Full scale test for explosion water barriers in small cross-section galleries

Underground coal mines explosions generally arise from the inflammation of a methane/air mixture. This explosion can also generate a subsequent coal dust explosion. Traditionally such explosions have being fought eliminating one or several of the factors needed by the explosion to take place. Although several preventive measures are taken to prevent explosions, other measures should be considered to reduce the effects or even to extinguish the flame front. Unlike other protection methods that remove one or two of the explosion triangle elements, namely; the ignition source, the oxidizing agent and the fuel, explosion barriers removes all of them: reduces the quantity of coal in suspension, cools the flame front and the steam generated by vaporization removes the oxygen present in the flame. Passive water barriers are autonomous protection systems against explosions that reduce to a satisfactory safety level the effects of methane and/or flammable dust explosions. The barriers are activated by the pressure wave provoked in the explosion destroying the barrier troughs and producing a uniform dispersion of the extinguishing agent throughout the gallery section in quantity enough to extinguish the explosion flame. Full scale tests have been carried out in Polish Barbara experimental mine at GIG Central Mining Institute in order to determine the requirements and the optimal installation conditions of these devices for small sections galleries which are very frequent in the Spanish coal mines. Full scale tests results have been analyzed to understand the explosion timing and development, in order to assess on the use of water barriers in the typical small crosssection Spanish galleries. Several arrangements of water barriers have been designed and tested to verify the effectiveness of the explosion suppression in each case. The results obtained demonstrate the efficiency of the water barriers in stopping the flame front even with smaller amounts of water than those established by the European standard. According to the tests realized, water barriers activation times are between 0.52 s and 0.78 s and the flame propagation speed are between 75 m/s and 80 m/s. The maximum pressures (Pmax) obtained in the full scale tests have varied between 0.2 bar and 1.8 bar. Passive barriers protect effectively against the spread of the flame but cannot be used as a safeguard of the gallery between the ignition source and the first row of water troughs or bags, or even after them, as the pressure could remain high after them even if the flame front has been extinguished.

Efficient local unfolding with ancestor stacks for full prolog

The integration of powerful partial evaluation methods into practical compilers for logic programs is still far from reality. This is related both to 1) efficiency issues and to 2) the complications of dealing with practical programs. Regarding efnciency, the most successful unfolding rules used nowadays are based on structural orders applied over (covering) ancestors, i.e., a subsequence of the atoms selected during a derivation. Unfortunately, maintaining the structure of the ancestor relation during unfolding introduces significant overhead. We propose an efficient, practical local unfolding rule based on the notion of covering ancestors which can be used in combination with any structural order and allows a stack-based implementation without losing any opportunities for specialization. Regarding the second issue, we propose assertion-based techniques which allow our approach to deal with real programs that include (Prolog) built-ins and external predicates in a very extensible manner. Finally, we report on our implementation of these techniques in a practical partial evaluator, embedded in a state of the art compiler which uses global analysis extensively (the Ciao compiler and, specifically, its preprocessor CiaoPP). The performance analysis of the resulting system shows that our techniques, in addition to dealing with practical programs, are also significantly more efficient in time and somewhat more efficient in memory than traditional tree-based implementations.

