Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Software Licensing: Implementing Electronic Licensing in Medical Technology Company

The purpose of this thesis is to examine software licensing, how a software developer can benefit from it and to define specifications for licensing system of software based medical technology product. The thesis has been divided into theoretical and empirical parts. In the theoretical part the concept of software licensing and different aspects that are connected to it are examined with a help of research material. On the ground of this research, in the empirical part, a licensing system for a medical software product called iCentral is designed. The empirical part is based on interviews, questionnaire and on authors own experience gained while working for the case-company.The thesis has great practical importance for the case-company by proposing both an ideal, and more importantly, practical implementation for a licensing system of a product. Thesis shows that electronic licensing is a viable option to sell medical technology products without a need to revise existing procedures or the enterprise resource system in the case company.

Analysis of the structural and electronic properties of 1-(5-Hydroxymethyl - 4 -[ 5 - (5-oxo-5-piperidin-1-yl-penta-1,3dienyl)-benzo[1,3]dioxol-2-yl] -tetrahydro-furan-2-yl)-5-methyl-1H-pyrimidine-2,4dione molecule

The structural and electronic properties of 1-(5-Hydroxymethyl - 4 -[ 5 - (5-oxo-5-piperidin- 1 -yl-penta- 1,3 -dienyl)-benzo [1,3] dioxol- 2 -yl]-tetrahydro -furan-2 -yl)-5-methy l-1Hpyrimidine-2,4dione (AHE) molecule have been investigated theoretically by performing density functional theory (DFT), and semi empirical molecular orbital calculations. The geometry of the molecule is optimized at the level of Austin Model 1 (AM1), and the electronic properties and relative energies of the molecules have been calculated by density functional theory in the ground state. The resultant dipole moment of the AHE molecule is about 2.6 and 2.3 Debyes by AM1 and DFT methods respectively, This property of AHE makes it an active molecule with its environment, that is AHE molecule may interacts with its environment strongly in solution.

Estimation of standard enthalpy of formation of alkanes in gaseous state by calculating size, structural and electronic parameters in the molecules

A quantitative analysis is made on the correlation ship of thermodynamic property, i.e., standard enthalpy of formation (ΔH fº) with Kier's molecular connectivity index(¹Xv),vander waal's volume (Vw) electrotopological state index (E) and refractotopological state index (R) in gaseous state of alkanes. The regression analysis reveals a significant linear correlation of standard enthalpy of formation (ΔH fº) with ¹Xv, Vw, E and R. The equations obtained by regression analysis may be used to estimate standard enthalpy of formation (ΔH fº) of alkanes in gaseous state.

Licensing of eResources - views from Denmark's Electronic Research Library (DEFF)

Bo Öhrströmin esitys Kirjastoverkkopäivillä 27.10.2011 Helsingissä.

Development of an automated bench top electronic penetrometer

The aim of this study was to develop a an automated bench top electronic penetrometer (ABEP) that allows performing tests with high rate of data acquisition (up to 19,600 Hz) and with variation of the displacement velocity and of the base area of cone penetration. The mechanical components of the ABEP are: a supporting structure, stepper motor, velocity reducer, double nut ball screw and six penetration probes. The electronic components of ABEP are: a "driver" to control rotation and displacement, power supply, three load cells, two software programs for running and storing data, and a data acquisition module. This penetrometer presented in compact size, portable and in 32 validation tests it proved easy to operate, and showed high resolution, high velocity in reliability in data collection. During the validation tests the equipment met the objectives, because the test results showed that the ABEP could use different sizes of cones, allowed work at different velocities, showed for velocity and displacement, were only 1.3% and 0.7%, respectively, at the highest velocity (30 mm s-1) and 1% and 0.9%, respectively for the lowest velocity (0.1 mm s-1).

Usable Privacy Preservation in Mobile Electronic Personality

Personalised ubiquitous services have rapidly proliferated due technological advancements in sensing, ubiquitous and mobile computing. Evolving societal trends, business and the economic potential of Personal Information (PI) have overlapped the service niches. At the same time, the societal thirst for more personalised services has increased and are met by soliciting deeper and more privacy invasive PI from customers. Consequentially, reinforcing traditional privacy challenges and unearthed new risks that render classical safeguards ine ective. The absence of solutions to criticise personalised ubiquitous services from privacy perspectives, aggravates the situation. This thesis presents a solution permitting users' PI, stored in their mobile terminals to be disclosed to services in privacy preserving manner for personalisation needs. The approach termed, Mobile Electronic Personality Version 2 (ME2.0), is compared to alternative mechanisms. Within ME2.0, PI handling vulnerabilities of ubiquitous services are identi ed and sensitised on their practices and privacy implications. Vulnerability where PI may leak through covert solicits, excessive acquisitions and legitimate data re-purposing to erode users privacy are also considered. In this thesis, the design, components, internal structures, architectures, scenarios and evaluations of ME2.0 are detailed. The design addresses implications and challenges leveraged by mobile terminals. ME2.0 components and internal structures discusses the functions related to how PI pieces are stored and handled by terminals and services. The architecture focusses on di erent components and their exchanges with services. Scenarios where ME2.0 is used are presented from di erent environment views, before evaluating for performance, privacy and usability.

