Preformed Phoenix Ethylene Propylene Diene Monomer (EPDM) Compression Joint Seals, MLR-93-02, 1999

There is an ongoing drive towards improvements and achieving success in effective and long term sealing of portland cement concrete pavement contraction joints. A variety of joint sealing products and procedures have been applied in Iowa in search of improvements in seal performance. Hot poured rubberized asphalt products were mainly used for sealing all joints in earlier years for highways. In the 1980s, silicone sealant products were becoming popular, especially for the major highways. As a high level of sealant performance was not achieved from silicones in Iowa conditions, other sealing products were tried. Preformed neoprene compression seals are being tried as a substitution for silicone sealants. Due to high costs of materials and installation with neoprene seals, the search for improvements through other joint sealing products and procedures continued. An agreement was made with Phoenix, North America, Inc., to provide and install preformed Ethylene Propylene Diene Monomer (EPDM) compression joint seals. The research site was a 600 ft (183 m) test section of northbound I-29 in Pottawattamie County, Iowa. Seal installation was done August 20, 1992. Seal performance has been good over the past seven years and the seals are still showing no significant signs of decreasing performance.

Neuroarthropathy of the foot revealing primary systemic amyloidosis: case report and literature review.

The aims of this review were to describe the case of a patient with debilitating neuroarthropathy of the ankles and feet and reveal a primary systemic (amyloid light chain, AL) amyloidosis and to review the relevant literature concerning the peripheral neuropathy and neuroarthropathy due to amyloidosis. We will emphasize the diagnostic pitfalls and discuss prognosis and treatments of both the peripheral neuropathy and the arthropathy related to AL amyloidosis. This is a descriptive case report of a patient with neuroarthropathy of the lower limbs due to AL amyloidosis. A review and discussion of relevant literature were conducted, based on a PubMed search from 1973 to December 2013. A 51-year-old female was diagnosed with AL amyloidosis after 20 months of investigation of small painful deformities of the feet. Chronic peripheral neuropathy occurs as a manifestation of AL amyloidosis in 25 % of cases. It may exceptionally be complicated by neuroarthropathy. In this case, the paucity of clinical and electrophysiological signs of the neuropathy delayed the diagnosis, leading to a severe arthropathy. The massive destruction of the joints dominated the clinical and the poor functional outcome. Diagnosis of AL amyloidosis should be considered in the presence of a mild peripheral neuropathy and a distal destructive and painless arthropathy. The two key diagnostic procedures are serum protein electrophoresis and nerve biopsy. Delay in treatment worsens the prognosis.

Comparison of Setting Time Measured Using Ultrasonic Wave Propagation with Saw-Cutting Times on Pavements, TR-675, 2015

At present, there is little fundamental guidance available to assist contractors in choosing when to schedule saw cuts on joints. To conduct pavement finishing and sawing activities effectively, however, contractors need to know when a concrete mixture is going to reach initial set, or when the sawing window will open. Previous research investigated the use of the ultrasonic pulse velocity (UPV) method to predict the saw-cutting window for early entry sawing. The results indicated that the method has the potential to provide effective guidance to contractors as to when to conduct early entry sawing. The aim of this project was to conduct similar work to observe the correlation between initial setting and conventional sawing time. Sixteen construction sites were visited in Minnesota and Missouri over a two-year period. At each site, initial set was determined using a p-wave propagation technique with a commercial device. Calorimetric data were collected using a commercial semi-adiabatic device at a majority of the sites. Concrete samples were collected in front of the paver and tested using both methods with equipment that was set up next to the pavement during paving. The data collected revealed that the UPV method looks promising for early entry and conventional sawing in the field, both early entry and conventional sawing times can be predicted for the range of mixtures tested.