High definition video quality assessment metric built upon full reference ratios

Métrica de calidad de video de alta definición construida a partir de ratios de referencia completa. La medida de calidad de video, en inglés Visual Quality Assessment (VQA), es uno de los mayores retos por solucionar en el entorno multimedia. La calidad de vídeo tiene un impacto altísimo en la percepción del usuario final (consumidor) de los servicios sustentados en la provisión de contenidos multimedia y, por tanto, factor clave en la valoración del nuevo paradigma denominado Calidad de la Experiencia, en inglés Quality of Experience (QoE). Los modelos de medida de calidad de vídeo se pueden agrupar en varias ramas según la base técnica que sustenta el sistema de medida, destacando en importancia los que emplean modelos psicovisuales orientados a reproducir las características del sistema visual humano, en inglés Human Visual System, del que toman sus siglas HVS, y los que, por el contrario, optan por una aproximación ingenieril en la que el cálculo de calidad está basado en la extracción de parámetros intrínsecos de la imagen y su comparación. A pesar de los avances recogidos en este campo en los últimos años, la investigación en métricas de calidad de vídeo, tanto en presencia de referencia (los modelos denominados de referencia completa), como en presencia de parte de ella (modelos de referencia reducida) e incluso los que trabajan en ausencia de la misma (denominados sin referencia), tiene un amplio camino de mejora y objetivos por alcanzar. Dentro de ellos, la medida de señales de alta definición, especialmente las utilizadas en las primeras etapas de la cadena de valor que son de muy alta calidad, son de especial interés por su influencia en la calidad final del servicio y no existen modelos fiables de medida en la actualidad. Esta tesis doctoral presenta un modelo de medida de calidad de referencia completa que hemos llamado PARMENIA (PArallel Ratios MEtric from iNtrInsic features Analysis), basado en la ponderación de cuatro ratios de calidad calculados a partir de características intrínsecas de la imagen. Son: El Ratio de Fidelidad, calculado mediante el gradiente morfológico o gradiente de Beucher. El Ratio de Similitud Visual, calculado mediante los puntos visualmente significativos de la imagen a través de filtrados locales de contraste. El Ratio de Nitidez, que procede de la extracción del estadístico de textura de Haralick contraste. El Ratio de Complejidad, obtenido de la definición de homogeneidad del conjunto de estadísticos de textura de Haralick PARMENIA presenta como novedad la utilización de la morfología matemática y estadísticos de Haralick como base de una métrica de medida de calidad, pues esas técnicas han estado tradicionalmente más ligadas a la teledetección y la segmentación de objetos. Además, la aproximación de la métrica como un conjunto ponderado de ratios es igualmente novedosa debido a que se alimenta de modelos de similitud estructural y otros más clásicos, basados en la perceptibilidad del error generado por la degradación de la señal asociada a la compresión. PARMENIA presenta resultados con una altísima correlación con las valoraciones MOS procedentes de las pruebas subjetivas a usuarios que se han realizado para la validación de la misma. El corpus de trabajo seleccionado procede de conjuntos de secuencias validados internacionalmente, de modo que los resultados aportados sean de la máxima calidad y el máximo rigor posible. La metodología de trabajo seguida ha consistido en la generación de un conjunto de secuencias de prueba de distintas calidades a través de la codificación con distintos escalones de cuantificación, la obtención de las valoraciones subjetivas de las mismas a través de pruebas subjetivas de calidad (basadas en la recomendación de la Unión Internacional de Telecomunicaciones BT.500), y la validación mediante el cálculo de la correlación de PARMENIA con estos valores subjetivos, cuantificada a través del coeficiente de correlación de Pearson. Una vez realizada la validación de los ratios y optimizada su influencia en la medida final y su alta correlación con la percepción, se ha realizado una segunda revisión sobre secuencias del hdtv test dataset 1 del Grupo de Expertos de Calidad de Vídeo (VQEG, Video Quality Expert Group) mostrando los resultados obtenidos sus claras ventajas. Abstract Visual Quality Assessment has been so far one of the most intriguing challenges on the media environment. Progressive evolution towards higher resolutions while increasing the quality needed (e.g. high definition and better image quality) aims to redefine models for quality measuring. Given the growing interest in multimedia services delivery, perceptual quality measurement has become a very active area of research. First, in this work, a classification of objective video quality metrics based on their underlying methodologies and approaches for measuring video quality has been introduced to sum up the state of the art. Then, this doctoral thesis describes an enhanced solution for full reference objective quality measurement based on mathematical morphology, texture features and visual similarity information that provides a normalized metric that we have called PARMENIA (PArallel Ratios MEtric from iNtrInsic features Analysis), with a high correlated MOS score. The PARMENIA metric is based on the pooling of different quality ratios that are obtained from three different approaches: Beucher’s gradient, local contrast filtering, and contrast and homogeneity Haralick’s texture features. The metric performance is excellent, and improves the current state of the art by providing a wide dynamic range that make easier to discriminate between very close quality coded sequences, especially for very high bit rates whose quality, currently, is transparent for quality metrics. PARMENIA introduces a degree of novelty against other working metrics: on the one hand, exploits the structural information variation to build the metric’s kernel, but complements the measure with texture information and a ratio of visual meaningful points that is closer to typical error sensitivity based approaches. We would like to point out that PARMENIA approach is the only metric built upon full reference ratios, and using mathematical morphology and texture features (typically used in segmentation) for quality assessment. On the other hand, it gets results with a wide dynamic range that allows measuring the quality of high definition sequences from bit rates of hundreds of Megabits (Mbps) down to typical distribution rates (5-6 Mbps), even streaming rates (1- 2 Mbps). Thus, a direct correlation between PARMENIA and MOS scores are easily constructed. PARMENIA may further enhance the number of available choices in objective quality measurement, especially for very high quality HD materials. All this results come from validation that has been achieved through internationally validated datasets on which subjective tests based on ITU-T BT.500 methodology have been carried out. Pearson correlation coefficient has been calculated to verify the accuracy of PARMENIA and its reliability.

