How to achieve sustainability : regulatory challenges

The importance of designing sustainable buildings is gaining greater acceptance worldwide. Evidence of this is how regulators are incorporating sustainable design principles into building regulations and requirements. The aim being to increase the number of sustainable buildings and move from a traditional voluntary compliance to one that is mandatory. However, developing regulations that actually achieve these aims can be a difficult exercise. Several countries in South East Asia, such as Singapore and Malaysia, have performance based building regulations that are supplemented by prescriptive measures for achieving the desired performance. Australia too has similar building regulations and has had energy efficiency regulations within the Building Code of Australia for over a decade. This paper explores some of the difficulties and problems that Australian regulators have experienced with the performance-based method and the prescriptive or “deemed-to-comply” method and measures that have been taken to try and overcome these problems. These experiences act as a useful guide to all regulators considering the incorporation of sustainable design measures into their countries building regulations. The paper also speculates on future environmental requirements being incorporated into regulations, including the possibility of non-residential buildings being required to meet minimum energy efficiency requirements, and the possible systems that would need to be in place before such requirements were included. Finally, the paper looks at a possible way forward using direct assessment from electronic designs and introduces several software tools that are currently being developed that move towards achieving this goal. Keywords: Sustainable buildings, Performance-based, Regulations, Energy efficiency, Assessment tools.

Citizen journalism and political participation : the youdecide project and the 2007 Australian Federal Election

The 2007 Australian Federal election not only saw the election of a Labor government after 11 years of John Howard’s conservative Coalition government. It also saw new levels of political engagement through the Internet, including the rise of citizen journalism as an alternative outlet and mode of reporting on the election. This paper reports on the You Decide 2007 project, an initiative undertaken by a QUT-based research team to facilitate online news reporting on the election on a ‘hyper-local’, electorate-based model. We evaluate the You Decide initiative on the basis of: promoting greater citizen participation in Australian politics; new ways of engaging citizens and key stakeholders in policy deliberation; establishing new links between mainstream media and independent online media; and broadening the base of political participation to include a wider range of citizen and groups.

The effect of social support derived from World of Warcraft on negative psychological symptoms

Previous research examining players of Massively-Multiplayer Online Games (MMOGs) suggests that players form meaningful relationships with each other. Other research indicates that people may derive social support from online sources and this social support has been associated with greater wellbeing. This study used an online survey of players (N = 206) of the MMOG “World of Warcraft” (WoW) to examine if social support can be derived from MMOGs, and to examine its relationship with negative psychological symptoms. Players of WoW were found to derive social support from playing and a positive relationship was found between game engagement and levels of in-game social support. Higher levels of in-game social support were associated with fewer negative psychological symptoms, although this effect was not maintained after accounting for social support derived from the offline sources. Additionally, a small subsample of players (N = 21) were identified that played for between 44 and 82 hours per week (M = 63.33). These players had significantly lower levels of offline social support and higher levels of negative symptoms compared to the rest of the sample. This study provides evidence that social support can be derived from MMOGs and the associated potential to promote well being, but also highlights the potential harm from spending excessive hours playing.

Teaching young people first aid skills to reduce injury

Background First aid given immediately after a motor vehicle crash can have considerable benefits. Less understood however is first aid training as a prevention strategy for reducing risk-taking. A first step is to understand whether first aid skills are associated with risk-taking and injury experiences. Further, students and teachers who undergo or deliver such training offer important perspectives about implementation. Aims The research has two aims: (i) to identify whether first aid knowledge is associated with road risk-taking and injury and (ii) to examine teachers’ and students’ experiences of first aid activities within a school-based injury prevention and control program. Method Participants were 173 Year 9s (47% male) who completed a survey which included demographic information, first aid knowledge and risk-taking behaviour and injury experiences. Focus groups were held with 8 teachers who delivered, and 70 students who participated in, a school-based injury prevention and control program. Results Results showed a relationship between greater first aid knowledge and reduced engagement in risk-taking and injury experiences. Both students and teachers reported favourably on first aid however teachers also acknowledged challenges in delivering practical activities. Discussion & Conclusion It appears that first aid can be implemented within the school setting, particularly at the Year 9 level, and that both students and teachers involved in such training identify multiple benefits and positive experiences with first aid training. In addition, the findings suggest that first aid knowledge could be an important part of a prevention program.

