辽东湾隐蔽油气藏地球物理识别技术研究

In China and world, more than half the recent basin discovered reserves involve lithologic hydrocarbon reservoir reserves. The major target for further hydrocarbon basin exploration is the subtle reservoir. The Liaodong Bay prospect is much important in Bohai Sea, which includes Liaoxi low uplift, Liaodong uplift, Liaoxi sag and Liaozhong sag. After dozens years’ exploration in Liaodong Bay, few unexplored big-and-middle-sized favorable structural traps are remained and most of the stock structure targets are bad for fragmentary. Thus seeking for new prospect area and making a breakthrough, have become the unique way to relieve the severe exploration condition in Liaodong Bay. Technique Route Based on the petrophysical property of target area, the seismic forward inference of typical subtle trap model is expanded with analysis of logging, seismic and geologic data. According to petrophysical characteristics and forward inference and research on seismic response of actual seismic data in target area, the optimization of geophysical technique is used in subtle trap identification and the geophysical identification technique system of subtle reservoir is formed. The Key Research ① Petrophysical Model The petrophysical parameter is the basic parameter for seismic wave simulation. The seismic response difference of rocks bearing different fluids is required. With the crossplot of log data, the influence of petrophysical parameters on rock elastic properties of target area is analyzed, such as porosity, shale index, fluid property and saturation. Based on the current research on Biot-Gassmann and Kuster-Toksoz model, the petrophysical parameter calculator program which can be used for fluid substitution is established. ② S-wave evaluation based on conventional log data The shear velocity is needed during forward inference of AVO or other elastic wave field. But most of the recent conventional log data is lack of shear wave. Thus according to the research on petrophysical model, the rock S-wave parameter can be evaluated from conventional log data with probability inverse method. ③ AVO forward modeling based on well data For 6 wells in JZ31-6 block and 9 wells in LD22-1 block, the AVO forward modeling recording is made by log curve. The classification of AVO characteristics in objective interval is made by the lithologic information. ④ The 2D parameter model building and forward modeling of subtle hydrocarbon trap in target area. According to the formation interpretation of ESS03D seismic area, the 2D parameter model building and seismic wave field forward modeling are carried on the given and predicted subtle hydrocarbon trap with log curve. ⑤ The lithology and fluid identification of subtle trap in target area After study the seismic response characteristics of lithology and fluid in given target area, the optimization of geophysical technique is used for lithology identification and fluid forecast. ⑥The geophysical identification technique system of subtle reservoir The Innovative Points of this Paper ① Based on laboratory measurement and petrophysical model theory, the rock S-wave parameter can be evaluated from conventional log data with probability inverse method. Then the fluid substitution method based on B-G and K-T theory is provided. ② The method and workflow for simulating seismic wave field property of subtle hydrocarbon trap are established based on the petrophysical model building and forward modeling of wave equation. ③ The description of subtle trap structural feature is launched. According to the different reflection of frequency wave field structural attribute, the fluid property of subtle trap can be identified by wave field attenuation attribute and absorption analysis. ④ It’s the first time to identify subtle trap by geophysical technique and provide exploration drilling well location. ⑤ The technique system of subtle reservoir geophysical identification is formed to provide available workflow and research ideas for other region of interest.

渤海海域河流相油藏精细描述技术及应用研究

Aiming at the character of Bohaii Sea area and the heterogeneity of fluvial facies reservoir, litho-geophysics experiments and integrated research of geophysical technologies are carried out. To deal with practical problems in oil fields of Bohai area, such as QHD32-6, Southern BZ25-1 and NP35-2 et al., technology of reservoir description based on seismic data and reservoir geophysical methods is built. In this dissertation, three points are emphasized: ①the integration of multidiscipline; ②the application of new methods and technologies; ③the integration of quiescent and dynamic data. At last, research of geology modeling and reservoir numerical simulation based on geophysical data are integrated. There are several innovative results and conclusion in this dissertation: (1)To deal with problems in shallow sea area where seismic data is the key data, a set of technologies for fine reservoir description based on seismic data in Bohai Sea area are built. All these technologies, including technologies of stratigraphic classification, sedimentary facies identification, structure fine characterization, reservoir description, fluid recognition and integration of geological modeling& reservoir numerical simulation, play an important role in the hydrocarbon exploration and development. In the research of lithology and hydrocarbon-bearing condition, petrophysical experiment is carried out. Outdoors inspection and experiment test data are integrated in seismic forward modeling& inversion research. Through the research, the seismic reflection rules of fluid in porosity are generated. Based on all the above research, seismic data is used to classify rock association, identify sedimentary facies belts and recognition hydrocarbon-bearing condition of reservoir. In this research, the geological meaning of geophysical information is more clear and the ambiguity of geophysical information is efficiently reduced, so the reliability in hydrocarbon forecasting is improved. The methods of multi-scales are developed in microfacies research aiming at the condition of shallow sea area in Bohai Sea: ① make the transformation from seismic information to sedimentary facies reality by discriminant analysis; ②in research of planar sedimentary facies, make microfacies research on seismic scale by technologies integration of seismic multi-attributes analysis& optimization, strata slicing and seismic waveform classification; ③descript the sedimentary facies distribution on scales below seismic resolution with the method of stochastic modeling. In the research of geological modeling and reservoir numerical simulation, the way of bilateral iteration between modeling and numerical simulation is carried out in the geological model correction. This process include several steps: ①make seismic forward modeling based on the reservoir numerical simulation results and geological models; ②get trend residual of forward modeling and real seismic data; ③make dynamic correction of the model according to the above trend residual. The modern integration technology of reservoir fine description research in Bohai Sea area, which is developed in this dissertation, is successfully used in (1)the reserve volume evaluation and development research in BZ25-1 oil field and (2)the tracing while drilling research in QHD32-6 oil field. These application researches show wide application potential in hydrocarbon exploration and development research in other oil fields.