Comparison of dynamic effects of high-speed traffic load on ballasted track using a simplified two-dimensional and full three-dimensional model.

The vertical dynamic actions transmitted by railway vehicles to the ballasted track infrastructure is evaluated taking into account models with different degree of detail. In particular, we have studied this matter from a two-dimensional (2D) finite element model to a fully coupled three-dimensional (3D) multi-body finite element model. The vehicle and track are coupled via a non-linear Hertz contact mechanism. The method of Lagrange multipliers is used for the contact constraint enforcement between wheel and rail. Distributed elevation irregularities are generated based on power spectral density (PSD) distributions which are taken into account for the interaction. The numerical simulations are performed in the time domain, using a direct integration method for solving the transient problem due to the contact nonlinearities. The results obtained include contact forces, forces transmitted to the infrastructure (sleeper) by railpads and envelopes of relevant results for several track irregularities and speed ranges. The main contribution of this work is to identify and discuss coincidences and differences between discrete 2D models and continuum 3D models, as wheel as assessing the validity of evaluating the dynamic loading on the track with simplified 2D models

Full-Wafer Roller-NIL Processes for Silicon Solar Cell Texturisation

The highest solar cell efficiencies both for c-Si and mc-Si were reached using template based texturing processes. Especially for mc-Si the benefit of a defined texture, the so called honeycomb texture, was demonstrated impressively. However, up until now, no industrially feasible process has been available to pattern the necessary etching masks with the sufficient resolution. Roller-Nanoimprint Lithography (Roller-NIL) has the potential to overcome these limitations and to allow high quality pattern transfers, even in the sub-micron regime, in continuous in-line processes. Therefore, this etch-mask patterning technique is a suitable solution to bring such elaborate features like the honeycomb texture to an industrial realization. Beyond that, this fast printing-like technology opens up new possibilities to introduce promising concepts like photonic structures into solar cells.

New Intermediate band sulphide nanoparticles acting in the full visible light range spectra as an active photocatalyst

