Qualitative SEM/EDS analysis of microleakage and apical gap formation of adhesive root-filling materials

Objective: The aim of this study was to compare the correspondence between gap formation and apical microleakage in root canals filled with epoxy resin-based (AH Plus) combined or not with resinous primer or with a dimethacrylate-based root canal sealer (Epiphany). Material and Methods: Thirty-nine lower single-rooted human premolars were filled by the lateral condensation technique (LC) and immersed in a 50-wt% aqueous silver nitrate solution at 37 degrees C (24 h). After longitudinal sectioning, epoxy resin replicas were made from the tooth specimens. Both the replicas and the specimens were prepared for scanning electron microscopy (SEM). The gaps were observed in the replicas. Apical microleakage was detected in the specimens by SEM/energy dispersive spectroscopy (SEM/EDS). The data were analyzed statistically using an Ordinal Logistic Regression model and Analysis of Correspondence (alpha=0.05). Results: Epiphany presented more regions containing gaps between dentin and sealer (p<0.05). There was correspondence between the presence of gaps and microleakage (p<0.05). Microleakage was similar among the root-filling materials (p>0.05). Conclusions: The resinous primer did not improve the sealing ability of AH Plus sealer and the presence of gaps had an effect on apical microleakage for all materials.

Analysis of confinement potential fluctuation and band-gap renormalization effects on excitonic transition in GaAs/AlGaAs multiquantum wells grown on (100) and (311)A GaAs surfaces

The competition between confinement potential fluctuations and band-gap renormalization (BGR) in GaAs/AlxGa1-xAs quantum wells grown on [1 0 0] and [3 1 1]A GaAs substrates is evaluated. The results clearly demonstrate the coexistence of the band-tail states filling related to potential fluctuations and the band-gap renormalization caused by an increase in the density of photogenerated carriers during the photoluminescence (PL) experiments. Both phenomena have strong influence on temperature dependence of the PL-peak energy (E-PL(T)). As the photon density increases, the E-PL can shift to either higher or lower energies, depending on the sample temperature. The temperature at which the displacement changes from a blueshift to a redshift is governed by the magnitude of the potential fluctuations and by the variation of BGR with excitation density. A simple band-tail model with a Gaussian-like distribution of the density of state was used to describe the competition between the band-tail filling and the BGR effects on E-PL(T). (C) 2012 Elsevier B.V. All rights reserved.

Air pollution and health: bridging the gap from sources to health outcomes: conference summary

Air Pollution and Health: Bridging the Gap from Sources to Health Outcomes, an international specialty conference sponsored by the American Association for Aerosol Research, was held to address key uncertainties in our understanding of adverse health effects related to air pollution and to integrate and disseminate results from recent scientific studies that cut across a range of air pollution-related disciplines. The Conference addressed the science of air pollution and health within a multipollutant framework (herein "multipollutant" refers to gases and particulate matter mass, components, and physical properties), focusing on five key science areas: sources, atmospheric sciences, exposure, dose, and health effects. Eight key policy-relevant science questions integrated across various parts of the five science areas and a ninth question regarding findings that provide policy-relevant insights served as the framework for the meeting. Results synthesized from this Conference provide new evidence, reaffirm past findings, and offer guidance for future research efforts that will continue to incrementally advance the science required for reducing uncertainties in linking sources, air pollutants, human exposure, and health effects. This paper summarizes the Conference findings organized around the science questions. A number of key points emerged from the Conference findings. First, there is a need for greater focus on multipollutant science and management approaches that include more direct studies of the mixture of pollutants from sources with an emphasis on health studies at ambient concentrations. Further, a number of research groups reaffirmed a need for better understanding of biological mechanisms and apparent associations of various health effects with components of particulate matter (PM), such as elemental carbon, certain organic species, ultrafine particles, and certain trace elements such as Ni, V, and Fe(II), as well as some gaseous pollutants. Although much debate continues in this area, generation of reactive oxygen species induced by these and other species present in air pollution and the resulting oxidative stress and inflammation were reiterated as key pathways leading to respiratory and cardiovascular outcomes. The Conference also underscored significant advances in understanding the susceptibility of populations, including the role of genetics and epigenetics and the influence of socioeconomic and other confounding factors and their synergistic interactions with air pollutants. Participants also pointed out that short-and long-term intervention episodes that reduce pollution from sources and improve air quality continue to indicate that when pollution decreases so do reported adverse health effects. In the limited number of cases where specific sources or PM2.5 species were included in investigations, specific species are often associated with the decrease in effects. Other recent advances for improved exposure estimates for epidemiological studies included using new technologies such as microsensors combined with cell phone and integrated into real-time communications, hybrid air quality modeling such as combined receptor-and emission-based models, and surface observations used with remote sensing such as satellite data.