叠前叠后联合反演技术及其在QHD32-6油田的应用研究

What geophysical inversion studied includes the common mathematics physical property of inversion and the constitution and appraisal method of solution in geophysics domain, i.e. using observed physical phenomenon from the earth surface to infer space changing and physical property structure of medium within the earth. Seismic inversion is a branch of geophysical inversion. The basic purpose of seismic inversion is to utilizing seismic wave propagating law in the medium underground to infer stratum structure and space distribution of physical property according to data acquisition, processing and interpretation, and then offer the vital foundation for exploratory development. Poststack inversion is convenient and swift, its acoustic impedance inversion product can reflect reservoir interior changing rule to a certain degree, but poststack data lack abundant amplitude and travel time information included in prestack data because of multiple superimpose and weaken the sensitiveness which reflecting reservoir property. Compared with poststack seismic inversion, prestack seismic inversion has better fidelity and more adequate information. Prestack seismic inversion, including waveform inversion, not only suitable for thin strata physical property inversion, it can also inverse reservoir oil-bearing ability. Prestack seismic inversion and prestack elastic impedance inversion maintain avo information, sufficiently applying seismic gathering data with different incident angle, partial angle stack, gradient and intercept seismic data cube. Prestack inversion and poststack inversion technology were studied in this dissertation. A joint inversion method which synthesize prestack elastic wave waveform inversion, prestack elastic impedance inversion and poststack inversion was proposed by making fully use of prestack inversion multiple information and relatively fast and steady characteristic of poststack inversion. Using the proposed method to extract rock physics attribute cube with clear physical significance and reflecting reservoir characterization, such as P-wave and S-wave impedance, P-wave and S-wave velocity, velocity ratio, density, Poisson ratio and Lame’s constant. Regarding loose sand reservoir in lower member of Minghuazhen formation, 32-6 south districts in Qinhuangdao,as the research object, be aimed at the different between shallow layer loose sand and deep layer tight sand, first of all, acquire physical property parameters suitable for this kind of heavy oil pool according to experimental study, establishing initial pressure and shear wave relational model; Afterwards, performing prestack elastic wave forward and inversion research, summarizing rules under the guidance of theoretical research and numerical simulation, performing elastic impedance inversion, calculating rock physics attributes; Finally, predicting sand body distribution according to rock physics parameters, and predicting favorable oil area combine well-logging materials and made good results.

松辽盆地长岭断陷火山岩储层识别与勘探目标评价

Changling fault depression is the biggest fault subsidence in south of Songliao Basin. In its Lower Cretaceous Yingcheng and Shahezi formations developed thick source rocks of deep lake facies and developed poly-phase volcanic rock reservoirs as well. In recent years, significant breakthroughs have been obtained in hydrocarbon exploration of volcanic rock reservoir in the different fault depressions in Songliao basin. Lately, I have been involved in hydrocarbon exploration in the Changling rift depression, especially volcanic rock reservoirs and exploration targets research, participating in the deployment of well Yaoshen 1 which gained over 40 × 104m3 natural gas flow. As quick changes of lithology and facies in Changling area in the south of Songliao basin, and the volcanic rock interludes distribution in continental clastic rock and shale in 3D space, so the identification of volcanic rock types and distribution become a difficult problem. Thus, based on the integrated research of the wild outcrop observation, gravity, magnetic and seismic data, geophysical logging, drilling and coring, laboratory test, this paper carried out the reservoir identification, description and prediction of volcanic rocks in Changling fault depression. In this area, this paper analyzed the volcanic rocks litho-facies, the eruption period, and characteristics of cycles. At the same time, tried to know how to use logging, seismic data to separate volcanic rocks from sandstone and shale, distinguish between volcanic reservoir and non-reservoir, distinguish between intermediate-basic and acidic volcanic rocks, and how to identify traps of volcanic rocks and its gas-bearing properties, etc. Also it is summarized forming conditions and distribution of traps, and possible gas-bearing traps were optimized queuing management. Conclusions as follows: There are two faulted basements in Changling fault depression, granite basement in the southeast and upper paleozoic epimetamorphic basement in the northwest. The main volcanic reservoirs developed in Yingcheng period, which was the intermediate-basic and acidic volcanic eruptions, from the south to north by the intermediate-basic to acid conversion. The volcanic vents are gradually young from south to north. According to information of the re-processing 3D seismic data and gravity-magnetic data, the large volcanic vent or conduit was mainly beaded-distributed along the main fault. The volcanic rocks thickness in Yingcheng formation was changed by the deep faults and basement boundary line. Compared with the clastic rocks, volcanic rocks in Changling area are with high resistance and velocity (4900-5800), abnormal Gamma. All kinds of volcanic rocks are with abnormal strong amplitude reflection on the seismic stacked section except tuff. By analyzing the seismic facies characteristics of volcanic rocks, optimizing seismic attributes constrained by logging, using seismic amplitude and waveforms and other attributes divided volcanic rocks of Yingcheng formation into four seismic zones in map. Currently, most volcanic gas reservoirs are fault-anticline and fault-nose structure. But the volcanic dome lithologic gas reservoirs with large quantity and size are the main gas reservoir types to be found.

