Shear bond strength of metal-ceramic repair systems

Statement of problem. When clinical fractures of the ceramic veneer on metal-ceramic prostheses can be repaired, the need for remake may be eliminated or postponed. Many different ceramic repair materials are available, and bond strength data are necessary for predicting the success of a given repair system.Purpose. This study evaluated the shear bond strength of different repair systems for metal-ceramic restorations applied on metal and porcelain.Material and methods. Fifty cylindrical specimens (9 X 3 mm) were fabricated in a nickel-chromium alloy (Vera Bond 11) and 50 in feldspathic porcelain (Noritakc). Metal (M) and porcelain (P) specimens were embedded in a polyvinyl chloride (PVC) ring and received I of the following bonding and resin composite repair systems (n=10): Clearfil SE Bond/Clearfil AP-X (CL), Bistite II DC/Palfique (BT), Cojet Sand/Z100 (Q), Scotchbond Multipurpose Plus/Z100 (SB) (control group), or Cojet Sand plus Scotchbond Multipurpose Plus/Z100 (CJSB). The specimens were stored in distilled water for 24 hours at 37 degrees C, thermal cycled (1000 cycles at 5 degrees C to 55 degrees C), and stored at 37 degrees C for 8 days. Shear bond tests between the metal or ceramic specimens and repair systems were performed in a mechanical testing machine with a crosshead speed of 0.5 mm/min. Mean shear bond strength values (MPa) were submitted to 1-way ANOVA and Tukey honestly significant difference tests (alpha=.05). Each specimen was examined under a stereoscopic lens with X 30 magnification, and mode of failure was classified as adhesive, cohesive, or a combination.Results. on metal, the mean shear bond strength values for the groups were as follows: MCL, 18.40 +/- 2.88(b); MBT, 8.57 +/- 1.00(d); MCJ, 25.24 +/- 3.46(a); MSB, 16.26 +/- 3.09(bc); and MCJSB, 13.11 +/- 1.24(c). on porcelain, the mean shear bond strength values ofeach group were as follows: PCL, 16.91 +/- 2.22(b); PBT, 18.04 +/- 3.2(ab); PCJ, 19.54 +/- 3.77(ab); PSB, 21.05 +/- 3.22(a); and PCJSB, 16.18 +/- 1.71(b). Within each substrate, identical superscript letters denote no significant differences among groups.Conclusions. The bond strength for the metal substrate was significantly higher using the Q system. For porcelain, SB, Q, and BT systems showed the highest shear bond strength values, and only SB was significantly different compared to CL and CJSB (P <.05).

EFFECT of DIFFERENT AIRBORNE-PARTICLE ABRASION/BONDING AGENT COMBINATIONS on THE BOND STRENGTH of A RESIN CEMENT TO A BASE METAL ALLOY

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação da demanda química de oxigênio em águas por espectrofotometria simultânea dos íons crômio(III) e dicromato

Propõe-se metodologia analítica para a determinação da demanda química de oxigênio(DQO) em águas e efluentes pouco poluídos, pela espectrofotometria simultânea dos íons crômio(III) e dicromato, após a clássica oxidação sulfocrômica das amostras, à quente e catalisada por íons Ag+. Demonstra-se que a inter-relação entre as concentrações de DQO, de crômio(III) formado e de dicromato residual permite simplificar a resolução numérica do sistema - de multicomponente, envolvendo as concentrações desses dois íons, e medidas de absorbância em pelo menos dois comprimentos de onda para monocomponente, envolvendo diretamente a concentração em DQO, e medida de absorbância num único comprimento de onda.

Aproveitamento de alimentos de origem animal pela tartaruga-da-amazônia: Podocnemis expansa criada em cativeiro

Foi realizado um trabalho para determinar o aproveitamento alimentar da farinha de carne e ossos (FCO), farinha de vísceras de aves (FVA) e farinha de peixe (FP) em tartaruga-da-amazônia, por meio dos coeficientes de digestibilidade aparente (CDA) da matéria seca (MS), proteína bruta (PB), extrato etéreo (EE) e energia bruta (EB). Os animais experimentais foram 136 filhotes provenientes do Projeto Quelônios da Amazônia, no estado do Mato Grosso, mantidos em caixas com renovação de água e temperatura média de 29ºC. Os CDA foram determinados com dietas contendo 0,1% do marcador óxido de crômio III (Cr2O3). Os CDA da MS, PB, EE e EB foram, respectivamente, de 79,10; 87,61; 93,83 e 79,61% para FCO; 92,45; 94,89; 96,55 e 92,71% para FV e 93,53; 95,13; 94,05 e 93,18% para FP. Os melhores coeficientes foram obtidos com a farinha de peixe e a farinha de vísceras de aves.