GaMnAs: Position of Mn-d levels and majority spin band gap predicted from GGA-1/2 calculations

Among all magnetic semiconductors, GaMnAs seems to be the most important one. In this work, we present accurate first-principles calculations of GaMnAs within the GGA-1/2 approach: We concentrate our efforts in obtaining the position of the peak of Mn-d levels in the valence band and also the majority spin band gap. For the position of the Mn-d peak, we find a value of 3.3 eV below the Fermi level, in good agreement with the most recent experimental results of 3.5 and 3.7 eV. An analytical expression that fits the calculated E-g(x) for majority spin is derived in order to provide ready access to the band gap for the composition range from 0 to 0.25. We found a value of 3.9 eV for the gap bowing parameter. The results agree well with the most recent experimental data. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4718602]

Poli (metil azoteto de glicidila) - GAP. I: síntese e caracterização

O poli (metil azoteto de glicidila) - GAP - é um material energético que pode ser utilizado como aglutinante (binder) e como plastificante energético em compostos explosivos e propulsores de foguetes. Neste trabalho, foi abordada a síntese do (GAP) através da conversão direta da epicloridrina (ECH) a GAP. Os reagentes utilizados foram azida de sódio, epicloridrina e vários álcoois extensores de cadeias, o etanodiol, o 1,4-butanodiol, o dietilenoglicol e o glicerol. Alguns parâmetros de operação foram avaliados, como o tempo de reação, a proporção entre os reagentes, dois tipos de solvente e a ordem de adição dos reagentes. A variável observada para a análise foi a massa molecular do GAP. Todos os materiais sintetizados também foram caracterizados por análises de FTIR, UV, RMN, DSC, análise elementar e TGA. Uma maior massa molecular, maior rendimento e uma melhor conversão do grupo azida a GAP foram obtidos com a adição de epicloridrina sobre a azida de sódio e usando DMF como solvente.

Poli (metil azoteto de glicidila) - GAP. II: mecanismo de reação

O poli (metil azoteto de glicidila) - GAP - é um material energético que pode ser utilizado como aglutinante (binder) e como plastificante energético em compostos explosivos e propulsores de foguetes. O GAP de baixo peso molecular pode ser obtido pela conversão direta da epicloridrina (ECH) a GAP. Neste trabalho, é proposto um possível mecanismo para esta conversão direta, fundamentado em análises de infravermelho de espécies intermediárias.

Narrowing the gap of personalized medicine in emerging countries: the case of multiple endocrine neoplasias in Brazil

The finished version of the human genome sequence was completed in 2003, and this event initiated a revolution in medical practice, which is usually referred to as the age of genomic or personalized medicine. Genomic medicine aims to be predictive, personalized, preventive, and also participative (4Ps). It offers a new approach to several pathological conditions, although its impact so far has been more evident in mendelian diseases. This article briefly reviews the potential advantages of this approach, and also some issues that may arise in the attempt to apply the accumulated knowledge from genomic medicine to clinical practice in emerging countries. The advantages of applying genomic medicine into clinical practice are obvious, enabling prediction, prevention, and early diagnosis and treatment of several genetic disorders. However, there are also some issues, such as those related to: (a) the need for approval of a law equivalent to the Genetic Information Nondiscrimination Act, which was approved in 2008 in the USA; (b) the need for private and public funding for genetics and genomics; (c) the need for development of innovative healthcare systems that may substantially cut costs (e.g. costs of periodic medical followup); (d) the need for new graduate and postgraduate curricula in which genomic medicine is emphasized; and (e) the need to adequately inform the population and possible consumers of genetic testing, with reference to the basic aspects of genomic medicine.

