Effect of Microtopography, Slope Length and Gradient, and Vegetative Cover on Overland Flow Through Simulation

Overland flow on a hillslope is significantly influenced by its microtopography, slope length and gradient, and vegetative cover. A 1D kinematic wave model in conjunction with a revised form of the Green-Ampt infiltration equation was employed to evaluate the effect of these surface conditions. The effect of these conditions was treated through the resistance parameter in the kinematic wave model. The resistance in this paper was considered to be made up of grain resistance, form resistance, and wave resistance. It was found that irregular slopes with microtopography eroded more easily than did regular slopes. The effect of the slope gradient on flow velocity and flow shear stress could be negative or positive. With increasing slope gradient, the flow velocity and shear stress first increased to a peak value, then decreased again, suggesting that there exists a critical slope gradient for flow velocity and shear stress. The vegetative cover was found to protect soil from erosion primarily by enhancing erosion-resisting capacity rather than by decreasing the eroding capability of overland flow.

Análisis económico de tres fincas de producción bovina de doble propósito explotadas de forma intensiva y extensiva durante el período 1992-1993

El objetivo principal del estudio fue conocer el comportamiento económico de tres fincas ganaderas de Doble Propósito; dos de ellas, ubicadas en el municipio de "Muy Muy" y explotadas de forma extensiva (fincas 1 y 2) y una tercera en el municipio de Tipitapa explotada de forma intensiva (3). La. base principal de este trabajo la constituyó la información proporcionada por loa productores, la que fue recolectada a través de un diagnóstico estático y un dinámico por el periodo de un año, la mayor parte de esta era de carácter económico, dándole prioridad a los gastos e ingresos incurridos en el periodo, además, se consideró algunas actividades de manejo practicado en ella. Se determinaron algunos índices productivos, la inversión inicial en medios fijos, los gastos por componentes, los ingresos y la rentabilidad entre otras. Los resultados indican que las fincas ubicadas en la zona de Tipitapa presentan ventajas comparativas en cuanto a la calidad de los suelos, facilidad de tecnificación, acceso al mercado, adquisición de insumos a más bajos precios Etc., dentro de las fincas evaluadas la tierra represento la mayor inversión de capital en medios fijos (53.58%), para las fincas de "Muy Muy" y 38% para la finca tres. Los mayores gastos correspondieron al componente mano de obra en las tres fincas, mientras que lo efectuado en alimentación en la finca uno y dos (10%) reflejan la baja suplementación en relación a la finca tres (40%) el que constituyó en esta un gasto constante. Respecto a los costos fijos y variables, la finca uno fue la que presentó los costos fijos más altos (76.29%); y la finca tres los costos variables (39.50%). El costo de producción de un litro de leche resultó superior al precio de venta del mismo en las tres fincas, al considerar dentro de los costos el interés de capital (Método A), el precio de venta fue C$1.25, C$1.15 y C$1,50 y el costo de producción de C$1.44, C$1.16 y C$1. 72. Al excluir dicho interés (Método B) el costo de producción fue de C$1.09, C$0.86 y C$1.42. Los mayores ingresos fueron aportados por el subsistema leche en las tres fincas, por concepto de venta de leche fluida y animales propios de esta actividad (85.40%, 98.12% y 67.24%). Al establecer relación entre los ingresos totales, costos totales y la inversión se encontró que las fincas 1 y 3 operaron con pérdidas determinándose entonces que las actividades no fueron rentables (-7.283%) y (-12.663%) durante este período, mientras que la finca 2 presentó una rentabilidad de (4.4%). Se identificaron algunas limitantes que al final repercuten en la actividad económica de las fincas sobresaliendo entre otros: Los bajos precios por la venta de los productos, los altos costos de los insumos, falta de conservación de pastos en la época seca, asistencia técnica irregular, la no utilización de registros, entre otras. Sólo con el incremento del volumen de la producción y superando la mayoría de las limitantes es que se logrará que las fincas amplíen sus beneficios, cubran sus costos y logren operar sin pérdidas.

