Optimización de un nuevo método de preparación de óxidos mixtos tipo perovskita con vacantes de oxígeno.

Se han optimizado las condiciones para la deslitiación de compuestos de fórmula general La2/3-xLi3xTiO3 así como las de la posterior termólisis de compuestos de fórmula general La2/3-xTiO3-3x(OH)3x. En ambos procesos se mantiene la estructura perovskita cúbica Pm3m. Estudios preliminares de conductividad eléctrica indican que los compuestos La2/3-xTiO3-3x/2 obtenidos mediante química suave a partir de la perovskita de lantano y litio se comportan como semiconductores.

Highly textured Sr, Nb, co-doped BiFeO3 thin films grown on SrRuO3/Si substrates by rf-sputtering

In this study, (011)-highly oriented Sr, Nb co-doped BiFeO3 (BFO) thin films were successfully grown on SrRuO3/Si substrates by rf-magnetron sputtering. The presence of parasite magnetic phases was ruled out based on the high resolution x-ray diffraction data. BFO films exhibited a columnar-like grain growth with rms surface roughness values of 5.3 nm and average grain sizes of 65-70 nm for samples with different thicknesses. Remanent polarization values (2Pr) of 54 lC cm 2 at room temperature were found for the BFO films with a ferroelectric behavior characteristic of an asymmetric device structure. Analysis of the leakage mechanisms for this structure in negative bias suggests Schottky injection and a dominant Poole-Frenkel trap-limited conduction at room temperature. Oxygen vacancies and Fe3þ/Fe2þ trap centers are consistent with the surface chemical bonding states analysis from x-ray photoelectron spectroscopy data. The (011)-BFO/ SrRuO3/Si film structure exhibits a strong magnetic interaction at the interface between the multiferroic film and the substrate layer where an enhanced ferromagnetic response at 5 K was observed. Zero-field cooled (ZFC) and field cooled (FC) magnetization curves of this film system revealed a possible spin glass behavior at spin freezing temperatures below 30 K depending on the BFO film thickness.

Assessment of dissolution techniques for the analysis of ceramic samples by plasma spectrometry

In this study, 13 ceramic samples were subjected to dissolution using three different procedures: (a) acid attack in open PTFE vessels with a mixture of HF-HClO4, (b) fusion of the sample with lithium metaborate and (c) microwave digestion in PTFE bombs. The samples used in the study had been previously analyzed by neutron activation analysis (NAA), X-ray fluorescence (XRF) and X-ray diffraction (XRD) and they cover a wide range of ceramics fired in different atmospheres and temperatures as well as different mineralogical and chemical compositions. The effectiveness of each procedure is evaluated in terms of its ability to dissolve the various mineralogical phases of the samples, of the number of elements that can be determined and of the time needed for the whole scheme of analysis to be completed.

Keraamisten teräpalojen käyttö niukkaseosteisten terästen lastuamiseen normaaleissa toimitustiloissa

Tämän tutkimuksen tavoitteena oli tutkia keraamisten kääntöterien soveltuvuus niukkaseosteräksille ja M-käsittelyn vaikutus teränkestoaikoihin. Lisäksi tavoitteena oli tutkia keraamiseosten erityisominaisuudet ja muodostaa käsitys keraamisilla kääntöterillä sorvaamisen erityisvaatimuksista. Kirjallisuusosassa selvitettiin tutkimushetkellä saatavissa olleet keraamiset teräaineseokset ja niiden ominaisuudet sekä selvitettiin keraamisten kääntöterien viimeaikaiset kehitystrendit. Lastuamistutkimus toteutettiin standardin ISO 3685:1993 mukaisesti, minkä lisäksi mitattiin lastuamisvoimat ja tehtiin kokeessa käytetyille terille lastunmurtokoe. Koemateriaalit olivat Imatra Steelin GreenCut, Hydax 25, M-käsittelemätön 42CrMo4 ja M-käsitelty MoC410M. Kokeissa käytetyt kääntöterät olivat eri valmistajien alumiinioksiditeriä, titaanikarbidiseostettuja alumiinioksiditeriä, kuituvahvisteisia ja yksi puhdas titaanikarbidiseosteinen terä. Koetulosten perusteella hyvän teränkestoajan saavuttamiseksi on tärkeää valita oikea keraamiseos ja sille soveltuvat parametrit. Oikein valituilla parametreilla M-terästä sorvattaessa tulokset ylittävät kovametalleilla saavutettavissa olevat arvot. Tulosten perusteella niukkaseostettujen terästen sorvaus onnistuu hyvin keraamisilla kääntöterillä, mutta kovametallisorvaukseen verrattuna syöttöä on laskettava ja lastuamisnopeutta lisättävä. Tämän työn tuloksia voidaan soveltaa sopivissa olosuhteissa toteutettavassa kappaletavaratuotannossa. Sovelluksen onnistuminen vaatii tukevat työstöolosuhteet ja riittävien lastuamisnopeuksien saavuttamisen.

