Using an LED as a sensor and visible light communication device in a smart illumination system

The need for more efficient illumination systems has led to the proliferation of Solid-State Lighting (SSL) systems, which offer optimized power consumption. SSL systems are comprised of LED devices which are intrinsically fast devices and permit very fast light modulation. This, along with the congestion of the radio frequency spectrum has paved the path for the emergence of Visible Light Communication (VLC) systems. VLC uses free space to convey information by using light modulation. Notwithstanding, as VLC systems proliferate and cost competitiveness ensues, there are two important aspects to be considered. State-of-the-art VLC implementations use power demanding PAs, and thus it is important to investigate if regular, existent Switched-Mode Power Supply (SMPS) circuits can be adapted for VLC use. A 28 W buck regulator was implemented using a off-the-shelf LED Driver integrated circuit, using both series and parallel dimming techniques. Results show that optical clock frequencies up to 500 kHz are achievable without any major modification besides adequate component sizing. The use of an LED as a sensor was investigated, in a short-range, low-data-rate perspective. Results show successful communication in an LED-to-LED configuration, with enhanced range when using LED strings as sensors. Besides, LEDs present spectral selective sensitivity, which makes them good contenders for a multi-colour LED-to-LED system, such as in the use of RGB displays and lamps. Ultimately, the present work shows evidence that LEDs can be used as a dual-purpose device, enabling not only illumination, but also bi-directional data communication.

Essays in health economics: Volume-Outcome Effect, upcoding behaviour and the evaluation of a short-term intervention program

Evidence in the literature suggests a negative relationship between volume of medical procedures and mortality rates in the health care sector. In general, high-volume hospitals appear to achieve lower mortality rates, although considerable variation exists. However, most studies focus on US hospitals, which face different incentives than hospitals in a National Health Service (NHS). In order to add to the literature, this study aims to understand what happens in a NHS. Results reveal a statistically significant correlation between volume of procedures and better outcomes for the following medical procedures: cerebral infarction, respiratory infections, circulatory disorders with AMI, bowel procedures, cirrhosis, and hip and femur procedures. The effect is explained with the practice-makes-perfect hypothesis through static effects of scale with little evidence of learning-by-doing. The centralization of those medical procedures is recommended given that this policy would save a considerable number of lives (reduction of 12% in deaths for cerebral infarction).

Analysis of classification algorithms for crop detection using LANDSAT 8 images

Remote sensing - the acquisition of information about an object or phenomenon without making physical contact with the object - is applied in a multitude of different areas, ranging from agriculture, forestry, cartography, hydrology, geology, meteorology, aerial traffic control, among many others. Regarding agriculture, an example of application of this information is regarding crop detection, to monitor existing crops easily and help in the region’s strategic planning. In any of these areas, there is always an ongoing search for better methods that allow us to obtain better results. For over forty years, the Landsat program has utilized satellites to collect spectral information from Earth’s surface, creating a historical archive unmatched in quality, detail, coverage, and length. The most recent one was launched on February 11, 2013, having a number of improvements regarding its predecessors. This project aims to compare classification methods in Portugal’s Ribatejo region, specifically regarding crop detection. The state of the art algorithms will be used in this region and their performance will be analyzed.