Efecto de la dosis y el momento de aplicación del nitrógeno sobre la producción y calidad de semilla de pasto gamba (Andropogon gayanus Kunth)

El presente trabajo tuvo como objetivo, evaluar en términos biológicos y económicos, el efecto de la dosis y el momento de aplicación de nitrógeno, sobre la producción y calidad de semillas de Androppgon gayanus CIAT 621. El estudio se llevó a cabo en la finca "Santa Rosa", ubicada al Oeste de la ciudad de Managua. El análisis de calidad de semilla se realizó empleándose la metodología utilizada por el CIAT, para el análisis de calidad de semillas brozosas. Se utilizó un diseño de bloques completos al azar, para un arreglo bifactorial de cuatro dosis y tres momentos de aplicación de nitrógeno. Se incluyó un tratamiento testigo, sin fertilización, para un total de 13 tratamientos y tres repeticiones por tratamiento. Los resultados evidencian que las dosis de nitrógeno y los momentos de aplicación, tuvieron efecto estadísticamente significativo (P<0.01) sobre el Número de Tallos Reproductivos Totales por Hectárea y el rendimiento de semilla Cruda por Hectárea. El incremento en el rendimiento de Semilla Cruda por Hectárea, estuvo asociado con el incremento del Número de Tallos Reproductivos Totales por Hectárea (r=.82) (P0.05), respecto de la dosis de 75 kg N/ha, aplicados a los 20 días después del corte de uniformidad (55.31%). Para el porcentaje de Germinación, el valor más alto resultó cuando se aplicaron 100 kg N/ha, a los 40 días después del corte de uniformidad (46%), presentando diferencias no significativas (P>0.05), con la dosis de 25 kg N/ha, aplicados a los 40 días después del corte de uniformidad (45%). El Valor Cultural presentó una tendencia similar a las dos variables anteriores, (Semilla Pura y Germinación).Este resultado se debió a que el Valor Cultural es un índice compuesto producto de ambas variables. Su mayor valor se obtuvo con la dosis de 25 kg N/ha, aplicados a los 40 días después del corte de uniformidad (25%), siendo estadísticamente igual (P>0.05), cuando se aplicaron 75 kg N/ha, 20 días después del corte de uniformidad (23.78%).Este comportamiento irregular, en el efecto del nitrógeno sobre los parámetros de calidad de la semilla (Semilla Pura, Germinación y Valor Cultural), coincide con lo reportado por Ferguson (1991), quien afirma que los efectos del nitrógeno en la calidad de la semilla son variables, pero normalmente no tiene efecto. Otros autores; Cameron y Mullaly (1969) y Grof (1969), citados por Humphreys (1975}, reportan que no encontraron una relación consistente entre la calidad de la semilla y el nivel de nitrógeno, en la producción de semilla de pastos tropicales. De todos los tratamientos evaluados, el mayor beneficio monetario se obtuvo con la dosis de 75 kg N/ha aplicados a los 40 días después del corte de uniformidad (US $ 1,111.10/ha). No obstante, la dosis de 25 kg N/ha aplicados a los 40 días después del corte de uniformidad fue el tratamiento con el que se obtuvo el mayor margen de ingreso bruto (96.5% del ingreso total), en comparación con el resto de tratamientos en que se aplicó nitrógeno.

Experimental and micromechanical study of size effects in the constrained deformation of metallic foams

Previous investigations have unveiled size effects in the strength of metallic foams under simple shear - the shear strength increases with diminishing specimen size, a phenomena similar to that shown by Fleck et al. (Acta Mat., 1994, Vol. 42, p. 475.) on the torsion tests of copper wires of various radii. In this study, experimental study of the constrained deformation of a foam layer sandwiched between two steel plates has been conducted. The sandwiched plates are subjected to combined shear and normal loading. It is found that measured yield loci of metallic foams in the normal and shear stress space corresponding to various foam layer thicknesses are self-similar in shape but their size increases as the foam layer thickness decreases. Moreover, the strains profiles across the foam layer thickness are parabolic instead of uniform; their values increase from the interfaces between the foam layer and the steel plates and reach their maximum in the middle of the foam layer, yielding boundary layers adjacent to the steel plates. In order to further explore the origin of observed size effects, micromechanics models have been developed, with the foam layer represented by regular and irregular honeycombs. Though the regular honeycomb model is seen to underestimate the size effects, the irregular honeycomb model faithfully captures the observed features of the constrained deformation of metallic foams.