Adolescent protective behaviour to reduce drug and alcohol use, alcohol-related harm and interpersonal violence

Typically adolescents' friends are considered a risk factor for adolescent engagement in risk-taking. This study took a more novel approach, by examining adolescent friendship as a protective factor. In particular it investigated friends' potential to intervene to reduce risk-taking. 540 adolescents (mean age 13.47 years) were asked about their intention to intervene to reduce friends' alcohol, drug and alcohol-related harms and about psychosocial factors potentially associated with intervening. More than half indicated that they would intervene in friends' alcohol, drug use, alcohol-related harms and interpersonal violence. Intervening was associated with being female, having friends engage in overall less risk-taking and having greater school connectedness. The findings provide an important understanding of increasing adolescent protective behavior as a potential strategy to reduce alcohol and drug related harms.

Promoting the use of cycling as an environmentally and socially sustainable form of transport.

Solar Cities Congress 2008 “Energising Sustainable Communities – Options for Our Future” THEME 3: Climate Change. Impact on Society and Culture. Sub Theme: planning and implementing holistic strategies for sustainable transport Abstract Promoting the use of cycling as an environmentally and socially sustainable form of transport. We need to reduce carbon emissions. We need to reduce fuel consumption. We need to reduce pollution. We need to reduce traffic congestion. As obesity levels and associated health problems in the developed nations continue to increase we need to adopt a healthier lifestyle. Few if any would argue with these statements. In fact many would consider these problems to be amongst the most urgent that our society faces. What if we had a vehicle that uses no fossil fuel to power it, creates no pollution, takes up far less space on the roads and promotes an active, healthy lifestyle. What if this machine would have energy efficiency levels 50 times greater than the car? This is a solution that is here, now and ready to go and many of us already own one. It is the humble bicycle. Although bicycle sales in Australia now outnumber car sales, bicycle use as a form of transport (as opposed to recreation) only constitutes around 3% to 4% of all trips. So, why are bicycles the forgotten form of transport if they promise to deliver the benefits that I have just outlined? This paper examines the underlying reasons for the relatively low use of bicycles as a means of transport. It identifies the areas of greatest potential for encouraging the use of the world’s most efficient form of transport. Tim Williams - May 2007

Social Awareness Concepts to Support Social Computing

Our social life is characterised by norms that manifest as attitudinal and behavioural uniformities among people. With greater awareness about our social context, we can interact more efficiently. Any theory or account of human interaction that fails to include social concepts could be suggested to lack a critical element. This paper identifies social concepts that need to be supported by future context-aware systems. It discusses the limitations of existing context-aware and Multi-Agent Systems (MAS) to support social psychology theories related to the identification and membership of social groups. We argue thatsocial norms are among the core modeling concepts that future context-aware systems need to capture with the view to support and enhance social interactions. The social concepts identified in this paper could be used to simulate agent interactions imbued with social norms or use ICT to facilitate, assist or enhance social interactions. They also could be used in virtual communities modeling where the awareness of a community as well as the process of joining and exiting a community are important.

Project diagnostics : assessing the condition of projects and identifying poor health combing forces

In many cases, construction projects do not achieve the objectives that the project participants set for them. If participants could better understand how their project is performing overall, at various stages of its delivery, then the opportunities to achieve project success would almost certainly be greater. This paper documents a method of assessing the status of a project, at a point in its design or construction phase, or after completion. The status is assessed in terms of up to seven (7) key success factors. Any evidence of less than adequate performance in these performance areas is scrutinised to seek out the root causes of why this situation is happening. Using these identified root causes of under performance, general suggestions can then be made as to how to return the project to good health. A software package that assists in assessing the status of the project has been developed. The package is currently being calibrated before commercial release.

