Características da pulverização produzida por pontas Yamaho da série 'D'

This study evaluated the characteristics of spray produced by Yamaho nozzle tip'D'series. The droplet size of nozzle tips D3, D4, D5, D6 and D8 were evaluated at 703, 1.050, 1.406, 1.758, 2.110, 2.461 e 2.813 kPa pressures (100, 200, 250; 350, e 400 psi) by means of laser equipment, as well as the flow rate of nozzle tip at the pressures of 702, 1.125, 1.406, 1.828, 2.110, 2.532 e 2.813 kPa (100, 160, 200, 260,300; 360 e 400 psi) which were compared with values indicated by manufacturer. The droplet produced at all pressures presented a very fine spray, which in agriculture may promote losses by evaporation and drift. For all nozzle tips, except D8 in pressures 1.828, 2.532 e 2.813 kPa, the difference between the observed flow rate indicated by the manufacturer was higher than 5%. The paper demonstrates that the nozzle tip tested, in spite of not having uniform flow rate, may promote the contamination of spray operator and environment due to the droplet spectrum produced.

Nanostructured films of perylene derivatives: High performance materials for taste sensor applications

Four perylene derivatives (PTCD) have been used as transducing materials in taste sensors fabricated with nanostructured Langmuir-Blodgett (LB) films deposited onto interdigitated gold electrodes. The Langmuir monolayers of PTCDs display considerable collapse pressures, with areas per molecule indicative of an edge-on or head-on arrangement for the molecules at the air/water interface. The sensing units for the electronic tongue were produced from 5-layer LB films of the four PTCDs, whose electrical response was characterized with impedance spectroscopy. The distinct responses of the PTCDs, attributed to differences in their molecular structures, allowed one to obtain a finger printing system that was able to distinguish tastes (salty, sweet, bitter and sour) at 1 μM concentrations, which, in some cases, are three orders of magnitude below the human threshold. Using Principal Component Analysis (PCA) data analysis, the electronic tongue also detected trace amounts of a pesticide and could distinguish among samples of ultrapure, distilled and tap water, and two brands of mineral water. © 2004 by American Scientific Publishers. All rights reserved.

Pollution by hexachlorobenzene and pentachlorophenol in the coastal plain of São Paulo state, Brazil

Organochlorine compounds were dumped by chemical industries during the 1970s in many areas of the coastal plain of São Paulo state in Brazil. These dumps, located on hillsides and in valleys, in both rural and urban environments, are responsible for soil and water pollution. The objective of this work was to determine how the pollutants have spread in an area occupied by a spodosol-type soil mantle. The study combines soil morphological observations with soil and water analysis of hexachlorobenzene (HCB) and pentachlorophenol (PCP) in soil toposequences. The results indicate that the highest pollutant concentrations are observed near the dump site and that the compounds contamination is increasing. A map integrating topography and chemical concentrations was created to visualize the spatial distribution of HCB levels in the landscape. Physical and chemical analyses were performed to measure HCB and PCP levels in the soil. Soil water appears to act as a vector of HCB, probably through complexation with and dispersal of dissolved organic matter. The persistence of HCB at the studied site is most likely due to the low pH values in combination with a high content of organic matter. HCB was consistently found in higher concentrations than PCP. It is plausible that the cause of this difference is that PCP is degraded more easily under sunlight than HCB and that degradation of PCP under acid conditions leads to the formation of HCB. © 2003 Published by Elsevier B.V.

Neonatal rat exposure to pyrethroid and organophosphate insecticides: A physiological and biochemical trial of progeny

A manufactured product (Ectoplus®) composed by a cypermethrin (44.7%) and dichlorvos (4.2%) mixture was administered (10mg/kg/day, orally, by gavage) to pregnant rats, during the periods of gestation+lactation, gestation, and lactation. Control mothers received vehicle aqueous solution during the gestation+lactation period. With the progeny, in the 1-15 post-natal days (PNDI-15) there were observed alterations in the periods of occurrence of teeth, hair, unfolding of ears, and in the developmental period for following reflexes: postural, palmar grasp, negative geotaxis, and acoustic startle reflex. After weaning (PND21), there were observed the presence of cypermethrin and dichlorvos in the blood brain and liver; decrease in weight of liver, of cholinesterase activity in the plasma, liver, and brain, and hepatic metabolizing activity of drugs; alterations of levels of gamma glutamyl transferase enzymes, of creatinine, and of potassium in the serum of the animals. In conclusion, neonatal exposure to a formulated mixture of cypermethrin and dichlorvos is inductive to alterations in characteristics that indicate somatic and neuromuscular development of the progeny, and in certain biochemical parameters. The results suggest that enzymatic assessment associated with somatic and neuromotor assessment can be important markers of developmental characteristics in neonatal toxicity by pesticide formulations based on mixtures of insecticides.

