Treatment of estrogens and androgens in dairy wastewater by a constructed wetland system.

Constructed wetland systems (CWS) have been used as a low cost bio-filtration system to treat farm wastewater. While studies have shown that CWS are efficient in removing organic compounds and pathogens, there is limited data on the presence of hormones in this type of treatment system. The objective of this study was to evaluate the ability of the CWS to reduce estrogenic and androgenic hormone concentration in dairy wastewater. This was achieved through a year long study on dairy wastewater samples obtained froma surface flow CWS. Analysis of hormonal levels was performed using a solid phase extraction (SPE) sample clean-up method, combined with reporter gene assays (RGAs) which incorporate relevant receptors capable of measuring total estrogenic or androgenic concentrations as low as 0.24 ng L1 and 6.9 ng L1 respectively. Monthly analysis showed a mean removal efficiency for estrogens of 95.2%, corresponding to an average residual concentration of 3.2 ng L1 17b-estradiol equivalent (EEQ), below the proposed lowest observable effect concentration (LOEC) of 10 ng L1. However, for one month a peak EEQ concentration of 115 ng L1 was only reduced to 18.8 ng L1. The mean androgenic activity peaked at 360 ng L1 and a removal efficiency of 92.1% left an average residual concentration of 32.3 ng L1 testosterone equivalent (TEQ). The results obtained demonstrate that this type of CWS is an efficient system for the treatment of hormones in dairy wastewater. However, additional design improvements may be required to further enhance removal efficiency of peak hormone concentrations.

Platinum and Palladium in Semiconductor Photocatalytic Systems FACTORS AFFECTING THE PURIFICATION OF WATER AND AIR

A wide range of organic pollutants can be destroyed by semiconductor photocatalysis using titania. The purification of water and air contaminated with organic pollutants has been investigated by semiconductor photocatalysis for many years and in attempts to improve the purification rate platinum and palladium have been deposited, usually as fine particles, on the titania surface. Such deposits are expected to improve the rate of reduction of oxygen and so reduce the probability of electron-hole recombination and increase the overall rate of the reaction. The effectiveness of the deposits is reviewed here and appears very variable with reported rate enhancement factors ranging from 8 to 0.1. Semiconductor photocatalysis can be used to purify air (at temperatures > 100 degrees C) and Pt deposits can markedly improve the overall rate of mineralisation. However, volatile organic compounds containing an heteroatom can deactivate the photocatalyst completely and irreversibly. Factors contributing to the success of the processes are considered. The use of chloro-Pt(IV)-titania and other chloro-platinum group metals-titania complexes as possible visible light sensitisers for water and air purification is briefly reviewed.

Applied aspects of Rhodococcus genetics

Eubacteria of the genus Rhodococcus are a diverse group of microorganisms commonly found in many environmental niches from soils to seawaters and as plant and animal pathogens. They exhibit a remarkable ability to degrade many organic compounds and their economic importance is becoming increasingly apparent. Although their genetic organisation is still far from understood, there have been many advances in recent years. Reviewed here is the current knowledge of rhodococci relating to gene transfer, recombination, plasmid replication and functions, cloning vectors and reporter genes, gene expression and its control, bacteriophages, insertion sequences and genomic rearrangements. Further fundamental studies of Rhodococcus genetics and the application of genetic techniques to the these bacteria will be needed for their continued biotechnological exploitation.

Survival and persistence of opportunistic Burkholderia species in host cells

Burkholderia are microorganisms that have a unique ability to adapt and survive in many different environments. They can also serve as biopesticides and be used for the biodegradation of organic compounds. Usually harmless while living in the soil, these bacteria are opportunistic pathogens of plants and immunocompromised patients, and occasionally infect healthy individuals. Some of the species in this genus can also be utilised as biological weapons. They all possess very large genomes and have two or more circular chromosomes. Their survival and persistence, not only in the environment but also in host cells, offers a remarkable example of bacterial adaptation.

The biology of habitat dominance; can microbes behave as weeds?

