Studies of Liquid-liquid Separation in Fibre Coalescer

This thesis focuses on fibre coalescers whose efficiency is based on the surface properties/characteristics. They have the ability to preferentially wet or interact with one or more of the fluids to be separated. Thus, the interfacial phenomena governing the separation efficiency of the coalescers is investigated depending on physical factors such as flowrates, phase ratios and coalescer packing density. Design of process equipment to produce and separate of the emulsions was carried out.The experimentation was carried out to test the separation efficiency of the coalescing medias, namely fibreglass, polyester I and polyester II. The performances of the coalescing medias were assessed via droplet size information. In conclusion, the objectives (design of process equipment and experimentation) were achieved. Fibre glass was the best coalescing media, next was polyester I and then finally polyester II. Droplets sizes increased with decreased flowrates and increased packing density of the coalescer. Phase ratio had effect on the droplet sizes of the feed but had no effect on the coalescence of droplets of the feed.

Ultra-trace monitoring of copper in environmental and biological samples by inductively coupled plasma atomic emission spectrometry after separation and preconcentration by using octadecyl silica membrane disks modified by a new schiff's base

Ultra-trace amounts of Cu(II) were separated and preconcentrated by solid phase extraction on octadecyl-bonded silica membrane disks modified with a new Schiff,s base (Bis- (2-Hydroxyacetophenone) -2,2-dimethyl-1,3-propanediimine) (SBTD) followed by elution and inductively coupled plasma atomic emission spectrometric detection. The method was applied as a separation and detection method for copper(II) in environmental and biological samples. Extraction efficiency and the influence of sample matrix, flow rate, pH, and type and minimum amount of stripping acid were investigated. The concentration factor and detection limit of the proposed method are 500 and 12.5 pg mL-1, respectively.

Flow analysis by using solenoid valves for As(III) determination in natural waters by an on-line separation and pre-concentration system coupled to a tungsten coil atomizer

A flow system coupled to a tungsten coil atomizer in an atomic absorption spectrometer (TCA-AAS) was developed for As(III) determination in waters, by extraction with sodium diethyldithiocarbamate (NaDDTC) as complexing agent, and by sorption of the As(III)-DDTC complex in a micro-column filled with 5 mg C18 reversed phase (10 µL dry sorbent), followed by elution with ethanol. A complete pre-concentration/elution cycle took 208 s, with 30 s sample load time (1.7 mL) and 4 s elution time (71 µL). The interface and software for the synchronous control of two peristaltic pumps (RUN/ STOP), an autosampler arm, seven solenoid valves, one injection valve, the electrothermal atomizer and the spectrometer Read function were constructed. The system was characterized and validated by analytical recovery studies performed both in synthetic solutions and in natural waters. Using a 30 s pre-concentration period, the working curve was linear between 0.25 and 6.0 µg L-1 (r = 0.9976), the retention efficiency was 94±1% (6.0 µg L-1), and the pre-concentration coefficient was 28.9. The characteristic mass was 58 pg, the mean repeatability (expressed as the variation coefficient) was 3.4% (n=5), the detection limit was 0.058 µg L-1 (4.1 pg in 71 µL of eluate injected into the coil), and the mean analytical recovery in natural waters was 92.6 ± 9.5 % (n=15). The procedure is simple, economic, less prone to sample loss and contamination and the useful lifetime of the micro-column was between 200-300 pre-concentration cycles.

Early relationship between very preterm infant and mother: The role of infant, maternal and dyadic factors