Structural and spectroscopic characterization of Al2-xCrxO3 powders obtained by polymeric precursor method

Al2O3 and Al2-x Cr (x) O-3 (x = 0.01, 0.02 and 0.04) powders have been synthesized by the polymeric precursors method. A study of the structural evolution of crystalline phases corresponding to the obtained powders was accomplished through X-Ray Diffraction and UV-vis spectroscopy (reflectance spectra and CIEL* a*b* color data). The obtained results allow to identify the gamma-Al2O3 to alpha-Al2O3 phase transition. The single-phase alpha-Al2O3 powder was obtained after heat treatment at 1050 degrees C for 2 h. The results show that the green to red color transition and ruby luminescence lines observed for the powders of Al2-x Cr (x) O-3 are related to the gamma to alpha-Al2O3 phase transition and the temperature and time range for such transition depends on the chromium content.

Electrochemical and structural characterization of heat-treated Cr3C2-NiCr coatings

The influence of heat-treatments on the electrochemical behavior of thermal spray Cr3C2-NiCr coatings prepared by high velocity oxygen fuel (HVOF) was studied in NaCl solution, at 25 degrees C, using open-circuit potential (E-OC) and electrochemical impedance spectroscopy (EIS) measurements. Coating characterization were performed before and after the heat-treatments and electrochemical tests by scanning electron microscopy, X-ray diffraction, and Auger electron spectroscopy. In addition to the changes in the original powder composition occurring during HVOF process, heat-treatment performed at 450 degrees C caused no significant changes in electrochemical response compared with untreated sample, and at 760 degrees C the main difference was the formation of a thin and defective layer of Cr2O3 at the coating surface, which increased the total impedance at the first day of immersion. Higher influence on the electrochemical was noted for samples treated at 880 degrees C, which also showed higher E-OC and total impedance, and lower corrosion current. This behavior was interpreted considering the formation of a chromium oxide layer on the coating surface, dissolution and decomposition of smaller carbide particles and their surface enrichment with Cr due to C diffusion and dissolution into the matrix, and possible Ni, Cr, and Fe diffusion to coating/substrate interface. (c) 2006 the Electrochemical Society.

Influence of HVOF parameters on the corrosion and wear resistance of WC-Co coatings sprayed on AA7050 T7

Thermal spray WC-based coatings are widely used in the aircraft industry mainly for their resistance to wear, reworking and rebuilding operations and repair of worn components on landing gear, hydraulic cylinders, actuators, propeller hub assemblies, gas turbine engines, and so on. The aircraft industry is also trying to use thermal spray technology to replace electroplating coatings such as hard chromium. In the present work, WC-Co coatings were built up on an AA 7050 aluminum alloy using high velocity oxygen fuel (HVOF) technology and a liquid nitrogen cooling prototype system. The influence of the spray parameters (standard conditions, W19S, increasing the oxygen flux, W19H, and also increasing the carrier gas flux, W19F) on corrosion, friction, and abrasive wear resistance were also studied. The coatings were characterized using optical (OM) and scanning electron (SEM) microscopy, and X-ray diffraction (XRD). The friction and abrasive wear resistance of the coatings were studied using Rubber Wheel and Ball on Disk tests. The electrochemical studies were conducted using open-circuit potential (E(oc)) measurements and electrochemical impedance spectroscopy (EIS). Differences among coated samples were mainly related to the variation of the thermal spray parameters used during the spray process. No significant differences were observed in the wear resistance for the coatings studied, and all of them showed a wear rate around 10 times lower than that of the aluminum alloy. The results of mass loss and wear rate were interpreted considering different mechanisms. Comparing the different spray parameters, the oxygen flux (higher flame temperature) produced the sample which showed the highest corrosion resistance in aerated and unstirred 3.5% NaCl solution. Aluminum ions were detected on the surface almost immediately after the immersion of samples W19S and W19F in chloride solution, showing that the electrolyte reached the substrate and galvanic corrosion probably occurred. For sample W19H, aluminum ions were not detected even after 120 min of immersion in NaCl solution. (C) 2008 Elsevier B.V. All rights reserved.