Competition between microbial species is a product of, yet can lead to a reduction in, the microbial diversity of specific habitats. Microbial habitats can resemble ecological battlefields where microbial cells struggle to dominate and/or annihilate each other and we explore the hypothesis that (like plant weeds) some microbes are genetically hard-wired to behave in a vigorous and ecologically aggressive manner. These 'microbial weeds' are able to dominate the communities that develop in fertile but uncolonized - or at least partially vacant - habitats via traits enabling them to out-grow competitors; robust tolerances to habitat-relevant stress parameters and highly efficient energy-generation systems; avoidance of or resistance to viral infection, predation and grazers; potent antimicrobial systems; and exceptional abilities to sequester and store resources. In addition, those associated with nutritionally complex habitats are extraordinarily versatile in their utilization of diverse substrates. Weed species typically deploy multiple types of antimicrobial including toxins; volatile organic compounds that act as either hydrophobic or highly chaotropic stressors; biosurfactants; organic acids; and moderately chaotropic solutes that are produced in bulk quantities (e.g. acetone, ethanol). Whereas ability to dominate communities is habitat-specific we suggest that some microbial species are archetypal weeds including generalists such as: Pichia anomala, Acinetobacter spp. and Pseudomonas putida; specialists such as Dunaliella salina, Saccharomyces cerevisiae, Lactobacillus spp. and other lactic acid bacteria; freshwater autotrophs Gonyostomum semen and Microcystis aeruginosa; obligate anaerobes such as Clostridium acetobutylicum; facultative pathogens such as Rhodotorula mucilaginosa, Pantoea ananatis and Pseudomonas aeruginosa; and other extremotolerant and extremophilic microbes such as Aspergillus spp., Salinibacter ruber and Haloquadratum walsbyi. Some microbes, such as Escherichia coli, Mycobacterium smegmatis and Pseudoxylaria spp., exhibit characteristics of both weed and non-weed species. We propose that the concept of nonweeds represents a 'dustbin' group that includes species such as Synodropsis spp., Polypaecilum pisce, Metschnikowia orientalis, Salmonella spp., and Caulobacter crescentus. We show that microbial weeds are conceptually distinct from plant weeds, microbial copiotrophs, r-strategists, and other ecophysiological groups of microorganism. Microbial weed species are unlikely to emerge from stationary-phase or other types of closed communities; it is open habitats that select for weed phenotypes. Specific characteristics that are common to diverse types of open habitat are identified, and implications of weed biology and open-habitat ecology are discussed in the context of further studies needed in the fields of environmental and applied microbiology.

Stability and performance enhancements of Electrokinetic-Fenton soil remediation

Electrokinetic process is a potential in situ soil remediation process which transports the contaminants via electromigration and electroosmosis. For organic compounds contaminated soil, Fenton’s reagent is utilized as a flushing agent in electrokinetic process (Electrokinetic-Fenton) so that removal of organic contaminants could be achieved by in situ oxidation/destruction. However, this process is not applied widely in industries as the stability issue for Fenton’s reagent is the main drawback. The aim of this mini review is to summarize the developments of Electrokinetic-Fenton process on enhancing the stability of Fenton’s reagent and process efficiency in past decades. Generally, the enhancements are conducted via four paths: (1) chemical stabilization to delay H2O2 decomposition, (2) increase of oxidant availability by monitoring injection method for Fenton’s reagent, (3) electrodes operation and iron catalysts and (4) operating conditions such as voltage gradient, electrolytes and H2O2 concentration. In addition, the types of soils and contaminants are also showing significant effect as the soil with low acid buffering capacity, adequate iron concentration, low organic matter content and low aromatic ring organic contaminants generally gives better efficiency.

Use of water in aiding olefin/paraffin (liquid + liquid) extraction via complexation with a silver bis(trifluoromethylsulfonyl)imide salt

This paper describes the extraction of C₅–C₈ linear α-olefins from olefin/paraffin mixtures of the same carbon number via a reversible complexation with a silver salt (silver bis(trifluoromethylsulfonyl)imide, Ag[Tf₂N]) to form room temperature ionic liquids [Ag(olefin)_x][Tf₂N]. From the experimental (liquid + liquid) equilibrium data for the olefin/paraffin mixtures and Ag[Tf₂N], 1-pentene showed the best separation performance while C₇ and C₈ olefins could only be separated from the corresponding mixtures on addition of water which also improves the selectivity at lower carbon numbers like the C₅ and C₆, for example. Using infrared and Raman spectroscopy of the complex and Ag[Tf₂N] saturated by olefin, the mechanism of the extraction was found to be based on both chemical complexation and the physical solubility of the olefin in the ionic liquid ([Ag(olefin)_x][Tf₂N]). These experiments further support the use of such extraction techniques for the separation of olefins from paraffins.

