Desempenho de argamassas produzidas com agregados reciclados oriundos do resíduo de construção e demolição da Grande Natal-RN

The construction industry is responsible for generating a lot of waste because of their activities. Consequently, it is noticeable the occurrence of environmental problems in terms of its disposal in inappropriate places. Faced with this problem, some studies have been conducted with the aim of developing technologies and alternatives for recycling construction and demolition waste (CDW), motivated by the scarcity of natural resources and reduction of environmental problems generated. The research aims to characterize the recycled aggregates derived from construction and demolition waste (CDW) produced in the Greater Natal-RN and analyze the performance of mortar coating produced with recycled aggregates. The study includes the chemical , physical and microstructural characterization of recycled aggregates , as well as conducting microscopic analysis and laboratory tests in the fresh state (consistency index , water retention , bulk density and content of entrained air ) and in the hardened state ( compressive strength , tensile strength in bending , water absorption by immersion and capillary , mass density and void ratio ) for mortars produced from different levels of substitution of aggregates ( 0, 20 %, 40 %, 60 %, 80 % and 100 %). The results were satisfactory, providing mortars produced with recycled aggregates, smaller mass density and dynamic modulus values as well as an increase in the rates of absorption and porosity. The tensile strength in bending and compression for TP1 (1:2:8) trait were lower for mortars produced with recycled aggregates and the best result was 20% for replacement. For the TP2 (1:8) mapping, there was an increase in resistance to traction and compression and the best result was for 100% replacement of natural aggregates by recycled. The experiments led to the conclusion that the technical and economic point of view that the mortars produced with recycled aggregates can be used in construction, only if there is an effective control in production processes of recycled aggregate and at the dosage of mortars

Cadeia produtiva da farinha de mandioca na perspectiva da análise de filière e supply chain management :um estudo de caso das relações entre a agroindústria e a distribuição

This research aims to study the manioc flour productive chain in order to understand how the relationship between its segments happens, specially between the flour agroindustry and the distribuition. This research was made from a study of case that envolved three agro industries from the Potiguar wasteland and a company of food distribution. The filiére and the supply chain management analysis were applied to identify the functioning and the organization of the manioc flour productive chain. From the study of case it s noticed that the existing contracts, even the informal ones, has mutual benefits and it suggests that they be legalized

Aplicação do método de análise hierárquica na tomada de decisão para adoção de computação em nuvem: um estudo de caso na federação das indústrias do RN

The progresses of the Internet and telecommunications have been changing the concepts of Information Technology IT, especially with regard to outsourcing services, where organizations seek cost-cutting and a better focus on the business. Along with the development of that outsourcing, a new model named Cloud Computing (CC) evolved. It proposes to migrate to the Internet both data processing and information storing. Among the key points of Cloud Computing are included cost-cutting, benefits, risks and the IT paradigms changes. Nonetheless, the adoption of that model brings forth some difficulties to decision-making, by IT managers, mainly with regard to which solutions may go to the cloud, and which service providers are more appropriate to the Organization s reality. The research has as its overall aim to apply the AHP Method (Analytic Hierarchic Process) to decision-making in Cloud Computing. There to, the utilized methodology was the exploratory kind and a study of case applied to a nationwide organization (Federation of Industries of RN). The data collection was performed through two structured questionnaires answered electronically by IT technicians, and the company s Board of Directors. The analysis of the data was carried out in a qualitative and comparative way, and we utilized the software to AHP method called Web-Hipre. The results we obtained found the importance of applying the AHP method in decision-making towards the adoption of Cloud Computing, mainly because on the occasion the research was carried out the studied company already showed interest and necessity in adopting CC, considering the internal problems with infrastructure and availability of information that the company faces nowadays. The organization sought to adopt CC, however, it had doubt regarding the cloud model and which service provider would better meet their real necessities. The application of the AHP, then, worked as a guiding tool to the choice of the best alternative, which points out the Hybrid Cloud as the ideal choice to start off in Cloud Computing. Considering the following aspects: the layer of Infrastructure as a Service IaaS (Processing and Storage) must stay partly on the Public Cloud and partly in the Private Cloud; the layer of Platform as a Service PaaS (Software Developing and Testing) had preference for the Private Cloud, and the layer of Software as a Service - SaaS (Emails/Applications) divided into emails to the Public Cloud and applications to the Private Cloud. The research also identified the important factors to hiring a Cloud Computing provider

Caracterização física do solo e desempenho operacional de máquinas agrícolas na implantação da cultura do sorgo forrageiro