Clinical use of growth hormone and glutamine in short bowel syndrome

Growth hormone (GH) and glutamine (GLN) are considered bowel trophic factors and are used experimentally after bowel resection. Their clinical uses in short bowel syndrome (SBS) are still not standardized. It is of interest to verify metabolic, nutritional and side effects of the association of GH and GLN in SBS. Three patients, 39 (A), 33 (B), and 01 years old (C) underwent bowel resection with jejunum anastomosis 15 cm (A) and 60 cm (B) distant from the Treitz angle, and 40 cm (C) preserving the ileo cecal valve. GH Saizen (Serono - A), Genotropin (Pharmacia - B), and Norditropin (Novonordisk C) were administered in doses of 0.14 mg /kg/day. GLN (0.4 g/kg/day) was given orally for 10 days (A), 30 days (B) and 60 days to patient C (0.28 g/kg/day). Central TPN and adequate oral diet was administered according to the bowel adaptation phase. On the first day after beginning treatment patient A exhibited symptoms of hypoglycemia. There were no other side effects. After treatment, body weight was higher and analysis by bioelectrical impedance showed more lean mass and less fat mass compared to pre-treatment measurements. Nitrogen retention was progressively higher with treatment. Simultaneous treatment with GH and GLN does not cause significant side effects, and is associated with a favorable distribution of the body compartments and nitrogen retention in patients with the short bowel syndrome.

Nutritional follow-up of critically ill infants receiving short term parenteral nutrition

Few studies have tried to characterize the efficacy of parenteral support of critically ill infants during short period of intensive care. We studied seventeen infants during five days of total parenteral hyperalimentation. Subsequently, according to the clinical conditions, the patients received nutritional support by parenteral, enteral route or both up to the 10th day. Evaluations were performed on the 1st, 5th, and 10th days. These included: clinical data (food intake and anthropometric measurements), haematological data (lymphocyte count), biochemical tests (albumin, transferrin, fibronectin, prealbumin, retinol-binding protein) and hormone assays (cortisol, insulin, glucagon). Anthropometric measurements revealed no significant difference between the first and second evaluations. Serum albumin and transferrin did not change significantly, but mean values of fibronectin (8.9 to 16 mg/dL), prealbumin (7.7 to 18 mg/dL), and retinol-binding protein (2.4 to 3.7 mg/dL) increased significantly (p < 0.05) from the 1st to the 10th day. The hormonal study showed no difference for insulin, glucagon, and cortisol when the three evaluations were compared. The mean value of the glucose/insulin ratio was of 25.7 in the 1st day and 15.5 in the 5th day, revealing a transitory supression of this hormone. Cortisol showed values above normal in the beginning of the study. We conclude that the anthropometric parameters were not useful due to the short time of the study; serum proteins, fibronectin, prealbumin, and retinol-binding protein were very sensitive indicators of nutritional status, and an elevated glucose/insulin ratio, associated with a slight tendency for increased cortisol levels suggest hypercatabolic state. The critically ill patient can benefit from an early metabolic support.

Low efficacy of an ultra-short term, once-daily dose triple therapy with omeprazole, azithromycin, and secnidazole for Helicobacter pylori eradication in peptic ulcer

PURPOSE: To determine the eradication rate of an ultra-short treatment schedule for Helicobacter pylori infection in a population with peptic ulcers, using omeprazole, secnidazole, and azithromycin in a once-daily dose for 3 days. METHODS: Thirty patients with peptic ulcer diagnosed by upper endoscopy and for Helicobacter pylori infection by rapid urease test and histologic examination received omeprazole 40 mg, secnidazole 1000 mg, and azithromycin 500 mg, administered once daily for 3 days. A follow-up exam was performed 12 weeks after the end of the treatment. Patients who were negative for Helicobacter pylori infection by rapid urease test and histologic examination were considered cured. RESULTS: Patients were predominantly female, and the mean age was 50 years. Duodenal peptic ulcer was found in 73% of the patients. Eradication was achieved in 9 of the 28 (32%) patients as determined from the follow-up endoscopic exam. The eradication rate by intention to treat was 30%. Side effects were present in 3% of the patients, and compliance to treatment was total. CONCLUSIONS: In spite of the low rate of side effects and good compliance, the eradication index was low. A possible drawback of this therapy is that it reduces the efficacy of macrolide and nitroimidazole compounds in subsequent treatments.