Nowadays one of the challenges of materials science is to find new technologies that will be able to make the most of renewable energies. An example of new proposals in this field are the intermediate-band (IB) materials, which promise higher efficiencies in photovoltaic applications (through the intermediate band solar cells), or in heterogeneous photocatalysis (using nanoparticles of them, for the light-induced degradation of pollutants or for the efficient photoevolution of hydrogen from water). An IB material consists in a semiconductor in which gap a new level is introduced [1], the intermediate band (IB), which should be partially filled by electrons and completely separated of the valence band (VB) and of the conduction band (CB). This scheme (figure 1) allows an electron from the VB to be promoted to the IB, and from the latter to the CB, upon absorption of photons with energy below the band gap Eg, so that energy can be absorbed in a wider range of the solar spectrum and a higher current can be obtained without sacrificing the photovoltage (or the chemical driving force) corresponding to the full bandgap Eg, thus increasing the overall efficiency. This concept, applied to photocatalysis, would allow using photons of a wider visible range while keeping the same redox capacity. It is important to note that this concept differs from the classic photocatalyst doping principle, which essentially tries just to decrease the bandgap. This new type of materials would keep the full bandgap potential but would use also lower energy photons. In our group several IB materials have been proposed, mainly for the photovoltaic application, based on extensively doping known semiconductors with transition metals [2], examining with DFT calculations their electronic structures. Here we refer to In2S3 and SnS2, which contain octahedral cations; when doped with Ti or V an IB is formed according to quantum calculations (see e.g. figure 2). We have used a solvotermal synthesis method to prepare in nanocrystalline form the In2S3 thiospinel and the layered compound SnS2 (which when undoped have bandgaps of 2.0 and 2.2 eV respectively) where the cation is substituted by vanadium at a ?10% level. This substitution has been studied, characterizing the materials by different physical and chemical techniques (TXRF, XRD, HR-TEM/EDS) (see e.g. figure 3) and verifying with UV spectrometry that this substitution introduces in the spectrum the sub-bandgap features predicted by the calculations (figure 4). For both sulphide type nanoparticles (doped and undoped) the photocatalytic activity was studied by following at room temperature the oxidation of formic acid in aqueous suspension, a simple reaction which is easily monitored by UV-Vis spectroscopy. The spectral response of the process is measured using a collection of band pass filters that allow only some wavelengths into the reaction system. Thanks to this method the spectral range in which the materials are active in the photodecomposition (which coincides with the band gap for the undoped samples) can be checked, proving that for the vanadium substituted samples this range is increased, making possible to cover all the visible light range. Furthermore it is checked that these new materials are more photocorrosion resistant than the toxic CdS witch is a well know compound frequently used in tests of visible light photocatalysis. These materials are thus promising not only for degradation of pollutants (or for photovoltaic cells) but also for efficient photoevolution of hydrogen from water; work in this direction is now being pursued.

Adaptive Control for ZVS Three Phase Full Active Bridge Converter with ARCN

This paper presents an adaptive control for the auxiliary circuit, called ARCN (Auxiliary Resonant Commutating Network), used to achieve ZVS in full active bridge converters under a wide load range. Depending on the load conditions, the proposed control adapts the timing of the ARCN to minimize the losses. The principle of operation and implementation considerations are presented for a three phase full active bridge converter, proposing different methods to implement the control according to the specifications. The experimental results shown verify the proposed methodology.

Deriving the full-reducing Krivine machine from the small-step operational semantics of normal order

We derive by program transformation Pierre Crégut s full-reducing Krivine machine KN from the structural operational semantics of the normal order reduction strategy in a closure-converted pure lambda calculus. We thus establish the correspondence between the strategy and the machine, and showcase our technique for deriving full-reducing abstract machines. Actually, the machine we obtain is a slightly optimised version that can work with open terms and may be used in implementations of proof assistants.

A syntactic and functional correspondence between reduction semantics and reduction-free full normalisers

Olivier Danvy and others have shown the syntactic correspondence between reduction semantics (a small-step semantics) and abstract machines, as well as the functional correspondence between reduction-free normalisers (a big-step semantics) and abstract machines. The correspondences are established by program transformation (so-called interderivation) techniques. A reduction semantics and a reduction-free normaliser are interderivable when the abstract machine obtained from them is the same. However, the correspondences fail when the underlying reduction strategy is hybrid, i.e., relies on another sub-strategy. Hybridisation is an essential structural property of full-reducing and complete strategies. Hybridisation is unproblematic in the functional correspondence. But in the syntactic correspondence the refocusing and inlining-of-iterate-function steps become context sensitive, preventing the refunctionalisation of the abstract machine. We show how to solve the problem and showcase the interderivation of normalisers for normal order, the standard, full-reducing and complete strategy of the pure lambda calculus. Our solution makes it possible to interderive, rather than contrive, full-reducing abstract machines. As expected, the machine we obtain is a variant of Pierre Crégut s full Krivine machine KN.