Importância da linha de base pré-exposição das colinesterases (ChEs) no controle ocupacional a praguicidas organofosforados e carbamatos

The most immediate toxic effects of a poisoning for organophosphate or carbamate are promoted by inhibition of cholinesterases (ChEs). However, a serious limitation to the diagnosis of mild organophosphate or carbamate poisoning and to preventive screening of organophosphate-exposed workers has been the large interindividual variability in ChEs activity. This makes it necessary to obtain a pre-exposure baseline measurement of enzyme activity as a basis for evaluating subsequent declines. Thus, the objective of this work is demonstrate the value of the pre-exposure baseline in the interpretation of the results of the ChEs activity of the carbamate or organophosphate-exposed workers. Using Nabb & Whitfield (1967) method to analyze blood of 48 workers the results have shown a erythrocyte cholinesterase range of 10.1 to 19.7 μmol/min/mL and plasm cholinesterase range of 2.2 to 6.9 μmol/min/mL. Despite the large interindividual variation presented, when one used the pre-exposure baseline it was possible to correlate symptoms of light poisoning of the exposure workers to carbamate with fall in the Er-ChE activity lesser then 30% of the pre-exposure baseline activity.

Development of a supercritical fluid extraction method for simultaneous determination of organophosphorus, organohalogen, organonitrogen and pyretroids pesticides in fruit and vegetables and its comparison with a conventional method by GC-ECD and GC-MS

The aim of this paper was to apply a multiresidue method using Supercritical Fluid Extraction (SFE) and capillary gas chromatography with electron capture and mass spectrometry detections in the analysis of the levels of pesticide residues in fruits and vegetables. Single laboratory validation of both solid-liquid and supercritical fluid extraction methods was carried out for 32 compounds selected from four pesticide classes (organochlorine, organonitrogen, organophosphorus and pyretroid) in blank and fortified samples of fresh lettuce, potato, apple and tomato. Recoveries for the majority of pesticides from fortified samples at fortification level of 0.04-0.10 mg kg -1 ranged 74-96% for both methods and confirmation of pesticide identity was performed by gas-chromatography-mass spectrometry in a selected-ion monitoring mode. Both methods showed good limits of detection (less 0.01 mg kg-1, depending on the pesticide and matrix) and the SFE method minimized environmental concerns, time, and laboratory work. ©2005 Sociedade Brasileira de Química.

Método multiresiduo para determinar pesticidas en frutas por extracción con fluido supercrítico

A rapid and reliable method for the determination of 25 compounds selected from four classes of pesticides in samples of fresh apples, grapes, pears, and strawberries purchased at a local supermarket, is presented. The study describes two different methods of extraction: solid-liquid extraction with acetone and supercritical fluid extraction. Clean-up was based on aminopropyl cartridge extraction followed by gas chromatography with an electron capture detector for simultaneous determinations. Confirmatory analysis was carried out by gas chromatography with mass spectrometry in the selected-ion monitoring (SIM) mode. Extraction efficiencies were directly compared and the methods were applied to the analysis of real samples. Recoveries for a majority of pesticides from standard samples at enrichment levels of 0.04-0.10 mg/ kg ranged from 77 to 96 % for both methods. The supercritical fluid extraction method showed good limits of detection (less than 0.01 mg/kg, depending on the pesticide and matrix) as well as minimizing environmental concerns, time, and laboratory effort. © 2006 Centro de Información Tecnológica.

Comparação de dois métodos de aplicação de fungicidas, irrigação por gotejamento e pulverização convencional no controle do mofo cinzento (Botrytis cinerea Pers.: Fr.) em vasos com plantas de lisianthus (Eustoma grandiflorum (Raf.) Shinn.)

Plan disease control techniques are used through the irrigation water, which reduces the labor and it improves application uniformity with smaller contact of the operator with toxic products, lower environmental impact and lower production cost. In order to control Botrytis cinerea the lisianthus culture, this work aimed to evaluate two fungicide application methods with different treatments. The fungicides were: thiophanate methyl (50 g i.a. L-1), thiophanate methyl + chlorothalonil (50 g i.a. L-1 + 35 g i.a. L-1) and iprodione (50 g i.a. L-1). Number of lesions, number of diseased floral buttons and height of the lisianthus plants were evaluated. It was possible to deduce, that in the growth stage (number of lesions in the plant) as well as in the final stage (number of floral buttons) of the lisianthus culture, the most efficient treatments were 2 (thiophanate methyl + chlorothalonil) and 3 (iprodione). Considering that treatment 2 is a mixture of two fungicides, a systemic and a contact one, independently of application methods, the mixture increased efficiency in relation to treatment 1 (thiophanate methyl). Thus, chemigation was as efficient as spreading technique.

