Selective Ortho-Hydroxylation–Defluorination of 2-Fluorophenolates with a Bis(m-oxo)dicopper(III) Species

The bis(mu-oxo) dicopper(III) species [Cu-III 2(mu-O)(2)(m-XYLMeAN)](2+) (1) promotes the electrophilic ortho-hydroxylation-defluorination of 2-fluorophenolates to give the corresponding catechols, a reaction that is not accomplishable with a (eta(2) : eta(2)-O-2) dicopper(II) complex. Isotopic labeling studies show that the incoming oxygen atom originates from the bis(mu-oxo) unit. Ortho-hydroxylation-defluorination occurs selectively in intramolecular competition with other ortho-substituents such as chlorine or bromine

An Engineering Solution for using Coarse Meshes in the Simulation of Delamination with Cohesive Zone Models

This paper presents a methodology to determine the parameters used in the simulation of delamination in composite materials using decohesion finite elements. A closed-form expression is developed to define the stiffness of the cohesive layer. A novel procedure that allows the use of coarser meshes of decohesion elements in large-scale computations is proposed. The procedure ensures that the energy dissipated by the fracture process is correctly computed. It is shown that coarse-meshed models defined using the approach proposed here yield the same results as the models with finer meshes normally used in the simulation of fracture processes

Approximate solution to the speed of spreading viruses

Recently, it has been shown that the speed of virus infections can be explained by time-delayed reactiondiffusion [J. Fort and V. Me´ndez, Phys. Rev. Lett. 89, 178101 (2002)], but no analytical solutions were found. Here we derive formulas for the front speed, valid in appropriate limits. We also integrate numerically the evolution equations of the system. There is good agreement with both numerical and experimental speeds

Synthesis and antiprotozoal activity of oligomethylene- and p-phenylene-bis(methylene)-linked bis(+)-huprines

We have synthesized a series of dimers of (+)-(7R,11R)-huprine Y and evaluated their activity against Trypanosoma brucei, Plasmodium falciparum, rat myoblast L6 cells and human acetylcholinesterase (hAChE), and their brain permeability. Most dimers have more potent and selective trypanocidal activity than huprine Y and are brain permeable, but they are devoid of antimalarial activity and remain active against hAChE. Lead optimization will focus on identifying compounds with a more favourable trypanocidal/anticholinesterase activity ratio.

Synthesis and antiprotozoal activity of oligomethylene- and p-phenylene-bis(methylene)-linked bis(+)-huprines

We have synthesized a series of dimers of (+)-(7R,11R)-huprine Y and evaluated their activity against Trypanosoma brucei, Plasmodium falciparum, rat myoblast L6 cells and human acetylcholinesterase (hAChE), and their brain permeability. Most dimers have more potent and selective trypanocidal activity than huprine Y and are brain permeable, but they are devoid of antimalarial activity and remain active against hAChE. Lead optimization will focus on identifying compounds with a more favourable trypanocidal/anticholinesterase activity ratio.