Influencia de la atmosfera de sinterizacion en la estabilidad termica de ceramicas de hidroxiapatita reforzadas con circona

En este trabajo se estudia la influencia de la atmósfera de sinterización sobre la estabilidad térmica de cerámicas de hidroxiapatita (HA) reforzadas con partículas de circona parcialmente estabilizada con magnesia (Mg-PSZ). Los cuerpos verdes fueron obtenidos por prensado uniaxial y las sinterizaciones se realizaron en aire y en oxígeno húmedo. El estudio por difracción de rayos-X y espectroscopía infrarroja permitió comprobar que la atmósfera húmeda evita la descomposición de la hidroxiapatita, todo lo contrario a lo que sucede en aire donde es evidente la presencia del zirconato cálcico (CZ) en la interfaz entre la partícula de circona y la matriz de HA. La caracterización microestructural de los materiales por Microscopía Electrónica de Barrido permitió apreciar el desarrollo de tamaño de grano de los materiales sinterizados. El estudio del comportamiento mecánico mediante ensayos de indentación reveló un aumento de la tenacidad a la fractura en el caso de los materiales que presentaban Mg-PSZ con respecto a la HA pura.

Utilisation des céramiques biphasées dans les pertes de substance osseuse acétabulaire sévères dans les reprises de prothèse totale de hanche (PTH) : étude de 22 cas avec suivi à long terme

Management of bone loss in revision total hip replacement remains a challenge. To eliminate any immunological or infectious problem and so to try to improve the long-term results obtained with allografts, the authors used synthetic ceramics as bone substitutes since 1995. We reviewed 13 of the patients of our study, we previously reported in 2005 (Schwartz and Bordei in Eur J Orthop Surg Traumatol 15: 191 2005), which was a pro- spective cohort of thirty-two cases of acetabular revision reconstruction, with a mean follow-up of 14.4 years yet (from 9 to 16 years). Clinical results were assessed according to Oxford scale and Postel and Merle d'Aubigne (PMA) scale. Since 2005, no specific complications were noted. The average PMA functional hip score was 14.9 (vs. 9.2 before revision) at follow-up over 9 years. Nine patients still alive in 2013 were seen again by a surgeon, which was not the operator, with a mean follow-up of 15.3 years: Their Oxford average score was 40.3. Radio- logical assessment affirmed a good integration of the sub- stitutes in bone without any edging in all cases. A progressive invasion of the ceramics by bone can be seen on the X-ray. We conclude that about 15 years of average delay, which is a significant follow-up in orthopedic sur- gery, the outcomes without specific complications are satisfactory and allow one to go with these materials in total hip revision surgery.

Disseny amforal i canvi tecnològic al voltant del canvi d'era: L'aportació de l'Anàlisi d'Elements Finits

[spa] Mediante el Análisis de Elementos Finitos es posible evaluar un diseño cerámico en función de su tipologia y de las propiedades mecánicas del material. Su aplicación permite considerar los factores tecnológicos que puedan haber condicionado el cambio de una tipologia cerámica. Este análisis se ilustra con los primeros tipos anfóricos romanos producidos en la actual Cataluña (Dressel 1, Tarraconense 1 y Pascuai 7).

Domain matched epitaxial growth of Bi1.5Zn1Nb1.5O7 thin films by pulsed laser deposition

Bi1.5Zn1Nb1.5O7 (BZN) epitaxial thin films were grown by pulsed laser deposition on Al2O3 with a double ZnO buffer layer through domain matching epitaxy (DME) mechanism. The pole figure analysis and reciprocal space mapping revealed the single crystalline nature of the thin film. The pole figure analysis also shows a 60º twinning for the (222) oriented crystals. Sharp intense spots in the SAED pattern also indicate the high crystalline nature of BZN thin film. The Fourier filtered HRTEM images of the BZN-ZnO interface confirms the domain matched epitaxy of BZN with ZnO buffer. An electric field dependent dielectric tunability of 68% was obtained for the BZN thin films with inter digital capacitors patterned over the film.

