The potential of molecular imprinting as a biosensing devices for monitoring the CEA cancer biomarker

6th Graduate Student Symposium on Molecular Imprinting

A novel antibody-like material for breast cancer antigen CA15-3, used to track breast cancer by potentiometric transduction

This work presents the development of a low cost sensor device for the diagnosis of breast cancer in point-of-care, made with new synthetic biomimetic materials inside plasticized poly(vinyl chloride), PVC, membranes, for subsequent potentiometric detection. This concept was applied to target a conventional biomarker in breast cancer: Breast Cancer Antigen (CA15-3). The new biomimetic material was obtained by molecularly-imprinted technology. In this, a plastic antibody was obtained by polymerizing around the biomarker that acted as an obstacle to the growth of the polymeric matrix. The imprinted polymer was specifically synthetized by electropolymerization on an FTO conductive glass, by using cyclic voltammetry, including 40 cycles within -0.2 and 1.0 V. The reaction used for the polymerization included monomer (pyrrol, 5.0×10-3 mol/L) and protein (CA15-3, 100U/mL), all prepared in phosphate buffer saline (PBS), with a pH of 7.2 and 1% of ethylene glycol. The biomarker was removed from the imprinted sites by proteolytic action of proteinase K. The biomimetic material was employed in the construction of potentiometric sensors and tested with regard to its affinity and selectivity for binding CA15-3, by checking the analytical performance of the obtained electrodes. For this purpose, the biomimetic material was dispersed in plasticized PVC membranes, including or not a lipophilic ionic additive, and applied on a solid conductive support of graphite. The analytical behaviour was evaluated in buffer and in synthetic serum, with regard to linear range, limit of detection, repeatability, and reproducibility. This antibody-like material was tested in synthetic serum, and good results were obtained. The best devices were able to detect 5 times less CA15-3 than that required in clinical use. Selectivity assays were also performed, showing that the various serum components did not interfere with this biomarker. Overall, the potentiometric-based methods showed several advantages compared to other methods reported in the literature. The analytical process was simple, providing fast responses for a reduced amount of analyte, with low cost and feasible miniaturization. It also allowed the detection of a wide range of concentrations, diminishing the required efforts in previous sample pre-treating stages.

Sol-gel biomimetic material designed to target CEA cancer biomarker

1st ASPIC International Congress

A disposable glass-based immunosensor for monitoring the cancer biomarker CEA in urine

NanoPT 2014 International Conference, in Portugal, on February 12-14. Poster presentation based on topic Nanobio/Nanomedicine

Forest fire detection with a small fixed wing autonomous aerial vehicle

In this work a forest fire detection solution using small autonomous aerial vehicles is proposed. The FALCOS unmanned aerial vehicle developed for remote-monitoring purposes is described. This is a small size UAV with onboard vision processing and autonomous flight capabilities. A set of custom developed navigation sensors was developed for the vehicle. Fire detection is performed through the use of low cost digital cameras and near-infrared sensors. Test results for navigation and ignition detection in real scenario are presented.

Autonomous Surface Vehicle Docking Manoeuvre with Visual Information

This work presents a hybrid coordinated manoeuvre for docking an autonomous surface vehicle with an autonomous underwater vehicle. The control manoeuvre uses visual information to estimate the AUV relative position and attitude in relation to the ASV and steers the ASV in order to dock with the AUV. The AUV is assumed to be at surface with only a small fraction of its volume visible. The system implemented in the autonomous surface vehicle ROAZ, developed by LSA-ISEP to perform missions in river environment, test autonomous AUV docking capabilities and multiple AUV/ASV coordinated missions is presented. Information from a low cost embedded robotics vision system (LSAVision), along with inertial navigation sensors is fused in an extended Kalman filter and used to determine AUV relative position and orientation to the surface vehicle The real time vision processing system is described and results are presented in operational scenario.

Coordinated Maneuver for Gradient Search Using Multiple AUV's

OCEANS 2003. Proceedings (Volume:1 )

Comparative study of the topical effectiveness of the andiroba oil (Carapa guianensis) and DEET 50% as repellent for Aedes sp

DEET (N,N-diethyl-3-methylbenzamide) is nowadays the most effective mosquito repellent available, however, its use can present some topical and systemic side effects. Some botanical compositions, as Andiroba (Carapa guianensis), have been proved repellent properties at low cost and toxicity. An experimental study was driven involving four volunteers submitting their forearms covered with Andiroba oil at 100%, DEET 50%, refined soy oil, Andiroba oil 15% and in the absence of products, directly to healthy females of Aedes sp. The times of first and third bites were checked. The results showed that the median of the first bite without any product was 17.5s and the third bite, 40.0s. In the soy oil, the bites happened in 60.0s and 101.5s, in the presence of Andiroba oil 100%, in 56.0s and 142.5s and in Andiroba oil 15%, in 63.0s and 97.5s. The volunteers using DEET 50% had not received bites after 3600s in most of the experiments (p < 0.001 Wilcoxon). Pure Andiroba oil compared to the soy oil, forearm without product and Andiroba oil 15%, showed discreet superiority (p < 0.001 Wilcoxon). Our conclusion is that this study demonstrated that the pure Andiroba oil presents discreet repellent effect against bite of Aedes sp., being significantly inferior to DEET 50%.