Field Evaluation of Elliptical Steel Dowel Performance, 2006

Joints are always a concern in the construction and long-term performance of concrete pavements. Research has shown that we need some type of positive load transfer across transverse joints. The same research has directed pavement designers to use round dowels spaced at regular intervals across the transverse joint to distribute the vehicle loads both longitudinally and transversely across the joint. The goal is to reduce bearing stresses on the dowels and the two pavement slab edges and erosion of the underlying surface, hence improved long-term joint and pavement structure performance. Road salts cause metal corrosion in doweled joints, excessive bearing stresses hollow dowel ends, and construction processes are associated with cracking pavement at the end of dowels. Dowels are also a cost factor in the pavement costs when joint spacing is reduced to control curling and warping distress in pavements. Designers desire to place adequate numbers of dowels spaced at the proper locations to handle the anticipated loads and bearing stresses for the design life of the pavement. This interim report is the second of three reports on the evaluation of elliptical steel dowels. This report consists of an update on the testing and performance of the various shapes and sizes of dowels. It also documents the results of the first series of performance surveys and draws interim conclusions about the performance of various bar shapes, sizes, spacings, and basket configurations. In addition to the study of elliptical steel dowel performance, fiber reinforced polymers (FRP) are also tested as elliptical dowel material (in contrast to steel) on a section of the highway construction north of the elliptical steel test sections.

Cannabis and tobacco co-consumptions: can cannabis consumers quit cigarette smoking?

Purpose: To assess the relation between cannabis and tobacco consumption among adolescents in Switzerland and whether cannabis and tobacco co-users can quit cigarette smoking. Methods: Based on individual interviews and focus groups, 22 youths aged 15-20 discussed cannabis consumption behaviours. Twenty (14 males) were cannabis consumers - of which 18 also smoked tobacco and 2 quit tobacco smoking - and 2 were former cannabis consumers (both females and daily smokers). Data were transcribed verbatim and analyzed using Atlas.ti qualitative analysis software. Results: Among the co-consumers, 9 started with tobacco, 7 with cannabis, and 2 with both. The main consumption mode among all cannabis consumers is joints, while other ways of consuming such as food preparations and water pipes are rare and experimental. Joints always mix cannabis with tobacco for 3 reasons: to burn correctly, pure cannabis is too strong, and smoking cannabis alone is too expensive. Two cannabis consumers - one former tobacco smoker and one occasional tobacco smoker - consider rolling tobacco less addictive than cigarette tobacco alone, and hence use it in their joints. Overall cannabis is considered 'natural' and less harmful to health than tobacco. Thus, many users describe their wish, in the longer term, to quit tobacco consumption without excluding occasional cannabis consumption. Nonetheless, all coconsumers declare that they smoke cigarettes as a substitute for cannabis: For example, "If I don't have a joint, I need fags; if I don't have fags, I need joints; and if I don't have anything, I go crazy!" or "About 20 minutes after smoking a joint we feel like smoking something again, because in the joint there is pure tobacco without a filter as in cigarettes, and that creates a crazy dependency!". Finally, all co-consumers state that the consumption of one of the substances increases when trying to diminish the other: "A few months ago I stopped smoking joints for a month. Well I was smoking more than a pack [of cigarettes] a day." Similarly, the 2 former cannabis consumers increased their cigarette use since quitting cannabis. Conclusions: The majority of cannabis users co-consume tobacco as a way of compensating for one substance or the other. Using tobacco within joints implies that there is a risk that even occasional joints can revive nicotine addiction. Consequently, health professionals wishing to help adolescents in substance use cessation and prevention efforts should consider both substances in a global perspective. Sources of Support: Dept. of Public Health of the canton of Vaud.

Revisiting spatial distribution and biochemical composition of calcium-containing crystals in human osteoarthritic articular cartilage.