Remediation of oily wastewater from an interceptor tank using a novel photocatalytic drum reactor

A novel photocatalytic reactor has been developed to remediate oily wastewaters. In the first instance degradation rates of model organic compounds, methylene blue (MB) and 4-c hlorophenol (4-CP) were determined. The experimental set-up investigated a 1:10 w/v catalyst to organic solution volume, 30 g catalyst, 300 mls MB (10 μM) or 4-CP (100 μM). The catalyst investigated was a pellet catalyst to improve separation of the remediated volume from the catalyst following treatment. MB concentration decreased by 93% after 15 mins irradiation whilst 4-CP concentration decreased by 94% following 90 mins irradiation. Oily waste water (OWW) from an interceptor tank typically containing diesel oils was obtained from Sureclean, an environmental clean-up company. The OWW was treated using the same conditions as MB and 4-CP, the model organic compounds. Levels of total organic carbon (TOC) and total petroleum hydrocarbon (TPH) were used to monitor the efficacy of the photocatalytic reactor. TOC reduced by 45% following two 90 mins treatment cycles. TPH reduced by 45% following 90 mins irradiation and by a further 25% during a second stage of treatment. This reactor can be used as a polishing technique assembled within a wastewater treatment plant. Allowing for more than one pass through the reactor improves its efficiency. 

Mineralisation of 2,4-dichlorophenol and glucose placed into the same or different hydrological domains as a bacterial inoculant

The spatial location of microorganisms in the soil three-dimensional structure with respect to their substrates plays an important role in the persistence and turnover of natural and xenobiotic organic compounds. To study the effect of spatial location on the mineralisation of ¹⁴C-2,4-dichlorophenol (2,4-DCP, 0.15 or 0.31 μmol g^-1) and ¹⁴C-glucose (2.77 μmol g^-1), columns packed with autoclaved soil aggregates (2-5 mm) were used. Using a chloride tracer of water movement, the existence of 'immobile' water, which was by-passed by preferentially flowing 'mobile' water, was demonstrated. By manipulation of the soil moisture content, the substrates were putatively placed to these conceptual hydrological domains (immobile and mobile water). Leaching studies revealed that approximately 1.7 (glucose) and 3.4 (2.4-DCP) times the amount of substrate placed in mobile water was recovered in the first 4 fractions of leachate when compared to substrate placed in immobile water. The marked difference in the breakthrough curves was taken as evidence of successful substrate placement. The 2,4-DCP degrading bacterium, Burkholderia sp. RASCc2, was inoculated in mobile water (1.8-5.2 × 10⁷ cells g^-1 soil) and parameters (asymptote, time at maximum rate, calculated maximum rate) describing the mineralisation kinetics of 2,4-DCP and glucose previously added to immobile or mobile water domains were compared, For glucose, there was no significant effect (P > 0.1) of substrate placement on any of the mineralisation parameters. However, substrate placement had a significant effect (P < 0.05) on parameters describing 2,4-DCP mineralisation. In particular, 2,4-DCP added in mobile water was mineralised with a greater maximum rate and with a reduced time at maximum rate when compared to 2,4-DCP added to immobile water. The difference in response between the two test substrates may reflect the importance of sorption in controlling the spatial bioavailability of compounds in soil. © 2002 Elsevier Science Ltd. All rights reserved.

Desenvolvimento de sensores de fibra óptica para monitorização de compostos orgânicos voláteis em ambientes industriais

