Effect of Airborne-Particle Abrasion and Mechanico-Thermal Cycling on the Flexural Strength of Glass Ceramic Fused to Gold or Cobalt-Chromium Alloy

Purpose: To evaluate the effect of airborne-particle abrasion and mechanico-thermal cycling on the flexural strength of a ceramic fused to cobalt-chromium alloy or gold alloy.Materials and Methods: Metallic bars (n = 120) were made (25 mm x 3 mm x 0.5 mm): 60 with gold alloy and 60 with Co-Cr. At the central area of the bars (8 mm x 3 mm), a layer of opaque ceramic and then two layers of glass ceramic (Vita VM13, Vita Zahnfabrick) were fired onto it (thickness: 1 mm). Ten specimens from each alloy group were randomly allocated to a surface treatment [(tungsten bur or air-particle abrasion (APA) with Al(2)O(3) at 10 mm or 20 mm away)] and mechanico-thermal cycling (no cycling or mechanically loaded 20,000 cycles; 10 N distilled water at 37 degrees C and then thermocycled 3000 cycles; 5 degrees C to 55 degrees C, dwell time 30 seconds) combination. Those specimens that did not undergo mechanico-thermal cyclingwere stored inwater (37 degrees C) for 24 hours. Bond strength was measured using a three-point bend test, according to ISO 9693. After the flexural strength test, failure types were noted. The data were analyzed using three factor-ANOVA and Tukey's test (alpha = 0.05).Results: There were no significant differences between the flexural bond strength of gold and Co-Cr groups (42.64 +/- 8.25 and 43.39 +/- 10.89 MPa, respectively). APA 10 and 20 mm away surface treatment (45.86 +/- 9.31 and 46.38 +/- 8.89 MPa, respectively) had similar mean flexural strength values, and both had significantly higher bond strength than tungsten bur treatment (36.81 +/- 7.60 MPa). Mechanico-thermal cycling decreased the mean flexural strength values significantly for all six alloy-surface treatment combinations tested when compared to the control groups. The failure type was adhesive in the metal/ceramic interface for specimens surface treated only with the tungsten bur, and mixed for specimens surface treated with APA 10 and 20 mm.Conclusions: Considering the levels adopted in this study, the alloy did not affect the bond strength; APA with Al(2)O(3) at 10 and 20 mm improved the flexural bond strength between ceramics and alloys used, and the mechanico-thermal cycling of metal-ceramic specimens resulted in a decrease of bond strength.

Flexural Strength of Four Adhesive Fixed Dental Prostheses of Composite Resin Reinforced with Glass Fiber

Purpose: To evaluate the flexural strength of two fixed dental prosthesis (FDP) designs simulating frameworks of adhesive fixed partial prostheses, reinforced or not by glass fiber.Materials and Methods: Forty specimens, made with composite resin, were divided into 4 groups according to the framework design and the presence of fiber reinforcement: A1 - occlusal support; A2: occlusal support + glass fiber; B1: occlusal and proximal supports; B2: occlusal and proximal supports + glass fiber. The specimens were subjected to the three-point bending test, and the data were submitted to two-way ANOVA and Tukey's test (5%).Results: Group A2 (97.9 +/- 38 N) was statistically significantly different from all other experimental groups, presenting a significantly lower mean flexural strength.Conclusion: The use of glass fibers did not improve the flexural strength of composite resin, and designs with occlusal and proximal supports presented better results than designs simulating only occlusal support.

Flexural Strength of Glass-Infiltrated Zirconia/Alumina-Based Ceramics and Feldspathic Veneering Porcelains

Purpose: To compare the flexural strength of two glass-infiltrated high-strength ceramics and two veneering glass-ceramics.Materials and Methods: Four ceramic materials were tested: two glass-infiltrated high-strength ceramics used as framework in metal-free restorations [In-Ceram Zirconia IZ (Gr1) and In-Ceram Alumina IA (Gr2)], and two glass-ceramics used as veneering material in metal-free restorations [Vita VM7 (Gr3) and Vitadur-alpha (Gr4)]. Bar specimens (25 x 5 x 2 mm(3)) made from core ceramics, alumina, and zirconia/alumina composites were prepared and applied to a silicone mold, which rested on a base from a gypsum die material. The IZ and IA specimens were partially sintered in an In-Ceram furnace according to the firing cycle of each material, and then were infiltrated with a low-viscosity glass to yield bar specimens of high density and strength. The Vita VM7 and Vitadur-alpha specimens were made from veneering materials, by vibration of slurry porcelain powder and condensation into a two-part brass Teflon matrix (25 x 5 x 2 mm(3)). Excess water was removed with absorbent paper. The veneering ceramic specimens were then removed from the matrix and were fired as recommended by the manufacturer. Another ceramic application and sintering were performed to compensate the contraction of the feldspar ceramic. The bar specimens were then tested in a three-point bending test.Results: The core materials (Gr1: 436.1 +/- 54.8; Gr2: 419.4 +/- 83.8) presented significantly higher flexural strength (MPa) than the veneer ceramics (Gr3: 63.5 +/- 9.9; Gr4: 57.8 +/- 12.7).Conclusion: In-Ceram Alumina and Zirconia were similar statistically and more resistant than VM7 and Vitadur-alpha.

