Caracterização mineralógica de Latossolos em diferentes feições do relevo na região de Jaboticabal, SP

Different surface land form expressed by the relief can cause variations in soil properties in different magnitudes, depending mainly on a specific location in the landscape. Therefore, the objective of this study was to make the mineralogical characterization of Oxisols in different relief forms in the region of Jaboticabal, SP. Three trenches were opened in the convex, linear and concave landforms, done morphological description of the soil horizons and collected soil samples for physical, chemical and mineralogical characterization. It was found that the oxidic mineralogy is dependent on the type of landform, with the dominance of goethite on the concave landform and hematite on the linear landform. The desferrific clay minerals exhibited dominance of gibbsite in the concave, compared to convex and linear landforms that were dominated by the kaolinitic mineralogy.

Análise da Conformidade e Caracterização da Matéria- Prima Empregada na Fabricação de Blocos Cerâmicos na Região Metropolitana de Salvador

The potential market of the metropolitan area of Salvador accounts for the estimated consumption of roughly 800 million horizontally perforated extruded clay bricks a year. The growing demand of consumers along with the competitiveness of the structural ceramic sector has driven forward a number of recent efforts and investments towards improving the quality of structural ceramics. In this scenario, the present study focused on sampling and evaluating the conformity of 8-hole horizontally perforated extruded clay bricks manufactured by different plants (A, B and C) in the metropolitan area of Salvador. In addition, representative clay and sandy-clay materials were collected from each plant and characterized by conventional physical, chemical and mineralogical techniques. Finally, experimental compositions designated as A, B and C, according to the source, were prepared by mixing different contents of the raw materials collected in the plants, fired at different temperatures and characterized. The results revealed a series of non conformities regarding ABNT guidelines. The characterization of raw materials revealed the presence of kaolinite and ilite in concentrations ranging from 64 to 90 wt.% along with free quartz (10 - 25%). The sandy-clay samples consisted basically of kaolinite. All raw materials depicted low contents of organics, amorphous constituents, alkaline oxides and feldspar. An analysis of the firing behavior of all different ceramic compositions revealed that the linear contraction of composition A was rather significant considering the temperature range evaluated, and it justifies the significant dimensional non conformity that was shown by bricks made with the ceramic A

A influência da adição de caulim, quartzo e feldspato potássico na formulação de massas cerâmicas para telhas: Modelo estatístico

The production of roof tiles in the state of Rio Grande do Norte accounts for around 60% of the total of ceramic pieces produced. There is a need for investment to improve quality and productivity, thereby promoting technological innovations. Accordingly, the aim of this study is to determine the effect of kaolin, potassium feldspar and quartz in two standard formulations, as well as the effect of sintering temperature on the technological properties of linear firing shrinkage, water absorption and bending rupture stress, by fitting the statistical model and using multiple linear regression to assess the relationship between technological properties and independent variables. The raw materials were characterized using the following techniques: X-ray fluorescence (XRF), X-ray diffraction (XRF), rational analysis (RA), differential thermal analysis (DTA) and granulometric analysis (GA). The test specimens were compacted by uniaxial pressure (25 MPa), dried in a stove at 110 ºC for 24 hours and sinterized at 850 ºC, 950 ºC and 1050 ºC and held isothermal for 30 minutes. The results obtained indicate that the addition of kaolin to two standard formulations (M and R) promoted a reduction in water absorption values and an increase in bending rupture stress values. The sintering temperatures for group M that resulted in the lowest linear firing shrinkage and water absorption values were 850 ºC and 950 ºC, respectively, and the highest bending rupture stress values were reached at a temperature of 950 ºC. In the case of group R, the sintering temperature that obtained the lowest water absorption and linear firing shrinkage values was 850 ºC, and the highest bending rupture stress values were attained at a temperature of 1050 ºC. This work explains the statistical approach used to fit the model that describes the relationship between the technological properties and percentage of kaolin, quartz and feldspar, as well as the models that enable predictions, provided that the lower and upper limits of the percentage of clay minerals, flux and quartz used in this study are respected. Statistica 6 software was used and results were obtained by stepwise forward regression