Kapillaarielektroforeesin soveltaminen uuttofaasin koostumuksen analysointiin

Työn tarkoituksena oli löytää kapillaarielektroforeesimenetelmä (CE), joka soveltuisi metallien neste-nesteuutossa käytettävien orgaanisten uuttofaasien koostumuksen analysointiin. Kapillaarielektroforeesissa käytetyn elektrolyyttiliuoksen analyytti-kohtaista optimointia ei tässä työssä tehty, vaan liikkeelle lähdettiin fenoleille tarkoitetulla menetelmällä. Tarkasteltavia uuttoreagenssiryhmiä olivat hydroksi-oksiimit sekä fosfiinihappo- ja fosforihappopohjaiset reagenssit. Tutkittavia kaupallisia laimentimia olivat Orfom SX 11 ja Shellsol D70. Lisäksi tutkittiin kahta modifiointiainetta, TOPOa (tri-n-oktyylifosfiinioksidi) ja TXIB:tä (2,2,4-trimetyyli-1,3-pentaanidiolidi-isobutyraatti). Työssä tavoiteltiin kapillaarielektroforeesin hyötyjä erityisesti hydrometallurgisessa teollisuudessa. Suurimpana hyötynä ennakoitiin mahdollisuus analysoida suuria molekyylejä, kuten uuttoreagenssi-metallikomplekseja, joita ei pystytä analysoimaan kaasukromatografilla (GC). Näytteet voidaan myös analysoida ilman hidasta ja usein ei-kvantitatiivista derivatisointia. Kirjallisuudesta ei löytynyt aiempia artikkeleita CE:n soveltamisesta kyseisille aiheille. Kapillaarielektroforeesianalyyseissa pystyttiin esimerkiksi havaitsemaan hydroksi-oksiimin kuparikompleksi orgaanisessa faasissa. Seulonta-ajoissa yleisenä ongelmana oli kuitenkin tulosten heikko toistettavuus. Kapillaari-elektro-foreesi-menetelmä tarjoaa selvästi mahdollisuuksia tulevaisuudessa, mutta vielä sillä ei päästy luotettavaan toistoon sähkökentän häiriöiden ja elektrolyyttiliuoksen riittämättömän optimoinnin vuoksi. Lisäksi teollisissa olosuhteissa käytetyille autenttisille hydroksioksiimi- ja fosfiinihapponäytteille tehtiin perinteisiä kaasukromatografia-analyysejä, joiden perusteella voitiin nähdä uuttofaasin koostumuksen muuttuneen prosessissa. Hapettuminen sekä eri hydrolyysireaktiot ovat tärkeimmät syyt reagenssien ja laimentimien muuttumiselle. Näitä hajoamistuotteita ei tässä työssä onnistuttu analysoimaan kapillaarielektroforeesilla.

Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Extração líquido-líquido de ferro(III) e titânio(IV) pelo ácido bis-(2-etil-hexil) fosfórico (D2EHPA) em meio de ácido sulfúrico

This work presents a study on the separation of Fe(III) and Ti(IV) from sulfuric acid leaching solutions of ilmenite (FeTiO3) using liquid-liquid extraction with D2EHPA in n-dodecane as extracting agent. The distribution coefficients (K D) of the elements related to free acidity and concentration of Fe(III) and Ti(IV) were determined. Free acidity was changed from 3x10-2 to 11.88 mol L-1 and D2EHPA concentration was fixed at 1.5 mol L-1. Recovery of final products as well as recycling of wastes generated in the process were also investigated. The LLE process as a feasible alternative to obtain high-purity TiO2.

Estudos de relações estrutura-atividade quantitativas (QSAR) de bis-benzamidinas com atividade antifúngica

This paper describes 2D-QSAR and 3D-QSAR studies against Candida albicans and Cryptococcus neofarmans for a set of 20 bisbenzamidines. In the studies of 2D-QSAR with C. albicans it was obtained a correlation between log MIC-1 and lipolo component-Z (r² = 0.68; Q² = 0.51). In the case of C. neofarmans a correlation between log MIC-1 and lipolo component-Z and of Balaban index (r² = 0.85; Q² = 0.6) was obtained. 3D-QSAR studies using CoMFA showed that the steric fields contributed more to the predicted activities for Candida albicans (94.9%) and Cryptococcus neofarmans (97.9%).

Determination of traces of nitrate in water samples using spectrophotometric method after its preconcentration on microcrystalline naphthalene

Nitrate is quantitatively retained with 2,6-bis(4-methoxyphenyl)-4-phenyl pyrylium perchlorate (PPP) on microcrystalline naphthalene in the pH range of 6.5-9.0 from a large volume of aqueous solutions of various samples. The method was based on the complexation between PPP and nitrate and then, extraction of the resulted complex from aqueous solution by microcrystalline naphthalene. The solid mass consisting of the nitrate complex and naphthalene was then dissolved in dimethyl formamide (DMF) and absorption of the resulted solution was obtained at 328 nm. The linear calibration range for the determination of nitrate was 15-135 μg L-1 with the detection limit of 10 μg L-1.

