Temperature rise during adhesive and composite polymerization with different light-curing sources

AIM: This study evaluated the temperature rise of the adhesive system Single Bond (SB) and the composite resins Filtek Z350 flow (Z) and Filtek Supreme (S), when polymerized by light-emitting diode (LED XL 3000) and quartz-tungsten halogen (QTH Biolux). METHODS: Class V cavities (3 yen2 mm) were prepared in 80 bovine incisors under standardized conditions. The patients were divided as follows: G1: Control; G2: SB; G3: SB + Z; G4: SB + S. The groups were subdivided into two groups for polymerization (A: QTH, B: LED). Light curing was performed for 40 s and measurement of temperature changes during polymerization was performed with a thermocouple positioned inside the pulp chamber. Data were statistically analyzed using ANOVA and Tukey tests. RESULTS: The factors material (P<0.00001) and curing unit (P<0.00001) had significant influence on temperature rise. The lowest temperature increase (0.15 degrees C) was recorded in G2 B and the highest was induced in G1 A (0.75 degrees C, P<0.05). In all groups, lower pulp chamber temperature measurements were obtained when using LED compared to QTH (P<0.05). CONCLUSION: QTH caused greater increases in tooth temperature than LED. However, both sources did not increase pulpal temperature above the critical value that may cause pulpal damage.

Conductive nanocomposites based on cellulose nanofibrils coated with polyaniline-DBSA via in situ polymerization

Cellulose nanofibrils (CNF) were extracted by acid hydrolysis from cotton microfibrils and nanocomposites with polyaniline doped with dodecyl benzenesulphonic acid (PANI-DBSA) were obtained by in situ polymerization of aniline onto CNF. The ratios between DBSA to aniline and aniline to oxidant were varied in situ and the nanocomposites characterized by four probe DC electrical conductivity, ultraviolet-visible-near infrared (UV-Vis - NIR) and Fourier-transform infrared (FTIR) spectroscopies and X-ray diffraction (XRD). FTIR and UV-Vis/NIR characterization confirmed the polymerization of PANI onto CNF surfaces. Electrical conductivity of about 10 -1 S/cm was achieved for the composites; conductivity was mostly independent of DBSA/aniline (between 2 and 4) and aniline/oxidant (between 1 and 5) molar ratios. X-ray patterns of the samples showed crystalline peaks characteristic of cellulose I for CNF samples, and a mixture of both characteristic peaks of PANI and CNF for the nanocomposites. Field emission scanning electron microscopy (FESEM) characterization corroborated the abovementioned results showing that PANI coated the surface of the nanofibrils. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Soursop (Annona muricata L.) and sugar apple (Annona squamosa L.): Antioxidant activity, fatty acids profile and determination of tocopherols

Purpose: This study aims to analyze the soursop and sugar apple seeds as to its composition, to evaluate the antioxidant potential of seeds extract and characterize the oil extracted from them, regarding the fatty acids profile and content of tocopherols. Design/methodology/approach: To obtain the extracts, dried and crushed seeds were extracted with ethanol for 30 minutes, at a ratio of 1:3 (m/m, seed: ethyl alcohol) under continuous stirring at room temperature. Then, the mixture was filtered and the supernatants subjected to rotoevaporator at 40°C aiming to determine, by direct weighing, the yields of dry extracts. Findings: According to the results, the soursop and sugar apple seeds constituted significant sources of lipids, proteins and carbohydrates and can therefore be used in food and feed, and offer relevant antioxidant activity of phenolic compounds. The oil seeds are a good source of unsaturated fatty acids, especially oleic and linoleic acids and they have significant amounts of total tocopherol. Research limitations/implications: Implications are the identification of bioactive compounds extracted from seeds of tropical and subtropical fruits, and to prevent certain types of diseases. Practical implications: The information presented might be directly used for developing of functional foods such as fruits. Originality/value: The article tries to identify new source of compounds extracted from fruits. © Emerald Group Publishing Limited.

Electrochemical studies based on local interfacial ph changes of gold nanoparticles immobilized on polystyrene brushes

The electrochemical behavior of polystyrene modified with gold nanoparticle (Au NPs) was investigated in terms of pH-responsive polymer brush. A pH-responsive of modified polymer brush from tethered polystyrene was prepared and used for selective gating transport of anions andcations across the thin-film. An ITO-coated glass electrode was used as substrate and applied to study the switchable permeability of the polymer brush triggered by changes in pH of the aqueous environment. The pH-sensitive behavior of the polymer brush interface has been demonstrated by means of cyclic voltammetry (CV) and Localized Surface Plasmon Resonance (LSPR). CV experiments showed at ph values of 4 and 8 induces swelling and shrinking of the grafted polymer brushes, respectively, and this behavior is fast and reversible. LSPR measurements showed a blue shift of 33 nm in the surface resonance band changes by local pH. The paper brings an easy methodology to fabrication a variety of nanosensors based on the polymer brushes-nanoparticle assemblies. © 2013 by ESG.