Oxidação úmida de fenóis com catalisadores de ferro suportado em argilominerais em reator de leito de lama (slurry)

The wet oxidation of organic compounds with CO2 and H2O has been demonstrated to be an efficient technique for effluent treatment. This work focuses on the synthesis, characterization and catalytic performance of Fe-MnO2/CeO2, K-MnO2/CeO2/ palygorskite and Fe/ palygorskite toward the wet oxidative degradation of phenol. The experiments were conducted in a sludge bed reactor with controlled temperature, pressure and stirring speed and sampling of the liquid phase. Experiments were performed on the following operating conditions: temperature 130 ° C, pressure 20.4 atm, catalyst mass concentration of 5 g / L initial concentration of phenol and 0.5 g / L. The catalytic tests were performed in a slurry agitated reactor provided with temperature, pressure and agitation control and reactor liquid sampling. The influences of iron loaded on the support (0.3; 7 and 10%, m/m) and the initial pH of the reactant medium (3.1; 6.8; 8.7) were studied. The iron dispersion on the palygorskite, the phase purity and the elemental composition of the catalyst were evaluated by X-Ray Difraction (XRD), Scanning Electron Microscopy (SEM) and X-Ray Flourescence (XRF). The use of palygorskite as support to increase the surface area was confirmed by the B.E.T. surface results. The phenol degradation curves showed that the Fe3+ over palygorskite when compared with the other materials tested has the best performance toward the (Total Organic carbonic) TOC conversion. The decrease in alkalinity of the reaction medium also favors the conversion of TOC. The maximum conversion obtained from the TOC with the catalyst 3% Fe / palygorskite was around 95% for a reaction time of 60 minutes, while reducing the formation of acids, especially acetic acid. With products obtained from wet oxidation of phenol, hydroquinone, p-benzoquinone, catechol and oxalic acid, identified and quantified by High Performance Liquid Chromatography was possible to propose a reaction mechanism of the process where the phenol is transformed into the homogeneous and heterogeneous phase in the other by applying a kinetic model, Langmuir-Hinshelwood type, with evaluation of kinetic constants of different reactions involved.

Interpretation of Resistivity Piezocone Tests in a Contaminated Municipal Solid Waste Disposal Site

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de uma metodologia para caracterização de amostras de sedimento: Rio Jundiaí RN

The study of sediment in water bodies presents great environmental importance, because of its ability to adsorb the pollutants, they may facilitate the understanding of the history of the current quality of the water system. Depending on how it is done the collection, analysis can show both a recent contamination as old. The detailed characterization of the sediment may reveal details that can understand how each type of pollutant interacts with the material given its composition. In this work it has developed a systematic methodology to characterize samples of sediment, with the aim to understand how a series of metal is distributed in different size fractions of the sediment. This study was conducted in five samples of sediment (P1, P2, P3a, P3B and P3c) collected in Jundiaí river, one of the most important tributaries of the river Potengi in the region of Macaíba, RN. The characterization was made with the samples previously sieved into meshes with different granulometries (+8#, -8+16#, -16+65# - 65+100#,-100+200#,-200+250# and -250#), using the following techniques: Analysis of specific surface area by BET method, determining the levels of organic matter (OM%) and humidity through the gravimetry and Analysis Thermogravimetric (TG), Infrared Spectroscopy in a Fourier transform (FTIR ), Analysis of X ray diffraction (XRD), analysis of heavy metals by optical emission spectrometry with the Argon Plasma (ICP-OES). The analyzed elements were Al, Cd, Cr, Cu, Fe, Mn, Ni, Zn and P. In addition to the techniques of characterization above, was also made the rebuilding of the samples P1, P2 and P3B in relation to the levels of organic matter and concentration of heavy metals. Then, the results of the recomposed samples were compared with those obtained in crude samples, showing great consistency. The gravimetry, used in determining the levels of organic matter, was not considered an appropriate method because the clay minerals present in the sediment samples analyzed fall apart in the same range of temperature (550-600 0C) used in roasting (600 0C). The results also showed the trend of organic matter and heavy metals to focus on the thin fractions, although the largest concentrations of metals are in intermediate fractions

