Multifunctional cement composites strain and damage sensors applied on reinforced concrete (RC) structural elements

In this research, strain-sensing and damage-sensing functional properties of cement composites have been studied on a conventional reinforced concrete (RC) beam. Carbon nanofiber (CNFCC) and fiber (CFCC) cement composites were used as sensors on a 4 m long RC beam. Different casting conditions (in situ or attached), service location (under tension or compression) and electrical contacts (embedded or superficial) were compared. Both CNFCC and CFCC were suitable as strain sensors in reversible (elastic) sensing condition testing. CNFCC showed higher sensitivities (gage factor up to 191.8), while CFCC only reached gage factors values of 178.9 (tension) or 49.5 (compression). Furthermore, damage-sensing tests were run, increasing the applied load progressively up to the RC beam failure. In these conditions, CNFCC sensors were also strain sensitive, but no damage sensing mechanism was detected for the strain levels achieved during the tests. Hence, these cement composites could act as strain sensors, even for severe damaged structures near to their collapse.

An inverse method to obtain porosity, fibre diameter and density of fibrous sound absorbing materials

Characterization of sound absorbing materials is essential to predict its acoustic behaviour. The most commonly used models to do so consider the flow resistivity, porosity, and average fibre diameter as parameters to determine the acoustic impedance and sound absorbing coefficient. Besides direct experimental techniques, numerical approaches appear to be an alternative to estimate the material’s parameters. In this work an inverse numerical method to obtain some parameters of a fibrous material is presented. Using measurements of the normal incidence sound absorption coefficient and then using the model proposed by Voronina, subsequent application of basic minimization techniques allows one to obtain the porosity, average fibre diameter and density of a sound absorbing material. The numerical results agree fairly well with the experimental data.

Strain and damage sensing properties on multifunctional cement composites with CNF admixture

Both strain and damage sensing properties on carbon nanofiber cement composites (CNFCC) are reported in the present paper. Strain sensing tests were first made on the material’s elastic range. The applied loading levels have been previously calculated from mechanical strength tests. The effect of several variables on the strain-sensing function was studied, e.g. cement pastes curing age, current density, loading rate or maximum stress applied. All these parameters were discussed using the gage factor as reference. After this first set of elastic experiments, the same specimens were gradually loaded until material’s failure. At the same time both strain and resistivity were measured. The former was controlled using strain gages, and the latter using a multimeter on a four probe setup. The aim of these tests was to prove the sensitivity of these CNF composites to sense their own damage, i.e. check the possibility of fabricating structural damage sensors with CNFCC’s. All samples with different CNF dosages showed good strain-sensing capacities for curing periods of 28 days. Furthermore, a 2%CNF reinforced cement paste has been sensitive to its own structural damage.

Mechanical Properties and Durability of CNT Cement Composites

In the present paper, changes in mechanical properties of Portland cement-based mortars due to the addition of carbon nanotubes (CNT) and corrosion of embedded steel rebars in CNT cement pastes are reported. Bending strength, compression strength, porosity and density of mortars were determined and related to the CNT dosages. CNT cement paste specimens were exposed to carbonation and chloride attacks, and results on steel corrosion rate tests were related to CNT dosages. The increase in CNT content implies no significant variations of mechanical properties but higher steel corrosion intensities were observed.

Effect of aspect ratio on strain sensing capacity of carbon fiber reinforced cement composites

The electrical resistivity of carbon fiber reinforced cement composites (CFRCCs) has been widely studied, because of their utility as multifunctional materials. The percolation phenomenon has also been reported and modeled when the electrical behavior of those materials had to be characterized. Amongst the multiple applications of multifunctional cement composites the ability of a CFRCC to act as a strain sensor is attractive. This paper provides experimental data relating self-sensing function and percolation threshold, and studying the effect of fiber aspect ratio on both phenomena. Higher fiber slenderness permitted percolation at lower carbon fiber addition, affected mechanical properties and improved strain-sensing sensitivity of CFRCC, which was also improved if percolation had not been achieved.