Durability of Adhesion between Feldspathic Ceramic and Resin Cements: Effect of Adhesive Resin, Polymerization Mode of Resin Cement, and Aging

Purpose: Adhesive cementation is an important step for restorations made of feldspathic ceramic as it increases the strength of such materials. Incorrect selection of the adhesive resin and the resin cement to adhere to the ceramic surface and their durability against aging can affect the adhesion between these materials and the clinical performance. This study evaluated the effect of adhesive resins with different pHs, resin cements with different polymerization modes, and aging on the bond strength to feldspathic ceramic. Materials and Methods: One surface of feldspathic ceramic blocks (VM7) (N = 90) (6.4 × 6.4 × 4.8 mm3) was conditioned with 10% hydrofluoric acid for 20 seconds, washed/dried, and silanized. Three adhesive resins (Scotchbond Multi-Purpose Plus [SBMP], pH: 5.6; Single Bond [SB], pH: 3.4; and Prime&Bond NT [NT], pH: 1.7) were applied on the ceramic surfaces (n = 30 per adhesive). For each adhesive group, three resin cements with different polymerization modes were applied (n = 10 per cement): photo-polymerized (Variolink II base), dual polymerized (Variolink II base + catalyst), and chemically polymerized (C&B). The bonded ceramic blocks were stored in water (37°C) for 24 hours and sectioned to produce beam specimens (cross-sectional bonded area: 1 ± 0.1 mm2). The beams of each block were randomly divided into two conditions: Dry, microtensile test immediately after cutting; TC, test was performed after thermocycling (12,000×, 5°C to 55°C) and water storage at 37°C for 150 days. Considering the three factors of the study (adhesive [3 levels], resin cement [3 levels], aging [2 levels]), 18 groups were studied. The microtensile bond strength data were analyzed using 3-way ANOVA and Tukey's post hoc test (α= 0.05). Results: Adhesive resin type (p < 0.001) and the resin cement affected the mean bond strength (p= 0.0003) (3-way ANOVA). The NT adhesive associated with the chemically polymerized resin cement in both dry (8.8 ± 6.8 MPa) and aged conditions (6.9 ± 5.9 MPa) presented statistically lower bond strength results, while the SBMP adhesive resin, regardless of the resin cement type, presented the highest results (15.4 to 18.5 and 14.3 to 18.9 MPa) in both dry and aged conditions, respectively (Tukey's test). Conclusion: Application of a low-pH adhesive resin onto a hydrofluoric acid etched and silanized feldspathic ceramic surface in combination with chemically polymerized resin cement did not deliver favorable results. The use of adhesive resin with high pH could be clinically advised for the photo-, dual-, and chemically polymerized resin cements tested. © 2012 by the American College of Prosthodontists.

Sleeving nanocelluloses by admicellar polymerization

This investigation reports the first application of admicellar polymerization to cellulose nanofibers in the form of bacterial cellulose, microfibrillated cellulose, and cellulose nanowhiskers using styrene and ethyl acrylate. The success of this physical sleeving was assessed by SEM, FTIR, and contact angle measurements, providing an original and simple approach to the modification of cellulose nanofibers in their pristine aqueous environment. © 2013 The Authors. Published by Elsevier Inc.

Management for the development of high-mountain river basins in the Andean region

Includes bibliography

Development and management of upland watersheds and high-mountain zones in Latin America

Includes bibliography

Strategies for the development and management of high-mountain watersheds and zones in Latin America: a critical analysis

Publicado anteriormente en español con el símbolo LC/G.1533-P

Mountain watershed management in the development and conservation of natural resources

Includes bibliography

Management strategies for development of high-mountain river basins in the Andean region

Includes bibliography

Análise de similaridades e diferenças no uso de marcadores de reformulação e padrões lexicais em Family ties, The apple in the dark e Soulstorm, de Clarice Lispector, e The red house, de Lya Luft

Pós-graduação em Estudos Linguísticos - IBILCE

Anthocyanins, pigment stability and antioxidant activity in jabuticaba [myrciaria cauliflora (Mart) O Berg]

Different solvents were evaluated for the extraction of jabuticaba anthocyanin pigments, identifying, quantifying and verifying the stability of the anthocyanins, as well as the conduction of three antioxidant activity assays and determination of the vitamin C levels. The maceration with ethanol acidified with HCl 1.5 mol L-1 (85:15) provides better pigment extraction and stability. The skin is anthocyanin rich, presenting 1.59 and 2.06 g 100 g-1 of dry matter in the Paulista and Sabará varieties, respectively. Cyanidin 3-glucoside is the majority pigment of the skins, followed by delphinidin 3-glucoside. The highest level of vitamin C was found in the skins and seeds of both varieties. It was verified that the skins, presented more antioxidant activity, in free radical capture, as well as in retarding the lipid oxidation process.

Effect of calcium on the structural properties of Ba(1-x)Ca (x) TiO3 particles synthesized by complex polymerization method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Fabrication of Zinc Oxide Nanowires/Polymer Composites by Two-Photon Polymerization

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)