青岛晚白垩世岩石圈结构特征：劈石口晚白垩世基性脉岩及其捕虏体提供的证据

The occurrence of Late Cretaceous mafic dykes and their entrained peridotite and granulite xenoliths as well as clinopyroxene xenocrysts in the Qingdao region provide us a precious opportunity to unveil the nature and characteristics of the Late Mesozoic lithospheric mantle and lower crust beneath the Jiaodong region, and the change of the magma sources. These studies are of important and significant for understanding the lithospheric evolution in the eastern North China Craton. There were two periods of magma activities in Late Mesozoic in Qingdao Laoshan region, one was around 107Ma in the Early Cretaceous and the other around 86Ma in the Late Cretaceous according to the whole rock K-Ar age determination. The Early Cretaceous mafic dykes and the Late Cretaceous mafic dyke (i.e. Pishikou mafic dike) have completely different geochemical characteristics. The Early Cretaceous mafic dykes are enriched in LILE, strongly depleted in HFSE (Nb, Ta, Zr, Hf) and characterized by the highly radiogenic Sr and Nd isotopic compositions. These geochemical features indicate that the Early Cretaceous mafic dykes were derived from an enriched lithospheric mantle. In contrast, the Late Cretaceous mafic dyke is enriched in LILE, without HFSE depletion (Nb, Ta, Zr, Hf) and has less radiogenic Nd and Sr isotopic compositions. These geochemical features indicate that the Late Cretaceous mafic dyke was derived from the asthenosphere modified by subducted pelagic sediment contamination. The intrusive age of the Late Cretaceous mafic dyke provides further information for the termination of the lithosphere thinning for the eastern North China Crtaon. Pishikou Late Cretaceous mafic dyke contains abundant peridotitic xenoliths, granulite xenoliths and clinopyroxene xenocrysts. The peridotitic xenoliths can be divided into two types: high Mg# peridotites and low Mg# peridotites, according to their textural and mineral features. The high-Mg# peridotites have high Fo (up to 92.2) olivines and high Cr# (up to 55) spinels. The clinopyroxenes in the high# peridotites are rich in Cr2O3 and poor in Al2O3. The low-Mg# peridotites are typified by low Mg# (Fo <90) in olivines and low Cr# (Cr# <0.14) in spinels. The clinopyroxenes in the low-Mg# peridotites are rich in Al2O3 and Na2O and poor in Cr2O3. These two type peridotites have similar equilibrated temperatures of 950C-1100C. The Clinopyroxenes in the high-Mg# peridotites generally have high and variable REE contents (REE = 5.6-84 ppm) and LREE-enriched chondrite-normalized patterns ((La/Yb)N>1). In contrast, the clinopyroxenes in the low-Mg# peridotites have low REE contents (REE = 12 ppm) and LREE-depleted patterns ((La/Yb)N<1). The textural, mineral and elemental features of the low-Mg# peridotites are similar to those of the low-Mg peridotites from the Junan, representing the newly-accreted lithospheric mantle. However, the mineralogical and petrological features of the high-Mg# peridotites are similar to those of the high-Mg# peridotites from the Junan region, representing samples from the old refractory lithospheric mantle that was strongly and multiply affected by melts of different origins Late Cretaceous mafic dike in the Qingdao region also contains two types of granulite xenoliths according to the mineral constituents: the pyroxene-rich granulites and the plagioclase-rich granulites. Equilibrated temperatures calculated from the cpx-opx geothermometers are in a range of 861C - 910C for the pyroxene-rich granulites and of 847C - 890C for the plagioclase-rich granulites. The equilibrated pressure for the plagioclase-rich granulites is in a range of 9.9-11.7 kbar. Combined with the results of the peridotitic xenoliths, a 40C temperature gap exists between the peridotite and the granulite. The petrological Moho was 33~36 km at depths, broadly consistent with the seismic Moho estimated from the geophysical data. This indicates that there was no obvious crust-mantle transition zone in the Qingdao region in the Late Mesozoic. Pishikou Late Cretaceous mafic dyke entrained lots of clinopyroxene xenocrysts which are characterized by the chemical zoning. According to the zoning features, two types of clinopyroxene xenoliths can be classified, the normal zoning and the revise zoning. The normally-zoned clinopyroxene xenocrysts have LREE-depleted REE patterns in the cores. In contrast, the revisely-zoned clinopyroxenes have LREE-enriched REE patterns in the cores. According to the rim and core compositions of xenocrysts, all the rims are balanced with the host magma. Meanwhile, the origins of the cores were complicated, in which the normally-zoned clinopyroxenes were derived form the lithospheric mantle and some of the reversely-zoned clinopyroxnes were originated from the lower crust. Other revisely-zoned clinopyroxenes had experienced complex geological evolution and need to be further investigated. According to the above results, a simplified lithospheric profile has been established beneath the Qingdao region and a constraint on the nature and characteristics of the lithospheric mantle and lower crust has been made.

