Modelos para análise e dimensionamento de painéis de alvenaria estrutural

The main objective of this thesis was the study of bracing panels of structural masonry, by applying the Finite Element Method and Strut and Tie Method. It was analyzed the following aspects: the effect of orthotropy on the behavior of the panels; distribution of horizontal forces between panels for buildings; comparison between Equivalent Frame and Finite Elements models; panels design with the Strut and Tie Method. The results showed that one should not disregard the orthotropy, otherwise this can lead to models stiffer than the real. Regarding the distribution of horizontal forces, showed that the disregard of lintels and shear deformation leads to significant differences in the simplified model. The results showed also that the models in Finite Element and Equivalent Frame exhibit similar behavior in respect to stiffness of panels and stress distribution over the sessions requested. It was discussing criteria for designing Strut and Tie Method models in one floor panels. Then, the theoretical strength these panels was compared with the rupture strength of panels tested in the literature. The theoretical maximum strength were always less than the rupture strength of the panels obtained in tests, due to the fact that the proposed model cannot represent the behavior of the masonry after the start of the panel cracking due to plasticization of the reinforcement

Efeito de doses de calcário e de gesso na cultura do feijoeiro (Phaseolus vulgaris L.) cv. Carioca-80

Instalou-se em um latossolo vermelho-escuro, textura média, de Jaboticabal, S.P. um experimento cujo objetivo foi avaliar a influência de doses de gesso e de calcário sobre as características químicas do solo, agronômicas e tecnológicas da cultura do feijoeiro. Utilizou-se o delineamento em blocos casualizados em um esquema fatorial 3 x 4, representado por três doses de calcário (0; 1,4 e 2,8 t/ha) e quatro doses de gesso (0, 130, 260 e 390 kg/ha) com três repetições. Verificou-se que: o uso do calcário provocou aumento nos teores do Mg trocável do solo, nos valores de pH e de V% e diminuição dos valores de H + Al; o fornecimento de gesso ocasionou a lixiviação do K trocável da camada superficial para a camada 20-40cm do solo; os teores foliares de Mg+2 aumentaram e os de Mn+2 diminuiram com a aplicação de calcário; a calagem e/ou a gessagem não influenciaram nos componentes de rendimento e na produção de grãos, provocando aumento no tempo de cozimento dos grãos.

Efeito de modos e épocas de aplicação de gesso e calcário sobre a cultura do feijoeiro (Phaseolus vulgaris L.) cv. Carioca-80

Instalou-se sobre um latossolo vermelho-escuro textura média, um experimento cujo objetivo foi avaliar a influência de modos e épocas de aplicação de gesso e de calcário sobre algumas características nutricionais e tecnológicas da cultura do feijoeiro irrigado. Utilizou-se no experimento o delineamento em blocos casualizados em esquema fatorial (4x3)+2 com quatro repetições, correspondendo a 4 modos de aplicação de gesso e/ou calcário, 3 doses de gesso e 2 tratamentos adicionais. Os resultados mostraram que: o uso do gesso proporcionou maiores teores de Ca nos grãos e consequentemente maior tempo para o seu cozimento. A associação gesso e calcário propiciou aumento no teor de S das folhas e também no peso de 100 grãos, quando comparado à utilização de apenas gesso. A relação de hidratação diminuiu com o aumento das doses de gesso quando utilizou-se os modos de aplicação M1 (gesso aplicado no solo 45 dias antes da semeadura) e M2 (gesso e calcário aplicados conjuntamente aos 45 dias antes da semeadura).

A comparison of statistical methods for genomic selection in a mice population

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dinâmica do surgimento de brotos de alfafa em função de diferentes fontes de fósforo, da aplicação de gesso e do momento de calagem

O fósforo (P) é um importante nutriente para o surgimento de brotos em alfafa. Através do estudo da dinâmica do aparecimento de brotos pode-se obter informações que auxiliam na adoção de um manejo eficiente. Diversas fontes de P estão disponíveis no mercado, sendo que a eficiência deste nutriente é afetada pela acidez do solo. O uso do gesso com fosfato de rocha pode corrigir o perfil do solo em relação ao alumínio e diminuir a fixação de P. Num experimento conduzido em vasos, superfosfato triplo (ST), fosfato de Gafsa (FG) e FG com gesso, aplicados antes e depois da calagem, foram avaliados para se estudar o número de brotos laterais e basais em alfafa, assim como a dinâmica do surgimento destes brotos em função das seguintes doses: 0, 50, 100 e 200 mg P dm-3. A avaliação envolveu três cortes da cultura. A dose de 100 mg P dm-3 retardou em 6 a 15 dias o surgimento do segundo broto basal quando comparada à dose de 200 mg P dm-3. Os brotos laterais surgiram 24 dias após o aparecimento dos brotos basais quando empregou-se a dose de 200 mg P dm-3. A adição de fósforo aumentou o número de brotos basais e laterais de 1,5 e 0,5 broto/planta para 8,0 e 6,9 brotos/planta, respectivamente. Verificou-se um maior número de hastes basais com a utilização do FG (5,1 brotos/planta) do que com o uso de ST (2,9 brotos/planta). Não houve efeito do gesso sobre os brotos laterais. O uso do FG mais gesso resultou em 5,9 brotos basais/planta, enquanto que o uso do FG não combinado com gesso resultou em 3,9 brotos basais/planta. Não houve efeito do momento de calagem sobre o número de brotos da alfafa.