Operational Aspects of Full Reduction in Lambda Calculi

Esta tesis estudia la reducción plena (‘full reduction’ en inglés) en distintos cálculos lambda. 1 En esencia, la reducción plena consiste en evaluar los cuerpos de las funciones en los lenguajes de programación funcional con ligaduras. Se toma el cálculo lambda clásico (i.e., puro y sin tipos) como el sistema formal que modela el paradigma de programación funcional. La reducción plena es una técnica fundamental cuando se considera a los programas como datos, por ejemplo para la optimización de programas mediante evaluación parcial, o cuando algún atributo del programa se representa a su vez por un programa, como el tipo en los demostradores automáticos de teoremas actuales. Muchas semánticas operacionales que realizan reducción plena tienen naturaleza híbrida. Se introduce formalmente la noción de naturaleza híbrida, que constituye el hilo conductor de todo el trabajo. En el cálculo lambda la naturaleza híbrida se manifiesta como una ‘distinción de fase’ en el tratamiento de las abstracciones, ya sean consideradas desde fuera o desde dentro de si mismas. Esta distinción de fase conlleva una estructura en capas en la que una semántica híbrida depende de una o más semánticas subsidiarias. Desde el punto de vista de los lenguajes de programación, la tesis muestra como derivar, mediante técnicas de transformación de programas, implementaciones de semánticas operacionales que reducen plenamente a partir de sus especificaciones. Las técnicas de transformación de programas consisten en transformaciones sintácticas que preservan la equivalencia semántica de los programas. Se ajustan las técnicas de transformación de programas existentes para trabajar con implementaciones de semánticas híbridas. Además, se muestra el impacto que tiene la reducción plena en las implementaciones que utilizan entornos. Los entornos son un ingrediente fundamental en las implementaciones realistas de una máquina abstracta. Desde el punto de vista de los sistemas formales, la tesis desvela una teoría novedosa para el cálculo lambda con paso por valor (‘call-by-value lambda calculus’ en inglés) que es consistente con la reducción plena. Dicha teoría induce una noción de equivalencia observacional que distingue más puntos que las teorías existentes para dicho cálculo. Esta contribución ayuda a establecer una ‘teoría estándar’ en el cálculo lambda con paso por valor que es análoga a la ‘teoría estándar’ del cálculo lambda clásico propugnada por Barendregt. Se presentan resultados de teoría de la demostración, y se sugiere como abordar el estudio de teoría de modelos. ABSTRACT This thesis studies full reduction in lambda calculi. In a nutshell, full reduction consists in evaluating the body of the functions in a functional programming language with binders. The classical (i.e., pure untyped) lambda calculus is set as the formal system that models the functional paradigm. Full reduction is a prominent technique when programs are treated as data objects, for instance when performing optimisations by partial evaluation, or when some attribute of the program is represented by a program itself, like the type in modern proof assistants. A notable feature of many full-reducing operational semantics is its hybrid nature, which is introduced and which constitutes the guiding theme of the thesis. In the lambda calculus, the hybrid nature amounts to a ‘phase distinction’ in the treatment of abstractions when considered either from outside or from inside themselves. This distinction entails a layered structure in which a hybrid semantics depends on one or more subsidiary semantics. From a programming languages standpoint, the thesis shows how to derive implementations of full-reducing operational semantics from their specifications, by using program transformations techniques. The program transformation techniques are syntactical transformations which preserve the semantic equivalence of programs. The existing program transformation techniques are adjusted to work with implementations of hybrid semantics. The thesis also shows how full reduction impacts the implementations that use the environment technique. The environment technique is a key ingredient of real-world implementations of abstract machines which helps to circumvent the issue with binders. From a formal systems standpoint, the thesis discloses a novel consistent theory for the call-by-value variant of the lambda calculus which accounts for full reduction. This novel theory entails a notion of observational equivalence which distinguishes more points than other existing theories for the call-by-value lambda calculus. This contribution helps to establish a ‘standard theory’ in that calculus which constitutes the analogous of the ‘standard theory’ advocated by Barendregt in the classical lambda calculus. Some prooftheoretical results are presented, and insights on the model-theoretical study are given.