O objectivo geral deste trabalho consistiu no desenvolvimento de novos sensores químicos de fibra óptica (OF) para análise de compostos orgânicos voláteis (VOCs) em ambientes industriais. A componente de detecção dos sensores desenvolvidos é constituída por uma pequena secção de fibra óptica revestida com um filme de polímero. A morfologia dos filmes poliméricos foi analisada e caracterizada por microscopia electrónica de varrimento (SEM), sendo a espessura dos filmes determinada por espectroscopia de retrodispersão de Rutherford (RBS, acrónimo do inglês Rutherford backscattering spectrometry). O desempenho analítico dos sensores de OF foi avaliado relativamente a diferentes parâmetros operacionais, tais como, concentração da solução de revestimento, técnica de deposição do filme polimérico, temperatura da célula de injecção, temperatura de cura do material polimérico, caudal do gás de arraste, comprimento de onda e frequência de funcionamento do laser, configurações estruturais da célula de injecção e do tubo analítico. Foram desenvolvidos dois sensores de OF a operar na região do infravermelho para determinação de diferentes classes de VOCs, nomeadamente hidrocarbonetos aromáticos, clorados e alifáticos, além de álcoois. Os sensores de OF desenvolvidos apresentaram adequadas características analíticas em termos de sensibilidade, linearidade, repetitibilidade e reprodutibilidade do sinal analítico, sendo o tempo de resposta de aproximadamente 30 segundos. Foi também desenvolvido um sensor de OF para especiação de benzeno, tolueno e o-xileno a operar na região do visível (635 - 650 nm), tendo sido aplicado à análise de amostras reais de ar de uma indústria de solventes. Relativamente à monitorização de VOCs em ambientes industriais, foi desenvolvido um sensor de OF para monitorização in situ e de forma remota (até uma distância máxima de 60 metros do local de amostragem) de benzeno, tolueno, etilbenzeno, p-xileno, m-xileno e o-xileno (BTEX), utilizando um díodo laser a 1550 nm. O desempenho analítico do sensor desenvolvido foi comparado, para a determinação de BTEX, com a cromatografia gasosa acoplada à detecção com ionização de chama (GC-FID). Foram ainda desenvolvidos dois detectores de fibra óptica acoplados a um cromatógrafo de gás para especiação de álcoois e hidrocarbonetos aromáticos. A metodologia desenvolvida baseada em cromatografia gasosa acoplada a um detector de fibra óptica (GC-OF) foi aplicada à análise de amostras reais de ar de uma indústria de solventes, comparando os respectivos resultados com os obtidos por GC-FID. Por fim foi efectuado um estudo visando a obtenção de um modelo geral para a resposta analítica dos sensores de fibra óptica desenvolvidos.

Síntese e aplicações catalíticas na funcionalização de alcanos de novos compostos com polioxometalatos e catiões orgânicos

A presente dissertação, que no seu conjunto se propõe apresentar o estudo de oxidação de compostos orgânicos com peróxido de hidrogénio na presença dos aniões do tipo Keggin, mono-substituídos por MnIII e FeIII, sob a forma de sais de tetra-n-butilamónio (TBA) e suportados em matriz de sílica funcionalizada, enquanto vital método de obtenção de importante precursores de síntese orgânica, tem na sua base o trabalho de Doutoramento desenvolvido no Departamento de Química da Universidade de Aveiro. Os compostos preparados e testados em sistema homogéneo foram os sais de TBA dos aniões de Keggin, de fórmula geral [XW11M(H2O)O39]n-, onde X = P, Si ou B e M = MnIII e FeIII. Em sistema heterogéneo foram testados diferentes materiais, que diferem entre si na matriz de sílica. Assim, fez-se a heterogeneização de [PW11Fe(H2O)O39]4- em sílica funcionalizada com catiões de césio e grupos propilamónio; [BW11Fe(H2O)O39]6- e [SiW11Fe(H2O)O39]5- foram imobilizados em sílica contendo grupos aminopropilo e o anião [PW11Mn(H2O)O39]4- foi suportado em sílica quimicamente modificada com grupos alquilamónio. Os substratos orgânicos estudados incluem o 1H-indeno, 1,2-di-hidronaftaleno, etilbenzeno, cumeno, p-cimeno, sec-butilbenzeno, 1- e 2-etilnaftaleno, cis-cicloocteno e ciclooctano. Paralelamente usaram-se alguns outros substratos, quando necessário obter esclarecimentos mecanísticos. A tese assenta numa estrutura composta por 7 capítulos. Na primeira, faz-se uma abordagem aos polioxometalatos e às reacções de oxidação de hidrocarbonetos, com particular destaque no uso de polioxometalatos em catálise oxidativa e também no uso de peróxido de hidrogénio como oxidante. A eficiência catalítica dos aniões de Keggin mono substituídos por MnIII e FeIII, em sistema homogéneo foi avaliada na oxidação de compostos orgânicos característicos, nomeadamente de ciclo-alcenilbenzenos, alquilbenzenos, ciclo-alquilbenzenos e hidrocarbonetos aromáticos policíclicos com H2O2, em acetonitrilo. Os resultados destes estudos encontram-se descritos nos capítulos dois, três e quatro desta tese. Estes compostos mostraram-se catalisadores eficientes e selectivos para a oxidação de alcanos e alcenos. O quinto capítulo da tese prossegue com a síntese, caracterização e eficiência catalítica dos polioxotungstatos referidos anteriormente imobilizados numa matriz de sílica funcionalizada com iões césio (SiO2-Cs), grupos aminopropilo (SiO2–(CH2)3NH2) ou trietilpropilamónio (SiO2-(CH2)3N(Et)3). A actividade catalítica destes compostos foi estudada utilizando o cis-cicloocteno e ciclooctano como substratos padrão. A oxidação de cis-clicoocteno originou o epóxido com 100% de selectividade e o catalisador foi reutilizado durante 4 ciclos com elevada eficiência. No sexto capítulo, são descritas as metodologias experimentais de síntese dos novos compostos, as condições catalíticas, a instrumentação e demais métodos e procedimentos usados. No sétimo e último capítulo, tecem-se as conclusões finais e apresentam-se algumas perspectivas de trabalho futuro utilizando o sistema, POM/H2O2, usado neste trabalho.