INTRODUCTION: Calcium-containing (CaC) crystals, including basic calcium phosphate (BCP) and calcium pyrophosphate dihydrate (CPP), are associated with destructive forms of osteoarthritis (OA). We assessed their distribution and biochemical and morphologic features in human knee OA cartilage. METHODS: We prospectively included 20 patients who underwent total knee replacement (TKR) for primary OA. CaC crystal characterization and identification involved Fourier-transform infra-red spectrometry and scanning electron microscopy of 8 to 10 cartilage zones of each knee, including medial and lateral femoral condyles and tibial plateaux and the intercondyle zone. Differential expression of genes involved in the mineralization process between cartilage with and without calcification was assessed in samples from 8 different patients by RT-PCR. Immunohistochemistry and histology studies were performed in 6 different patients. RESULTS: Mean (SEM) age and body mass index of patients at the time of TKR was 74.6 (1.7) years and 28.1 (1.6) kg/m², respectively. Preoperative X-rays showed joint calcifications (chondrocalcinosis) in 4 cases only. The medial femoro-tibial compartment was the most severely affected in all cases, and mean (SEM) Kellgren-Lawrence score was 3.8 (0.1). All 20 OA cartilages showed CaC crystals. The mineral content represented 7.7% (8.1%) of the cartilage weight. All patients showed BCP crystals, which were associated with CPP crystals for 8 joints. CaC crystals were present in all knee joint compartments and in a mean of 4.6 (1.7) of the 8 studied areas. Crystal content was similar between superficial and deep layers and between medial and femoral compartments. BCP samples showed spherical structures, typical of biological apatite, and CPP samples showed rod-shaped or cubic structures. The expression of several genes involved in mineralization, including human homolog of progressive ankylosis, plasma-cell-membrane glycoprotein 1 and tissue-nonspecific alkaline phosphatase, was upregulated in OA chondrocytes isolated from CaC crystal-containing cartilages. CONCLUSIONS: CaC crystal deposition is a widespread phenomenon in human OA articular cartilage involving the entire knee cartilage including macroscopically normal and less weight-bearing zones. Cartilage calcification is associated with altered expression of genes involved in the mineralisation process.

Ponctions et infiltrations articulaires [Arthrocentesis and joint infiltration]

Cet article se veut être un condensé des bases nécessaires à la pratique d'une ponction et, ou infiltration articulaire, des indications principales aux complications potentielles en passant par la description de la procédure et de ses contre-indications. La ponction du genou fait l'objet d'une description plus détaillée. Les données permettant de justifier une façon particulière de procéder ont spécifiquement été recherchées dans la littérature (Cochrane et Medline, termes de recherche : arthrocentesis ; joint aspiration). Le détail de ces données, comme par exemple le résultat d'études, ne trouve pas sa place dans ce résumé mais fait l'objet d'une publication à part. What should be known in order to practice safely a joint aspiration and/or infiltration is summarized in the following article. This summary includes various aspects, such as the indications and contraindications, the procedure itself, and the possible complications. The arthrocentesis of the knee is described in more details. Data in support of a specific modus operandi have been searched for in Cochrane and Pubmed (key words: arthrocentesis, joint aspiration). Only the conclusions of this research are exposed in this summary. A more comprehensive article will be published

Chirurgie du pied et de la cheville rhumatoïdes [Surgery of the rheumatoid foot and ankle]

Surgery of the rheumatoid foot and ankle Initial presentation of rheumatoid arthritis (RA) will be foot and ankle symptoms in 20% of cases. Eventually, 50-90% of patients will develop foot and ankle alterations. Typical deformities of the forefoot include hallux valgus and dorso-lateral dislocation of the lesser metatarso-phalangeal joints. RA involvement of the hindfoot frequently leads to plano-valgus deformity. Approximately 20% of surgery performed for RA is done at the foot and ankle. Early surgery is efficient against pain and deformity. Patient's satisfaction rate after surgery is high despite a slight higher complication rate compared to conventional foot and ankle surgery.

Cracking and Seating PCC Pavement Prior to Resurfacing, HR-527, 1986

Construction of an excellent network of primary highways across the State of Iowa has essentially been completed. The major task facing the Iowa Department of Transportation today is the maintenance and rehabilitation of that network. The most commonly utilized rehabilitation practice is asphalt concrete resurfacing. This practice will normally provide a good driving surface for at least 10 additional years. The major problem with asphalt concrete resurfacing is the reflection cracking from underlying cracks and joints in the portland cement concrete (PCC) pavement. Deterioration and spaling occur at these reflection cracks and are the limiting factor of the-effective life of the asphalt concrete resurfacing.