青藏高原及邻区面波频散反演--岩石圈-软流层体系结构研究

The Qinghai-Tibet Plateau lies in the place of the continent-continent collision between Indian and Eurasian plates. Because of their interaction the shallow and deep structures are very complicated. The force system forming the tectonic patterns and driving tectonic movements is effected together by the deep part of the lithosphere and the asthenosphere. It is important to study the 3-D velocity structures, the spheres and layers structures, material properties and states of the lithosphere and the asthenosphere for getting knowledge of their formation and evolution, dynamic process, layers coupling and exchange of material and energy. Based on the Rayleigh wave dispersion theory, we study the 3-D velocity structures, the depths of interfaces and thicknesses of different layers, including the crust, the lithosphere and the asthenosphere, the lithosphere-asthenosphere system in the Qinghai-Tibet Plateau and its adjacent areas. The following tasks include: (1)The digital seismic records of 221 seismic events have been collected, whose magnitudes are larger than 5.0 over the Qinghai-Tibet Plateau and its adjacent areas. These records come from 31 digital seismic stations of GSN , CDSN、NCDSN and part of Indian stations. After making instrument response calibration and filtering, group velocities of fundamental mode of Rayleigh waves are measured using the frequency-time analysis (FTAN) to get the observed dispersions. Furthermore, we strike cluster average for those similar ray paths. Finally, 819 dispersion curves (8-150s) are ready for dispersion inversion. (2)From these dispersion curves, pure dispersion data in 2°×2° cells of the areas (18°N-42°N, 70°E-106°E) are calculated by using function expansion method, proposed by Yanovskaya. The average initial model has been constructed by taking account of global AK135 model along with geodetic, geological, geophysical, receiving function and wide-angle reflection data. Then, initial S-wave velocity structures of the crust and upper mantle in the research areas have been obtained by using linear inversion (SVD) method. (3)Taking the results of the linear inversion as the initial model, we simultaneously invert the S wave velocities and thicknesses by using non-linear inversion (improved Simulated Annealing algorithm). Moreover, during the temperature dropping the variable-scale models are used. Comparing with the linear results, the spheres and layers by the non-linear inversion can be recognized better from the velocity value and offset. (4)The Moho discontinuity and top interface of the asthenosphere are recognized from the velocity value and offset of the layers. The thicknesses of the crust, lithosphere and asthenosphere are gained. These thicknesses are helpful to studying the structural differentia between the Qinghai-Tibet Plateau and its adjacent areas and among geologic units of the plateau. The results of the inversion will provide deep geophysical evidences for studying deep dynamical mechanism and exploring metal mineral resource and oil and gas resources. The following conclusions are reached by the distributions of the S wave velocities and thicknesses of the crust, lithosphere and asthenosphere, combining with previous researches. (1)The crust is very thick in the Qinghai-Tibet Plateau, varying from 60 km to 80 km. The lithospheric thickness in the Qinghai-Tibet Plateau is thinner (130-160 km) than its adjacent areas. Its asthenosphere is relatively thicker, varies from 150 km to 230 km, and the thickest area lies in the western Qiangtang. India located in south of Main Boundary thrust has a thinner crust (32-38 km), a thicker lithosphere of about 190 km and a rather thin asthenosphere of only 60 km. Sichuan and Tarim basins have the crust thickness less than 50km. Their lithospheres are thicker than the Qinghai-Tibet Plateau, and their asthenospheres are thinner. (2)The S-wave velocity variation pattern in the lithosphere-asthenosphere system has band-belted distribution along east-westward. These variations correlate with geology structures sketched by sutures and major faults. These sutures include Main Boundary thrust (MBT), Yarlung-Zangbo River suture (YZS), Bangong Lake-Nujiang suture (BNS), Jinshajiang suture (JSJS), Kunlun edge suture (KL). In the velocity maps of the upper and middle crust, these sutures can be sketched. In velocity maps of 250-300 km depth, MBT, BNS and JSJS can be sketched. In maps of the crustal thickness, the lithospheric thickness and the asthenospheric thickness, these sutures can be still sketched. In particular, MBT can be obviously resolved in these velocity maps and thickness maps. (3)Since the collision between India and Eurasian plate, the “loss” of surface material arising from crustal shortening is caused not only by crustal thickening but also by lateral extrusion material. The source of lateral extrusion lies in the Qiangtang block. These materials extrude along the JSJS and BNS with both rotation and dispersion in Daguaiwan. Finally, it extends toward southeast direction. (4)There is the crust-mantle transition zone of no distinct velocity jump in the lithosphere beneath the Qiangtang Terrane. It has thinner lithosphere and developed thicker asthenosphere. It implies that the crust-mantle transition zone of partial melting is connected with the developed asthenosphere. The underplating of asthenosphere may thin the lithosphere. This buoyancy might be the main mechanism and deep dynamics of the uplift of the Qinghai-Tibet hinterland. At the same time, the transport of hot material with low velocity intrudes into the upper mantle and the lower crust along cracks and faults forming the crust-mantle transition zone.