The effect of insertion time on the axial pullout strength of anterior vertebral body screws

Top screw pullout occurs when the screw is under too much axial force to remain secure in the vertebral body. In vitro biomechanical pullout tests are commonly done to find the maximum fixation strength of anterior vertebral body screws. Typically, pullout tests are done instantaneously where the screw is inserted and then pulled out immediately after insertion. However, bone is a viscoelastic material so it shows a time dependent stress and strain response. Because of this property, it was hypothesised that creep occurs in the vertebral trabecular bone due to the stress caused by the screw. The objective of this study was therefore to determine whether the axial pullout strength of anterior vertebral body screws used for scoliosis correction surgery changes with time after insertion. This study found that there is a possible relationship between pullout strength and time; however more testing is required as the sample numbers were quite small. The design of the screw is made with the knowledge of the strength it must obtain. This is important to prevent such occurrences as top screw pullout. If the pullout strength is indeed decreased due to creep, the design of the screw may need to be changed to withstand greater forces.

Synthesis and Raman spectroscopic study of Mg/Al,Fe hydrotalcites with variable cationic ratios

Hydrotalcites of formula Mg6 (Fe,Al)2(OH)16(CO3).4H2O formed by intercalation with the carbonate anion as a function of divalent/trivalent cationic ratio have been successfully synthesised. The XRD patterns show variation in the d-spacing attributed to the size of the cation. Raman and infrared bands in the OH stretching region are assigned to (a) brucite layer OH stretching vibrations (b) water stretching bands and (c) water strongly hydrogen bonded to the carbonate anion. Multiple (CO3)2- symmetric stretching bands suggest that different types of (CO3)2- exist in the hydrotalcite interlayer. Increasing the cation ratio (Mg/Al,Fe) resulted in an increase in the combined intensity of the 2 Raman bands at around 3600 cm-1, attributed to Mg-OH stretching modes, and a shift of the overall band profile to higher wavenumbers. These observations are believed to be a result of the increase in magnesium in the structure. Raman spectroscopy shows a reduction in the symmetry of the carbonate, leading to the conclusion that the anions are bonded to the brucite-like hydroxyl surface and to the water in the interlayer. Water bending modes are identified in the infrared spectra at positions greater than 1630 cm-1, indicating the water is strongly hydrogen bonded to both the interlayer anions and the brucite-like surface.

Best Practice Guide : Generic Overview

The construction industry is a key national economic component. It tends to be at the forefront of cyclic changes in the Australian economy. It has a significant impact, both directly and indirectly, on the efficiency and productivity of other industries. Moreover it affects everyone to a greater or lesser extent; through its products whether they are manifested in the physical infrastructure that supports the operation of the economy or through the built environment that directly impacts on the quality of life experienced by individuals. In financial terms the industry makes one of the largest contributions to the Australian economy, accounting for 4.7 per cent of GDP 1 which was worth over $30B in 20012. The construction industry is comprised of a myriad of small firms, across several important sectors including, o Residential building, o Commercial building, o Building services, o Engineering, o Infrastructure o Facilities Management o Property Development Each sector is typified by firms that have distinctive characteristics such as the number of employees, size and value of contracts, number of jobs, and so forth. It tends to be the case that firms operating in commercial building are larger than those involved in residential construction. The largest contractors are found in engineering and infrastructure, as well as in the commercial building sub-sectors. However all sectors are characterised by their reliance upon sub-contractors to carry out on-site operations. Professionals from the various design consultant groups operate across all of these sectors. This description masks one of the most significant underlying causes of inefficiency in the construction industry, namely its fragmentation. The Construction Industry chapter of the 2004 Australian Year Book3, published by the Australian Bureau of Statistics unmasks the industry’s fragmented structure, typified by the large number of operating businesses within it, the vast majority of which are small companies employing less than 5 people. It identifies over 190,000 firms, of which over 90 percent employ less than 5 people. At the other end of the spectrum, firms employing 20 or more people account for fractionally more than one percent of businesses in the industry.