Caracterizacion por difraccion de rayos-X, analisis termico y espectroscopia Raman de los cristales mixtos Li(NH4)(1-x)KxSO4

En este trabajo se estudia la preparació n y caracterizació n de las fases de los cristales mixtos de f órmula Li(NH4)1-xKxSO4. La caracterizacói n se ha efectuado por aná lisis té rmico con DSC y ATD, difracci ón de rayos-X sobre polvo cristalino con temperatura variable, difracci n de rayos-X sobre muestra monocristalina a temperatura variable a fin de determina su estructura cristalina y por espectroscop"a Raman a temperatura variable. Se han obtenido dos tipos de fases. Una soluci n s lida con 0.94 < x < 1 que presenta los mismos tipos estructurales que el LiKSO4, pero seg n el m todo de cristalizaci n pueden aparecer nuevas fases que no presenta el LiKSO4. El segundo tipo de compuesto tiene por f rmula Li(NH4)0.53K0.47SO4, el cual presenta una estructura hexagonal con par metro a » 3 aLiKSO4. Este compuesto tiene por encima de la temperatura ambiente una sola transici n a 463K.

Estudio del sistema Li2SO4-Na2SO4. Diagrama de fases y caracterizacion del LiNaSO4

Se presenta un estudio exhaustivo del diagrama de fase del sistema binario Li2SO4-Na2SO4. El diagrama de fases se determinó mediante termo-difractometría de rayos-X en muestras de polvo y calorimetría ATD. Se obtiene una nueva fase de fórmula Li2-xNaxSO4, con 1 ¿ x ¿ 1.22. La estructura cristalina de ß-LiNaSO4 se determinó por difracción de rayos-X sobre un monocristal. Este estudio muestra que los cristales usualmente se maclan cuando el crecimiento es por solución, lo cual explica la baja polarización espontánea. Se explica la dispersión Raman de los compuestos Li2SO4, Na2SO4 y LiNaSO4, a partir de los datos estructurales. Las medidas experimentales se han efectuado a diferentes velocidades de calentamiento y enfriamiento.

Efeito da adição de Na2O na viscosidade e devitrificação do vidro obtido a partir de cinzas volantes e Li2O

Glass-ceramic materials can be produced by the addition of LiO2 to fly ashes disposible in Southern Brazil. These glass-ceramics are based on the Al2O3-SiO2-Li 2O system. The high viscosity of the obtained glasses, however, makes forming useful articles with these materials difficult. In this study we investigate the effect of adding low cost Na2CO3 on the melt viscosity and on the nature of the developed crystalline phases. It was intended that the ultimate crystalline phase (LiAlSi3O8) should not be altered. With additions up to 3 wt. % Na2CO3, the viscosity was apparently lowered and no new crystalline phase were detected.

Rotas de síntese e a homogeneidade dos precursores de mulita e cordierita

Multicomponent ceramics are mainly synthesized by conventional solid-state reaction route and sol-gel routes. In the sol-gel route, colloidal or polymeric gel are envolved. In this work, some principles of the chemistry of theses routes are discused and it is ilustrated a variety of strategies for obtaining a homogeneous multicomponent precursors.

Calcium phosphate biomaterials from marine algae. Hydrothermal synthesis and characterisation

Calcium phosphate compounds such as Hydroxyapatite (HAp) were prepared by hydrothermal synthesis with phycogenic CaCO3 as starting material. Material obtained was characterised by usual methods (XRD, FTIR, TG, N2-adsorption, SEM and EDX) in order to study its physical-chemical characteristics. The prepared HAp showed that it may be suitable for use as a biomaterial.

Classificação de cerâmicas arqueológicas da Bacia Amazônica

In order to elucidate the traditional classification of archaeological artefacts, a multielemental analytical method for characterisation of its micro and macro chemical constituents. combined with statistical multivariate analysis for classification, were used. Instrumental thermal neutron activation analysis, for elemental chemical determination, and three statistical methods: discriminant, cluster and modified cluster analysis were applied. The statistical results obtained for the samples from Iquiri, Quinari and Xapuri archaeological phases were in good agreement with the conventional archaeological classification. Iaco and Jacuru archaeological phase were not characterised as homogenous groups. Iquiri phase were the most distinct in relation to the other analysed groups. An homogeneous group for 54% collected samples at the Los Angeles site was also found, this could be characterised as a new archaeological phase.

Caracterização de cinza de casca de arroz para uso como matéria-prima na fabricação de refratários de sílica

The characterization of rice husk ash, a deriving by-product of the burning of the rice husk during the rice processing is the object of this study. This by-product, for being rich in silica, can be an important raw material for the production of siliceous ceramics, such as thermal insulators and refractory. A combination of surface analysis, thermal analysis and microscopy analysis techniques was used for the characterization. The characterized by-product presented as main component the silica, under amorphous form, with a maximum content of alkalis around 1%, features that become it potentially interesting for the production of ceramic materials.