整合多尺度地球物理数据建立高分辨率储层模型的方法及应用

Most of the fields in China are in the middle-late development phase or are mature fields. It becomes more and more difficult to develop the remaining oil/gas. Therefore, it is import to enhance oil/gas recovery in order to maintain the production. Fine scale modeling is a key to improve the recovery. Incorporation of geological, seismic and well log data to 3D earth modeling is essential to build such models. In Ken71 field, well log, cross-well seismic and 3D seismic data are available. A key issue is to build 3D earth model with these multi-scales data for oil field development.In this dissertation, studies on sequential Gaussian-Bayesian simulation have been conducted. Its comparison with cokriging and sequential Gaussian simulation has been performed. The realizations generated by sequential Gaussian-Bayesian simulation have higher vertical resolution than those generated by other methods. Less differences between these realization and true case are observed. With field data, it is proved that incorporating well log, cross-well seismic and 3D seismic into 3D fine scale model is reliable. In addition, the advantages of sequential Gaussian-Bayesian simulation and conditions for input data are demonstrated. In Ken71 field, the impedance difference between sandstone and shale is small. It would be difficult to identify sandstone in the reservoir with traditional impedance inversion. After comparisons of different inversion techniques, stochastic hillclimbing inversion was applied. With this method, shale content inversion is performed using 3D seismic data. Then, the inverted results of shale content and well log data are incorporated into 3D models. This demonstrates a procedure to build fine scale models using multi scale seismic data, especially 3D seismic amplitude volume.The models generated through sequential Gaussian-Bayesian simulation have several advantages including: (1) higher vertical resolution compared with 3D inverted acoustic impedance (AI); (2) consistency of lateral variation as 3D inverted AI; (3) more reliability due to integration cross-well seismic data. It is observed that the precision of the model depends on the 3D inversion.

青藏高原横波速度与各向异性结构及其壳幔形变印迹

As the most spectacular and youngest case of continental collision on the Earth, to investigate the crust and mantle of Tibetan plateau, and then to reveal its characters of structure and deformation, are most important to understand its deformation mechanism and deep process. A great number of surface wave data were initially collected from events occurred between 1980 and 2002, which were recorded by 13 broadband digital stations in Eurasia and India. Up to 1,525 source-station Rayleigh waveforms and 1,464 Love wave trains were analysed to obtain group velocity dispersions, accompanying with the detail and quantitative assessment of the fitness of the classic Ray Theory, errors from focal and measurements. Assuming the model region covered by a mesh of 2ox2o-sized grid-cells, we have used the damped least-squares approach and the SVD to carry out tomographic inversion, SV- and SH-wave velocity images of the crust and upper mantle beneath the Tibetan Plateau and surroundings are obtained, and then the radial anisotropy is computed from the Love-Rayleigh discrepancy. The main results demonstrate that follows, a) The Moho beneath the Tibetan Plateau presents an undulating shape that lies between 65 and 74 km, and a clear correlation between the elevations of the plateau and the Moho topography suggests that at least a great part of the highly raised plateau is isostatically compensated. b) The lithospheric root presents a depth that can be substantiated at ~140 km (Qiangtang Block) and exceptionally at ~180 km (Lhasa Block), and exhibits laterally varying fast velocity between 4.6 and 4.7 km/s, even ~4.8 km/s under northern Lhasa Block and Qiangtang Block, which may be correlated with the presence of a shield-like upper mantle beneath the Tibetan Plateau and therefore looked as one of the geophysical tests confirming the underthrusting of India, whose leading edge might have exceeded the Bangong-Nujiang Suture, even the Jinsha Suture. c) The asthenosphere is depicted by a low velocity channel at depths between 140 and 220 km with negative velocity gradient and velocities as low as 4.2 km/s; d) Areas in which transverse radial anisotropy is in excess of ~4% and 6% on the average anisotropy are found in the crust and upper mantle underlying most of the Plateau, and up to 8% in some places. The strength, spatial configuration and sign of radial anisotropy seem to indicate the existence of a regime of horizontal compressive forces in the frame of the convergent orogen at the same time that laterally varying lithospheric rheology and a differential movement as regards the compressive driving forces. e) Slow-velocity anomalies of 12% or more in southern Tibet and the eastern edge of the Plateau support the idea of a mechanically weak middle-to-lower crust and the existence of crustal flow in Tibet.

地震数据波动方程反演方法研究

Geophysical inversion is a theory that transforms the observation data into corresponding geophysical models. The goal of seismic inversion is not only wave velocity models, but also the fine structures and dynamic process of interior of the earth, expanding to more parameters such as density, aeolotropism, viscosity and so on. As is known to all, Inversion theory is divided to linear and non-linear inversion theories. In rencent 40 years linear inversion theory has formed into a complete and systematic theory and found extensive applications in practice. While there are still many urgent problems to be solved in non-linear inversion theory and practice. Based on wave equation, this dissertation has been mainly involved in the theoretical research of several non-linear inversion methods: waveform inversion, traveltime inversion and the joint inversion about two methods. The objective of gradient waveform inversion is to find a geologic model, thus synthetic seismograms generated by this geologic model are best fitted to observed seismograms. Contrasting with other inverse methods, waveform inversion uses all characteristics of waveform and has high resolution capacity. But waveform inversion is an interface by interface method. An artificial parameter limit should be provided in each inversion iteration. In addition, waveform information will tend to get stuck in local minima if the starting model is too far from the actual model. Based on velocity scanning in traditional seismic data processing, a layer-by-layer waveform inversion method is developed in this dissertation to deal with weaknesses of waveform inversion. Wave equation is used to calculate the traveltime and derivative (perturbation of traveltime with respect to velocity) in wave-equation traveltime inversion (WT). Unlike traditional ray-based travetime inversion, WT has many advantages. No ray tracing or traveltime picking and no high frequency assumption is necessary and good result can be got while starting model is far from real model. But, comparing with waveform inversion, WT has low resolution. Waveform inversion and WT have complementary advantages and similar algorithm, which proves that the joint inversion is a better inversion method. And another key point which this dissertation emphasizes is how to give fullest play to their complementary advantages on the premise of no increase of storage spaces and amount of calculation. Numerical tests are implemented to prove the feasibility of inversion methods mentioned above in this dissertation. Especially for gradient waveform inversion, field data are inversed. This field data are acquired by our group in Wali park and Shunyi district. Real data processing shows there are many problems for waveform inversion to deal with real data. The matching of synthetic seismograms with observed seismograms and noise cancellation are two primary problems. In conclusion, on the foundation of the former experiences, this dissertation has implemented waveform inversions on the basis of acoustic wave equation and elastic wave equation, traveltime inversion on the basis of acoustic wave equation and traditional combined waveform traveltime inversion. Besides the traditional analysis of inversion theory, there are two innovations: layer by layer inversion of seimic reflection data inversion and rapid method for acoustic wave-equation joint inversion.