Laboratory Investigation of Bridge Strip Seal Joint Termination Details, SPR RB08-014, 2016

Bridge expansion joints, if not properly designed, constructed, and maintained, often lead to the deterioration of critical substructure elements. Strip seal expansion joints consisting of a steel extrusion and neoprene gland are one type of expansion joint and are commonly used by the Iowa Department of Transportation (DOT). Strip seal expansion joints are susceptible to tears and pull outs that allow water, chlorides, and debris to infiltrate the joint, and subsequently the bearings below. One area of the strip seal that is particularly problematic is where it terminates at the interface between the deck and the barrier rail. The Iowa DOT has noted that the initial construction quality of the current strip seal termination detail is not satisfactory, nor ideal, and a need exists for re-evaluation and possibly re-design of this detail. Desirable qualities of a strip seal termination detail provide a seal that is simple and fast to construct, facilitate quick gland removal and installation, and provide a reliable, durable barrier to prevent chloride-contaminated water from reaching the substructure. To meet the objectives of this research project, several strip seal termination details were evaluated in the laboratory. Alternate termination details may not only function better than the current Iowa DOT standard, but are also less complicated to construct, facilitating better quality control. However, uncertainties still exist regarding the long-term effects of using straight-through details, with or without the dogleg, that could not be answered in the laboratory in the short time frame of the research project.

Field Evaluation of Cold In-Place Recycling of Asphalt Concrete, HR-303, Construction Report, 1990

There are still many vintage portland cement concrete (PCC) pavements, 18 ft wide (5.4 m), dating back to pre-World War II era in use today. Successive overlays have been placed to cover joints and to improve rideability. The average thickness of the existing asphalt cement concrete (ACC) along route E66 in Tama County, Iowa, was 6.13 in. (15.6 cm). The rehabilitation strategy called for widening the base using the top 3 in. (7.6 cm) of the existing ACC by a recycling process involving cold milling and mixing with additional emulsion/rejuvenator. The material was then placed into a widening trench and compacted to match the level of the milled surface. This project was undertaken to develop a rehabilitation methodology to widen these older pavements economically and to have a finished surface capable of carrying traffic with little or no additional work.

Adding tobacco to cannabis: its frequency and likely implications.

INTRODUCTION: Young cannabis users are at increased risk of later cigarette initiation and progression to nicotine addiction. The present study addresses the frequency at which mulling (adding tobacco to cannabis smoked as joints) is performed and in which way this practice varies according to cigarette smoking status. METHODS: Data were issued from the Swiss 2007 European School Survey Project on Alcohol and other Drugs (ESPAD). A total of 881 past month cannabis users (mean age 15 years, boys 60.1%) were inquired on mulling using an anonymous self-administered questionnaire. Participants were further grouped according to their cigarette smoking status (daily, occasional, former, and never-smokers). RESULTS: Four of every 5 cannabis users depicted mulling as frequently performed. The highest occurrence was found among daily cigarette smokers (DSC; 90.3%), while former cigarette smokers reported the lowest (58.9%). The multinomial logistic regression showed DSC more likely reporting mulling as frequent compared with never-smokers (risk ratio = 3.56 [95% CI 1.55-8.21]). Conclusions: Mulling appears to be a very common process among young cannabis users, especially among concomitant cigarette smokers. Nevertheless, the majority of cigarette abstainers also reported frequently adding tobacco to the cannabis they smoke. Because it may represent a significant exposition to nicotine, mulling should be taken into account when assessing substance use among adolescents and in supporting their quitting attempts.

Mutations in the TGFβ binding-protein-like domain 5 of FBN1 are responsible for acromicric and geleophysic dysplasias.