Pienipainoisen keskosen ja äidin varhainen suhde: Lapsen, äidin ja dyadisten muuttujien vaikutus Tämän tutkimuksen tavoitteena oli tutkia keskosvauvan ja äidin varhaista suhdetta. Tutkimuksessa selvitettiin myös vauvan itkukäyttäytymisen, vauvan sylissä olon ja äidin masentuneisuuden yhteyttä äidin ja keskosvauvan varhaiseen suhteeseen. Tutkimusryhmät koostuivat 32:sta (tutkimus I-II) ja 38:sta (tutkimus III-IV) keskosena syntyneestä vauvasta (syntymäpaino < 1501 g tai GI < 32 viikkoa) sekä 46:sta täysiaikaisena syntyneestä terveestä verrokkivauvasta. Lapsen ja äidin vuorovaikutusta arvioitiin 6 ja 12 kuukauden iässä (korjattu ikä) PCERAmenetelmällä. Äidin mielikuvia lapsestaan tutkittiin WMCI-haastattelulla, kun lapsi oli 12 kuukautta. Baby Day Diary -menetelmää käytettiin vauvan itkukäyttäytymisen ja sylissä olon keston mittaamisessa vauvan ollessa 5 kuukautta. Äidin masentuneisuutta arvioitiin EDPS-lomakkeella, kun lapsi oli 6 kuukautta. Tulokset osoittivat, että turvallisten kiintymyssuhdemielikuvien määrä tai vuorovaikutuksen laatu eivät keskosvauvan äideillä eronneet täysiaikaisina syntyneiden vauvojen äitien vastaavista. Ryhmien välillä ei löytynyt eroja myöskään dyadisen vuorovaikutuksen laadussa. Keskosena syntyneet lapset olivat kuitenkin vetäytyvämpiä ja heillä oli laadullisesti heikommat keskittymisen ja leikin taidot vuorovaikutustilanteessa 12 kuukauden iässä täysiaikaisina syntyneisiin lapsiin nähden. Lisäksi äidin masentuneisuus ja lapsen pitkittynyt itkuisuus olivat negatiivisessa yhteydessä vuorovaikutuksen laatuun keskosvauvojen ryhmässä. Vauvan itkukertojen määrän, sylissä olon keston sekä äidin ja vauvan vuorovaikutuksen laadun välillä löytyi positiivinen yhteys ainoastaan keskosena syntyneiden lasten ryhmässä. Tulostemme perusteelle toteamme, että lapsen ennenaikainen syntymä itsessään ei näytä muodostavan riskiä äidin vuorovaikutuksen laadulle tai turvalliselle kiintymyssuhteelle. Yhdessä muiden riskitekijöiden kanssa keskosuus kuitenkin altistaa vauvat ja heidän äitinsä varhaisen vuorovaikutuksen ongelmille. Lisäksi tuloksemme viittaavat siihen, että vauvan itku ja siitä seuraava sylissä olo toimivat suojaavana mekanismina pienipainoisen keskosen ja äidin varhaisessa suhteessa.

Preparative separation of flavonoids from the medicinal plant Davilla elliptica St. Hill. by high-speed counter-current chromatography

High-speed counter-current chromatography (HSCCC) is a major tool for the fast separation of natural products from plants. It was used for the preparative isolation of the flavonoid monoglucosides present in the aerial parts of the Davilla elliptica St. Hill. (Dilleniaceae). This species is used in Brazilian folk medicine for the treatment of gastric disorders. The optimum solvent system used was composed of a mixture of ethyl acetate-n-propanol-water (140:8:80, v/v/v) and led to a successful separation of quercetin-3-O-alpha-L-rhamnopyranoside and myricetin-3-O-alpha-L-rhamnopyranoside in approximately 3.0 hours with purity higher than 95%. Identification was performed by ¹H NMR, 13C NMR and HPLC-UV-DAD analyses.

Cue-elicited anxiety and craving for food using virtual reality scenarios

Cue exposure therapy has been reported to be an effective intervention for reducing binge eating behavior in patients with eating disorders and obesity. However, in vivo food exposure conducted in the therapist's office presents logistical problems and lacks ecological validity. This study proposes the use of virtual reality technology as an alternative to in vivo exposure, and assesses the ability of different virtual environments to elicit anxiety and craving for food in a non-clinical sample. The results show that exposure to virtual environments provokes changes in reported craving for food. High-calorie food cues are the ones that elicit the highest increases in craving.

