Marmoreados da Igreja São Luís dos Franceses (Lisboa): estado de conservação, caracterização das argamassas e da camada pictórica

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Ciências da Conservação

Evaluation of mechanical soft-abrasive blasting and chemical cleaning methods on alkyd-paint graffiti made on carbonate stones

In the context of this dissertation several studies were developed resulting in submission and publication “Evaluation of mechanical soft-abrasive blasting and chemical cleaning methods on alkyd-paint graffiti made on calcareous stones” to Journal of Cultural Heritage. (http://dx.doi.org/10.101 /j.culher.2014.10.004)

Synthesis, physical and magnetic properties of BaFe12O19/P(VDF-TrFE) multifunctional composites

Composite films with filler microparticles of Barium ferrite dispersed within P(VDF-TrFE) as polymeric matrix have been prepared by solvent evaporation. The lowest BaFO content of 1% wt acts as a small defect within the polymeric matrix, reducing the values of the dielectric and mechanical properties of the pure P(VDF-TrFE). For filler contents up to a 20%, the BaFO filler reinforces the matrix and measured properties increase their values. This trend is not followed by the electrical conductivity. We extended the study to fibers composed by BaFe12O19 microparticles in a PVDF matrix. Due to the big size of BaFO particles (1 micron in diameter), proper fabrication of the fiber shaped composites has not been achieved. We found that true BaFO content are always lower than nominal ones. Results are discussed in terms of the influence of size and morphology of the BaFO particles on the initial properties of the polymeric matrix.

Dielectric relaxation dynamics of high-temperature piezoelectric polyimide copolymers

Polyimide co-polymers have been prepared based on different diamines as co-monomers: a diamine without CN groups and a novel synthesized diamine with two CN groups prepared by polycondensation reaction followed by thermal cyclodehydration. Dielectric spectroscopy measurements were performed and the dielectric complex function, ac conductivity and electric modulus of the co-polymers were investigated as a function of CN group content in the frequency range from 0.1 Hz to 107 Hz at temperatures from 25 to 260 °C. For all samples and temperatures above 150ºC, the dielectric constant increases with increasing temperature due to increaseing conductivity. The α-relaxation is just detected for the sample without CN groups, being this relaxation overlapped by the electrical conductivity contributions in the remaining samples. For the copolymer samples and the polymer with CN groups an important Maxwell-Wagner-Sillars contribution is detected. The mechanisms responsible for the dielectric relaxation, conduction process and electric modulus response have been discussed as a function of the CN groups content present in the samples.

Energy harvesting device based on a metallic glass/PVDF magnetoelectric laminated composite

A flexible and low cost energy harvester device based on the magnetoelectric (ME) effect has been designed using Fe64Co17Si7B12 as amorphous magnetostrictive ribbons and PVDF as the piezoelectric element. Sandwich-type laminated composite of 3 cm long has been fabricated by gluing these ribbons to the PVDF with the Devcon 5 minute epoxy. Good power output and power density of 6.4 μW and 1.5 mW/cm3, respectively, have been obtained through a multiplier circuit. All values have been measured at the magnetomechanical resonance of the laminate. The effect of the length of the ME laminate on the power output has been also studied, exhibiting a decay as the length of the ME laminate does. Nevertheless, good performance of such device has been obtained for a 0.5 cm long device, working already at 337 KHz, within the low radio frequency (LRF) range.

Size effects on the magnetoelectric response on PVDF/Vitrovac 4040 laminate composites

Tri-layered and bi-layered magnetoelectric (ME) flexible composite structures of varying geometries and sizes consisting on magnetostrictive Vitrovac and piezoelectric poly(vinylidene fluoride) (PVDF) layers were fabricated by direct bonding. From the ME measurements it was determined that tri-layered composites structures (magnetostrictive-piezoelectric-magnetostrictive type), show a higher ME response (75 V.cm-1.Oe-1) than the bi-layer structure (66 V.cm 1.Oe-1). The ME voltage coefficient decreased with increasing longitudinal size aspect ratio between PVDF and Vitrovac layers (from 1.1 to 4.3), being observed a maximum ME voltage coefficient of 66 V.cm-1.Oe-1. It was also observed that the composite with the lowest transversal aspect ratio between PVDF and Vitrovac layers resulted in better ME performance than the structures with higher transversal size aspect ratios. It was further determined an intimate relation between the Vitrovac PVDF Area Area ratio and the ME response of the composites. When such ratio values approach 1, the ME response is the largest. Additionally the ME output value and magnetic field response was controlled by changing the number of Vitrovac layers, which allows the development of magnetic sensors and energy harvesting devices.