Propriedades físicas e mecânicas de painéis LVL de Eucalyptus grandis

This paper mainly aimed to evaluate the physical and mechanical properties of LVL panels made from Eucalyptus grandis, from reforestation at the region of Senges, in Parana state, Brazil. LVL panels were manufactured using 23 veneers (2,4mm thick each one) in commercial dimension of 2.500 mm long and 1,200 mm wide. The properties of static bending were analyzed (strength and rigidity) in beams of the LVL, in the flatwise and edgewise positions. The properties of compression parallel to grain and shear parallel in the plans L-X and L-Y and density in this LVL panels were also analyzed according to ASTM-D 5456/4761 and ASTM-D 198 codes. The mean values to flatwise bending MOE and MOR were 13114 MPa and 88.76 MPa, respectively, and for edgewise bending MOE and MOR were 15871 MPa and 88.63 MPa, respectively. The density (12%) of the LVL panels and of the veneers were 690 kg/m(3) and 649 kg/m(3). The mean values to parallel compression MOE and MOR were 16856 MPa and 58.05 MPa, respectively. The mean values of the maximum resistance to shear parallel in the plans L-X and L-Y were 5.96 MPa and 591 MPa, respectively. All these values reached partially or they passed the medium limits of reference (normative codes, researches and commercial catalogs) established for LVL panels and original solid wood, attesting overall the quality of those panels produced with this wood.

Análise do espalhamento espectral em superfícies de estruturas complexas para comunicações móveis

In this work, the transmission line method is explored on the study of the propagation phenomenon in nonhomogeneous walls with finite thickness. It is evaluated the efficiency and applicability of the method, considering materials like gypsum, wood and brick, found in the composition of the structures of walls in question. The results obtained in this work are compared to those available in the literature, for several particular cases. A good agreement is observed, showing that the performed analysis is accurate and efficient in modeling, for instance, the wave propagation through building walls and integrated circuit layers in mobile communication and radar system applications. Later, simulations of resistive sheets devices such as Salisbury screens and Jaumann absorbers and of transmission lines made of metal-insulator-semiconductor (MIS) are made. Thereafter, it is described a study on frequency surface selective structures (FSS). It is proposed the development of devices and microwave integrated circuits (MIC) of such structures, for the accomplishment of experiments. Finally, future works are suggested, for instance, on the development of reflectarrays, frequency selective surfaces with dissimilar elements, and coupled frequency selective surfaces with elements located on different layers

Medição da densidade óssea através de ondas eletromagnéticas e classificação por MVS

This work holds the purpose of presenting an auxiliary way of bone density measurement through the attenuation of electromagnetic waves. In order to do so, an arrangement of two microstrip antennas with rectangular configuration has been used, operating in a frequency of 2,49 GHz, and fed by a microstrip line on a substrate of fiberglass with permissiveness of 4.4 and height of 0,9 cm. Simulations were done with silica, bone meal, silica and gypsum blocks samples to prove the variation on the attenuation level of different combinations. Because of their good reproduction of the human beings anomaly aspects, samples of bovine bone were used. They were subjected to weighing, measurement and microwave radiation. The samples had their masses altered after mischaracterization and the process was repeated. The obtained data were inserted in a neural network and its training was proceeded with the best results gathered by correct classification on 100% of the samples. It comes to the conclusion that through only one non-ionizing wave in the 2,49 GHz zone it is possible to evaluate the attenuation level in the bone tissue, and that with the appliance of neural network fed with obtained characteristics in the experiment it is possible to classify a sample as having low or high bone density

Estudo térmico e de materiais de um compósito à base de gesso e EPS para construção de casas populares