Mood and anxiety disorders across the adult lifespan: a European perspective

BACKGROUND: The World Mental Health Survey Initiative (WMHSI) has advanced our understanding of mental disorders by providing data suitable for analysis across many countries. However, these data have not yet been fully explored from a cross-national lifespan perspective. In particular, there is a shortage of research on the relationship between mood and anxiety disorders and age across countries. In this study we used multigroup methods to model the distribution of 12-month DSM-IV/CIDI mood and anxiety disorders across the adult lifespan in relation to determinants of mental health in 10 European Union (EU) countries. METHOD: Logistic regression was used to model the odds of any mood or any anxiety disorder as a function of age, gender, marital status, urbanicity and employment using a multigroup approach (n = 35500). This allowed for the testing of specific lifespan hypotheses across participating countries. RESULTS: No simple geographical pattern exists with which to describe the relationship between 12-month prevalence of mood and anxiety disorders and age. Of the adults sampled, very few aged ≥ 80 years met DSM-IV diagnostic criteria for these disorders. The associations between these disorders and key sociodemographic variables were relatively homogeneous across countries after adjusting for age. CONCLUSIONS: Further research is required to confirm that there are indeed stages in the lifespan where the reported prevalence of mental disorders is low, such as among younger adults in the East and older adults in the West. This project illustrates the difficulties in conducting research among different age groups simultaneously.

Development of a flotation method for preconcentration-separation of trace amounts of some metal ions in plant tissues prior to their FAAS determinations

An efficient flotation method based on the combination of flame atomic absorption spectrometry (FAAS) and separation and preconcentration step for determination of Cr3+, Cu 2+, Co2+, Ni2+, Zn2+, Cd 2+, Fe3+ and Pb2+ ions in various real samples by the possibility of applying bis(2-hydroxyacetophenone)-1,4-butanediimine (BHABDI) as a new collector was studied. The influence of pH, amount of BHABDI as collector, sample matrix, type and amount of eluting agent, type and amount of surfactant as floating agent, ionic strength and air flow rates i.e. variables affecting the efficiency of the extraction system was evaluated. It is ascertained that metal ions such as iron can be separated simultaneously from matrix in the presence of 0.012 mM ligand, 0.025% (w/v) of CTAB to a test sample of 750 mL at pH 6.5. These ions can be eluted quantitatively with 6 mL of 1.0 mol L-1 HNO3 in methanol which lead to the enrichment factor of 125. The detection limits for analyte ions were in the range of 1.3-2.4 ng mL-1. The method has been successfully applied for determination of trace amounts of ions in various real samples.

Separation and preconcentration trace amounts of gold by using modified organo nanoclay closite 15A

The application of organo nanoclay 5-(4-dimethylamino-benzylidene) rhodanine-immobilized as a new, easily prepared, and stable solid sorbent for preconcentration trace amounts of Au(III) ions in aqueous solution is presented. The sorption of Au(III) ions was quantitative in the pH range of 2-4, and quantitative desorption occurred instantaneously with 10.0 mL of a mixture containing 0.5 mol L-1 Na2S2O3 and KSCN. Various parameters, such as the effect of pH, breakthrough volume, extraction time, and interference of a large number of anions and cations have been studied. The proposed method has been applied for determination of trace amount of gold in water samples.

Preparative separation and purification of sesquiterpenoids from tussilago farfara l. by high-speed counter-current chromatography

Preparative high-speed counter-current chromatography (HSCCC) was successfully applied for separation and purification of sesquiterpenoids from an extract of Tussilago farfara L. with a two-phase solvent system composed of n-hexane-ethyl acetate- methanol-water (1:0.5:1.1:0.3, v/v/v/v). The separation produced a total of 32 mg of tussilagone, 18 mg of 14-acetoxy-7β-(3'-ethyl cis-crotonoyloxy)-lα-(2'-methyl butyryloxy)-notonipetranone and 21 mg of 7β-(3'-ethyl cis-crotonoyloxy)-lα-(2'- methyl butyryloxy)-3,14-dehydro-Z-notonipetranone from 500 mg of the crude extract in one step separation with the purity of 99.5, 99.4 and 99.1%, respectively, as determined by HPLC. The structures of these compounds were identified by ESI-MS, ¹H-NMR and 13C-NMR.