Pg震相走时的各向异性影响及各向异性结构成像

As the first arrival of seismic phase in deep seismic sounding, Pg is the important data for studying the attributes of the sedimentary layers and the shape of crystalline basement because of its high intensity and reliable detection. Conventionally, the sedimentary cover is expressed as isotropic, linear increasing model in the interpretation of Pg event. Actually, the sedimentary medium should be anisotropic as preferred cracks or fractures and thin layers are common features in the upper crust, so the interpretation of Pg event needs to be taken account of seismic velocity anisotropy. Traveltime calculation is the base of data processing and interpretation. Here, we only study the type of elliptical anisotropy for the poor quality and insufficiency of DSS data. In this thesis, we first investigate the meaning of elliptical anisotropy in the study of crustal structure and attribute, then derive Pg event’s traveltime-offset relationship by assuming a linear increasing velocity model with elliptical anisotropy and present the invert scheme from Pg traveltime-offset dataset to seismic velocity and its anisotropy of shallow crustal structure. We compare the Pg traveltime calculated by our analytic formula with numerical calculating method to test the accuracy. To get the lateral variation of elliptical anisotropy along the profiling, a tomography inversion method with the derived formula is presented, where the profile is divided into rectangles. Anisotropic imaging of crustal structure and attribute is efficient method for crust study. The imaging result can help us interprete the seismic data and discover the attribute of the rock to analyze the interaction between layers. Traveltime calculation is the base of image. Base on the ray tracing equations, the paper present a realization of three dimension of layer model with arbitrary anisotropic type and an example of Pg traveltime calculation in arbitrary anisotropic type is presented. The traveltime calculation method is complex and it only adapts to nonlinear inversion. Perturbation method of travel-time calculation in anisotropy is the linearization approach. It establishes the direct relation between seismic parameters and travetime and it is fit for inversion in anisotropic structural imaging. The thesis presents a P-wave imaging method of layer media for TTI. Southeastern China is an important part of the tectonic framework concerning the continental margin of eastern China and is commonly assumed to comprise the Yangtze block and the Cathaysia block, the two major tectonic units in the region. It’s a typical geological and geophysical zone. In this part, we fit the traveltime of Pg phase by the raytracing numerical method. But the method is not suitable here because the inefficiency of numerical method and the method itself. By the analytic method, we fit the Pg and Sg and get the lateral variation of elliptical anisotropy and then discuss its implication. The northeastern margin of Qinghai-Tibetan plateau is typical because it is the joint area of Eurasian plate and Indian plate and many strong earthquakes have occurred there in recent years．We use the Pg data to get elliptical anisotropic variation and discuss the possible meaning.

天然气藏地震识别技术研究

The Research of Seismic Recognition Techniques for Gas Reservoir Shang Yong_sheng(Geophysics) Directed by Yang Chang-chun Abstract Gas reservior is one of the most important nature resources. Someone forecast that the output will exceed crude oil in 2015 and become the largest energy source. Recently,more and more gas reservior are discovered as the oil field and gas filed exploration go deep into development. Although the gas proved reserves rise greatly the explorative degree of natural gas resource in our country is still very low. The potential of gas exploration is very great and our task is so hard. How to recognise and discover new gas reservoir is the first task based on the great gas reservior resources foreground. the gas reservior in different oil and gas field have its special gas generation, reservoiring, physical property conditions. However,it may have the same geophysical characters. So,it is very important to analyse, research, summarizing the geophysical characters of the gas reservior and make use of the characters to identify the gas layer effectively. This paper start with modeling,and it discuss the geophysical characters of the gas reservior response. It analyse the seismical wave characters of the gas reservoir. Furthermore, it summarize the method of using the seismica profile to identify the gas reservior directly. The paper discuss the research of extracting diffraction wave for mass diffraction wave grow at the edge of the gas reservoir at the seismic section. Making use of the technique of extracting diffraction wave to identify the gas reservior is the first experiment of the gas reservoir prediction technique. The avo technology is a new geophysical method. From the pre-stack analysis, this paper discuss the technique of using the rich information to identify the gas reservoir. Based on the case study of the Qidam basin and the Hailaer basin it discuss the method of predicating gas reservoir using pre-stack information. It include pre-stack amplitude preserve process, AVO modeling, fluid replacement technique, AVO analysis and interpretation technique. The paper summarize a gas reservoir prediction procedure focusing on the pre-stack information. The seismic wave will cause great attenuation when it pass through the gas layer and the high frequency component loss. This paper discuss the technique of extracting seismic attributes to represent the attenuation degree of seismica wave. Based on the attenuation attributes,it does the research of the gas reservor identification and prediction. At last,the paper discuss the method of calculating the azimuthal anisotropy to predict the fracture reservoir. Keyword: gas reservoir, diffraction wave, AVO, attenuation attribute,fracture prediction