Forage sorghum can be grown in areas presenting dry and hot environmental situations where the yield of other grasses can often be uneconomical. The objective of this study was to analyze the operating performance of agricultural machines in the deployment of sorghum forage in four tillage systems, as follows: no-tillage system, disk harrow + seeding, disk harrow + two light disking + seeding, minimum tillage + seeding and four seeding different speeds, as follows: 3, 5, 6 and 9 km h(-1). The study was performed under field conditions in FCA/UNESP, Botucatu County, SP, Brazil. The data were subjected to variance analysis in a simple factorial 4 x 4, and a random block design with split plots. Operational performance of the agricultural machinery, physical characteristics the soil, its water content and the yield of dry matter and green sorghum were determined. The operational performance of agricultural machines in the deployment of sorghum forage is influenced by the sowing speed and the soil tillage system used. Chisel plow was the equipment that required the highest mean traction force, mean traction and slip, as well as the lowest mean speed for the studied tillage system. Forage sorghum showed higher yields in no-tillage systems at a seeding speed of 5 km h(-1).

Efeitos do envelhecimento ambiental acelerado em compósitos poliméricos

The advantages of the use of vegetable fibers on the synthetic fibers, such as glass fibers, in the reinforcements in composites are: low cost, low density, good tenacity, good thermal properties and reduced use of instruments for their treatment or processing. However, problems related to poor performance of some mechanical natural fibers, have hindered its direct use in structural elements. In this sense, the emergence of alternative materials such as hybrids composites, involving natural and synthetic fibers, has been encouraged by seeking to improve the performance of structural composites based only on natural fibers. The differences between the physical, chemical and mechanical properties of these fibers, especially facing the adverse environmental conditions such as the presence of moisture and ultraviolet radiation, is also becoming a concern in the final response of these composites. This piece of research presents a comparative study of the strength and stiffness between two composite, both of ortoftalic polyester matrix, one reinforced with fibers of glass-E (CV) and other hybrid reinforced with natural fibers of curauá and fiberglass-E (CH). All the comparative study is based on the influence of exposure to UV rays and steam heated water in composites, simulating the aging environment. The conditions for the tests are accelerated through the use of the aging chamber. The composites will be evaluated through tests of uniaxial static mechanical traction and bending on three points. The composite of glass fiber and hybrid manufacturing industry are using the rolling manual (hand lay-up) and have been developed in the form of composites. All were designed to meet possible structural applications such as tanks and pipes. The reinforcements used in composites were in the forms of short fiber glass-E quilts (450g/m2 - 5cm) of continuous wires and fuses (whose title was of 0.9 dtex) for the curauá fibers. The results clearly show the influence of aging on the environmental mechanical performance of the composite CV and CH. The issues concerning the final characteristics of the fracture for all types of cargoes studied were also analyzed

Análise tribológica de um sistema de acionamento alternativo de pigs para a indústria do petróleo

It is analyzed through the concepts of tribology and mechanical contact and damage the suggestion of implementing a backup system for traction and passage of Pipeline Inspection Gauge (Pig) from the inside of pipelines. In order to verify the integrity of the pipelines, it is suggested the possibility of displacement of such equipment by pulling wires with steel wires. The physical and mechanical characteristics of this method were verified by accelerated tests in the laboratory in a tribological pair, wire versus a curve 90. It also considered the main mechanisms of wear of a sliding system with and without lubricant, in the absence and presence of contaminants. To try this, It was constructed a test bench able to reproduce a slip system, work on mode back-and-forth ("reciprocation"). It was used two kinds of wires, a galvanized steel and other stainless steel and the results achieved using the two kinds of steel cables were compared. For result comparative means, it was used steel cables with and without coating of Poly Vinyl Chloride (PVC). The wires and the curves of the products were characterized using metallographic analysis, microhardness Vickers tests, X-ray diffraction (XRD), X-Ray Refraction (XRF) and tensile tests. After the experiments were analyzed some parameters that have been measurable, it demonstrates to the impracticality of this proposed method, since the friction force and the concept of alternating request at the contact between the strands of wire and the inner curves that are part ducts caused severe wear. These types of wear are likely to cause possible failures in future products and cause fluid leaks