Flexible ruthenium oxide-activated carbon cloth composites prepared by simple electrodeposition methods

This work focuses on the preparation of flexible ruthenium oxide containing activated carbon cloth by electrodeposition. Different electrodeposition methods have been used, including chronoamperometry, chronopotentiometry and cyclic voltammetry. The electrochemical properties of the obtained materials have been measured. The results show that the potentiostatic method allows preparing composites with higher specific capacitance than the pristine activated carbon cloth. The capacitance values measured by cyclic voltammetry at 10 mV s−1 and 1 V of potential window were up to 160 and 180 F g−1. This means an improvement of 82% and 100% with respect to the capacitance of the pristine activated carbon cloth. This excellent capacitance enhancement is attributed to the small particle size (4–5 nm) and the three-dimensional nanoporous network of the ruthenium oxide film which allows reaching very high degree of oxide utilization without blocking the pore structure of the activated carbon cloth. In addition, the electrodes maintain the mechanical properties of the carbon cloth and can be useful for flexible devices.

Production of nanoTiC–graphite composites using Ti-doped self-sintering carbon mesophase powder

This work reports the synthesis of nanoTiC–graphite composites using mesophase pitch containing titanium as TiC or TiO2 nanoparticles. NanoTiC–graphite composites have been prepared using Ti-doped self-sintering mesophase powders as starting materials without using any binders or a metal carbide-carbon mixing stage. The effect of manufacture variables on the graphite compacts properties was studied. Graphites were characterised using XRD and Raman spectroscopy, SEM and TEM, as well as by their mechanical, electrical and thermal properties. The presence of TiC promotes graphitisation producing materials with larger crystal sizes. The kind of titanium source and mesophase content of the starting pitch affects to the final properties. Mesophase pitch with higher amount of mesophase content produces graphites with higher degree of graphitisation. The incorporation of TiC nanoparticles to the graphites composites improved thermal conductivity more than four times, and mechanical properties are not significantly modified by the presence of TiC.

Ethylene vinyl acetate/nanoclay-based pigment composites: Morphology, rheology, and mechanical, thermal, and colorimetric properties

In this study, a new type of nanopigment, obtained from a nanoclay (NC) and a dye, was synthesized in the laboratory, and these nanopigments were used to color an ethylene vinyl acetate (EVA) copolymer. Several of these nanoclay-based pigments (NCPs) were obtained through variations in the cation exchange capacity (CEC) percentage of the NC exchanged with the dye and also including an ammonium salt. Composites of EVA and different amounts of the as-synthesized nanopigments were prepared in a melt-intercalation process. Then, the morphological, mechanical, thermal, rheological, and colorimetric properties of the samples were assessed. The EVA/NCP composites developed much better color properties than the samples containing only the dye, especially when both the dye and the ammonium salt were exchanged with NC. Their other properties were similar to those of more conventional EVA/NC composites.

Electrocatalytic oxidation of ascorbic acid on mesostructured SiO2-conducting polymer composites

The conducting self-doping copolymer poly(aniline-co-ABA) preserves its redox activity at pH values as high as 7. This observation was the starting point to synthesize an organic–inorganic hybrid composite able to electrochemically oxidize ascorbic acid molecules at that pH. The inorganic part of the catalytic element was an ordered mesoporous electrodeposit of SiO2, which has been used as the template for the electrochemical insertion of the self-doping copolymer. The oxidation of ascorbate ions at a fixed potential on this composite was studied by means of the kinetic model proposed by Bartlett and Wallace (2001). It was observed that the effective kinetic constant KME increased significantly but, simultaneously, k′ME remained almost constant when the composite was employed as the electrocatalytic substrate. These results were interpreted in the light of two combinations of kinetic constants, which strongly suggested that the increase in KME should be ascribed to the improvement in electronic conductivity of the copolymer induced by the highly ordered silica template.

Effects of Fe addition on the mechanical and thermo-mechanical properties of SiC/FeSi2/Si composites produced via reactive infiltration

Remaining silicon in SiC-based materials produced via reactive infiltration limits their use in high-temperature applications due to the poor mechanical properties of silicon: low fracture toughness, extreme fragility and creep phenomena above 1000 °C. In this paper SiC–FeSi2 composites are fabricated by reactive infiltration of Si–Fe alloys into porous Cf/C preforms. The resulting materials are SiC/FeSi2 composites, in which remaining silicon is reduced by formation of FeSi2. For the richest Fe alloys (35 wt% Fe) a nominal residual silicon content below 1% has been observed. However this, the relatively poor mechanical properties (bending strength) measured for those resulting materials can be explained by the thermal mismatch of FeSi2 and SiC, which weakens the interface and does even generate new porosity, associated with a debonding phenomenon between the two phases.