Are prescribing doctors sensitive to the price that their patients have to pay in the Spanish National Health System?

[EN] Background This study aims to design an empirical test on the sensitivity of the prescribing doctors to the price afforded for the patient, and to apply it to the population data of primary care dispensations for cardiovascular disease and mental illness in the Spanish National Health System (NHS). Implications for drug policies are discussed. Methods We used population data of 17 therapeutic groups of cardiovascular and mental illness drugs aggregated by health areas to obtain 1424 observations ((8 cardiovascular groups * 70 areas) + (9 psychotropics groups * 96 areas)). All drugs are free for pensioners. For non-pensioner patients 10 of the 17 therapeutic groups have a reduced copayment (RC) status of only 10% of the price with a ceiling of €2.64 per pack, while the remaining 7 groups have a full copayment (FC) rate of 40%. Differences in the average price among dispensations for pensioners and non-pensioners were modelled with multilevel regression models to test the following hypothesis: 1) in FC drugs there is a significant positive difference between the average prices of drugs prescribed to pensioners and non-pensioners; 2) in RC drugs there is no significant price differential between pensioner and non-pensioner patients; 3) the price differential of FC drugs prescribed to pensioners and non-pensioners is greater the higher the price of the drugs. Results The average monthly price of dispensations to pensioners and non-pensioners does not differ for RC drugs, but for FC drugs pensioners get more expensive dispensations than non-pensioners (estimated difference of €9.74 by DDD and month). There is a positive and significant effect of the drug price on the differential price between pensioners and non-pensioners. For FC drugs, each additional euro of the drug price increases the differential by nearly half a euro (0.492). We did not find any significant differences in the intensity of the price effect among FC therapeutic groups. Conclusions Doctors working in the Spanish NHS seem to be sensitive to the price that can be afforded by patients when they fill in prescriptions, although alternative hypothesis could also explain the results found.

Study of silicon-on-insulator multiple-gate MOS structures including band-gap engineering and self heating effects

The progresses of electron devices integration have proceeded for more than 40 years following the well–known Moore’s law, which states that the transistors density on chip doubles every 24 months. This trend has been possible due to the downsizing of the MOSFET dimensions (scaling); however, new issues and new challenges are arising, and the conventional ”bulk” architecture is becoming inadequate in order to face them. In order to overcome the limitations related to conventional structures, the researchers community is preparing different solutions, that need to be assessed. Possible solutions currently under scrutiny are represented by: • devices incorporating materials with properties different from those of silicon, for the channel and the source/drain regions; • new architectures as Silicon–On–Insulator (SOI) transistors: the body thickness of Ultra-Thin-Body SOI devices is a new design parameter, and it permits to keep under control Short–Channel–Effects without adopting high doping level in the channel. Among the solutions proposed in order to overcome the difficulties related to scaling, we can highlight heterojunctions at the channel edge, obtained by adopting for the source/drain regions materials with band–gap different from that of the channel material. This solution allows to increase the injection velocity of the particles travelling from the source into the channel, and therefore increase the performance of the transistor in terms of provided drain current. The first part of this thesis work addresses the use of heterojunctions in SOI transistors: chapter 3 outlines the basics of the heterojunctions theory and the adoption of such approach in older technologies as the heterojunction–bipolar–transistors; moreover the modifications introduced in the Monte Carlo code in order to simulate conduction band discontinuities are described, and the simulations performed on unidimensional simplified structures in order to validate them as well. Chapter 4 presents the results obtained from the Monte Carlo simulations performed on double–gate SOI transistors featuring conduction band offsets between the source and drain regions and the channel. In particular, attention has been focused on the drain current and to internal quantities as inversion charge, potential energy and carrier velocities. Both graded and abrupt discontinuities have been considered. The scaling of devices dimensions and the adoption of innovative architectures have consequences on the power dissipation as well. In SOI technologies the channel is thermally insulated from the underlying substrate by a SiO2 buried–oxide layer; this SiO2 layer features a thermal conductivity that is two orders of magnitude lower than the silicon one, and it impedes the dissipation of the heat generated in the active region. Moreover, the thermal conductivity of thin semiconductor films is much lower than that of silicon bulk, due to phonon confinement and boundary scattering. All these aspects cause severe self–heating effects, that detrimentally impact the carrier mobility and therefore the saturation drive current for high–performance transistors; as a consequence, thermal device design is becoming a fundamental part of integrated circuit engineering. The second part of this thesis discusses the problem of self–heating in SOI transistors. Chapter 5 describes the causes of heat generation and dissipation in SOI devices, and it provides a brief overview on the methods that have been proposed in order to model these phenomena. In order to understand how this problem impacts the performance of different SOI architectures, three–dimensional electro–thermal simulations have been applied to the analysis of SHE in planar single and double–gate SOI transistors as well as FinFET, featuring the same isothermal electrical characteristics. In chapter 6 the same simulation approach is extensively employed to study the impact of SHE on the performance of a FinFET representative of the high–performance transistor of the 45 nm technology node. Its effects on the ON–current, the maximum temperatures reached inside the device and the thermal resistance associated to the device itself, as well as the dependence of SHE on the main geometrical parameters have been analyzed. Furthermore, the consequences on self–heating of technological solutions such as raised S/D extensions regions or reduction of fin height are explored as well. Finally, conclusions are drawn in chapter 7.