A housing unit was built to study the thermal performance, and of material using a composite made of gypsum and EPS ground. We used two techniques of construction, using blocks, and filling on the spot. Two compositions of the composite were studied. The blocks were fixed using conventional mortar. In the technical of filling on the spot were used PET bottles up inside the walls to provide mechanical and thermal resistance. Compression tests were realized according to the ABNT standard of sealing bricks. It is going to be shown an analysis of the thermal comfort through the use of thermocouples placed on the walls of the building, internally and externally. The manufacturing viability of houses, using recyclable materials, through the use of composite materials proposed will be demonstrated. The constructive aspects showing the advantages and disadvantages of the technique used also will be broached. The block used presents structural functions and thermal insulating, is low cost and represents an alternative to the use of EPS and PET bottles which are materials that end up occupying much space in the landfills, giving than an ecologically correct use. The results of thermal analysis shows the thermal comfort provided by the composite by the obtainment of a difference between the internal and external surfaces of the walls more exposed to the sun around 7º C. The average temperature of the air inside the building, around 28.0 º C was below the zone of thermal comfort recommended for countries with hot weather

Estudo do aproveitamento de resíduo de gesso como carga para compósito com matriz de resina expansiva de mamona

In the execution of civil engineering works, either by wasting during the coating of wall or demolition of gypsum walls, the generation of the gypsum waste involves serious environmental concerns. These concerns are increased by the high demand of this raw material in the sector and by the difficulties of proper disposal byproduct generated. In the search for alternatives to minimize this problem, many research works are being conducted, giving emphasis in using gypsum waste as fillers in composites materials in order to improve the acoustic, thermal and mechanical performances. Through empirical testing, it was observed that the crystallization water contained in the residue (CaSO4.2H2O) could act like primary agent in the expanding of the polyurethane foam. Considering that polyurethane produced from vegetable oils are biodegradable synthetic polymers and that are admittedly to represent an alternative to petrochemical synthetic polyurethane, this research consist an analysis of the thermal behavior of a composite whose matrix obtained from a resin derived from the expansive castor oil seed, with loads of 4%, 8%, 12% and 16% of gypsum waste replacing to the polyol prepolymer blend. Contributors to this analysis: a characterization of the raw material through analysis of spectroscopy by Fourier transform infrared (FTIR), chemical analysis by X-Ray Fluorescence (XRF) and mineralogical analysis by X Ray Diffraction (XRD), complemented by thermo gravimetric analysis (TGA). In order to evaluate the thermo physical properties and thermal behavior of the composites manufactured in die closed with expansion contained, were also carried tests to determine the percentage of open pore volume using a gas pycnometer, scanning electronic microscopy (SEM), in addition to testing of flammability and the resistance to contact with hot surfaces. Through the analysis of the results, it appears that it is possible to produce a new material, which few changes in their thermo physical properties and thermal performance, promotes significant changes and attractive to the environment

Desempenho de um painel fotovoltaico de baixa tensão, acoplado ao protótipo de um conversor dc/dc topologia Booster

Low voltage solar panels increase the reliability of solar panels due to reduction of in series associations the configurations of photovoltaic cells. The low voltage generation requires DCDC converters devices with high efficiency, enabling raise and regulate the output voltage. This study analyzes the performance of a photovoltaic panel of Solarex, MSX model 77, configured to generate an open circuit voltage of 10.5 V, with load voltage of 8.5 V, with short circuit current of 9 A and a power of 77 W. The solar panel was assembled in the isolated photovoltaic system configuration, with and without energy storage as an interface with a DCDC converter, Booster topology. The converter was designed and fabricated using SMD (Surface Mounted Devices) technology IC (integrated circuit) that regulates its output voltage at 14.2 V, with an efficiency of 87% and providing the load a maximum power of 20.88 W. The system was installed and instrumented for measurement and acquisition of the following data: luminosities, average global radiation (data of INPE Instituto Nacional de Pesquisas Espaciais), solar panel and environment temperatures, solar panel and DC-DC converter output voltages, panel, inverter, and battery charge output currents. The photovoltaic system was initially tested in the laboratory (simulating its functioning in ideal conditions of operation) and then subjected to testing in real field conditions. The panel inclination angle was set at 5.5°, consistent with the latitude of Natal city. Factors such as climatic conditions (simultaneous variations of temperature, solar luminosities and ra diation on the panel), values of load resistance, lower limit of the maximum power required by the load (20.88 W) were predominant factors that panel does not operate with energy efficiency levels greater than 5 to 6%. The average converter efficiency designed in the field test reached 95%

Simulação numérica da interação entre uma nuvem incidente de vórtices e uma aerofólio através do método dos vórtices