Electrochemical study of TEOS, TEOS/MPTS, MPTS/MMA and TEOS/MPTS/MMA films on tin coated steel in 3.5% NaCl solution

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Corrosion and Wear Studies of Cr3C2NiCr-HVOF Coatings Sprayed on AA7050 T7 Under Cooling

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Distribuição e biodisponibilidade de crômio em solos contaminados por resíduos de couro

DISTRIBUTION and BIOAVAILABILITY of CHROMIUM IN CONTAMINATED SOILS BY TANNERY RESIDUES. Samples of soil, water and sediment were collected and analyzed in order to evaluate chromium contamination due to deposition of tannery residues onto soils under different management regimes. The results showed that soils used for sugar cane cultivation were not adversely impacted. However, in the case of mango plantations, variable concentrations of chromium were measured in the soil profile, with 22.2% of values being higher than permitted legal limits, and 38.9% being at levels requiring remediation. Concentrations of bioavailable chromium were lower than the detection limit of the method (0.01 mg of chromium kg(-1) of soil), indicating that all of the chromium present in the samples was either complexed or in an insoluble form. Chromium concentrations measured in samples of water and sediments were indicative of low mobility of the metal in soils. The main cause of differences found between soil samples obtained from different cultivations was the type of soil management.

Environmental evaluation of metals in sediments and dragonflies due to sugar cane cultivation in neotropical streams

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Redução de crômio hexavalente por substâncias húmicas aquáticas imobilizadas em aminopropil sílica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Production of defects in ZBLAN, ZBLAN : Tm3+ and ZBLAN : Cr3+ glasses by ultra-short pulses laser interaction

In this work we have studied pure and thulium- and chromium-doped ZBLAN glasses irradiated by ultra-short laser pulses. A Ti:sapphire CPA system was used, producing a 500 Hz train of pulses, centered at 830 nm, with 375 mu J of energy and 50 fs of duration (FWHM). The beam was focused by a 20 Him lens, producing a converging beam with a waist of 12 pin. The absorption spectra before and after laser irradiation were obtained showing production of color centers in pure, thulium-doped and chromium-doped ZBLAN glasses. A damage threshold of 9.56 TW/cm(2) was determined for ZBLAN. (C) 2007 Elsevier Ltd. All rights reserved.

Daily intake of lactating crossbred cows grazing elephant grass rotationally

O objetivo deste trabalho foi o de estimar o consumo total e o diário de matéria seca do pasto, de vacas mestiças Holandês - Zebu, em piquetes de capim-elefante (Pennisetum purpureum Schum.). Três grupos de 24 vacas foram usados em piquetes (4,5 vacas/ha), pastejados por três dias e submetidos a diferentes períodos de descanso durante dois anos. Os tratamentos consistiram de descansos de 30 dias sem concentrado e 30, 37,5 e 45 dias com a suplementação de 2 kg de concentrado (20,6% de proteína bruta). de julho a outubro, as vacas receberam, como suplementação, cana-de-açúcar mais 1% de uréia. O consumo total de matéria seca foi estimado a partir da digestibilidade in vitro da matéria seca da extrusa e da produção fecal obtida com óxido crômico. Independentemente do tratamento, o consumo total foi 2,7; 2,9 e 2.9±0,03%, e o consumo de matéria seca do pasto foi de 1,9; 2,1 e 2,1±0,03% do peso vivo (p<0,05), respectivamente, no primeiro, segundo e terceiro dia de ocupação do piquete. Somente no verão, o consumo do pasto foi semelhante nos três dias de pastejo. A mistura cana-de-açúcar e uréia substituiu o pasto, principalmente no primeiro dia de pastejo, ocasião em que o consumo do pasto era mais baixo.

Composição corporal e eficiência de utilização de nutrientes por pacus alimentados com ração suplementada com cromo trivalente

O objetivo deste trabalho foi avaliar a composição corporal e a eficiência de utilização de nutrientes por pacus alimentados com dieta suplementada com cromo trivalente e mantidos em duas densidades de estocagem. O delineamento experimental foi inteiramente ao acaso com 24 tratamentos, em esquema fatorial: quatro níveis de cromo na ração (0, 6, 12, 18 mg kg-1), duas densidades de estocagem (4 e 20 kg m-3) e três períodos de avaliação (30, 60 e 90 dias) com quatro repetições. Foram observados aumentos significativos na eficiência de retenção de proteína bruta e na porcentagem de proteína bruta na carcaça, diminuição de eficiência de retenção de gordura e menores valores de porcentagem de gordura na carcaça dos pacus alimentados com ração suplementada. O nível de cromo de 6 mg kg-1 foi suficiente para possibilitar, na menor densidade, o maior acúmulo de proteína e menor teor de gordura na carcaça, ao passo que, na maior densidade, a exigência de cromo foi mais alta (12 mg kg-1), para obtenção de resultados semelhantes. Pacus alimentados com dietas suplementadas com cromo apresentaram carne mais magra, com menor teor de gordura, até 60 dias de experimento.