Compósito reforçado com sisal para aplicação na moda

The objective of this research is the fabrication of a composite reinforced with dyed sisal fiber and polyester matrix for application in the fields such as, fashion, clothing, interior textiles; fashion accessories are some of the examples. For the fabrication of the composite, the sisal fibers were subjected to processes such as: chemical treatment with sodium hydroxide (NaOH) in the removal of impurities; bleaching for removing the yellowish color of the natural fiber and dyeing with direct dyes to confer the colors blue, green and orange. The search for new technologies ecologically correct has become a major concern in recent decades. Studies show that composite polymer reinforced by natural fibers is suitable for a large number of applications, and its use is advantageous in terms of economic and ecological. The dyed fibers were cut to a length of 30 mm, is used in the confection of webs. For this purpose, a web preparer by immersion, developed in the Laboratory of Chemical Textile of UFRN. The composite sheets measuring 300 x 300 x3 mm were molded by compression, with unsaturated orthophthalic polyester as matrix, and the samples in sizes 150 x 25 x 3 mm were cut with the aid of a laser machine, to be subjected to traction and flexion. The mechanical properties of traction and flexion in three points were performed in the Laboratory of metal and mechanical tests of Materials Engineering of UFRN. The resulting samples from the tests were evaluated in scanning electron microscope (SEM) at CTGas RN. On the basis of the analysis of the results from the mechanical tests, it was observed that the composite had good mechanical behavior, both in traction as in flexion. Furthermore, it was observed that in the water absorption test, the samples had a different percentage among themselves, this occurred due to the variation of density found in the fibre webs. The images of the SEM showed the failures from the manufacturing process and the adhesion of fibre/matrix. When the samples were prepared with the dyed fibers to be applied in fashion, the results were positive, and it can be concluded that the main objective of this work was achieved

Caracterização morfofisiológica de isolados do gênero Cylindrocladium

Com o objetivo de caracterizar o complexo gênero anamórfico Cylindrocladium, dezoito isolados foram cultivados em meios de cultura distintos, mantidos sob diferentes temperaturas, além de ter conídios e vesículas terminais analisados morfologicamente para identificação correta das culturas. Inoculações em diferentes hospedeiros foram, também, realizadas para avaliação do comportamento patogênico dos isolados estudados. Com relação aos caracteres morfológicos, pôde-se observar que ocorrem alterações nas dimensões de conídios e na morfologia da vesícula terminal devido, provavelmente, à mudança do substrato de cultivo. Porém, a variabilidade natural nas características dessas estruturas é tão elevada que dificulta a identificação correta dos isolados. em uma mesma cultura, por exemplo, foram observadas vesículas terminais de diferentes morfologias. Pôde-se constatar que existem diferenças patogênicas e fisiológicas entre os isolados, uma vez que houve a formação de grupos distintos quando tais características foram consideradas. Estas diferenças, provavelmente, sejam devidas à constituição genética distinta existente entre os isolados.

Ultrastructural features in the epididymis of the dog (Canis familiaris, L.)

The ultrastructure of the epididymal duct of the dog is described in this paper. The epididymis was divided into three morphofunctional segments: initial, middle and terminal. The cellular population of the lining epithelium is formed from principal, apical, basal and clear cells. The peritubular stroma and the tubular interstitium surrounding the epithelium are also described. The outcome is compared to the description made in other species of mammals.

O Desenvolvimento local sustentável no semi-árido nordestino: um estudo de caso na comunidade de mirandas, Caraúbas/RN

Brazil s semi-arid region is an immense territory characterized by a mosaic of natural environments and human settlements. Inside this multifaceted framework, there are problems that are specific to the region (the water resources situation, for example) while others are more universal (such as the inequality between men and women). The circumstances that give rise to these problems are complex and require a holistic view so that our understanding can go beyond the simple concept that this is a problem region . The semi-arid must be perceived as a viable area in need of a new analysis, taking into account its successes, limitations, challenges and the strategic public policy framework that guarantees its sustainable development. The dissertation analyzes, from a sustainable local development perspective, the experience of the Northeastern Brazil Groundwater Project (PROASNE), carried out from 2001 to 2003, in partnership with the Waters and Sewers Company of Rio Grande do Norte (CAERN) in the rural community of Mirandas, municipality of Caraúbas/RN, situated in the middle of the northeastern Brazil semi-arid region

PUPSI :uma proposta de processo unificado para políticas de segurança da informação

The way to deal with information assets means nowadays the main factor not only for the success but also for keeping the companies in the global world. The number of information security incidents has grown for the last years. The establishment of information security policies that search to keep the security requirements of assets in the desired degrees is the major priority for the companies. This dissertation suggests a unified process for elaboration, maintenance and development of information security policies, the Processo Unificado para Políticas de Segurança da Informação - PUPSI. The elaboration of this proposal started with the construction of a structure of knowledge based on documents and official rules, published in the last two decades, about security policies and information security. It's a model based on the examined documents which defines the needed security policies to be established in the organization, its work flow and identifies the sequence of hierarchy among them. It's also made a model of the entities participating in the process. Being the problem treated by the model so complex, which involves all security policies that the company must have. PUPSI has an interative and developing approach. This approach was obtained from the instantiation of the RUP - Rational Unified Process model. RUP is a platform for software development object oriented, of Rational Software (IBM group). Which uses the best practice known by the market. PUPSI got from RUP a structure of process that offers functionality, diffusion capacity and comprehension, performance and agility for the process adjustment, offering yet capacity of adjustment to technological and structural charges of the market and the company