济阳坳陷深层地质构造与演化

Based on geophysical and geological data in Jiyang depression, the paper has identified main unconformity surfaces (main movement surfaces) and tectonic sequences and established tectonic and strata framework for correlation between different sags. Based on different sorts of structural styles and characteristics of typical structures, the paper summarized characteristics and distribution of deep structures, discussed evolution sequence of structure, analyzed the relation between tectonic evolution and generation of petroleum. The major developments are as following: Six tectonic sequences could be divided from bottom to top in the deep zone of Jiyang depression. These tectonic sequences are Cambrian to Ordovician, Carboniferous to Permian, lower to middle Jurassic, upper Jurassic to lower Cretaceous, upper Cretaceous and Kongdian formation to the fourth member of Shahejie formation. The center of sedimentation and subsidence of tectonic sequences distinguished from each other in seismic profiles is controlled by tectonic movements. Six tectonic evolution stages could be summarized in the deep zone in Jiyang depression. Among these stages, Paleozoic stage is croton sedimentation basin; Indosinian stage, open folds of EW direction are controlled by compression of nearly SN direction in early Indosinian (early to middle Triassic) while fold thrust fault of EW – NWW direction and arch protruding to NNE direction are controlled by strong compression in late Indosinian (latter Triassic); early Yanshanian stage (early to middle Jurassic), in relatively weak movement after Indosinian compressional orogeny, fluviolacustrine is deposited in intermontane basins in the beginning of early Yanshanian and then extensively denudated in the main orogenic phase; middle Yanshanian (late Jurassic to early Cretaceous), strike-slipping basins are wide distribution with extension (negative reversion) of NW – SE direction; latter Yanshanian (late Cretaceous), fold and thrust of NE – NNE direction and positive reversion structure of late Jurassic to early Cretaceous strike-slipping basin are formed by strong compression of NW–SE direction; sedimentation stage of Kongdian formation to the fourth member of Shahejie formation of Cenozoic, half graben basins are formed by extension of SN direction early while uplift is resulted from compression of nearly EW direction latterly. Compression system, extension system and strike-slip system are formed in deep zone of Jiyang depression. According to identifying flower structure of seismic profiles and analysis of leveling layer slice of 3D seismic data and tectonic map of deep tectonic interface, strike-slip structures of deep zone in Jiyang depression are distinguished. In the middle of the Jiyang depression, strike-slip structures extend as SN direction, NNW direction in Huimin sag, but NNE in Zhandong area. Based on map of relict strata thickness, main faults activity and regional tectonic setting, dynamic mechanisms of deep structure are preliminary determination. The main reason is the difference of direction and character of the plate’s movement. Development and rework of multi-stage tectonic effects are benefit for favorable reservoir and structural trap. Based on tectonic development, accumulation conditions of deep sub-sags and exploration achievements in recent years, potential zones of oil-gas reservoir are put forward, such as Dongying sag and Bonan sag.

残留盆地分布综合地球物理研究——以大港地区为例

Macro-distribution of residual basins is a basic question in residual basin research，the main object of macro-distribution study is to build strata framework, compute thickness of residual strata and analyze characteristics of residual basins. With the guidance of the theory of integrated geology and geophysical research, the paper assembled series of methods and established the technical chart based on gravity and magnetic data, with restriction of geology, seismic and drilling data. Based on potential field data processing and analysis, forward and inverse computation, region potential field analysis and potential field separation, etc. it computed depth of gravity/magnetic basement and got strata framework. It had got effective results in the research of macro-distribution of residual basin research in the Dagang area. It did the wavelet transform of gravity/magnetic data with multi-kind of wavelet basis using a trou algorithm. From comparison of processing result and their spectral of wavelet analysis, up continuation and filter method, the wavelet approximation is better to fit the regional potential field, and it is an effective method to separate gravity/magnetic effect caused by deep geology bodies. The experiment of matching pursuit shows that te transform domain methods have great advantage in potential data analysis. From the integrated geophysical study of rock property study, gravity/magnetic basement inversion and fault system analysis of the Dagang area, it gets the strata framework and the thickness of pre-Cenozoic residual strata. Comprehensive study with gravity and magnetotelluric profile inversion and interpretation, three prospect plays of macro-distribution of residual basins are fingered out. It has great residual strata thickness in the northern part of Chengning Uplift and there is thrust fault in the deep zone and good up-Paleozoic hydrocarbon source rocks in this area. With integrated analysis, this area will be the most prospective hydrocarbon location of pre-Cenozoic residual basins.