Short- and long-term outcomes of ileal pouch-anal anastomosis for ulcerative colitis

Ileal pouch-anal anastomosis was an important advancement in the treatment of ulcerative colitis. The aim of this study was to determine whether early complications of ileal pouch-anal anastomosis in patients with ulcerative colitis are associated with poor late functional results. PATIENTS AND METHODS: Eighty patients were operated on from 1986 to 2000, 62 patients with ileostomy and 18 without. The early and late complications were recorded. Specific emphasis has been placed on the incidence of pouchitis with prolonged follow-up. RESULTS: The ileostomy was closed an average of 9.2 months after the first operation. Fourteen patients were excluded from the long-term evaluation; 6 patients were lost to regular follow-up, 4 died, and 4 patients still have the ileostomy. Of the 4 patients that died, 1 died from surgical complications. Early complications after operation (41) occurred in 34 patients (42.5%). Late complications (29) occurred in 25 patients as follows: 16 had pouchitis, 3 associated with stenosis and 1 with sexual dysfunction; 5 had stenosis; and there was 1 case each of incisional hernia, ileoanal fistula, hepatic cancer, and endometriosis. Pouchitis occurred in 6 patients (9.8%) 1 year after ileal pouch-anal anastomosis, 9 (14.8%) after 3 years, 13 (21.3%) after 5 years, and 16 (26.2%) after more than 6 years. The mean daily stool frequency was 12 before and 5.8 after operation. One pouch was removed because of fistulas that appeared 2 years later. CONCLUSIONS: Ileal pouch-anal anastomosis is associated with a considerable number of early complications. There was no correlation between pouchitis and severe disease, operation with or without ileostomy, or early postoperative complications. The incidence of pouchitis was directly proportional to duration of time of follow-up.

Comprehensive comparison of a current-source and a voltage-source converter for three-phase EV fast battery chargers

This paper presents a comprehensive comparison of a current-source converter and a voltage-source converter for three-phase electric vehicle (EV) fast battery chargers. Taking into account that the current-source converter (CSC) is a natural buck-type converter, the output voltage can assume a wide range of values, which varies between zero and the maximum instantaneous value of the power grid phase-to-phase voltage. On the other hand, taking into account that the voltage-source converter (VSC) is a natural boost-type converter, the output voltage is always greater than the maximum instantaneous value of the power grid phase-to-phase voltage, and consequently, it is necessary to use a dc-dc buck-type converter for applications as EV fast battery chargers. Along the paper is described in detail the principle of operation of both the CSC and the VSC for EV fast chargers, as well as the main equations of the power theory and current control strategies. The comparison between both converters is mainly established in terms of the total harmonic distortion of the grid current and the estimated efficiency for a range of operation between 10 kW and 50 kW.

Three-phase three-level current-source converter for EVs fast battery charging systems

This paper presents a three-phase three-level fast battery charger for electric vehicles (EVs) based in a current-source converter (CSC). Compared with the traditional voltage-source converters used for fast battery chargers, the CSC can be seen as a natural buck-type converter, i.e., the output voltage can assume a wide range of values, which varies between zero and the maximum instantaneous value of the power grid phase-to-phase voltage. Moreover, using the CSC it is not necessary to use a dc-dc back-end converter in the battery side, and it is also possible to control the grid current in order to obtain a sinusoidal waveform, and in phase with the power grid voltage (unitary power factor). Along the paper is described in detail the proposed CSC for EVs fast battery charging systems: the circuit topology, the power control theory, the current control strategy and the grid synchronization algorithm. Several simulation results of the EV fast battery charger operating with a maximum power of 50 kW are presented.

Genetic algorithms for the non emergency patients transport service

The authors would like to thank the anonymous reviewers for their valuable comments and suggestions to improve the paper. The authors would like to thank Dr. Elaine DeBock for reviewing the manuscript.