Émergence des comportements de leadership transformationnel : examen de l’apport d’une approche basée sur les composites de personnalité et d’une perspective interactionniste

Comprendre ce qui amène un leader à émettre des comportements de leadership transformationnel fascine les chercheurs et praticiens depuis plusieurs années (Bommer, Rubin, & Baldwin, 2004; Bono & Judge, 2004; Shamir & Howell, 1999 ; Stogdill, 1948; Yukl, 1999). Or, jusqu’à présent, ces facteurs sont encore bien peu étudiés et compris comparativement aux conséquences de ce style de leadership. Dans cette lignée, la présente thèse répond à différents enjeux soulevés par les auteurs à ce sujet (Dinh & Lord, 2012; Zaccaro, 2007) en cherchant à préciser le rôle joué par différents antécédents individuels et contextuels du leadership transformationnel. Cet objectif sera poursuivi par l’adoption d’une perspective interactionniste qui intègre des antécédents de personnalité et de contexte ainsi par l’évaluation de la personnalité à l’aide d’une modélisation de la personnalité orientée vers le critère à prédire (variable composite). La présente thèse est composée de trois articles poursuivant les objectifs suivant : 1) Effectuer une synthèse de la littérature empirique portant sur les antécédents individuels et contextuels du leadership transformationnel; 2) Vérifier les liens empiriques entre la personnalité mesurée à l’aide de variables composites, plus précisément le modèle des Great Eight de Bartram (2005), et le leadership transformationnel; 3) Tester empiriquement l’effet d’interaction entre les variables de personnalité et les variables contextuelles pour prédire le leadership transformationnel. Le premier article vise d’abord à circonscrire et organiser les connaissances empiriques actuelles provenant d’une quarantaine d’articles concernant les antécédents du leadership transformationnel. L’article s’organise en trois thèmes principaux : les antécédents individuels de personnalité, les antécédents contextuels et l’étude des interactions entre le volet individuel et contextuel. Plusieurs constats et pistes de recherches sont discutés et mettent la table pour les deux articles subséquents. Ainsi, le second article s’intéresse au potentiel explicatif d’un modèle de personnalité orienté vers le critère pour prédire le leadership. Plus spécifiquement, le modèle des Great Eight proposé par Bartram (2005) est mis en relation avec les comportements de leadership transformationnel et de récompense contingente. Les résultats, obtenus auprès de 113 gestionnaires et de leurs 799 subordonnés, donnent peu d’appui à la valeur ajoutée du modèle utilisé, mais indiquent que certaines tendances de personnalité sont associées au leadership. Des analyses supplémentaires permettent de nuancer la compréhension des effets observés dans la documentation scientifique et offrent quelques pistes de groupements de traits pouvant prédire les différents comportements de leadership. Le troisième article s’inspire de la théorie de l’activation des traits (Tett & Burnett, 2003) pour vérifier l’effet combiné de la personnalité du gestionnaire et du contexte dans lequel il évolue en vue de prédire le leadership transformationnel. Les résultats (ngestionnaires = 89; nsubordonnés = 643) n’offrent qu’un appui modéré au rationnel sous-jacent du modèle de l’activation des traits. Toutefois, il en ressort que l’aspect relationnel du gestionnaire (opérationnalisé par le composite de personnalité « soutien et coopération ») est associé à l’émergence du leadership transformationnel uniquement lorsque les facteurs contextuels (considération organisationnelle, latitude décisionnelle) sont perçus positivement par le gestionnaire. L’étude permet donc d’éclaircir une part de la variabilité observée dans les études antérieures concernant la tendance relationnelle du gestionnaire, en soulignant sa sensibilité à des facteurs contextuels positifs.

The Problem Sensitization Robotic Complex Drilling and Milling of Sandwich Shells of Polymer Composites

In clause is given robotic a complex for drilling and milling sandwich shells from polymeric composites. The machining of polymeric composite materials has technological problems. At drilling sandwich shells there is a probability of destruction of a drill from hit of the tool in a partition. The system sensibilization robotic complex for increase of reliability of work of the cutting tool of the small size is offered.