Contribution of biomass combustion to air pollutant emissions

In Portugal, it was estimated that around 1.95 Mton/year of wood is used in residential wood burning for heating and cooking. Additionally, in the last decades, burnt forest area has also been increasing. These combustions result in high levels of toxic air pollutants and a large perturbation of atmospheric chemistry, interfere with climate and have adverse effects on health. Accurate quantification of the amounts of trace gases and particulate matter emitted from residential wood burning, agriculture and garden waste burning and forest fires on a regional and global basis is essential for various purposes, including: the investigation of several atmospheric processes, the reporting of greenhouse gas emissions, and quantification of the air pollution sources that affect human health at regional scales. In Southern Europe, data on detailed emission factors from biomass burning are rather inexistent. Emission inventories and source apportionment, photochemical and climate change models use default values obtained for US and Northern Europe biofuels. Thus, it is desirable to use more specific locally available data. The objective of this study is to characterise and quantify the contribution of biomass combustion sources to atmospheric trace gases and aerosol concentrations more representative of the national reality. Laboratory (residential wood combustion) and field (agriculture/garden waste burning and experimental wildland fires) sampling experiments were carried out. In the laboratory, after the selection of the most representative wood species and combustion equipment in Portugal, a sampling program to determine gaseous and particulate matter emission rates was set up, including organic and inorganic aerosol composition. In the field, the smoke plumes from agriculture/garden waste and experimental wildland fires were sampled. The results of this study show that the combustion equipment and biofuel type used have an important role in the emission levels and composition. Significant differences between the use of traditional combustion equipment versus modern equipments were also observed. These differences are due to higher combustion efficiency of modern equipment, reflecting the smallest amount of particulate matter, organic carbon and carbon monoxide released. With regard to experimental wildland fires in shrub dominated areas, it was observed that the largest organic fraction in the samples studied was mainly composed by vegetation pyrolysis products. The major organic components in the smoke samples were pyrolysates of vegetation cuticles, mainly comprising steradienes and sterol derivatives, carbohydrates from the breakdown of cellulose, aliphatic lipids from vegetation waxes and methoxyphenols from the lignin thermal degradation. Despite being a banned practice in our country, agriculture/garden waste burning is actually quite common. To assess the particulate matter composition, the smoke from three different agriculture/garden residues have been sampled into 3 different size fractions (PM2.5, PM2.5-10 and PM>10). Despite distribution patterns of organic compounds in particulate matter varied among residues, the amounts of phenolics (polyphenol and guaiacyl derivatives) and organic acids were always predominant over other organic compounds in the organosoluble fraction of smoke. Among biomarkers, levoglucosan, β-sitosterol and phytol were detected in appreciable amounts in the smoke of all agriculture/garden residues. In addition, inositol may be considered as an eventual tracer for the smoke from potato haulm burning. It was shown that the prevailing ambient conditions (such as high humidity in the atmosphere) likely contributed to atmospheric processes (e.g. coagulation and hygroscopic growth), which influenced the particle size characteristics of the smoke tracers, shifting their distribution to larger diameters. An assessment of household biomass consumption was also made through a national scale survey. The information obtained with the survey combined with the databases on emission factors from the laboratory and field tests allowed us to estimate the pollutant amounts emitted in each Portuguese district. In addition to a likely contribution to the improvement of emission inventories, emission factors obtained for tracer compounds in this study can be applied in receptor models to assess the contribution of biomass burning to the levels of atmospheric aerosols and their constituents obtained in monitoring campaigns in Mediterranean Europe.