Medição de desempenho organizacional nas imobiliárias: um estudo na cidade do Natal-RN

The purpose of this paper is to identify how real estate companies from the city of Natal measure their organizational performance. Traditionally these companies measure their performance using financial measures; however, the technological improvement, the internationalization of the economy and the change in consumer behavior all demand better products and services, and other measuring models. Those changes motivate organizations to continually improve the quality of their products and services. In this way, these companies need to associate their financial results to their global performance. Therefore, it is necessary to have organizational performance models that associate financial and non-financial measures to the strategies of the companies. The research also tries to identify which performance indicators are used by these companies, as well as to test a model who questions: a) if there is any relationship between managers´ characteristics and performance measuring systems´ characteristics; b) if there is any relationship between the company s characteristics and the characteristics of the measuring system used to evaluate its organizational performance and c) finally to verify if there is a relationship between the characteristics of the measuring system and the company s performance. The information which served as a basis for the study was obtained through an empirical research, with questionnaires, answered by 66 (sixty six) companies from the city of Natal, capital of the state of Rio Grande do Norte. The results show that none of the companies investigated use any of the performance measurement models proposed in the modern literature. However, they use on an isolated way some of the measures those models, including some measures from adopted in the Balanced Scorecard, as well as the benchmarking process, making comparisons with the performance of their competitors. The research also reveals that either bigger companies, companies with more experienced managers or with better performance show better performance measurement systems

Uso do GPR na geração de modelos estáticos 3D para o planejamento de lavra de minerais pesados depositados em dunas eólicas

This project was developed as a partnership between the Laboratory of Stratigraphical Analyses of the Geology Department of UFRN and the company Millennium Inorganic Chemicals Mineração Ltda. This company is located in the north end of the paraiban coast, in the municipal district of Mataraca. Millennium has as main prospected product, heavy minerals as ilmenita, rutilo and zircon presents in the sands of the dunes. These dunes are predominantly inactive, and overlap the superior portion of Barreiras Formation rocks. The mining happens with the use of a dredge that is emerged at an artificial lake on the dunes. This dredge removes sand dunes of the bottom lake (after it disassembles of the lake borders with water jets) and directs for the concentration plant, through piping where the minerals are then separate. The present work consisted in the acquisition external geometries of the dunes, where in the end a 3D Static Model could be set up of these sedimentary deposits with emphasis in the behavior of the structural top of Barreiras Formation rocks (inferior limit of the deposit). The knowledge of this surface is important in the phase of the plowing planning for the company, because a calculation mistake can do with that the dredge works too close of this limit, taking the risk that fragments can cause obstruction in the dredge generating a financial damage so much in the equipment repair as for the stopped days production. During the field stages (accomplished in 2006 and 2007) topographical techniques risings were used with Total Station and Geodesic GPS as well as shallow geophysical acquisitions with GPR (Ground Penetrating Radar). It was acquired almost 10,4km of topography and 10km of profiles GPR. The Geodesic GPS was used for the data geopositioning and topographical rising of a traverse line with 630m of extension in the stage of 2007. The GPR was shown a reliable method, ecologically clean, fast acquisition and with a low cost in relation to traditional methods as surveys. The main advantage of this equipment is obtain a continuous information to superior surface Barreiras Formation rocks. The static models 3D were elaborated starting from the obtained data being used two specific softwares for visualization 3D: GoCAD 2.0.8 and Datamine. The visualization 3D allows a better understanding of the Barreiras surface behavior as well as it makes possible the execution of several types of measurements, favoring like calculations and allowing that procedures used for mineral extraction is used with larger safety

Autopsy: quality assurance in the ICU

Objective: To examine the correlation between the clinical diagnosis and autopsy findings in adult patients who died in an intensive care unit (ICU). To determine the rate of agreement of the basic and terminal causes of death and the types of errors in order to improve quality control of future care,Design, Retrospective study.Setting: Adult ICU in a university hospital.Patients: 30 adult patients who died in the ICU. with the exclusion of medicolegal cases.Methods and main results: Anatomo-clinical meetings were held to analyze the pre- and postmortem correlations in 30 consecutive autopsies at the ICU of the University Hospital, School of Medicine of Botucatu/ UNESP, from January 1994 to January 1997. The rate of correct clinical diagnoses of the basic cause was 66.7 %; in 23.3 % of cases, if the correct diagnosis was made, management would have been different, as would have been the evolution of the patient's course (Class I error): in 10 % of the cases the error would not have led to a change in management (Class II error). The rate of correct clinical diagnoses of terminal cause was 80 %.Conclusions: the rate of recognition of the basic cause was 66.7 %, which is consistent with the literature, but the Class I error rate was higher than that reported in the literature.

Da vigilância para prevenção de acidentes de trabalho: contribuição da ergonomia da atividade

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)