Comparing standard and low-cost tools for gradient evaluation along potential cycling paths

Promoting the use of non-motorized modes of transport, such as cycling, is an important contribution to the improvement of mobility, accessibility and equity in cities. Cycling offers a fast and cheap transportation option for short distances, helping to lower pollutant emissions and contributing to a healthier way of life. In order to make the cycling mode more competitive in relation to motorized traffic, it is necessary to evaluate the potential of alternatives from the perspective of the physical effort. One way to do so consists of assessing the suitability of locations for implementing cycling infrastructures. In this work, four tools to determine the gradient along potential cycling paths are compared. Furthermore, an evaluation of the reliability of some low-cost tools to measure this parameter was conducted, by comparison with standard measurements using cartographic plans, on a field case study applied to the city of Braga, Portugal. These tools revealed a good level of accuracy for the planning stage, but proved to be less reliable for use in design.

Hand gesture recognition system based in computer vision and machine learning

"Lecture notes in computational vision and biomechanics series, ISSN 2212-9391, vol. 19"

Comparison of single and multi-objective evolutionary algorithms for robust link-state routing

Traffic Engineering (TE) approaches are increasingly impor- tant in network management to allow an optimized configuration and resource allocation. In link-state routing, the task of setting appropriate weights to the links is both an important and a challenging optimization task. A number of different approaches has been put forward towards this aim, including the successful use of Evolutionary Algorithms (EAs). In this context, this work addresses the evaluation of three distinct EAs, a single and two multi-objective EAs, in two tasks related to weight setting optimization towards optimal intra-domain routing, knowing the network topology and aggregated traffic demands and seeking to mini- mize network congestion. In both tasks, the optimization considers sce- narios where there is a dynamic alteration in the state of the system, in the first considering changes in the traffic demand matrices and in the latter considering the possibility of link failures. The methods will, thus, need to simultaneously optimize for both conditions, the normal and the altered one, following a preventive TE approach towards robust configurations. Since this can be formulated as a bi-objective function, the use of multi-objective EAs, such as SPEA2 and NSGA-II, came nat- urally, being those compared to a single-objective EA. The results show a remarkable behavior of NSGA-II in all proposed tasks scaling well for harder instances, and thus presenting itself as the most promising option for TE in these scenarios.

Localization in underground tunnels

Positioning technologies are becoming ubiquitous and are being used more and more frequently for supporting a large variety of applica- tions. For outdoor applications, global navigation satellite systems (GNSSs), such as the global positioning system (GPS), are the most common and popular choice because of their wide coverage. GPS is also augmented with network-based systems that exploit existing wireless and mobile networks for providing positioning functions where GPS is not available or to save energy in battery-powered devices. Indoors, GNSSs are not a viable solution, but many applications require very accurate, fast, and exible positioning, tracking, and navigation functions. These and other requirements have stim- ulated research activities, in both industry and academia, where a variety of fundamental principles, techniques, and sensors are being integrated to provide positioning functions to many applications. The large majority of positioning technologies is for indoor environments, and most of the existing commercial products have been developed for use in of ce buildings, airports, shopping malls, factory plants, and similar spaces. There are, however, other spaces where positioning, tracking, and navigation systems play a central role in safety and in rescue operations, as well as in supporting speci c activities or for scienti c research activities in other elds. Among those spaces are underground tunnels, mines, and even underwater wells and caves. This chapter describes the research efforts over the past few years that have been put into the development of positioning systems for underground tun- nels, with particular emphasis in the case of the Large Hadron Collider (LHC) at CERN (the European Organization for Nuclear Research), where localiza- tion aims at enabling more automatic and unmanned radiation surveys. Examples of positioning and localization systems that have been devel- oped in the past few years for underground facilities are presented in the fol- lowing section, together with a brief characterization of those spaces’ special conditions and the requirements of some of the most common applications. Section 5.2 provides a short overview of some of the most representative research efforts that are currently being carried out by many research teams around the world. In addition, some of the fundamental principles and tech- niques are identi ed, such as the use of leaky coaxial cables, as used at the LHC. In Section 5.3, we introduce the speci c environment of the LHC and de ne the positioning requirements for the envisaged application. This is followed by a detailed description of our approach and the results that have been achieved so far. Some last comments and remarks are presented in a nal section.