Untersuchungen von intrazellulären Signalwegen bei neuraler Determinierung und Differenzierung in vitro: Einfluß von GAP-43 und Bcl-2

Die PCC7-Mz1-Zellinie stellt ein geeignetes Modell dar, um frühe neurale Determinierungs- und Differenzierungsprozesse unter kontrollierten Bedingungen in vitro zu untersuchen. Aus pluripotenten Stammzellen entwickelt sich nach Behandlung mit dem Morphogen Retinsäure (RA) ein stabiles Muster aus Neuronen, Fibroblasten und Astroglia-Zellen. Parallel stirbt ein reproduzierbarer Anteil der Kultur apoptotisch. Zur näheren Aufklärung der molekularen Vorgänge während der neuralen Entwicklung wurde der Einfluß von zwei Schlüsselmolekülen - dem Proteinkinase C Substrat (PKC) GAP-43 sowie dem antiapoptotischen Bcl-2 Protein - auf die neurale Differenzierung und die damit assoziierten Apoptoseereignisse der PCC7-Mz1-Zellen untersucht. Dazu wurden stabile Zellinien, die eine Überexpression von GAP-43 bzw. von Bcl-2 aufwiesen, hergestellt. GAP-43In PCC7-Mz1-Zellen wurde die Expression von GAP-43 sowohl auf mRNA- als auch auf Protein-Ebene innerhalb von 24 Stunden nach Zugabe von RA hochreguliert. GAP-43 war bereits in noch proliferierenden neuronalen Vorläuferzellen als Substrat für PKC und als Interaktionspartner von Calmodulin funktionell. Die Überexpression von GAP-43 in PCC7-Mz1-Zellen förderte die Ausprägung des neuronalen Phänotyps. Das Differenzierungspotential der Mz-GAP-43 Klone war eingeschränkt, da sich nach Induktion mit RA aus den Stammzellen nur noch Neurone, aber keine Fibroblasten und Astroglia-Zellen mehr entwickelten. Die Determinierung für das neuronale Entwicklungsschicksal war in den Mz-GAP-43 Klonen stärker fortgeschritten als in MzN-Klonen, die durch Subklonierung aus PCC7-Mz1-Zellen generiert wurden, da die GAP-43 überexprimierenden Zellen durch Wachstum auf Laminin nicht in den pluripotenten Phänotyp revertiert werden konnten. Aufgrund der Interaktion zwischen GAP-43 und Calmodulin in Stammzellen der Mz-GAP-43 Klone kann man vermuten, daß die neuronalen Determinierungsprozesse über Ca2+/Calmodulin-abhängige Signalwege verlaufen. Da das Gen für den Transkriptionsfaktor NCNF (

Sistemi riconfigurabili a basso consumo per applicazioni di monitoraggio distribuito