Induced magnetoelectric effect driven by magnetization in BaFe12O19 -/P(VDF-TrFE) composites

Films of BaFe12O19/P(VDF-TrFE) composites with 5, 10 and 20 %wt Barium ferrite content have been fabricated. BaFe12O19 microparticles have the shape of thin hexagonal platelets, the easy direction of magnetization remaining along the c axis, which is perpendicular to the plates. This fact allows for ferrite particles orientation in-plane and out-of-plane within the composite films, as confirmed by measured hysteresis loops. While the in-plane induced magnetoelectric effect (ME) is practically zero, these composite films show a good out-of-plane magnetoelectric effect. with maximum ME coupling coefficient changes of 3, 17 and 2 mV/cm.Oe for the 5, 10 and 20%wt Barium ferrite content films, respectively. We infer that this ME behavior appears as driven by the magnetization process arising when we applied the external magnetic field. We have also measured linear and reversible magnetoelectric effect for low applied bias field, when magnetization process is still reversible.

Proving the suitability of magnetoelectric stimuli for tissue engineering applications

A novel approach for tissue engineering applications based on the use of magnetoelectric materials is presented. This work proves that magnetoelectric Terfenol-D/poly(vinylidene fluoride-co-trifluoroethylene) composites are able to provide mechanical and electrical stimuli to MC3T3-E1 pre-osteoblast cells and that those stimuli can be remotely triggered by an applied magnetic field. Cell proliferation is enhanced up to 25% when cells are cultured under mechanical (up to 110 ppm) and electrical stimulation (up to 0.115 mV), showing that magnetoelectric cell stimulation is a novel and suitable approach for tissue engineering allowing magnetic, mechanical and electrical stimuli.

High performance screen printable lithium-ion battery cathode ink based on C-LiFePO4

Lithium-ion battery cathodes have been fabricated by screen-printing through the development of CLiFePO4 inks. It is shown that shear thinning polymer solutions in N-methyl-2-pyrrolidone (NMP) with Newtonian viscosity above 0.4 Pa s are the best binders for formulating a cathode paste with satisfactory film forming properties. The paste shows an elasticity of the order of 500 Pa and, after shear yielding, shows an apparent viscosity of the order of 3 Pa s for shear rates corresponding to those used during screen-printing. The screen-printed cathode produced with a thickness of 26 mm shows a homogeneous distribution of the active material, conductive additive and polymer binder. The total resistance and diffusion coefficient of the cathode are 450 V and 2.5 10 16cm2 s 1, respectively. The developed cathodes show an initial discharge capacity of 48.2 mAh g 1 at 5C and a discharge value of 39.8 mAh g 1 after 50 cycles. The capacity retention of 83% represents 23% of the theoretical value (charge and/or discharge process in twenty minutes), demonstrating the good performance of the battery. Thus, the developed C-LiFePO4 based inks allow to fabricate screen-printed cathodes suitable for printed lithium-ion batteries

Meiose em Tripsacum australe Cutler e Anderson (T. dactyhides subsp. hispidum Hitchcock)

Depois de uma breve introdução, mostrando a importância que o gênero Tripsacum desempenha hoje nos problemas da origem do milho, fizemos um estudo detalhado da meiose na nova espécie Tripsacum australe, descrita recentemente por CUTLER e ANDERSON (3) e espécie esta encontrada em estado selvagem na América do Sul. Todas as fases da meiose mostraram-se normais e o número cte cromosômios, facilmente determinado nas fases diacinese, metáfase I, metáfase II, é de 18 para a fase haplóide. Esta espécie não difere, quanto ao número de cromosômios, da forma diplóide Tripsacum dactyloide e da espécie Tripsacum floridanum, estudadas por LONGLEY (5). Segundo MANGELSDORF e REEVES (10) as formas de Tripsacum encontradas na América Central têm 72 cromosômios e são consideradas como autotetraplóides. Entretanto, no que se refere à presença de "knobs" nos cromosômios, esta espécie parece diferir da espécie estudada por LONGLEY (5). Tripsacum australe não apresenta "knobs" nas extremidades dos cromosômios e provavelmente também nas outras regiões pois as figuras que puderam ser examinadas não mostraram essa estrutura. Segundo MANGELSDORF e REEVES (10) os "knobs" presentes no milho teriam vindo de Tripsacum, por meio de cruzamento entre estes dois gêneros. Assim sendo, os tipos de milho cultivados próximos ao centro de distribuição das espécies de Tripsacum até então conhecidas, e que é a região da América Central, principalmente o México, deveriam se apresentar bastante contaminados por este gênero e apresentariam mais "knobs" do que aqueles tipos de milho cultivados ionge da referida região. Observações de vários autores (6, 7, 9, 20, 11 e 12) confirmam esta hipótese, inclusive aquelas realizadas por um dos autores deste trabalho (Graner, não publicado) em material sul-americano. Tendo sido encontrada agora esta nova espécie de Tripsacum na América do Sul, aparentemente sem "knobs", torna-se interessante verificar se ela não poderia ter contribuido para o estabelecimento das formas de milho sem "knobs" encontradas na América do Sul. Cruzamentos entre milho e Tripsacum australe foram realizados por um dos autores (Addison), não lendo porém produzido sementes. Outras pesuisas tornam-se então necessárias afim de que se possa tirar conclusões a respeito de tão importante assunto.