Hidrofobização, caracterização e aplicação da vermiculita para remoção de óleo insolúvel em água

Among the various layered silicates, vermiculite has been used as one of the adsorbent material by presenting the ion exchange capacity which facilitates the removal of organic compounds which are potential pollutants in relation to the water surface. The importance of the modification of clay minerals by hydrophobization with carnauba wax establishes the increase in oil removal capacity in aqueous medium, it contributes to a better environment for life in ecosystems. The vermiculite when expanded decreases its hydrophobicity requiring the use of a hydrophobizing leaving - the organoclay. In this work were used in the process of modifying the particle sizes of vermiculite -18+16, -16 +20 and -20 +35 #. Samples of vermiculite hydrophobized with carnauba wax and clay mineral without hydrophobizing were characterized with physicochemical analyzes and analytical. Techniques were used: thermal analysis (thermogravimetry and derivative thermogravimetry), infrared spectroscopy, scanning electron microscopy, fluorescence rays - x adsorption tests. The TG / DTG was used to evaluate the thermal behavior of expanded vermiculite and carnauba wax and samples hidrofobizadas with percentages of 5, 10 and 15 % by weight of hydrophobizing. The results of FTIR confirmed increase of the characteristic signs of carnauba wax in samples hidrofobizadas as the greatest amount of hydrophobizing the clay mineral used in hydrophobization. Thermogravimetry and FTIR show based on the results that coating the surface of the vermiculite occur homogeneously. The data obtained by the technique of x-ray fluorescence with loss on ignition confirmed the results of thermogravimetric analysis in relation to the percentage of wax incorporated. The fluorescence indicates through information provided by the analysis shows that the material covered - is homogeneous. The mev inspection was used to texture and morphology of the clay mineral with and without carnauba wax. The scanning electron microscopy confirms the deposition of wax evenly over the surface of the mineral as indicated by the other techniques. To verify the adsorption capacity of the clay without hydrophobizing hydrophobized and used a fixed volume of water to 1 ½ liters in each experiment with 3 g to 50 g of oil sample. The results show that better extraction of oil for the material processed corresponds to 260 % relative to the weight of the sample coated and greater than 80 % of the oil drop in the system

Variação espacial e sazonal de elementos maiores e traços no estuários do Rio Curimataú (RN), através de dados geoquímicos e de sensoriamento remoto