Understanding preservice teachers’ predispositions for teaching engineering education in Australian schools.

Engineering education is underrepresented in Australia at the primary, middle school and high school levels. Understanding preservice teachers’ preparedness to be involved in engineering will be important for developing an engineering curriculum. This study administered a literature-based survey to 36 preservice teachers, which gathered data about their perceptions of engineering and their predispositions for teaching engineering. Findings indicated that the four constructs associated with the survey had acceptable Cronbach alpha scores (i.e., personal professional attributes .88, student motivation .91, pedagogical knowledge .91, and fused curricula .89). However, there was no “disagree” or “strongly disagree” response greater than 22% for any of the 25 survey items. Generally, these preservice teachers indicated predispositions for teaching engineering in the middle school. Extensive scaffolding and support with education programs will assist preservice teachers to develop confidence in this field. Governments and education departments need to recognise the importance of engineering education, and universities must take a stronger role in developing engineering education curricula.

Varieties of Asian capitalism : toward an institutional theory of Asian enterprise

In this paper we respond to calls for an institution-based perspective on strategy. With its emphasis upon mimetic, coercive, and normative isomorphism, institutional theory has earned a deterministic reputation and seems an unlikely foundation on which to construct a theory of strategy. However, a second movement in institutional theory is emerging that gives greater emphasis to creativity and agency. We develop this approach by highlighting co-evolutionary processes that are shaping the varieties of capitalism (VoC) in Asia. To do so, we examine the extent to which the VoC model can be fruitfully applied in the Asian context. In the spirit of the second movement of institutional theory, we describe three processes in which firm strategy collectively and intentionally feeds back to shape institutions: (1) filling institutional voids, (2) retarding institutional innovation, and (3) deploying institutional escape. We outline the key contributions contained in the articles of this Special Issue and discuss a research agenda generated by the VoC perspective.

Simulations of pollutant dispersion at toll plazas using three-dimensional CFD models

Toll plazas are particularly susceptible to build-ups of vehicle-emitted pollutants because vehicles pass through in low gear. To look at this, three-dimensional computational fluid dynamics simulations of pollutant dispersion are used on the standard k e turbulence model. The effects of wind speed, wind direction and topography on pollutant dispersion were discussed. The Wuzhuang toll plaza on the Hefei-Nanjing expressway is considered, and the effects of the retaining walls along both sides of the plaza on pollutant dispersion is analysed. There are greater pollutant concentrations near the tollbooths as the angle between the direction of the wind and traffic increases implying that retaining walls impede dispersion. The slope of the walls has little influence on the variations in pollutant concentration.

An application of Keller’s brand equity model in a B2B context

Purpose – The importance of branding in industrial contexts has increased, yet a comprehensive model of business-to-business (B2B) branding does not exist, nor has there been a thoroughempirical study of the applicability of a full brand equitymodel in a B2B context. This paper aims to discuss the suitability and limitations of Keller’s customer-based brand equity model and tests its applicability in a B2B market. Design/methodology/approach – The study involved the use of semi-structured interviews with senior buyers of technology for electronic tracking of waste management. Findings – Findings suggest that amongst organisational buyers there is a much greater emphasis on the selling organisation, including its corporate brand, credibility and staff, than on individual brands and their associated dimensions. Research limitations/implications – The study investigates real brands with real potential buyers, so there is a risk that the results may represent industry-specific factors that are not representative of all B2B markets. Future research that validates the importance of the Keller elements in other industrial marketing contexts would be beneficial. Practical implications – The findings are relevant for marketing practitioners, researchers and managers as a starting-point for their B2B brand equity research. Originality/value – Detailed insights and key lessons from the field with regard to how B2B brand equity should be conceptualised and measured are offered. A revised brand equity model for B2B application is also presented.