Standard commercial education robotic platform: intermediate solution to teaching robotics

Teaching robotics to students at the beginning of their studies has become a huge challenge. Simulation environments can be an effective solution to that challenge where students can interact with simulated robots and have the first contact with robotic constraints. From our previous experience with simulation environments it was possible to observe that students with lower background knowledge in robotics where able to deal with a limited number of constraints, implement a simulated robotic platform and study several sensors. The question is: after this first phase what should be the best approach? Should the student start developing their own hardware? Hardware development is a very important part of an engineer's education but it can also be a difficult phase that could lead to discouragement and loss of motivation in some students. Considering the previous constraints and first year engineering students’ high abandonment rate it is important to develop teaching strategies to deal with this problem in a feasible way. The solution that we propose is the integration of a low-cost standard robotic platform WowWee Rovio as an intermediate solution between the simulation phase and the stage where the students can develop their own robots. This approach will allow the students to keep working in robotic areas such as: cooperative behaviour, perception, navigation and data fusion. The propose approach proved to be a motivation step not only for the students but also for the teachers. Students and teachers were able to reach an agreement between the level of demand imposed by the teachers and satisfaction/motivation of the students.

Calibration Method for Underwater Visual Ground-Truth System

This work presents an automatic calibration method for a vision based external underwater ground-truth positioning system. These systems are a relevant tool in benchmarking and assessing the quality of research in underwater robotics applications. A stereo vision system can in suitable environments such as test tanks or in clear water conditions provide accurate position with low cost and flexible operation. In this work we present a two step extrinsic camera parameter calibration procedure in order to reduce the setup time and provide accurate results. The proposed method uses a planar homography decomposition in order to determine the relative camera poses and the determination of vanishing points of detected lines in the image to obtain the global pose of the stereo rig in the reference frame. This method was applied to our external vision based ground-truth at the INESC TEC/Robotics test tank. Results are presented in comparison with an precise calibration performed using points obtained from an accurate 3D LIDAR modelling of the environment.

Reproduction of Leishmania (Leishmania ) infantum chagasi in conditioned cell culture growth medium

Leishmanias can be produced by inoculation in conditioned McCoy cell culture growth medium (CGM). Leishmania (Leishmania) infantum chagasi (100 parasites) grown in NNN medium was inoculated in 2.5 mL CGM, kept in plates (24 wells) and its multiplication was observed for five days (120 hours). After day 5, the medium was saturated with the flagellate forms of the parasite (promastigotes). The reproduction of the leishmanias was observed every 24 hours and the number of parasites was calculated by counting the parasites in a drop of 10 µ L and photomicrographied. So the number of Leishmanias was adjusted to 1 mL volume. The advantage of the technique by isolation of Leishmania in CGM demonstrated in this study is its low cost and high efficacy even with a small quantity of parasites (10² promastigotes) used as inoculum. Additionally, isolation of the leishmania can be obtained together with an increase in their density (180 times) as observed by growth kinetics, within a shorter time. These results justify the use of this low-cost technique for the isolation and investigation of the behavior and multiplication of Leishmania both in vertebrates and invertebrates, besides offering means of obtaining antigens, whether whole antigens (leishmanias) or the soluble antigens produced by the parasites which may be useful for the production of new diagnostic kits.

Aplicação de Internet of Things em casas inteligentes: Serviços de Rede

O foco principal no estudo da Internet of Things tem sido a integração de dispositivos digitais com o mundo físico e vice-versa. Os dispositivos inteligentes têm vindo a ganhar uma forte presença na nossa vida diária e cada vez mais, tendem a integrar o sistema de uma casa, automatizando processos comuns como o controlo de temperatura ambiente ou mesmo a percentagem de luminosidade de uma divisão. A visão da IoT contempla um mundo interconectado, recolhendo informações de forma automática e possibilitando a comunicação entre dispositivos. Contudo, as tecnologias existentes para a criação de redes que albergam estes novos dispositivos carecem de padrões bem definidos, dificultando a interoperabilidade entre as diversas soluções existentes. Neste projeto são estudadas e aplicadas as tecnologias mais promissoras aplicáveis ao paradigma Internet of Things, com o objetivo de encontrar um conjunto de protocolos padrão para a implementação de sistemas de automação em casas inteligentes.1 Como objetivo final deste projeto, pretende-se criar uma rede de dispositivos com capacidades sensoriais que tenham a capacidade de comunicar com o mundo externo, permitindo o acesso à rede por qualquer tipo de utilizador. Com isso, espera-se caminhar para mais perto da padronização dos protocolos inerentes à IoT e habilitar interoperabilidade entre as mais diversas soluções. São apresentados e utilizados os protocolos que mais se adaptam ao tema escolhido, tentando simplificar a rede para que esta possa ser incluída em qualquer ambiente doméstico, recorrendo a hardware de custo reduzido. Os protocolos apresentados são o 6LoWPAN, utilizando o protocolo IEEE 802.15.4 como interface de rede juntamente com endereçamento IPv6. É também utilizado o protocolo CoAP na troca de mensagens entre os dispositivos.