Geleophysic (GD) and acromicric dysplasia (AD) belong to the acromelic dysplasia group and are both characterized by severe short stature, short extremities, and stiff joints. Although AD has an unknown molecular basis, we have previously identified ADAMTSL2 mutations in a subset of GD patients. After exome sequencing in GD and AD cases, we selected fibrillin 1 (FBN1) as a candidate gene, even though mutations in this gene have been described in Marfan syndrome, which is characterized by tall stature and arachnodactyly. We identified 16 heterozygous FBN1 mutations that are all located in exons 41 and 42 and encode TGFβ-binding protein-like domain 5 (TB5) of FBN1 in 29 GD and AD cases. Microfibrillar network disorganization and enhanced TGFβ signaling were consistent features in GD and AD fibroblasts. Importantly, a direct interaction between ADAMTSL2 and FBN1 was demonstrated, suggesting a disruption of this interaction as the underlying mechanism of GD and AD phenotypes. Although enhanced TGFβ signaling caused by FBN1 mutations can trigger either Marfan syndrome or GD and AD, our findings support the fact that TB5 mutations in FBN1 are responsible for short stature phenotypes.

Comparison of cannabinoid concentrations in oral fluid and whole blood between occasional and regular cannabis smokers prior to and after smoking a cannabis joint.

A cross-over controlled administration study of smoked cannabis was carried out on occasional and heavy smokers. The participants smoked a joint (11 % Δ9-tetrahydrocannabinol (THC)) or a matching placebo on two different occasions. Whole blood (WB) and oral fluid (OF) samples were collected before and up to 3.5 h after smoking the joints. Pharmacokinetic analyses were obtained from these data. Questionnaires assessing the subjective effects were administered to the subjects during each session before and after the smoking time period. THC, 11-hydroxy-THC (11-OH-THC) and 11-nor-9-carboxy-THC (THCCOOH) were analyzed in the blood by gas chromatography or liquid chromatography (LC)-tandem mass spectrometry (MS/MS). The determination of THC, THCCOOH, cannabinol (CBN), and Δ9-tetrahydrocannabinolic acid A (THC-A) was carried out on OF only using LC-MS/MS. In line with the widely accepted assumption that cannabis smoking results in a strong contamination of the oral cavity, we found that THC, and also THC-A, shows a sharp, high concentration peak just after smoking, with a rapid decrease in these levels within 3 h. No obvious differences were found between both groups concerning THC median maximum concentrations measured either in blood or in OF; these levels were equal to 1,338 and 1,041 μg/L in OF and to 82 and 94 μg/L in WB for occasional and heavy smokers, respectively. The initial WB THCCOOH concentration was much higher in regular smokers than in occasional users. Compared with the occasional smokers, the sensation of confusion felt by the regular smokers was much less while the feeling of intoxication remained almost unchanged.

Cinema and the Work of Doré

According to Ray Harryhausen, a special effects expert in the film industry, "Gustave Doré would have made a great director of photography . . . He saw things from the point of view of the camera." Doré's work has had a permanent impact on the imaginative realm of film since its very early days. In return, the silver screen has etched Doré into the 20th century imagination. Almost every film about the Bible since The Life and Passion of Jesus Christ produced by Pathé in 1902 refers to his illustrations, and every film adaptation of Dante or Don Quixote has used him as a model, from Georg Wilhelm Pabst and Orson Welles to Terry Gilliam. All films dealing with life in London in the Victorian era by directors ranging from David Lean, to Roman Polanski and Tim Burton draw on the visions in London: a pilgrimage for their sets. A large number of dream fantastical or phantasmagorical scenes take their inspiration from Doré's graphic world, beginning with Georges Méliès' A Trip to the Moon in 1902. In the realm of cartoons and animation, Walt Disney owes a huge debt to Doré. Doré primal forests, from Atala in particular, were also used in the various versions of King Kong from 1933 to the 2005 film by Peter Jackson, who had already drawn on Doré for The Lord of the Rings. Jean Cocteau was also indebted to the illustrations for Perrault's Fairy Tales for his Beauty and the Beast (1945), as was George Lucas for the character Chewbacca in Star Wars (1977) and even the Harry Potter film series. Through his influence on film history, Doré shaped the mass culture imagination.