Opaque Layer Firing Temperature and Aging Effect on the Flexural Strength of Ceramic Fused to Cobalt-Chromium Alloy

Purpose: To evaluate the effect of the opaque layer firing temperature and mechanical and thermal cycling on the flexural strength of a ceramic fused to commercial cobalt-chromium alloy (Co-Cr). The hypotheses were that higher opaque layer temperatures increase the metal/ceramic bond strength and that aging reduces the bond strength.Materials and Methods: Metallic frameworks (25 x 3 x 0.5 mm(3); ISO 9693) (N = 60) were cast in Co-Cr and airborne-particle abraded (Al(2)O(3): 150 mu m) at the central area of the frameworks (8 x 3 mm(2)) and divided into three groups (N = 20), according to the opaque layer firing temperature: Gr1 (control)-900 degrees C; Gr2-950 degrees C; Gr3-1000 degrees C. The opaque ceramic (Opaque, Vita Zahnfabrick, Bad Sackingen, Germany) was applied, and the glass ceramic (Vita Omega 900, Vita Zahnfabrick) was fired onto it (thickness: 1 mm). While half the specimens from each group were randomly tested without aging (water storage: 37 degrees C/24 hours), the other half were mechanically loaded (20,000 cycles; 50 N load; distilled water at 37 degrees C) and thermocycled (3000 cycles; 5 degrees C to 55 degrees C, dwell time: 30 seconds). After the flexural strength test, failure types were noted. The data were analyzed using 2-way ANOVA and Tukey's test (alpha = 0.05).Results: Gr2 (19.41 +/- 5.5 N) and Gr3 (20.6 +/- 5 N) presented higher values than Gr1 (13.3 +/- 1.6 N) (p = 0.001). Mechanical and thermal cycling did not significantly influence the mean flexural strength values (p > 0.05). Increasing the opaque layer firing temperature improved the flexural bond strength values (p < 0.05). The hypotheses were partially accepted.Conclusion: Increasing of the opaque layer firing temperature improved the flexural bond strength between ceramic fused to Co-Cr alloy.

Mechanical and thermal cycling effects on the flexural strength of glass ceramics fused to titanium

This study evaluated the effects of mechanical and thermal cycling on the flexural strength (ISO 9693) of three brands of ceramics fused to commercially pure titanium (cpTi). Metallic frameworks of 25 x 3 x 0.5 mm dimensions (N = 84) were cast in cpTi, followed by 150-mu m aluminum oxide airborne particle abrasion at a designated area of the frameworks (8 x 3 mm). Bonder and opaque ceramic were applied on the frameworks, and then the corresponding ceramic (Triceram, Super Porcelain Ti-22, Vita Titankeramik) was fired onto them (thickness: 1 mm). Half of the specimens from each ceramic-metal combination were randomly tested without aging (only water storage at 37 degrees C for 24 hours), while the other half were mechanically loaded (20,000 cycles under 10 N load, immersion in distilled water at 37 degrees C) and thermocycled (3,000 cycles, between 5-55 degrees C, dwell time of 13 seconds). After the flexural strength test, failure types were noted. Mechanical and thermal cycling decreased the mean flexural strength values significantly (p<0.05) for all the three ceramic-cpTi combinations tested when compared to the control group. In all the three groups, failure type was exclusively adhesive at the opaque ceramic-cpTi interfacial zone with no presence of ceramic on the substrate surface except for a visible oxide layer.