A collection of birds from the Ivory Coast [by] Melvin A. Traylor and Daniel Parelius.

v.51:no.7(1967)

A la recerca de l'occità: Tres dialectes del nord

Treball de recerca realitzat per un alumne d'ensenyament secundari i guardonat amb un Premi CIRIT per fomentar l'esperit cientí­fic del Jovent l'any 2009. El tema d'aquest treball és la llengua occitana, alhora dividit en un estudi sociolingüístic (situació actual de l'occità) i en un de dialectològic (estudi fonètic i morfològic del nord-occità). Tot seguit d'una introducció en què es parla de la relació de l'autor del present estudi amb el món de l'occià al llarg de quatre anys, es presenta la situació de la llengua tenint sempre present el seu context: història, estats on és pròpia, situació d'aquesta en les diferents regions en què es parla, qüestió del nom, problemàtica de l'estandardització, etc.. Es tracta de la greu situació en què es troba als tres estats en què és parlada, tot intentant d'explicar-ne els motius. A més a més, es fa referència a les distintes tendències quant a la normativització: estandardització rígida o flexible a la mena de l'''euskara batua'' o basc unificat. D'altra banda, en consonància amb l'objectiu de la preservació i valoració de la riquesa dialectal de l'occità, es fa una presentació sobretot fonètica (tot i que també es fa un tastet de morfologia) dels tres dialectes nord-occitans (alvernès, llemosí i vivaroalpí), que són els menys coneguts i estudiats, la qual cosa ha permès de ratificar la unitat del nord-occità.

Integración de políticas medio ambientales: Transformaciones institucionales en España

La Integración de la Políticas Ambientales (IPA) consiste en la incorporación de los objetivos ambientales en todos los estadios de elaboración e implementación de las políticas no ambientales (o sectoriales), con un reconocimiento específico de dicho objetivo como principio director de la programación y la puesta en práctica. Se complementa con la previsión de las consecuencias ambientales mediante una evaluación de conjunto de la política con objeto de minimizar las contradicciones entre las políticas ambientales y no ambientales dando prioridad a las primeras. La naturaleza transversal de la IPA no se ajusta a la forma tradicional de gobernanza jerárquica basada en la autoridad del Estado, la diferenciación sectorial, y los instrumentos típicos de dirección y control. Por ello, no es extraño que la IPA se encuentre a menudo asociada a los llamados "nuevos modos de gobernanza". Esta tesis propone analizar empíricamente el estado de la cuestión en España con respecto a la Integración de la política ambiental , tanto a nivel estatal como autonómico (Cataluña, País Vasco), yendo más allá de los compromisos políticos a favor de un mayor grado de integración de los factores ambientales en las demás políticas. En particular, los ámbitos de investigación seleccionados para esta finalidad son el de las políticas de mitigación de las causas y los efectos del cambio climático, y las políticas de desarrollo sostenible. En términos de ‘variable independiente’ La hipótesis que se quiere comprobar es que la acción llevada a cabo por la Unión Europea ha generado profundos cambios en las estructuras de las instituciones mencionadas y en los procesos de elaboración y implementación de determinadas políticas (energía y transporte) así como en las relaciones entre sectores de la administración pública y entre el sector público y el privado.

¿Elecciones en 2009? Avances y obstáculos de la construcción de paz en Costa de Marfil

Tres meses de conflicto armado en Côte d'Ivoire en 2002 acabaron con la división del país en dos regiones, separadas por una línea de separación controlada por las francesas Forces Licorne. El proceso de paz se alargó en el tiempo y se caracterizó por una falta de confianza mutua y por la inmovilidad política. Estos hechos desembocaron en una situación de impasse y en la permanencia de Laurent Gbagbo en la presidencia del país. Además, los diferentes acuerdos políticos no ayudaron al proceso de construcción de paz, ya que no trataban algunos de los problemas principales del país, como la propiedad de las tierras y la identidad. Este documento de trabajo aspira, en primer lugar, a analizar los hechos principales y las causas que originaron el conflicto desde el golpe de estado de 2002. En segundo lugar, el documento analiza el proceso de paz y señala los elementos clave del Acuerdo de Paz de Ouagadougou (2007): la creación de una estructura de fuerzas armadas nueva y única, así como la identificación de la población y la convocatoria de elecciones. El objetivo principal es proporcionar una herramienta de trabajo al Institut Català Internacional per la Pau (ICIP) para enviar una futura comisión de observación electoral a este país africano.