The term Ambient Intelligence (AmI) refers to a vision on the future of the information society where smart, electronic environment are sensitive and responsive to the presence of people and their activities (Context awareness). In an ambient intelligence world, devices work in concert to support people in carrying out their everyday life activities, tasks and rituals in an easy, natural way using information and intelligence that is hidden in the network connecting these devices. This promotes the creation of pervasive environments improving the quality of life of the occupants and enhancing the human experience. AmI stems from the convergence of three key technologies: ubiquitous computing, ubiquitous communication and natural interfaces. Ambient intelligent systems are heterogeneous and require an excellent cooperation between several hardware/software technologies and disciplines, including signal processing, networking and protocols, embedded systems, information management, and distributed algorithms. Since a large amount of fixed and mobile sensors embedded is deployed into the environment, the Wireless Sensor Networks is one of the most relevant enabling technologies for AmI. WSN are complex systems made up of a number of sensor nodes which can be deployed in a target area to sense physical phenomena and communicate with other nodes and base stations. These simple devices typically embed a low power computational unit (microcontrollers, FPGAs etc.), a wireless communication unit, one or more sensors and a some form of energy supply (either batteries or energy scavenger modules). WNS promises of revolutionizing the interactions between the real physical worlds and human beings. Low-cost, low-computational power, low energy consumption and small size are characteristics that must be taken into consideration when designing and dealing with WSNs. To fully exploit the potential of distributed sensing approaches, a set of challengesmust be addressed. Sensor nodes are inherently resource-constrained systems with very low power consumption and small size requirements which enables than to reduce the interference on the physical phenomena sensed and to allow easy and low-cost deployment. They have limited processing speed,storage capacity and communication bandwidth that must be efficiently used to increase the degree of local ”understanding” of the observed phenomena. A particular case of sensor nodes are video sensors. This topic holds strong interest for a wide range of contexts such as military, security, robotics and most recently consumer applications. Vision sensors are extremely effective for medium to long-range sensing because vision provides rich information to human operators. However, image sensors generate a huge amount of data, whichmust be heavily processed before it is transmitted due to the scarce bandwidth capability of radio interfaces. In particular, in video-surveillance, it has been shown that source-side compression is mandatory due to limited bandwidth and delay constraints. Moreover, there is an ample opportunity for performing higher-level processing functions, such as object recognition that has the potential to drastically reduce the required bandwidth (e.g. by transmitting compressed images only when something ‘interesting‘ is detected). The energy cost of image processing must however be carefully minimized. Imaging could play and plays an important role in sensing devices for ambient intelligence. Computer vision can for instance be used for recognising persons and objects and recognising behaviour such as illness and rioting. Having a wireless camera as a camera mote opens the way for distributed scene analysis. More eyes see more than one and a camera system that can observe a scene from multiple directions would be able to overcome occlusion problems and could describe objects in their true 3D appearance. In real-time, these approaches are a recently opened field of research. In this thesis we pay attention to the realities of hardware/software technologies and the design needed to realize systems for distributed monitoring, attempting to propose solutions on open issues and filling the gap between AmI scenarios and hardware reality. The physical implementation of an individual wireless node is constrained by three important metrics which are outlined below. Despite that the design of the sensor network and its sensor nodes is strictly application dependent, a number of constraints should almost always be considered. Among them: • Small form factor to reduce nodes intrusiveness. • Low power consumption to reduce battery size and to extend nodes lifetime. • Low cost for a widespread diffusion. These limitations typically result in the adoption of low power, low cost devices such as low powermicrocontrollers with few kilobytes of RAMand tenth of kilobytes of program memory with whomonly simple data processing algorithms can be implemented. However the overall computational power of the WNS can be very large since the network presents a high degree of parallelism that can be exploited through the adoption of ad-hoc techniques. Furthermore through the fusion of information from the dense mesh of sensors even complex phenomena can be monitored. In this dissertation we present our results in building several AmI applications suitable for a WSN implementation. The work can be divided into two main areas:Low Power Video Sensor Node and Video Processing Alghoritm and Multimodal Surveillance . Low Power Video Sensor Nodes and Video Processing Alghoritms In comparison to scalar sensors, such as temperature, pressure, humidity, velocity, and acceleration sensors, vision sensors generate much higher bandwidth data due to the two-dimensional nature of their pixel array. We have tackled all the constraints listed above and have proposed solutions to overcome the current WSNlimits for Video sensor node. We have designed and developed wireless video sensor nodes focusing on the small size and the flexibility of reuse in different applications. The video nodes target a different design point: the portability (on-board power supply, wireless communication), a scanty power budget (500mW),while still providing a prominent level of intelligence, namely sophisticated classification algorithmand high level of reconfigurability. We developed two different video sensor node: The device architecture of the first one is based on a low-cost low-power FPGA+microcontroller system-on-chip. The second one is based on ARM9 processor. Both systems designed within the above mentioned power envelope could operate in a continuous fashion with Li-Polymer battery pack and solar panel. Novel low power low cost video sensor nodes which, in contrast to sensors that just watch the world, are capable of comprehending the perceived information in order to interpret it locally, are presented. Featuring such intelligence, these nodes would be able to cope with such tasks as recognition of unattended bags in airports, persons carrying potentially dangerous objects, etc.,which normally require a human operator. Vision algorithms for object detection, acquisition like human detection with Support Vector Machine (SVM) classification and abandoned/removed object detection are implemented, described and illustrated on real world data. Multimodal surveillance: In several setup the use of wired video cameras may not be possible. For this reason building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. Energy efficiency for wireless smart camera networks is one of the major efforts in distributed monitoring and surveillance community. For this reason, building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. The Pyroelectric Infra-Red (PIR) sensors have been used to extend the lifetime of a solar-powered video sensor node by providing an energy level dependent trigger to the video camera and the wireless module. Such approach has shown to be able to extend node lifetime and possibly result in continuous operation of the node.Being low-cost, passive (thus low-power) and presenting a limited form factor, PIR sensors are well suited for WSN applications. Moreover techniques to have aggressive power management policies are essential for achieving long-termoperating on standalone distributed cameras needed to improve the power consumption. We have used an adaptive controller like Model Predictive Control (MPC) to help the system to improve the performances outperforming naive power management policies.