Size effects in the constrained deformation of metallic foams

The constrained deformation of an aluminium alloy foam sandwiched between steel substrates has been investigated. The sandwich plates are subjected to through-thickness shear and normal loading, and it is found that the face sheets constrain the foam against plastic deformation and result in a size effect: the yield strength increases with diminishing thickness of foam layer. The strain distribution across the foam core has been measured by a visual strain mapping technique, and a boundary layer of reduced straining was observed adjacent to the face sheets. The deformation response of the aluminium foam layer was modelled by the elastic-plastic finite element analysis of regular and irregular two dimensional honeycombs, bonded to rigid face sheets; in the simulations, the rotation of the boundary nodes of the cell-wall beam elements was set to zero to simulate full constraint from the rigid face sheets. It is found that the regular honeycomb under-estimates the size effect whereas the irregular honeycomb provides a faithful representation of both the observed size effect and the observed strain profile through the foam layer. Additionally, a compressible version of the Fleck-Hutchinson strain gradient theory was used to predict the size effect; by identifying the cell edge length as the relevant microstructural length scale the strain gradient model is able to reproduce the observed strain profiles across the layer and the thickness dependence of strength. © 2002 Elsevier Science Ltd. All rights reserved.

Two-Dimensional Kinematic Wave Model of Overland-Flow

A two-dimensional kinematic wave model was developed for simulating runoff generation and flow concentration on an experimental infiltrating hillslope receiving artificial rainfall. Experimental observations on runoff generation and flow concentration on irregular hillslopes showed that the topography of the slope surface controlled the direction and flow lines of overland flow. The model-simulated results satisfactorily compared with experimental observations. The erosive ability of the concentrated flow was found to mainly depend on the ratio of the width and depth of confluent grooves.

A time domain computation method for dynamic behavior of mooring system

A quasi-steady time domain method is developed for the prediction of dynamic behavior of a mooring system under the environmental disturbances, such as regular or irregular waves, winds and currents. The mooring forces are obtained in a static sense at each instant. The dynamic feature of the mooring cables can be obtained by incorporating the extended 3-D lumped-mass method with the known ship motion history. Some nonlinear effects, such as the influence of the instantaneous change of the wetted hull surface on the hydrostatic restoring forces and Froude-Krylov forces, are included. The computational results show a satisfactory agreement with the experimental ones.

Attractor crisis and bursting in a fluid flow with two no-slip directions

Characteristic burtsing behavior is observed in a driven, two-dimensional viscous flow, confined to a square domain and subject to no-slip boundaries. Passing a critical parameter value, an existing chaotic attractor undergoes a crisis, after which the flow initially enters a transient bursting regime. Bursting is caused by ejections from and return to a limited subdomain of the phase space, whereas the precrisis chaotic set forms the asymptotic attractor of the flow. For increasing values of the control parameter the length of the bursting regime increases progressively. Passing another critical parameter value, a second crisis leads to the appearance of a secondary type of bursting, of very large dynamical range. Within the bursting regime the flow then switches in irregular intervals from the primary to the secondary type of bursting. Peak enstrophy levels for both types of bursting are associated to the collapse of a primary vortex into a quadrupolar state.

The annular crack in a nonhomogeneous matrix surrounding a fiber under torsional loading .2. The crack going through the bimaterial interface into the fiber

The axisymmetric problem of an elastic fiber perfectly bonded to a nonhomogeneous elastic matrix which contains an annular crack going through the interface into the fiber under axially symmetric shear stress is considered. The nature of the stress singularity is studied. It is shown that at the irregular point on the interface, whether the shear modulus is continuous or discontinuous the stresses are bounded. The problem is formulated in terms of a singular integral equation and can be solved by a regular method. The stress intensity factors and crack surface displacement are given.