Dissipation of DDT in a heavily contaminated soil in Mato Grosso, Brazil

After the prohibition of organochlorine-pesticide use in Brazil for controlling insect vector diseases, Mato Grosso State gathered the exceeding DDT and stored it irregularly in an open air area that belongs to the National Health Foundation, causing soil contamination. This study aimed to evaluate the contamination level and dissipation of p,p′-DDT and p,p′-DDE in this area. For that, surface soil samples were collected on 19 September 2000, 15 December 2000, 4 April 2001 and soil samples 30-40 cm; 60-70 cm and 90-100 cm deep were taken from five points in the studied area on 17 July 2001. The contaminants were determined by a small scale method which consists on extraction and clean-up steps combined into one step by transferring soil samples mixed with neutral alumina to a chromatographic column prepacked with neutral alumina and elution with hexane:dichloromethane (7:3 v:v). The eluate was concentrated and the analytes were quantified by gas chromatography with an electron-capture detector. p,p′-DDT at surface soil ranged from 3800 to 7300 mg kg -1. 30-40 cm deep soil sample concentrations varied from 0.036 to 440 mg kg -1 while 90-100 cm deep samples varied from 0.069 to 180 mg kg -1. Volatilization is probably the main dissipation process. The p,p′-DDT is moving slowly downward in the soil profile, however, the levels of this contaminant are high enough to present risk to underground waters. © 2005 Elsevier Ltd. All rights reserved.

Residues of organochlorine pesticides and PCBs in some Brazilian municipal solid waste compost

Persistent organic pollutants (POPs), organochlorine pesticides and polychlorinated biphenyls (PCBs), listed as per the Stockholm Convention (α -HCH, β -HCH, γ -HCH, p,p′-DDT, o,p′-DDT, p,p′-DDD, p,p′-DDE, aldrin, endrin, dieldrin, PCBs 28, 52, 118, 138, 153, and 180), were analyzed in municipal solid waste (MSW) compost samples from three different Brazilian composting plants located in three São Paulo State cities: Araras, Araraquara and São Paulo (Vila Leopoldinha). Quantitative and qualitative analyses were carried out using gas chromatography electron capture detection (GC-ECD) and gas chromatography mass spectrometry (GC-MS) (Ion Trap, electron impact ionization), respectively. The samples were analyzed in triplicate and the target POPs were not detected by GC-ECD. Twelve pollutants were identified in two samples when qualitative analysis (GC-MS) was used (β -HCH, γ -HCH, p,p′-DDT, o,p′-DDT, p,p′-DDD, and p,p′-DDE, PCBs 28, 118, 138, 153 and 180). The composting process has advantages such as urban solid waste reduction and landfill life-span increase, however the MSW compost quality, which can be utilized for agricultural purposes, should be evaluated and be controlled. This kind of study is the first step in making available information to answer questions regarding MSW compost for sustainable agricultural use, such as the pollutants accumulation in soil and in groundwater, and plants uptake. Copyright © Taylor & Francis Group, LLC.

Toxicidade aguda do sulfato de cobre e do extrato aquoso de folhas secas de nim para o caramujo (Pomacea canaliculata)

Snails can become an environmental and economic problem, causing substantial losses. The objective of this work was to estimate the acute toxicity of copper sulfate pentahydrate (CuSO4.5H2O) and the aqueous extract of dried neem leaves on snails (P. canaliculata) under laboratory conditions. In order to estimate the lethal concentration 50% (LC (I)50;96h), snails were exposed to six increasing copper sulfate concentrations (0.0; 0.01; 0.03; 0.05; 0.07 and 0.1 mg L-1) and six increasing concentrations of aqueous extract of dried neem leaves 0.0; 100; 125; 150; 175 and 200 mL aqueous extract of dried neem leaves L-1 water, equivalent to (0.0; 1.18; 1.47; 1.77; 2.06 and 2.36 mg azadirachtin L -1), in triplicate and one control treatment in an entirely random delineation. Estimated LC (I)50;96h, of copper sulfate was 0.02 mg copper sulfate L-1, with a 0.01 mg L-1 lower limit and a 0.03 mg L-1 upper limit. Estimated lethal concentration 50% of the aqueous extract of dried neem leaves was 142.75 mL L-1, equivalent to 1.68 mg L-1 of azadirachtine, with a 130.89 mL L-1 (1.54 mg L-1) low limit and 155.69 mL L-1 (1.83 mg L -1) as the upper limit.