The Curimataú estuary is located in the oriental coast of Rio Grande do Norte State in Brazil. Its importance resides in the fact that this region possesses one of the last portions of preserved mangrove in the Rio Grande do Norte State. Nevertheless, it has been severely affected by many anthropogenic activities, as sugarcane monoculture and shrimp farming. Former works demonstrated that an accumulation of heavy metals is occurring in oysters in this estuary, and perhaps it could be explained by the input of metals in this ecosystem deriving from the shrimp farming. To better understanding the origin of these metals, bottom sediment samples, cores and suspended particulate matter were collected for a characterization of metal concentrations (Al, Ba, Cd, Cu, Cr, Fe, Mn, Ni, Pb, Zn) and to determine the potentially bioavailable metals. Additionally, the enrichment ratio for each element analyzed was calculated. The mineralogical composition of sediment samples and cores were obtained by X-ray diffraction. Moreover, data of orbital remote sensing were used in order to detect and quantify suspended matter by applying a logarithmic algorithm. Geochemical data of bottom sediments and cores revealed that, excepting Ba and Pb, the elements analyzed presented concentrations characteristic of an unpolluted ecosystem (Al: 0,25 - 8,76 %; Ba: 3,03 - 870 µg.g-1; Cd: < 0,25 µg.g-1; Cr: 1,72 - 82,4 µg.g-1; Cu: 0,12 -25,3 µg.g-1; Pb: 0,38 - 23,7 µg.g-1; Fe: 0,10 - 5,82 %; Mn: 15,1 - 815 µg.g-1; Ni: 0,14 - 36,1 µg.g-1; Zn: 1,37 - 113 µg.g-1). During the dry season a distribution pattern was observed, with higher metal concentrations in the margins, decreasing toward the central portion of the channel. These metal concentrations were well correlated with mineralogical compositions, with clay minerals prevailing at the margins, and quartz and feldspar in the center. However, this pattern was not observed during the wet season, probably because of the high water flux that disturbed bottom sediments. But, as observed for the dry season, a good correlation between metal concentrations and mineralogical composition was also observed for the wet season, with high metal concentrations where there were high quantities of clay minerals. Low enrichment ratios were obtained for the majority of elements analyzed, excepting for Mn, Ba and Pb. Manganese presented the higher ratios downstream for both seasons, and it can be an evidence of anthropogenic impact by shrimp farming. As barium and lead concentrations in sediment samples presented analytical problems during the total sample digestion, one cannot be sure that the ratios obtained correspond to the reality. The highest metal concentrations in particulate matter were obtained in the portion dominated by fluvial transport for all metals analyzed, excepting for copper. Barium and zinc were the only elements that presented elevated concentrations that are not common of unpolluted ecosystems (Ba: 5730 - 8355 µg.g-1; Zn: 3899 - 4348 µg.g-1). However, these high concentrations could not be related to the shrimp farming and waste waters from the town of Canguaretama, once they were obtained from the fluvial particulate matter, that is upstream from the activities above mentioned. The application of the logarithmic algorithm to the processed LANDSAT image was well succeeded, although the acquired image does not correspond exactly to the field campaigns. The IKONOS image provided very detailed views of the suspended sediment concentration at the estuary, as the mixture of distinct water flows at the confluence of Cunhaú and Curimataú rivers, with more turbid waters from Cunhaú river, that is directly affected by effluents from shrimp farming and urban waste waters deriving from the town of Canguaretama

Caracterização e análise do talude continental adjacente à bacia potiguar, NE Brasil

This work presents the results of the first imaging of continental slope adjacent to Potiguar Basin, in the equatorial Brazilian margin (NE Brazil). Swath bathymetry provided a complete coverage of seafloor between the upper and middle slope (100-1,300 m). Fifteen submarine canyons were mapped. The shape of the slope reflects in distinct spatial distribution of the canyons. The western area displays convex profiles which implied a greater amount of incisions by canyons. Some of them have gradient walls higher than 35°. They were classified according to location and morphology. The canyons with heads indenting shelf edge, association with a incised valley and a large fluvial system, high sinuosities, V shape, terraces along margins, further erosive features such as landslide and gullies allow to deduce a sandy-gravelly sedimentation. These canyons are associated with deposition of submarine fan systems that have been considered permeable hydrocarbon reservoirs. The presence of gullies, furrows and dunes demonstrates the role of bottom currents in the shaping of the slope. The enlargement of canyons and the change in the course when they cross the border fault imply that tectonic has also influenced in the morphology of deep waters environments of Potiguar Basin. The current sedimentation of continental slope is considered mixed because the sediments are composed of siliciclastics and bioclasts. Predominant siliciclastics are calcite, dolomite, quartz, and clay minerals. The presence of stable minerals (zircon, tourmaline and rutile), and fragmented bioclasts implies the contributions of Rivers Açu and Apodi

Caracterização da matéria-prima cerâmica da Mina Tabajara (Limeira, SP)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Micromorphology and spectroscopic characteristics of organic matter in waterlogged podzols of the upper Amazon basin