Dispersive liquid-liquid microextraction for the simultaneous separation of trace amounts of zinc and cadmium ions in water samples prior to flame atomic absorption spectrometry determination

In the proposed method, carbon tetrachloride and ethanol were used as extraction and dispersive solvents. Several factors that may be affected on the extraction process, such as extraction solvent, disperser solvent, the volume of extraction and disperser solvent, pH of the aqueous solution and extraction time were optimized. Under the optimal conditions, linearity was maintained between 1.0 ng mL-1 to 1.5 mg mL-1 for zinc and 1.0 ng mL-1 to 0.4 mg mL-1 for cadmium. The proposed method has been applied for determination of trace amount of zinc and cadmium in standard and water samples with satisfactory results.

Separation and characterization of asphaltenic subfractions

The structure of the various asphaltenic subfractions found in crude oil was evaluated. For this purpose, C5 asphaltenes were extracted from an asphaltic residue using n-pentane as the flocculant solvent. The different subfractions were isolated from the C5 asphaltenes by the difference in solubility in different solvents. These were characterized by infrared spectroscopy, nuclear magnetic resonance, X-ray fluorescence, elementary analysis and mass spectrometry. The results confirmed that the subfractions extracted with higher alkanes had greater aromaticity and molar mass. However, small solubility variations between the subfractions were attributed mainly to the variation in the concentrations of cyclical hydrocarbon compounds and metals.

Dispersive liquid-liquid microextraction based on solidification of floating organic drop for simultaneous separation/preconcentration of nickel, cobalt and copper prior to determination by electrothermal atomic absorption spectrometry

A dispersive liquid-liquid microextraction based on solidification of floating organic drop for simultaneous extraction of trace amounts of nickel, cobalt and copper followed by their determination with electrothermal atomic absorption spectrometry was developed. 300 µL of acetone and 1-undecanol was injected into an aqueous sample containing diethyldithiocarbamate complexes of metal ions. For a sample volume of 10 mL, enrichment factors of 277, 270 and 300 and detection limits of 1.2, 1.1 and 1 ng L-1 for nickel, cobalt and copper were obtained, respectively. The method was applied to the extraction and determination of these metals in different water samples.

Preparative separation and purification of bufadienolides from ChanSu by high-speed counter-current chromatography combined with preparative HPLC

Eight bufadienolides were successfully isolated and purified from ChanSu by high-speed counter-current chromatography (HSCCC) combined with preparative HPLC (prep-HPLC). First, a stepwise elution mode of HSCCC with the solvent system composed of petroleum ether - ethyl acetate - methanol - water (4:6:4:6, 4:6:5:5, v/v) was employed and four bufadienolides, two partially purified fractions were obtained from 200 mg of crude extract. The partially purified fractions III and VI were then further separated by prep-HPLC, respectively, and another four bufadienolides were recovered. Their structures were confirmed by ESI-MS and ¹H-NMR spectra.

Separation and preconcentration of copper in environmental samples on Amberlite XAD-8 resin after complexation with a carbothioamide derivative

A new solid phase extraction (SPE) method has been developed for the selective separation and preconcentration of Cu (II) ions in food and water samples prior to its flame atomic absorption spectrometry determination. The method is based on the adsorption of the Cu(II) - 2-{[4-Amino-3-(4-methylphenyl-5-oxo-4,5-dihydro-1H-1,2,4-triazol-1-yl]acetyl}-N-phenyl hydrazinecarbothioamide complex on Amberlite XAD-8 resin. The metal complex retained on the resin was eluted with 7.5 mL of 2.0 mol L-1 HCl in acetone. The optimum conditions for the SPE of Cu(II) ions were investigated, and the method was subsequently applied to sea water, stream water, rice, tea, and tobacco samples for the determination of Cu(II) levels.