 vs. 50.0%, p = 0.03). In conclusion, an understanding of the relationship between APS and SS is important in order to identify a subgroup for which more rigorous accompaniment and therapy may be necessary.

Variation of Patterns of Malocclusion by Site of Pharyngeal Obstruction in Children

Objective: To correlate the type of dental occlusion and the type of pharyngeal lymphoid tissue obstruction in children. Design: Cross-sectional study. Setting: Ambulatory ear, nose, and throat clinic of Faculdade de Medicina da Universidade de Sao Paulo. Patients: One hundred fourteen children aged 3 to 12 years presenting with mouth breathing and snoring due to tonsil and/or adenoid enlargement. Interventions: Oroscopy and nasal fiber pharyngoscopy complemented by lateral head radiography to diagnose the type of obstruction, and clinical examination to evaluate the dental occlusion. Main Outcome Measures: Tonsil and adenoid obstruction (classified from grades 1-4) and sagittal, transverse, and vertical evaluation of dental occlusion. Results: Obstructive enlargement of both tonsils and adenoids was detected in 64.9% of the sample; isolated enlargement of the adenoids, in 21.9%; isolated enlargement of the palatine tonsils, in 7.0%; and nonobstructive tonsils and adenoids, in 6.1%. All types of pharyngeal obstruction were related to a high prevalence of posterior crossbite (36.8%). Statistically significant association was found between sagittal dental occlusion and the site of lymphoid tissue obstruction (P = .02). A higher rate of class II relationship (43.2%) was detected in the group with combined adenoid and tonsil obstructive enlargement. Isolated tonsil obstruction showed a higher rate of class III relationship (37.5%). Conclusions: Different sites of obstruction of the upper airway due to enlarged lymphoid tissue are associated with different types of dental malocclusion. Findings are relevant to orthodontic and surgical decision making in these mouth-breathing patients.

The intercalated disc of monkey myocardial cells and Purkinje fibers as revealed by scanning electron microscopy

The intercalated discs of working myocardium and Purkinje fibers of the monkey heart were examined by scanning and transmission electron microscopy. The NaOH/ultrasonication technique resulted in the digestion of connective tissue and a separation of the intercellular junctions of intercalated discs, such that these could be visualized three-dimensionally. The intercalated discs of ventricular myocytes, atrial myocytes and Purkinje fibers vary considerably in number and configuration, as do the intercalated discs of the three different layers of the ventricular myocardium. Myocytes in the subepicardial, middle and subendocardial layers of the ventricle have 1-3, 4-5 and 5-6 intercalated discs at the end of these cells, respectively, Those in the endocardial layer are characterized by the presence of small laterally-placed intercalated discs. Atrial myocytes and Purkinje fibers usually only have 1-2 intercalated discs, Individual intercalated discs in ventricular myocytes have complicated stairs with 10-30 steps and corresponding risers, while those of atrial myocytes and Purkinje fibers have simple stairs with 1-3 steps and risers, Steps equivalent to the plicate segments are characterized by densely-packed microplicae and finger-like microprojections which greatly increase surface area in vertricular myocytes, Microprojections in atrial myocytes and Purkinje fibers are sparse by comparison, Risers equivalent to the interplicate segments containing large gap junctional areas are most numerous in left ventricular myocytes, followed by right ventricular myocytes, Purkinje fibers and atrial myocytes in decreasing order. The geometric arrangement of the various types of myocytes may be related with impulse propagation. Large intercalated discs of cell trunks and series branches may participate in longitudinal propagation, while small laterally-placed ones may be the site of transverse propagation.

Biomechanical analysis of sutures used for mesh fixation in the donor area after removal of the rectus abdominis muscle

Background: The use of synthetic mesh for abdominal wall closure after removal of the rectus abdominis is established but not standardised. This study compares two forms of mesh fixation: a simple suture, which fixes the mesh to the edges of the defect on the anterior rectus abdominis fascia; and total fixation, which incorporates the fasciae of the internal oblique, external oblique and transverse muscles in the suture, anchoring the mesh in the position of the removed muscle. Method: A total of 16 fresh cadavers were dissected. Two sutures were compared: simple and total. Three different sites were analysed: 5 cm above, 5 cm below and at the level of the umbilicus. The two sutures compared were tested in each region using a standardised technique. All sutures were performed with nylon 0, perpendicular to the linea alba. Each suture was secured to a dynamometer, which was pulled perpendicularly towards the midline until the rupture of the aponeurosis. `Rupture resistance` was measured in kilogram force. The mean among the groups was compared using the paired Student`s t-test to a significance level of 1% (p < 0.01). Results: The mean rupture resistance of the total suture was 160% higher than that of the simple suture. Conclusion: The total suture includes the external oblique, internal oblique and transverse fasciae, which are multi-directional, and creates a much higher resistance when compared with the simple suture. Total suture may reduce the incidence of bulging and hernias of the abdominal wall after harvesting the rectus abdominis muscle, but comparative clinical studies are necessary. (C) 2010 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

Anatomic Landmarks for Localization of the Spinal Accessory Nerve

This anatomical study examines the anatomic topography and landmarks for localization of the spinal accessory nerve (SAN) during surgical dissections in 40 fresh human cadavers (2 females and 38 males; ages from 22 to 89 years with a mean of 60 years). In the submandibular region, the SAN was found anteriorly to the transverse process of the atlas in 77.5% of the dissections. When the SAN crossed the posterior belly of the digastric muscle, the mean distance from the point of crossing to the tendon of the muscle was 1.75 +/- 0.54 cm. Distally, the SAN crossed between the two heads of the SCM muscle in 45% of the dissections and deep to the muscle in 55%. The SAN exited the posterior border of the sternocleidomastoid muscle in a point superior to the nerve point with a mean distance between these two anatomic parameters of 0.97 +/- 0.46 cm. The mean overall extracranial length of the SAN was 12.02 +/- 2.32 cm, whereas the mean length of the SAN in the posterior triangle was 5.27 +/- 1.52 cm. There were 2-10 lymph nodes in the SAN chain. In conclusion, the nerve point is one of the most reliable anatomic landmarks for localization of the SAN in surgical neck dissections. Although other anatomic parameters including the transverse process of the atlas and the digastric muscle can also be used to localize the SAN, the surgeon should be aware of the possibility of anatomic variations of those parameters. Similar to previous investigations, our results suggest that the number of lymph nodes of the SAN chain greatly varies. Clin. Anat. 22:471-475, 2009. (c) 2009 Wiley-Liss, Inc.