Some theorems in asymptotic analysis

Basing ourselves on the analysis of magnitude of order, we strictly prove fundamental lemmas for asymptotic integral, including the cases of infinite region. Then a general formula for asymptotic expansion of integrals is given. Finally, we derive a sufficient condition for an ordinary differential equation to possess a solution of the Frobenius series type at finite irregular singularities or branching points.

Características psicoinstruccionales de alumnado preadolescente y rendimiento académico en la Educación Artística escolar

Este trabajo investiga la relación de determinadas características del alumnado de Educación Primaria y de Secundaria (teorías implícitas de la inteligencia, metas académicas de logro, autoconcepto social, compromiso con las tareas artísticas y actitudes hacia la enseñanza artística en la escuela) con el rendimiento académico (calificación y comprensión artística) en la asignatura de Educación Artística. Se formulan cuatro hipótesis que plantean relación débil de las calificaciones académicas en la asignatura de Artes Visuales con el nivel de comprensión, así como relación positiva y significativa del rendimiento académico en Educación Artística con concepciones sobre la propia inteligencia como incremental, con el compromiso con las tareas artísticas, con las actitudes hacia la asignatura, con las metas de aprendizaje y con el autoconcepto social. Los resultados, obtenidos de una muestra de 606 escolares de Educación Primaria y Secundaria, confirman parcialmente las hipótesis de investigación pues se constata cierta relación significativa, positiva e irregular entre calificación en Educación Artística y comprensión artística, se confirma la relación previamente hipotetizada del compromiso con las tareas artísticas y de las actitudes hacia la Educación Artística con el rendimiento académico en la asignatura de Arte, y se señala asimismo relación estadísticamente significativa de las metas académicas de aprendizaje y del autoconcepto social con la calificación y con la comprensión artísticas, si bien las metas de desempeño también muestran ciertas relaciones significativas con el rendimiento artístico. Se concluye subrayando la relevancia del presente trabajo al establecer relaciones significativas entre características del alumnado y su rendimiento académico en la asignatura de Educación Plástica y Visual.

[A_Laguardia_SanJuan] Levantamiento fotogramétrico de la portada Sur o “de los abuelos” de la iglesia de San Juan de Laguardia (Álava)

[ES] La documentación contenida en este registro ha servido de base para los siguientes documentos:

3D Finite Volume Scheme for Czochralski Single Crystal Growth

Czochralski (Cz) technique, which is used for growing single crystals, has dominated the production of single crystals for electronic applications. The Cz growth process involves multiple phases, moving interface and three-dimensional behavior. Much has been done to study these phenomena by means of numerical methods as well as experimental observations. A three-dimensional curvilinear finite volume based algorithm has been developed to model the Cz process. A body-fitted transformation based approach is adopted in conjunction with a multizone adaptive grid generation (MAGG) technique to accurately handle the three-dimensional problems of phase-change in irregular geometries with free and moving surfaces. The multizone adaptive model is used to perform a three-dimensional simulation of the Cz growth of silicon single crystals.Since the phase change interface are irregular in shape and they move in response to the solution, accurate treatment of these interfaces is important from numerical accuracy point of view. The multizone adaptive grid generation (MAGG) is the appropriate scheme for this purpose. Another challenge encountered is the moving and periodic boundary conditions, which is essential to the numerical solution of the governing equations. Special treatments are implemented to impose the periodic boundary condition in a particular direction and to determine the internal boundary position and shape varying with the combination of ambient physicochemical transport process and interfacial dynamics. As indicated above that the applications and processes characterized by multi-phase, moving interfaces and irregular shape render the associated physical phenomena three-dimensional and unsteady. Therefore a generalized 3D model rather than a 2D simulation, in which the governing equations are solved in a general non-orthogonal coordinate system, is constructed to describe and capture the features of the growth process. All this has been implemented and validated by using it to model the low pressure Cz growth of silicon. Accuracy of this scheme is demonstrated by agreement of simulation data with available experimental data. Using the quasi-steady state approximation, it is shown that the flow and temperature fields in the melt under certain operating conditions become asymmetric and unsteady even in the absence of extrinsic sources of asymmetry. Asymmetry in the flow and temperature fields, caused by high shear initiated phenomena, affects the interface shape in the azimuthal direction thus results in the thermal stress distribution in the vicinity, which has serious implications from crystal quality point of view.