Development of a full hybrid lighting-CPV prototype and savings in a real case operation

A full Hybrid lighting-CPV prototype has been assembled. This new concept mixes a classical CPV module with the production of light for illumination without a double conversion (solar energy to electricity and electricity to light) allowing a higher efficiency to the whole system. The present prototype is based on a commercial CPV module that has been adapted in order to be hybrid, adjusting the receivers to pass the fibers into the module, inserting a holder to adjust x,y and z position of the fibers and changing the original parquet of lenses by a bifocal one composed most of the original lenses and the inclusion of other lenses in the position of the corners. Results show that with a minimal loss in the CPV part, a luminous flux is obtained that can be used to illuminate. Adding an additional electrical lamp and a light sensor that enables this lamp when no light from the sun is received, a 38% saving on lighting electricity is expected in Madrid during a year.

Transcripts from a single full-length cDNA clone of hepatitis C virus are infectious when directly transfected into the liver of a chimpanzee

We have succeeded in constructing a stable full-length cDNA clone of strain H77 (genotype 1a) of hepatitis C virus (HCV). We devised a cassette vector with fixed 5′ and 3′ termini and constructed multiple full-length cDNA clones of H77 in a single step by cloning of the entire ORF, which was amplified by long reverse transcriptase–PCR, directly into this vector. The infectivity of two complete full-length cDNA clones was tested by the direct intrahepatic injection of a chimpanzee with RNA transcripts. However, we found no evidence for HCV replication. Sequence analysis of these and 16 additional full-length clones revealed that seven clones were defective for polyprotein synthesis, and the remaining nine clones had 6–28 amino acid mutations in the predicted polyprotein compared with the consensus sequence of H77. Next, we constructed a consensus chimera from four of the full-length cDNA clones with just two ligation steps. Injection of RNA transcripts from this consensus clone into the liver of a chimpanzee resulted in viral replication. The sequence of the virus recovered from the chimpanzee was identical to that of the injected RNA transcripts. This stable infectious molecular clone should be an important tool for developing a better understanding of the molecular biology and pathogenesis of HCV.

Full Bridge MMC Converter Optimal Design to HVDC Operational Requirements

This project is funded by RTE, Paris, France

Transgenic potato (Solanum tuberosum) tubers synthesize the full spectrum of inulin molecules naturally occurring in globe artichoke (Cynara scolymus) roots

The ability to synthesize high molecular weight inulin was transferred to potato plants via constitutive expression of the 1-SST (sucrose:sucrose 1-fructosyltransferase) and the 1-FFT (fructan: fructan 1-fructosyltransferase) genes of globe artichoke (Cynara scolymus). The fructan pattern of tubers from transgenic potato plants represents the full spectrum of inulin molecules present in artichoke roots as shown by high-performance anion exchange chromatography, as well as size exclusion chromatography. These results demonstrate in planta that the enzymes sucrose:sucrose 1-fructosyltransferase and fructan:fructan 1-fructosyltransferase are sufficient to synthesize inulin molecules of all chain lengths naturally occurring in a given plant species. Inulin made up 5% of the dry weight of transgenic tubers, and a low level of fructan production also was observed in fully expanded leaves. Although inulin accumulation did not influence the sucrose concentration in leaves or tubers, a reduction in starch content occurred in transgenic tubers, indicating that inulin synthesis did not increase the storage capacity of the tubers.