Émergence des comportements de leadership transformationnel : examen de l’apport d’une approche basée sur les composites de personnalité et d’une perspective interactionniste

Comprendre ce qui amène un leader à émettre des comportements de leadership transformationnel fascine les chercheurs et praticiens depuis plusieurs années (Bommer, Rubin, & Baldwin, 2004; Bono & Judge, 2004; Shamir & Howell, 1999 ; Stogdill, 1948; Yukl, 1999). Or, jusqu’à présent, ces facteurs sont encore bien peu étudiés et compris comparativement aux conséquences de ce style de leadership. Dans cette lignée, la présente thèse répond à différents enjeux soulevés par les auteurs à ce sujet (Dinh & Lord, 2012; Zaccaro, 2007) en cherchant à préciser le rôle joué par différents antécédents individuels et contextuels du leadership transformationnel. Cet objectif sera poursuivi par l’adoption d’une perspective interactionniste qui intègre des antécédents de personnalité et de contexte ainsi par l’évaluation de la personnalité à l’aide d’une modélisation de la personnalité orientée vers le critère à prédire (variable composite). La présente thèse est composée de trois articles poursuivant les objectifs suivant : 1) Effectuer une synthèse de la littérature empirique portant sur les antécédents individuels et contextuels du leadership transformationnel; 2) Vérifier les liens empiriques entre la personnalité mesurée à l’aide de variables composites, plus précisément le modèle des Great Eight de Bartram (2005), et le leadership transformationnel; 3) Tester empiriquement l’effet d’interaction entre les variables de personnalité et les variables contextuelles pour prédire le leadership transformationnel. Le premier article vise d’abord à circonscrire et organiser les connaissances empiriques actuelles provenant d’une quarantaine d’articles concernant les antécédents du leadership transformationnel. L’article s’organise en trois thèmes principaux : les antécédents individuels de personnalité, les antécédents contextuels et l’étude des interactions entre le volet individuel et contextuel. Plusieurs constats et pistes de recherches sont discutés et mettent la table pour les deux articles subséquents. Ainsi, le second article s’intéresse au potentiel explicatif d’un modèle de personnalité orienté vers le critère pour prédire le leadership. Plus spécifiquement, le modèle des Great Eight proposé par Bartram (2005) est mis en relation avec les comportements de leadership transformationnel et de récompense contingente. Les résultats, obtenus auprès de 113 gestionnaires et de leurs 799 subordonnés, donnent peu d’appui à la valeur ajoutée du modèle utilisé, mais indiquent que certaines tendances de personnalité sont associées au leadership. Des analyses supplémentaires permettent de nuancer la compréhension des effets observés dans la documentation scientifique et offrent quelques pistes de groupements de traits pouvant prédire les différents comportements de leadership. Le troisième article s’inspire de la théorie de l’activation des traits (Tett & Burnett, 2003) pour vérifier l’effet combiné de la personnalité du gestionnaire et du contexte dans lequel il évolue en vue de prédire le leadership transformationnel. Les résultats (ngestionnaires = 89; nsubordonnés = 643) n’offrent qu’un appui modéré au rationnel sous-jacent du modèle de l’activation des traits. Toutefois, il en ressort que l’aspect relationnel du gestionnaire (opérationnalisé par le composite de personnalité « soutien et coopération ») est associé à l’émergence du leadership transformationnel uniquement lorsque les facteurs contextuels (considération organisationnelle, latitude décisionnelle) sont perçus positivement par le gestionnaire. L’étude permet donc d’éclaircir une part de la variabilité observée dans les études antérieures concernant la tendance relationnelle du gestionnaire, en soulignant sa sensibilité à des facteurs contextuels positifs.

Elemental data for composites from DSDP Sites 417A, 417D, and 418A

While the input of river-alkalinity into seawater is relatively well known, the complementary acidity production is poorly understood. Using the major-element budget of seafloor alteration of the upper 500 m of 120-Ma-old oceanic crust at DSDP/ODP Sites 417A, 417D and 418A in the central western Atlantic, we estimate the acidity flux associated with the low-temperature weathering of the upper oceanic crust. The acidity flux is calculated based on major-element fluxes and charge-balance considerations. The relevant chemical fluxes from seawater to the upper crust are 4.1+-0.1; 1.4+-1.4; 2.2+-0.6 and -12+-2 10**11 mol/yr for K, Mg, Na and silicate-Ca, respectively. The associated acidity flux is (3.5+-3)10**11 eq/y. Relative to continental weathering, these fluxes are significant for K and silicate-Ca, but are minor for Na, Mg and acidity. Thus, riverine fluxes of alkalinity are not significantly balanced by acidity fluxes from low-temperature upper ocean crust alteration.