Automated, objective texture segmentation of multibeam echosounder data - Seafloor survey and substrate maps from James Island to Ozette Lake, Washington Outer Coast

Without knowledge of basic seafloor characteristics, the ability to address any number of critical marine and/or coastal management issues is diminished. For example, management and conservation of essential fish habitat (EFH), a requirement mandated by federally guided fishery management plans (FMPs), requires among other things a description of habitats for federally managed species. Although the list of attributes important to habitat are numerous, the ability to efficiently and effectively describe many, and especially at the scales required, does not exist with the tools currently available. However, several characteristics of seafloor morphology are readily obtainable at multiple scales and can serve as useful descriptors of habitat. Recent advancements in acoustic technology, such as multibeam echosounding (MBES), can provide remote indication of surficial sediment properties such as texture, hardness, or roughness, and further permit highly detailed renderings of seafloor morphology. With acoustic-based surveys providing a relatively efficient method for data acquisition, there exists a need for efficient and reproducible automated segmentation routines to process the data. Using MBES data collected by the Olympic Coast National Marine Sanctuary (OCNMS), and through a contracted seafloor survey, we expanded on the techniques of Cutter et al. (2003) to describe an objective repeatable process that uses parameterized local Fourier histogram (LFH) texture features to automate segmentation of surficial sediments from acoustic imagery using a maximum likelihood decision rule. Sonar signatures and classification performance were evaluated using video imagery obtained from a towed camera sled. Segmented raster images were converted to polygon features and attributed using a hierarchical deep-water marine benthic classification scheme (Greene et al. 1999) for use in a geographical information system (GIS). (PDF contains 41 pages.)

Survey report of NOAA Ship McArthur II cruises AR-04-04, AR-05-05 and AR-06-03: Habitat classification of side scan sonar imagery in support of deep-sea coral/sponge explorations at the Olympic Coast National Marine Sanctuary

Habitat mapping and characterization has been defined as a high-priority management issue for the Olympic Coast National Marine Sanctuary (OCNMS), especially for poorly known deep-sea habitats that may be sensitive to anthropogenic disturbance. As a result, a team of scientists from OCNMS, National Centers for Coastal Ocean Science (NCCOS), and other partnering institutions initiated a series of surveys to assess the distribution of deep-sea coral/sponge assemblages within the sanctuary and to look for evidence of potential anthropogenic impacts in these critical habitats. Initial results indicated that remotely delineating areas of hard bottom substrate through acoustic sensing could be a useful tool to increase the efficiency and success of subsequent ROV-based surveys of the associated deep-sea fauna. Accordingly, side scan sonar surveys were conducted in May 2004, June 2005, and April 2006 aboard the NOAA Ship McArthur II to: (1) obtain additional imagery of the seafloor for broader habitat-mapping coverage of sanctuary waters, and (2) help delineate suitable deep-sea coral/sponge habitat, in areas of both high and low commercial-fishing activities, to serve as sites for surveying-in more detail using an ROV on subsequent cruises. Several regions of the sea floor throughout the OCNMS were surveyed and mosaicked at 1-meter pixel resolution. Imagery from the side scan sonar mapping efforts was integrated with other complementary data from a towed camera sled, ROVs, sedimentary samples, and bathymetry records to describe geological and biological (where possible) aspects of habitat. Using a hierarchical deep-water marine benthic classification scheme (Greene et al. 1999), we created a preliminary map of various habitat polygon features for use in a geographical information system (GIS). This report provides a description of the mapping and groundtruthing efforts as well as results of the image classification procedure for each of the areas surveyed. (PDF contains 60 pages.)