Synthesis and antifungal activity of halogenated aromatic bis-γ-lactones analogous to avenaciolide

Here we describe the total syntheses and characterization by elemental analyses, infrared and NMR spectroscopy of three new compounds analogous to avenaciolide, a bis-γ-lactone isolated from Aspergillus avenaceus that possesses antifungal activity, where the octyl group of the natural product was replaced by aromatic groups containing chlorine and fluorine atoms. The effects of the avenaciolide, the novel compounds and their synthetic precursors on mycelia development and conidia germination of Colletotrichum gloeosporioides and Fusarium solani were evaluated in vitro. The title compounds were almost as active as avenaciolide. The absolute structures of the chlorinated analogs were determined by X-ray diffraction analysis.

Investigating the spontaneous formation of SDS micelle in aqueous solution using a coarse-grained force field

A 1µs Molecular Dynamic simulation was performed with a realistic model system of Sodium Dodecyl Sulfate (SDS) micelles in aqueous solution, comprising of 360 DS-, 360 Na+ and 90000 water particles. After 300 ns three different micellar shapes and sizes 41, 68 and 95 monomers, were observed. The process led to stabilization in the total number of SDS clusters and an increase in the micellar radius to 2.23 nm, in agreement with experimental results. An important conclusion, is be aware that simulations employed in one aggregate, should be considered as a constraint. Size and shape distribution must be analyzed.

Solution thermodynamics of methocarbamol in some ethanol + water mixtures

Apparent thermodynamic functions, Gibbs energy, enthalpy and entropy of solution and mixing, for methocarbamol in ethanol + water mixtures, were evaluated from solubility data determined at temperatures from 293.15 K to 313.15 K and from calorimetric values of drug fusion. The drug solubility was greatest in the mixtures with 0.70 or 0.80 mass fraction of ethanol and lowest in neat water across all temperatures studied. Non-linear enthalpy-entropy compensation was found for the dissolution processes. Accordingly, solution enthalpy drives the respective processes in almost all the solvent systems analyzed.

Syntheses, characterization and antifungal activity of tris(1,10-phenanthroline)iron(ii) bis(n-r-sulfonyldithiocarbimate)zincate(ii)

Four new compounds with the general formula [Fe(phen)3][Zn(RSO2N=CS2)2], where phen = 1,10-phenanthroline, R = 4-FC6H4 (1), 4-ClC6H4 (2), 4-BrC6H4 (3) and 4-IC6H4 (4), respectively, were obtained by the reaction of the appropriate potassium N-R-sulfonyldithiocarbimate (RSO2N=CS2K2) and tris(1,10-phenanthroline)iron(II) sulfate, with zinc(II) acetate dihydrate in dimethylformamide. The elemental analyses and the IR data were consistent with the formation of the expected complexes salts. The ¹H and 13C NMR spectra showed the signals for the cationic iron(II) complex and dithiocarbimate moieties. The molar conductance data were consistent with the 1:1 cation:anion complexes in 1-4. The antifungal activities of the compounds were tested in vitro against Candida albicans, Candida tropicalis and Colletotrichum gloeosporioides.

Sodium dodecyl sulfate coated γ-alumina support modified by a new Schiff base for solid phase extraction and flame-AAS determination of lead and copper ions

A simple and fast approach for solid phase extraction is herein described, and used to determine trace amounts of Pb2+ and Cu2+ metal ions. The solid phase support is sodium dodecyl sulfate (SDS)-coated γ-alumina modified with bis(2-hydroxy acetophenone)-1,6-hexanediimine (BHAH) ligand. The adsorbed ions were stripped from the solid phase by 6 mL of 4 M nitric acid as eluent. The eluting solution was analyzed by flame atomic absorption spectrometry (FAAS). The sorption recovery of metal ions was investigated with regard to the effects of pH, amount of ligand, γ-alumina and surfactant and the amount and type of eluent. Complexation of BHAH with Pb2+ or Cu2+ ions was examined via spectrophotometry using the HypSpec program. The detection limit for Cu2+ was 7.9 µg L-1 with a relative standard deviation of 1.67%, while that for Pb2+ was 6.4 µg L-1 with a relative standard deviation of 1.64%. A preconcentration factor of 100 was achieved for these ions. The method was successfully applied to determine analyte concentrations in samples of liver, parsley, cabbage, and water.