Efeito da chuva sobre a ação do herbicida imazapyr no controle de plantas daninhas aquáticas

The aim of this study was to evaluate the influence of different periods of rainfall that occurred after the application of the imazapyr herbicide on the control efficiency of Pistia stratiotes and Eichhornia crassipes. We studied 10 mm rainfall, applied for 5' at different time periods (0h, 2h, 4h, 6h, 8h, 12h, 24h, not simulated rainfall) after the application of imazapyr formulation Arsenal NA, 250 g ai ha -1 (1.0 L cp ha -1). The experiment had completely randomized design with four replications. Plants were evaluated at 7, 14, 21, 28 and 35 days after application (DAA), and the results submitted to analysis of variance by F test and treatment means compared by Tukey's test (p <0. 05). The occurrence of rainfall up to 6 hours after herbicide application, plants of P. stratiotes, negatively affected its efficiency and control; rainfall intervals over 8 hours had no effect in control. The occurrence of rainfall at all time intervals did not affect the control of E. crassipes plants.

Fungigação no controle do mofo branco e produtividade do feijoeiro em condições de cerrado brasileiro

The aim of this research was to evaluate the white mold severity (Sclerotinia sclerotiorum (Lib.) of Bary), bean production components and yield (Phaseolus vulgaris L.), variety Perola, according to the application of procimidone fungicide (Sialex 500), through fungigation (center pivot) and automotive sprayer (Uniport). The study was carried under field production commercial conditions, in Primavera do Leste - MT - Brazil. The experiment consisted of 5 treatments (with 4 repetitions of 4 ha each), all with two procimidone applications (1.2 kg ha-1 each application, same as, 0.6 kg a.i. per hectare) to the 42 and 52 days after seeding. The water depths of 5.5 and 11.0 mm were tested in the application through central pivot (this had your checked uniformity), providing volumes of 55.000 and 110.000 L ha-1, respectively, and the volumes of 120 and 200 L ha-1 in the automotive sprayer. The severity of disease was evaluated by the percentage of the area affected by plant damage using diagramatic grade scale of white mold severity, as described by Azevedo (1998). The values were used to calculate the area under the disease progress curve (AUDPC). They were also analyzed, the number of the fungus apothecia during the crop cycle and the residual sclerotias weight in harvest. On this occasion, it was also evaluated the crop yield parameters: number of plants per plot (final stand), pods per plant, grains per pod, medium weight of 200 grains and productivity of grains. The AUDPC values, apothecia to 42, 49 and 56 days after seeding, sclerotias in 2 soil kg and the crop productivity parameters were submitted to the variance analysis and Tukey Test at 0.05 of probability. This test was also applied in the comparison among the different fungicide application methods, independent of spray volumes in each one. The statistical processing was accomplished by STAT program. The results showed that weren't differences among application techniques studied in relation to productivity parameters, however, best white mold control, smaller apothecia number to 49 and 56 days after seeding and smaller weight of residual sclerotias in the harvest were obtained with the fungigation, independently of the spray volume used.

Air-assistance and low volume application to control of asian rust on soybean crop

Currently, one of factors that cause the production cost increase of soybean crop is the pesticide application. The most important disease in soybean crop is Asian rust, caused by Phakopsora pachyrhizi Sydon & P. Sydon fungus, which can cause significant loss of the production. Therefore, this work aimed at evaluation of different spraying techniques on the spray deposits and some parameters of soybean crop: grain size, weight of 1 000 seeds and the crop productivity. Two experiments were carried out in the experimental area of FCA/UNESP (Faculdade de Ciencias Agronomicas/Universidade Estadual Paulista Julio de Mesquita Filho) - Botucatu, S P, Brazil, in soybean crop, Conquista variety, in the 2007/2008 season. In the first experiment, three air levels (0, 9 and 29 km/h of the air speed generated by fan) with flat fan nozzle XR 8002 with a spray volume of 130 l/ha were compared with a rotating nozzle - using low volume oily - LVO at 40 l/ha of spray volume. The second experiment was carried out under the same conditions as the previous experiment, including a control treatment (untreated plants). The disease severity was evaluated using a diagrammatic scale with a visual evaluation of the disease on 15 leaves of each plot. The grades varied between 0.6 and 78.5% of the disease severity. The use of air assistance when compared with the rotating system nozzle did not show significant differences for spray deposits on adaxial and abaxial surface of the leaves in bottom part of the plant. The air assistance with maximum air speed (29 km/h) increased the productivity with respect of the other treatments.