Simulação de Robôs Quadrúpedes Utilizando o SimMechanics

Desde sempre o Homem procurou automatizar tarefas repetitivas. Tanto na indústria como no sector doméstico ou de comércio estão constantemente a surgir novos equipamentos procurando aumentar o nível de automação de diversas tarefas. A necessidade de empresas criadoras de produtos inovadores se manterem concorrenciais obrigou à adopção de métodos de projecto e planeamento mais estruturados e eficientes que eliminem os desperdícios tanto de material como de tempo. Diversas construções em termos orçamentais e o aumento da procura de produtos de alta qualidade a baixo custo deu origem a um novo tipo de programas, os programas de simulação virtual. Tal como na indústria, também na investigação nas Instituições de Ensino Superior se procuram adoptar os métodos de trabalho mais eficientes possíveis. Uma parte dos programas de simulação robótica utilizados hoje em dia na investigação no Instituto Superior de Engenharia do Porto estão concebidos em linguagem C. Embora esta linguagem seja extremamente capaz, existem métodos mais adequados de simulação que aceleram o processo de modelação permitindo a visualização do movimento e simulação de diversas situações potencialmente criticas sem existir a necessidade de construção de um protótipo funcional do robô. Durante o último ano, este projecto permitiu construir um modelo de um robô quadrúpede num programa de simulação virtual chamado Simmechanics™. Embora haja já algum trabalho desenvolvido nesta área, constatou-se que a informação existente possuía algumas lacunas. Com o trabalho desenvolvido preparou-se esta dissertação que pretende clarificar algumas questões que surgem na modelação de um robô. Neste documento explica-se como modelar um robô de corpo flexível, modelar as pernas e as respectivas juntas da anca e do joelho assim como também se apresenta a modelação de um contacto com o solo recorrendo a um modelo descrito na literatura. Este documento foi escrito a pensar no leitor, procurando-se explicar de forma simples mas concisa os diversos passos necessários para construir um modelo virtual de um robô. O autor espera, desta forma, ajudar futuros colegas que pretendam trabalhar com o Simmechanics™ a mais facilmente se integrarem com o programa aumentando desta forma o declive da curva de aprendizagem e permitindo um maior aproveitamento desta ferramenta.

A potentiometric magnetic immunoassay for rapid detection of Salmonella typhimurium

Potentiometric detection with homemade polymeric membrane microelectrodes was coupled to a magnetic sandwich immunoassay for Salmonella typhimurium determination. Cadmium and sodium ion selective electrodes were used respectively as indicator and pseudo-reference electrodes and were prepared in pipette tips to allow potentiometric measurements in microliter sample volumes. In the proposed method, the concentration of S. typhimurium was proportional to the amount of cadmium released upon dissolution of a CdS nanoparticle labeled to the secondary detection antibody. The limit of detection was 2 cells per 100 μL. The immunomagnetic assay with potentiometric detection is suitable for sensitive and rapid (average total time per assay of 75 minutes) detection of S. typhimurium in milk samples. The proposed method is easy to perform, safe, sensitive, and low cost and has potential for in situ analysis.

Water jet based autonomous surface vehicle for coastal waters operations

This paper presents the design of low cost, small autonomous surface vehicle for missions in the coastal waters and specifically for the challenging surf zone. The main objective of the vehicle design described in this paper is to address both the capability of operation at sea in relative challenging conditions and maintain a very low set of operational requirements (ease of deployment). This vehicle provides a first step towards being able to perform general purpose missions (such as data gathering or patrolling) and to at least in a relatively short distances to be able to be used in rescue operations (with very low handling requirements) such as carrying support to humans on the water. The USV is based on a commercially available fiber glass hull, it uses a directional waterjet powered by an electrical brushless motor for propulsion, thus without any protruding propeller reducing danger in rescue operations. Its small dimensions (1.5 m length) and weight allow versatility and ease of deployment. The vehicle design is described in this paper both from a hardware and software point of view. A characterization of the vehicle in terms of energy consumption and performance is provided both from test tank and operational scenario tests. An example application in search and rescue is also presented and discussed with the integration of this vehicle in the European ICARUS (7th framework) research project addressing the development and integration of robotic tools for large scale search and rescue operations.