The study of aerodynamic loading variations has many engineering applications, including helicopter rotor blades, wind turbines and turbo machinery. This work uses a Vortex Method to make a lagrangian description of the a twodimensional airfoil/ incident wake vortex interaction. The flow is incompressible, newtonian, homogeneus and the Reynolds Number is 5x105 .The airfoil is a NACA 0018 placed a angle of attack of the 0° and 5°simulates with the Painel Method with a constant density vorticity panels and a generation poit is near the painel. The protector layer is created does not permit vortex inside the body. The vortex Lamb convection is realized with the Euler Method (first order) and Adans-Bashforth (second order). The Random Walk Method is used to simulate the diffusion. The circular wake has 366 vortex all over positive or negative vorticity located at different heights with respect to the airfoil chord. The Lift was calculated based in the algorithm created by Ricci (2002). This simulation uses a ready algorithm vatidated with single body does not have a incident wake. The results are compared with a experimental work The comparasion concludes that the experimental results has a good agrement with this papper

Estudo de um compósito de matriz cerâmica com carga de recicláveis para o uso na construção civi

With a view to revitalizing public environments through criteria that include economy, tourism, aesthetics and respect for the environment, this paper proposes a model of kiosk manufactured with composite material blocks, to be employed as a public instrument. . The model consists of a structure composed of planned blocks and manufactured in cement-based composite, gypsum, ground and water, having the styrofoam inside filled with pet bottles of 500 ml dose. The social and environmental issue is the critical point of the work when it can, through the reuse of environmentally harmful materials such as polyethylene terephthalate PET, using such modules for the construction of various areas of Commerce, promoting the protection of the environment combined with the improvement of the quality of life of the population. The tourism factor, which is significant in the economy of the North, is also considered as the modulated kiosk has a visual aspect innovative and differentiated. The environmental issue is addressed by encouraging the reuse of PET material and EPS (polystyrene)

Productivity, biological efficiency, and number of Agaricus blazei mushrooms grown in compost in the presence of Trichoderma sp. and Chaetomium olivacearum contaminants

Foi avaliado o efeito dos fungos contaminantes Trichoderma sp. e C. olivacearum na produtividade, eficiência biológica e número de cogumelos da produção do A. blazei em composto (mistura de cana-de-açúcar, palha de capim coast-cross, farelo de soja, gesso e calcário calcítico). O delineanamento foi inteiramente casualizado com três tratamentos (Trichoderma sp., C. olivacearum e testemunha) e oito repetições (caixa com 12 kg de composto colonizado com A. blazei). Após a colonização do composto pelo A. blazei, adicionou-se 150g de inóculo à base de triticale de cada um dos fungos contaminantes na superfície do composto seguido da camada de cobertura. O experimento foi conduzido em estufa com cobertura plástica, umidade relativa entre 60-90% e temperatura de 20-34ºC. A produtividade foi determinada pela relação entre a massa fresca de basidiomas e a massa úmida do composto. A eficiência biológica foi determinada pela relação entre a massa fresca de basidiomas e a massa seca do composto ao final do período de colheita. de acordo com os resultados obtidos, os fungos contaminantes C. olivacearum e Trichoderma sp. não afetaram a produtividade, eficiência biológica e número de cogumelos da produção do A. blazei em compostos previamente colonizados.

Otimização do tempo e temperatura no processamento da gipsita oriunda dos cristalizadores da produção de sal para obter gesso de uso na construção civil

During the process of the salt production, the first the salt crystals formed are disposed of as industrial waste. This waste is formed basically by gypsum, composed of calcium sulfate dihydrate (CaSO4.2H2O), known as carago cru or malacacheta . After be submitted the process of calcination to produce gypsum (CaSO4.0,5H2O), can be made possible its application in cement industry. This work aims to optimize the time and temperature for the process of calcination of the gypsum (carago) for get beta plaster according to the specifications of the norms of civil construction. The experiments involved the chemical and mineralogical characterization of the gypsum (carago) from the crystallizers, and of the plaster that is produced in the salt industry located in Mossoró, through the following techniques: x-ray diffraction (XRD), x-ray fluorescence (FRX), thermogravimetric analysis (TG/DTG) and scanning electron microscopy (SEM) with EDS. For optimization of time and temperature of the process of calcination was used the planning three factorial with levels with response surfaces of compressive mechanical tests and setting time, according norms NBR-13207: Plasters for civil construction and x-ray diffraction of plasters (carago) beta obtained in calcination. The STATISTICA software 7.0 was used for the calculations to relate the experimental data for a statistical model. The process for optimization of calcination of gypsum (carago) occurred in the temperature range from 120° C to 160° C and the time in the range of 90 to 210 minutes in the oven at atmospheric pressure, it was found that with the increase of values of temperature of 160° C and time calcination of 210 minutes to get the results of tests of resistance to compression with values above 10 MPa which conform to the standard required (> 8.40) and that the X-ray diffractograms the predominance of the phase of hemidrato beta, getting a beta plaster of good quality and which is in accordance with the norms in force, giving a by-product of the salt industry employability in civil construction