Amino acid, Antioxidant and Ion Profiles of Carpolobia lutea Leaf (Polygalaceae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Anatomical characterization and chemical profile of Laguncularia racemosa (L.) Gaertn leaf blades, from impacted and non-impacted mangroves of the São Paulo Coast

Anatomical characterization and chemical profile of Laguncularia racemosa (L.) Gaertn leaf blades, from impacted and non-impacted mangroves of the São Paulo Coast. Several sources of environmental impact have caused great damage to the flora in mangroves. Therefore, this study aimed to analyze the anatomy and chemical composition of Laguncularia racemosa (L.) Gaertn leaf blades, from impacted (Municipality of Santos) and non-impacted mangroves (Municipality of Peruibe) of the São Paulo Coast. For the leaf anatomy studies, light microscopy and scanning electron microscopy (SEM) were used. For chemical analysis, high performance liquid chromatography (HPLC) was conducted. The biometry revealed leaf tissues of plants from impacted mangroves with a less thick epidermis and mesophyll and higher width of the central vascular beam. A smaller number of stomata and higher amounts of daises in these leaves were also observed. Results were confirmed by the Student t-test (alpha = 5%). The chemical profiles revealed a higher ammount of secondary metabolites in leaves from the impacted environment.

Leaf Structure and Taxonomy of Petunia and Calibrachoa (Solanaceae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Leaf heliotropism in Styrax camporum Pohl from the Brazilian cerrado: distinct gas exchange and leaf structure, but similar leaf temperature and water relations

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise de crescimento de duas cultivares de feijoeiro sob irrigação, em plantio direto e preparo convencional

O objetivo deste trabalho foi avaliar, através da análise de crescimento, os efeitos do plantio direto (PD) e do preparo convencional (PC) sobre o desenvolvimento de duas cultivares de feijoeiro (Phaseolus vulgaris L.), em dois espaçamentos diferentes, irrigadas via pivô central. O experimento foi conduzido no ano de 1994, em Senador Canedo, GO, a 16º 41' de latitude Sul, 49º 16' de longitude Oeste e 741 m de altitude. O delineamento experimental foi inteiramente casualizado em parcelas subsubdivididas, com oito tratamentos. Para avaliação da área foliar e da produção de matéria seca total (MST), foram feitas dez coletas periódicas a cada sete dias, com três plantas ao acaso e duas repetições. A análise de crescimento evidenciou que no sistema PD o feijoeiro aumentou a MST, o índice de área foliar, a taxa de crescimento da cultura, a taxa de crescimento relativo, a taxa assimilatória líquida e a duração da área foliar, ocorrendo diminuição da razão de área foliar. A cultivar Aporé destacou-se em relação à Safira, sem efeito para espaçamento. A análise de crescimento apresentou-se adequada para avaliar o desenvolvimento do feijoeiro.

Attractiveness of copperleaf-based bait to leaf-cutting ants

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Droplet deposition during spray and leaf pH in aquatic weed control

A diversidade morfológica da superfície foliar existente entre as espécies de plantas e a presença de estruturas foliares como tricomas, estômatos, cutícula e ceras podem exercer grande influência na aderência e deposição das gotas de pulverização, assim como na absorção do herbicida. Desta forma, o objetivo do presente trabalho foi estudar, em quatro espécies de plantas daninhas aquáticas (Enhydra anagallis, Eichhornia crassipes, Heteranthera reniformis e Typha subulata), a área de molhamento de gotas de pulverização nas superfícies foliares adaxial e abaxial, bem como o pH foliar. O experimento foi realizado em Botucatu-SP. As plantas foram cultivadas em caixas d'água sob condições de campo, e quando atingiram seu pleno desenvolvimento (antes do florescimento), foram realizadas as avaliações de pH foliar e da área de molhamento de gotas de pulverização. As tensões superficiais das gotas aplicadas (0,5 mL), apresentadas pelas soluções de glyphosate aplicado isolado a 5,0% v v-1 (Rodeo 480 g L-1 e.a. produto comercial), glyphosate + Aterbane BR (5,0% + 0,5% v v-1), glyphosate + Silwet L-77 (5,0% + 0,05% v v-1), além das soluções com os adjuvantes isolados, Aterbane BR (0,5% v v-1) e Silwet L-77 (0,05% v v-1) foram respectivamente 72,1; 28,7; 23,3; 37,3 e 22,1 mN m-1. As médias obtidas de pH foliar variaram entre 5,50 e 7,50, destacando-se a espécie E. anagallis com valores de 6,68 e 7,02 para as faces adaxial e abaxial, respectivamente. Dentre as plantas daninhas aquáticas avaliadas T. subulata foi a espécie que apresentou as maiores médias de área de molhamento nas faces adaxial e abaxial da folha, proporcionada pelas as soluções de glyphosate + Aterbane BR, glyphosate + Silwet L-77 e Silwet L-77, com valores de 12,99-7,03; 20,04-17,95 e 31,81-25,91 mm², respectivamente.

Shade level effects on yield and chemical composition of the leaf essential oil of Pothomorphe umbellata (L.) Miquel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)