In Between : The Gap of quality L'influenza dell'insegnamento di Gurdjieff nel teatro di Peter Brook, Decalan Donnellan e Robert Lepage

Il Lavoro é incentrato sull' influenza dell'insegnamento di G. I Gurdjieff sul teatro del novecento in particolare sul lavoro di Peter Brook, Declan Donnellan e Robert Lepage

Fresh Produce Safety and Good Agricultural Practices: Stakeholders' Perception and Consumers' Choice in Thailand

Concerns of Thai consumers on food safety have been recently increasing, especially in urban areas and for fresh produce because food safety scandals, such as chemical residues on fresh produce (e.g., cabbage) still frequently occur. The Thai government tried to meet consumer needs by imposing in the domestic market a stronger regulation aimed at increasing the baseline level of food safety assurance and by introducing a voluntary standard (based on Good Agricultural Practices or GAPs and known as Q-GAP) and the related food safety label (i.e., Q mark). However, since standards and regulations are weakly implemented in the domestic market compared to exported products, there is still a lack of Thai consumers’ confidence in the safety of local food products. In this work the current situation of GAPs adoption in Thai fresh produce production is analysed. Furthermore, it is studied whether Thai consumers place value on food safety labels available on the market, to know whether consumer demand could drive the market of certified safer products. This study contains three essays: 1) a review of the literature, 2) a qualitative study on stakeholders' perception toward GAPs adoption and 3) a quantitative study, aimed at analysing consumers' preferences and willingness-to-pay for food safety labels on fresh produce using a discrete choice experiment. This dissertation contributes to the economics of quality assurance and labelling, specifically addressing GAPs and food safety label in the fresh produce supply chain. Results show that Q-GAP could be effectively used to improve food safety in Thai domestic market, but its credibility should be improved. Stakeholder’s awareness toward food safety issues and the delivery of reliable and sound information are crucial. Thai consumers are willing to pay a premium price for food safety labelled produce over unlabelled ones. Implications for both government and business decision-makers are discussed.