Indoor air quality in elementary schools of Lisbon and Aveiro

Tem havido uma preocupação crescente com a qualidade do ar interior (QAI) nas escolas em muitos países. Muitos estudos epidemiológicos têm encontrado diferenças regionais entre ambientes interiores. Apesar da elevada incidência de asma e rinite na população infantil, praticamente nada se sabia sobre a QAI em escolas portuguesas. A percepção dos problemas de QAI é crucial para avaliar os riscos para a saúde e rendimento dos estudantes, e para sugerir meios de reduzir a exposição a poluentes indesejáveis. Neste estudo procurou-se obter as concentrações de poluentes de interesse em estabelecimentos de ensino do 1º ciclo de Lisboa e Aveiro, estimar o estado atual de casos de asma e rinite em escolas primárias da capital, avaliar a influência de diferentes materiais das salas de aula/construção e hábitos escolares na QAI, identificar potenciais fontes de poluentes nos interiores e exteriores das salas de aula e propor medidas mitigadoras. Catorze escolas de Lisboa foram visitadas para obter a caracterização física das construções em termos de estrutura, ventilação, materiais de acabamento, produtos de limpeza, densidade de ocupação e potenciais fontes interiores de poluição. Os estudantes foram questionados sobre os seus hábitos e sintomas respiratórios através de inquéritos do modelo ISAAC (International Study of Asthma and Allergies in Childhood). Durante a primavera, outono e inverno (2008-2010), nas salas de aula e pátios, foram monitorizados, por amostragem passiva, compostos orgânicos voláteis (COVs), carbonilos e dióxido de azoto (NO2). Foram também medidos parâmetros de conforto e níveis de microrganismos. Duas escolas localizadas, uma no centro da cidade e outra na região suburbana, em Aveiro foram estudadas em 2010. Parâmetros de conforto, microrganismos, COVs, NO2, material particulado (PM10) foram medidos no interior e no exterior de ambas escolas. Os iões solúveis, carbono orgânico e elementar (OC e EC), e compostos orgânicos presentes no material particulado foram subsequentemente analisados em laboratório. Uma medida mitigadora - fitoremediação - foi avaliada na escola do centro da cidade de Aveiro em 2011. Os resultados do estudo mostraram que a QAI é pior do que a do ar exterior. Em geral, os níveis de CO2 e dos bioaerosóis excederam os níveis máximos aceitáveis para o conforto dos ocupantes estipulado pelas regulamentações portuguesas. Quase todos os COVs e carbonilos identificados mostraram razões interior/exterior (I/E) maiores que uma unidade, o que demonstra a importante contribuição de fontes interiores em todas as escolas. As razões I/E das concentrações de NO2 nunca excederam a unidade. Os níveis interiores diários de PM10 foram sempre maiores que os exteriores, exceto nos fins de semana. Após a colocação de plantas numa das salas de aula, observou-se uma redução estatisticamente significativa nos níveis de CO2, COVs, carbonilos, PM10, OC, e dos iões nitrato, sulfato, amónia, cálcio e carbonato. A possível redução dos níveis de poluentes no interior após a colocação de plantas pode representar uma solução de baixo custo para reduzir a exposição a muitos compostos, melhorar o rendimento e aumentar o bem estar dos alunos e professores em sala de aula.