In waterlogged environments of the upper Amazon basin, organic matter is a major driver in the podzolisation of clay-depleted laterites, especially through its ability to weather clay minerals and chelate metals. Its structure in eight organic-rich samples collected at the margin and in the centre of the podzolic area of a soil sequence was investigated. The samples illustrate the main steps in the development of waterlogged podzols and belong either to eluviated topsoil A horizons or to illuviated subsoil Bhs, Bh and 2BCs horizons. Organic matter micromorphology was described, and the overall molecular structure of their clay size fractions was assessed using Fourier transform infrared (FTIR) spectroscopy and cross polarization/magic angle spinning (CP/MAS) C-13 nuclear magnetic resonance (NMR). Organic features of the horizons strongly vary both vertically and laterally in the sequence. Topsoil A horizons are dominated by organic residues juxtaposed to clean sands with a major aliphatic contribution. In the subsoil, numerous coatings, characteristic of illuviation processes, are observed in the following horizons: (i) At the margin and bottom parts of the podzolic area, dark brown organic compounds of low aromacity with abundant oxygen-containing groups accumulate in Bhs and 2BCs horizons. Their spectroscopic features agree with the observation of cracked coatings in 2BCs and the presence of organometallic complexes, whose abundance decreases towards low lying positions. (ii) By contrast, black organic compounds of high aromacity with few chelating functions accumulate as coatings and infills in the overlying sandy Bh horizon of well-expressed waterlogged podzols. (c) 2008 Elsevier B.V. All rights reserved.

Simulação geoestatística na caracterização espacial de óxidos de ferro em diferentes pedoformas

Os minerais da fração argila, goethita e hematita, são óxidos de ferro (Fe) indicadores pedoambientais com grande influência nos atributos físicos e químicos do solo. O conhecimento dos padrões espaciais desses óxidos auxilia a compreensão das interrelações de causa e efeito com os atributos do solo. Nesse sentido, a qualidade das estimativas espaciais produzidas pode alterar os resultados obtidos e, por consequência, as interpretações dos padrões espaciais obtidos. O presente estudo teve o objetivo de avaliar o desempenho dos métodos geoestatísticos de estimativas (KO) e simulações sequenciais gaussianas (SSG) na caracterização espacial de teores de óxidos de Fe, goethita (Gt) e hematita (Hm), em uma pedoforma côncava e outra convexa. Foram coletadas 121 amostras de solos em cada pedoforma de um Argissolo em pontos com espaçamentos regulares de 10 m. Os teores de óxidos de Fe foram obtidos por meio de difração de raios-X. Os dados foram submetidos a análises geoestatísticas por meio da modelagem do variograma e posterior interpolação por KO e SSG. A KO não refletiu a verdadeira variabilidade dos óxidos de Fe, hematita e goethita, demonstrando ser inapropriada para a caracterização espacial dos teores dos óxidos de Fe. Assim, o uso da SSG é preferível à krigagem quando a manutenção dos altos e baixos valores nas estimativas espaciais é necessária. O desempenho dos métodos geoestatísticos foi influenciado pelas pedoformas. Os mapas E-type devem ser recomendados em vez de mapas de KO para os óxidos de Fe, por serem ricos em detalhes e práticos na definição de zonas homogêneas para o manejo localizado em frente de KO, sobretudo em pedoforma côncava.

Physical and mechanical properties of ceramics from clays of the west of S. Paulo State, Brazil

Argilas de interesse da indústria de cerâmica estrutural foram caracterizadas. Algumas propriedades físicas de diversas massas cerâmicas, preparadas a partir de material coletado em depósitos artificiais, também foram analisadas. Todas as massas investigadas exibem alta concentração de componentes finos (< 2 mim) e considerável grau de plasticidade, o que é compatível com a presença de elevado teor de argilominerais. Corpos de prova cerâmicos foram preparados por prensagem a seco e queimados em temperaturas ao redor de 855 °C. Os parâmetros resistência mecânica à flexão, retração linear, absorção de água, cor aparente e perda de peso foram medidos. Como resultado, as aplicações industriais destas matérias primas foram analisadas e revistas, bem como novas aplicações foram propostas.

Aplicação de programa de análise de imagens na interpretação de fotomicrografias de alta resolução de argilominerais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo das argilas das olarias dos municípios de Alfenas e Areado, MG

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)