中低纬度变化磁场的暴时特征研究

Magnetic storm is a kind of severe disturbances in the whole solar-earth electromagnetic space. It has significant effects on communication, electric power, oil transport pipe and human activities in space. Therefore, magnetic storms are worth for applications systems, not only being a favorable issue for scientists. In this paper, the spatial and temporal distributions of the magnetic fields produced by the magnetosphere-ionosphere current systems during storms are studied. Four parts are included in this paper decomposion of different disturbances with different origins, topological structure of the ring current, the asymmetric characteristics of the ring current, and the statistic peculiarities of the day-to-day variability (DTD) of Sq. 1 The decomposition of magnetic disturbances at mid-low latitudes and its evolutions during storms Transient variations in the geomagnetic field recorded at mid-low latitudes mainly include the storm-time variation (Dst), solar quiet daily variation (Sq) and disturbance daily variation (SD). With the data of the geomagnetic meridian chain observatories in China, 25 storms during the period of 1997 to 1999 have been analyzed. According to the features of different variations, a method of “three-steps decomposition” is developed by using the method of Natural Orthogonal Components (NOC), Correlation Analysis and Fourier Analysis to separate those three components in turn. The results show that, the first eigenmode by the MNOC clearly describing the special distribution and temporal evolution of storm-time variation, in addition, Correlation Analysis and Fourier Analysis offer a useful method to extract the Sq and SD variations. The latitudinal shift of the Sq current focus seems to be the principal reason of the day-to-day variaitons in the daily range of Sq. The magnitude of SD reaches a maximum during the main phase, and then gradually decreases. 2 The topology structure of the ring current during storms Both the mechanism of the ring current and the geomagnetic data suggest that the central plane of the ring current is declining to the geomagnetic equator plane with a tilt angle δ. Using the H and Z component data at two stations in a meridian chain, we deduce a new parameter describing the invariable peculiarity of different storms. Then the δ angle is calculated by using the data from a meridian chain and tested with the ERC model. Finally the deduced tilt angles are used to modify Dst index. 3 The asymmetric characteristics of the ring current during storms The variations of the geomagnetic field at mid-low latitudes show a significant dawn-dusk asymmetry, resulting from the superposition of the fields from the symmetric ring current and the partial ring current. On the basis of the data from the 20°E, 30°E meridian chains and 30°N latitudinal chain, the dawn-dusk asymmetry is investigated by using three methods, namely, statistic analysis, ring current model calculation and typical event analysis. This characteristic implies the asymmetry of the spatial distribution of the ring current. In addition, during the main phase after the sudden commencement (SC), H field increases and reaches maximum around noontime, implying the effect of the Chapman-Ferraro current. 4 The statistic characteristics of the day-to-day variability and its mechanism The day-to-day variability of the geomagnetic Sq field is studied by using the magnetic data from a meridian chain of magnetometers along 120° E longitude. The method of NOC is applied to separate the Sq variation from complicated disturbances. The first eigenmode with the largest eigenvalue represents fairly well the Sq variation with a conspicuous day-to-day variability in the daily range. For the stations on the same north- or south-side of the Sq current system focus, the day-to-day variations show a positive correlation. In contrast, for the stations on the different sides of the Sq focus, they show a negative correlation, suggesting an important role of latitudinal shift of the Sq current system focus to the day-to-day variability of the Sq daily range. The Sq daily range is correlated with the magnetic indices Ap and Dst in a peculiar way: on some severe disturbed days, noticeably enhancements of the Sq are observed, implying increases of the ionospheric conductivities and/or tidal wind velocities; on other severe disturbed days, however, dramatically reduced Sq variations occur, suggesting dominant effects of the ‘disturbance dynamo’ process.

大陆地壳岩石结构重建：方法与实例

The composition of the continental crust has long been a subject of interest to earth scientists as it can provide key information about the crustal growth and evolution of the continents. In this paper we make a comparative study on the lithological discrimination schemes featuring with the use of different seismic attributes, such as P-wave velocity, P- to S-wave velocity ratio, acoustic or elastic impedances, Lame impedances and high-sensitive identification factors. The results demonstrate that Lame impedances have more powerful constrains than other seismic attributes. In order to fully take the advantage of make the best of the different seismic response of crustal rock, we firstly use seismic attribute that have weak distinguish power to construct loose constrained lithological model, then use seismic attributes that have stronger distinguish power to tighten the constrains of lithological discrimination. We propose a joint scheme (chain constrain technique) by combing all available constrains to reduce the non-uniqueness in mapping rock distribution. We adopt chain constrain technique to construct lithological model beneath Tunxi-Wenzhou transect, Southeastern China, Manzhouli-Suifenhe transect, Northeastern China, and geophysical profile in Bohai Bay Basin, North China. The results can be suumarized as the follows: (1) We compare the sensitivity of different seismic factor constraints on rock types, and conclude that Lame impedances have tighter constrains than seismic velocity, Vp/Vs, density. (2) We propose chain constrains to construct lithological model from integrated geophysical data, and reduce the non-uniqueness in mapping rock distribution. (3) We reconstruct crustal lithological model beneath Tunxi-Wenzhou transect, Southeastern China. The results suggested that Jiangshan-Shaoxing fault is a crust-scale, and it is the boundary between Cathaysia and Yanthze blocks. (4) We construct crustal lithological model beneath Manzhouli-Suifenhe transect, Northeastern China. (5) We map the petrologic distribution along a geophysical profile in Bohai Bay Basin, North China, and construct a three-layered petrology model from the depth 2 km to about 10 km, consisted of basalt (the first layer), pelitic siltstone (the second layer), and silty mudstone and fine sandstone (the third layer).