Phylogenetic and functional diversity of estuarine bacterioneuston

A micro-camada superficial da água (SML) é caracterizada pela ocorrência de grandes quantidades de compostos orgânicos, pela acumulação de contaminantes antropogênicos e é submetida a uma intensa radiação solar, extrema mudança de temperatura e, no caso dos estuários, flutuação de salinidade. Estas propriedades físico-químicas estão, provavelmente, a modular a comunidade bacteriana (bacterioneuston) com propriedades filogenéticas e funcionais específicas. Neste estudo, as abordagens dependentes e independentes do cultivo foram aplicadas para avaliar a estrutura e dinâmica das comunidades bacterioneuston e bacterioplâncton em três localizações geográficas ao longo do estuário da Ria de Aveiro. Além disso, comparámos a diversidade filogenética de grupos específicos (Aeromonas, Pseudomonas e Psychrobacter) presentes em bacterioneuston e bacterioplâncton. Finalmente, as duas comunidades foram comparadas em termos de prevalência e diversidade de bactérias resistentes aos antibióticos e respetivos genes de resistência. Bactérias heterotróficas cultiváveis foram enriquecidas em SML. Eletroforese em gel de gradiente desnaturante (DGGE) permitiu a identificação de filotipos específicos em SML. Além disso, a análise de agrupamento dos perfis de DGGE de ambas as comunidades revelou uma ligeira tendência de agrupamento de acordo com a camada amostrada. As diferenças entre as duas comunidades variaram de acordo com factores espaciais e temporais. Em termos de diversidade filogenética de grupos específicos, não foram identificadas diferenças consistentes entre SML e UW com relação às comunidades de Aeromonas. Com relação ao género Pseudomonas, uma unidade operacional taxonómica cultivável foi consistentemente hiper-representada nas amostras de SML. Metodologias dependentes e independentes do cultivo revelaram a presença de populações de Psychrobacter complexas e muito estáveis em todos os sítios e datas de amostragens, com diferenças significativas entre as comunidades de Psychrobacter presentes em SML e UW. Estirpes representativas de prováveis novas espécies também foram cultivadas. Em termos de resistência aos antibióticos, a prevalência de bactérias resistentes em SML foi alta sugerindo selecção pelas condições presentes em SML. É preciso enfatizar que a resistência aos antibióticos foi incomum entre as bactérias estuarinas e os mecanismos de resistência foram, predominantemente, intrínsecos. Pela combinação de abordagens inovadoras dependentes e independentes do cultivo, este estudo forneceu novas e consistentes informações com relação às diferenças em ambas as comunidades bacterianas e em relação a alguns dos fatores que contribuem para a sua formação.

Toxicogenomics of natural and anthropogenic effectors in eleutheroembryos

The introduction of chemicals into the environment by human activities may represent a serious risk to environmental and human health. Environmental risk assessment requires the use of efficient and sensitive tools to determine the impact of contaminants on the ecosystems. The use of zebrafish for the toxicity assessment of pharmaceuticals, drugs, and pollutants, is becoming well accepted due to zebrafish unique advantages for the screening of compounds for hazard identification. The aim of the present work is to apply toxicogenomic approaches to identify novel biomarkers and uncovered potential modes of action of classic and emergent contaminants able to disrupt endocrine systems, such as the Retinoic Acid Receptor, Retinoid X Receptor and the Aryl Hydrocarbon Receptor. This study relies on different nuclear and cytosolic protein receptors and other conditional (ligand- or stress- activated) transcriptional factors that are intimately involved in the regulation of defensome genes and in mechanisms of chemical toxicity. The transcriptomic effects of organic compounds, endogenous compounds, and nanoparticles were analysed during the early stages of zebrafish development. Studying the gene expression profiles of exposed and unexposed organisms to pollutants using microarrays allowed the identification of specific gene markers and to establish a "genetic code" for the tested compounds. Changes in gene expression were observed at toxicant concentrations that did not cause morphological effects. Even at low toxicant concentrations, the observed changes in transcript levels were robust for some target genes. Microarray responses of selected genes were further complemented by the real time quantitative polymerase chain reaction (qRT-PCR) methodology. The combination of bio-informatic, toxicological analyses of differential gene expression profiles, and biochemical and phenotypic responses across the treatments allowed the identification of uncovered potential mechanisms of action. In addition, this work provides an integrated set of tools that can be used to aid management-decision making by improving the predictive capability to measure environmental stress of contaminants in freshwater ecosystems. This study also illustrates the potential of zebrafish embryos for the systematic, large-scale analysis of chemical effects on developing vertebrates.