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

From electronic spare part catalog to eBusiness: Finding the best practices

Companies and organizations business activities rely on information. IT systems that manage master data must provide the highest level of service, world-class scalability and reliable information. This study discusses product information and how it can support the creation of a spare part catalog and the launching of eBusiness. The study consists of a theoretical and empirical part. The theoretical part contains a literature review and a framework for the analysis. For the empirical study two companies were selected and their information management processes were studied and analyzed based on the framework. The empirical results indicate that the challenges the companies face reflect the ones that can be found in the literature study. The results of the empirical study also show that the companies had recognized the issues which need to be developed and had recognized trends in eBusiness and product information management.

Regioselective modification of galactose-containing polysaccharides in aqueous media

Biorefining is defined as sustainable conversion of biomass into marketable products and energy. Forests cover almost one third of earth’s land area, and account for approximately 40% of the total annual biomass production. In forest biorefining, the wood components are, in addition to the traditional paper and board products, converted into chemicals and biofuels. The major components in wood are cellulose, hemicelluloses, and lignin. The main hemicellulose in softwoods, which are of interest especially for the Nordic forest industry, is O-acetyl galactoglucomannan (GGM). GGM can be isolated in industrial scale from the waste waters of the mechanical pulping process, but is not yet today industrially utilized. In order to attain desired properties of GGM for specific end-uses, chemical and enzymatic modifications can be performed. Regioselective modifications of GGM, and other galactose-containing polysaccharides were done by oxidations, and by combining oxidations with subsequent derivatizations of the formed carbonyl or carboxyl groups. Two different pathways were investigated: activation of the C-6 positions in different sugar units by TEMPO-mediated oxidation, and activation of C-6 position in only galactose-units by oxidation catalyzed by the enzyme galactose oxidase. The activated sites were further selectively derivatized; TEMPO-oxidized GGM by a carbodiimide-mediated reaction forming amides, and GO-oxidized GGM by indium-mediated allylation introducing double or triple bonds to the molecule. In order to better understand the reaction, and to develop a MALDI-TOF-MS method for characterization of regioselectively allylated GGM, α-D-galactopyranoside and raffinose were used as model compounds. All reactions were done in aqueous media. To investigate the applicability of the modified polysaccharides for, e.g., cellulose surface functionalization, their sorption onto pulp fibres was studied. Carboxylation affects the sorption tendency significantly; a higher degree of oxidation leads to lower sorption. By controlling the degree of oxidation of the polysaccharides and the ionic strength of the sorption media, high degrees of sorption of carboxylated polysaccharides onto cellulose could, however, be obtained. Anionic polysaccharides were used as templates during laccase-catalyzed polymerization of aniline, offering a green, chemo-enzymatic route for synthesis of conducting polyaniline (PANI) composite materials. Different polysaccharide templates, such as, native GGM, TEMPO-oxidized GGM, naturally anionic κ-carrageenan, and nanofibrillated cellulose produced by TEMPO-oxidation, were assessed. The conductivity of the synthesized polysaccharide/PANI biocomposites varies depending on the polysaccharide template; κ-CGN, the anionic polysaccharide with the lowest pKa value, produces the polysaccharide/PANI biocomposites with the highest conductivity. The presented derivatization, sorption, and polymerization procedures open new application windows for polysaccharides, such as spruce GGM. The modified polysaccharides and the conducting biocomposites produced provide potential applications in biosensors, electronic devices, and tissue engineering.

A high frequency electronic transducer for multiphase flow measurements

This paper describes an electronic transducer for multiphase flow measurement. Its high sensitivity, good signal to noise ratio and accuracy are achieved through an electrical impedance sensor with a special guard technique. The transducer consists of a wide bandwidth and high slew rate differentiator where the lead inductance and stray capacitance effects are compensated. The sensor edge effect is eliminated by using a guard electrode based on the virtual ground potential of the operational amplifier. A theoretical modeling and a calibration method are also presented. The results obtained seem to confirm the validity of the proposed technique.

Integration of Electronic Commerce and Enterprise Systems

The necessity of EC (Electronic Commerce) and enterprise systems integration is perceived from the integrated nature of enterprise systems. The proven benefits of EC to provide competitive advantages to the organizations force enterprises to adopt and integrate EC with their enterprise systems. Integration is a complex task to facilitate seamless flow of information and data between different systems within and across enterprises. Different systems have different platforms, thus to integrate systems with different platforms and infrastructures, integration technologies, such as middleware, SOA (Service-Oriented Architecture), ESB (Enterprise Service Bus), JCA (J2EE Connector Architecture), and B2B (Business-to-Business) integration standards are required. Huge software vendors, such as Oracle, IBM, Microsoft, and SAP suggest various solutions to address EC and enterprise systems integration problems. There are limited numbers of literature about the integration of EC and enterprise systems in detail. Most of the studies in this area have focused on the factors which influence the adoption of EC by enterprise or other studies provide limited information about a specific platform or integration methodology in general. Therefore, this thesis is conducted to cover the technical details of EC and enterprise systems integration and covers both the adoption factors and integration solutions. In this study, many literature was reviewed and different solutions were investigated. Different enterprise integration approaches as well as most popular integration technologies were investigated. Moreover, various methodologies of integrating EC and enterprise systems were studied in detail and different solutions were examined. In this study, the influential factors to adopt EC in enterprises were studied based on previous literature and categorized to technical, social, managerial, financial, and human resource factors. Moreover, integration technologies were categorized based on three levels of integration, which are data, application, and process. In addition, different integration approaches were identified and categorized based on their communication and platform. Also, different EC integration solutions were investigated and categorized based on the identified integration approaches. By considering different aspects of integration, this study is a great asset to the architectures, developers, and system integrators in order to integrate and adopt EC with enterprise systems.