Analysis of mode competition in a monolithic master- oscillator power‐amplifier emitting at 1.5 μm

The optical and radio-frequency spectra of a monolithic master-oscillator power-amplifier emitting at 1.5 ?m have been analyzed in a wide range of steady-state injection conditions. The analysis of the spectral maps reveals that, under low injection current of the master oscillator, the device operates in two essentially different operation modes depending on the current injected into the amplifier section. The regular operation mode with predominance of the master oscillator alternates with lasing of the compound cavity modes allowed by the residual reflectance of the amplifier front facet. The quasi-periodic occurrence of these two regimes as a function of the amplifier current has been consistently interpreted in terms of a thermally tuned competition between the modes of the master oscillator and the compound cavity modes.

The counteractive effect of the sensor housing on the unit sensitivity across a series of dynamic temperature profiles.

The advantages of wireless sensing implemented on the cold chain of fresh products are well known. These sensor systems consist of a combination of delicate internal electronic circuitry enclosed in a special housing unit. Manufacturers however are presented with the challenge that the housing required to withstand the harsh environment in which the sensors are being used all too often take from the functionality of the sensor. Therefore the target of this study is to determine the dynamic behavior and the counteractive effects of the sensor housing on temperature recording accuracy in the wireless nodes of Wireless Sensor Network (WSN) and Radio Frequency Identification (RFID) semi-passive tags. Two kind of semi-passive Turbo Tags were used (T700 and T702-B), which consisted of sensors with and without a cover, and two kind of WSN nodes, IRIS (sensors Intersema and Sensirion soldered in the motherboard) and NLAZA (Sensirion in a cable and soldered to the motherboard). To recreate the temperature profiles the devices were rotated between a cold room(5 ºC) through a ambient room(23 ºC) to a heated environment (35ºC) and vice versa. Analysis revealed the differences between housing and no housing are 308.22s to 21.99s respectively in the step from 5 to 35 ºC. As is demonstrated in these experiments the influence of the housing significantly hinders sensor accuracy.

Comparativa de las medidas de emisiones electromagnéticas en las normativas europea y americana para teléfonos duales

El objetivo del presente Proyecto Fin de Grado es la realización de una comparativa de los resultados obtenidos en las medidas de SAR (tasa de absorción específica) y potencia utilizando la normativa europea CENELEC (basada en la del IEC) y la americana FCC (basada en la del IEEE) para distintos dispositivos móviles duales. En primer lugar se ha realizado el estudio de sus características de potencia y de SAR, viendo la variación que hay con respecto a las distintas normativas y rangos de frecuencias. En algunos casos, aunque funcionan sin problema alguno en las diferentes bandas, la diferencia de niveles de emisiones obtenidos en las diferentes bandas puede ser notable. Como se ha comentado al comienzo, se han utilizado diferentes dispositivos duales y se realizaron en ellos las medidas pertinentes utilizando las diferentes normativas y el procedimiento indicado en cada una de ellas. Para observar las diferencias concretas que pudieran existir al utilizar las diferentes normativas, las medidas se han realizado en todas las bandas de funcionamiento del dispositivo y para cada una de ellas se han aplicado las diferentes normativas. Con esto se pretende evaluar si pudiera existir alguna discrepancia en los dispositivos que tienen el certificado de conformidad para una norma concreta cuando se utiliza en otra banda que no es exactamente la banda de utilización de esa norma. En resumen, se quería comprobar que un dispositivo que está certificado con la norma de una región, por ejemplo Europa (900 y 1800 MHz), también cumple si se utiliza en otra región, por ejemplo América (850 y 1900 MHz). La realización práctica del presente PFG se ha hecho en las instalaciones del Laboratorio de Radiofrecuencia de la Secretaría de Estado de Telecomunicación y para la Sociedad de la Información ubicado en El Casar (Guadalajara). En concreto se utilizó el robot articulado movible DASY4 y el software para su control DASY 52.8, disponible en el “banco de medida de Campos Electromagnéticos (Sala de SAR)”. La duración estimada del presente PFG ha sido aproximadamente de cuatro meses. Para llevar a cabo el presente PFG, se dispuso de todo tipo de material y recursos puestos a disposición por el Ministerio de Industria, Turismo y Comercio en el propio laboratorio, así como de los distintos terminales móviles duales con los que se realizaron las medidas pertinentes. Como bibliografía básica se han utilizado las diferentes normas indicadas anteriormente, es decir la norma europea CENELEC (basada en la del IEC) y la americana FCC (basada en la del IEEE), así como manuales de los equipos implicados en el bando de medida de SAR: analizadores de redes, robot articulado y software de control, así como el resto de dispositivos utilizados en las medidas. ABSTRACT. The goal of this Final Degree Project is to perform a comparison of the results obtained in SAR measurements (specific absorption rate) and power using the European standards CENELEC (based on IEC Regulation) and the American FCC (based on IEEE Regulation) to different mobile dual devices. If first place it was made the study of its power and SAR features, seeing that there is shift with respect to the different standards and frequency ranges. In some cases, although they work without any problem in different bands, the difference in levels of emissions obtained in the different bands can be significant. As mentioned at the beginning, different dual devices were used and relevant measurements were taken from them using the different standards and the procedure in each one of them. To see the specific differences that may exist when using the different standards, the measurements were made in all bands of the device operation and to each one it has been applied in the different standards. This attempted to assess whether there could be some discrepancy in the devices that have the certificate of compliance to a specify standard when used in another band that is not exactly the used band of this standard. To sum up, it was required to verify that a device which is certified to the standard of a region, for example (900 and 1800 MHz), also verifies if it is used in another region, for example America (850 and 1900 MHz). The practical realization of this Final Degree Project was made in the facilities of the Radio Frequency Laboratory of the Ministry of State for Telecommunications and the Information Society located in El Casar (Guadalajara). Specifically, the movable articulated robot DASY4 was used and the control software DASY 52.8, available in the “Measure Electromagnetic Field testbench (SAR room)”. The duration of this Final Degree Project has benn about four months. To carry out the present project, all kinds of materials and resources were provided by the Ministry of Industry, Tourism and Trade in its own laboratory, as well as the different mobile dual terminals with which relevant measurements were made. As basic references the different standards indicated above has been used, that is to say the European standard CENELEC (based on IEC standard) and the American FCC (based on IEEE standard), as well as the equipment manuals involved in the SAR measure testbench: network analyzers, articulated robot and control software, as well as the rest of the devices used in the measurements.

Advanced Characterisation of a Coffee Fermenting Tank by Multi-distributed Wireless Sensors: Spatial Interpolation and Phase Space Graphs

The fermentation stage is considered to be one of the critical steps in coffee processing due to its impact on the final quality of the product. The objective of this work is to characterise the temperature gradients in a fermentation tank by multi-distributed, low-cost and autonomous wireless sensors (23 semi-passive TurboTag® radio-frequency identifier (RFID) temperature loggers). Spatial interpolation in polar coordinates and an innovative methodology based on phase space diagrams are used. A real coffee fermentation process was supervised in the Cauca region (Colombia) with sensors submerged directly in the fermenting mass, leading to a 4.6 °C temperature range within the fermentation process. Spatial interpolation shows a maximum instant radial temperature gradient of 0.1 °C/cm from the centre to the perimeter of the tank and a vertical temperature gradient of 0.25 °C/cm for sensors with equal polar coordinates. The combination of spatial interpolation and phase space graphs consistently enables the identification of five local behaviours during fermentation (hot and cold spots).

Contribución a la localización en interiores basada en comunicaciones inalámbricas

Determinar con buena precisión la posición en la que se encuentra un terminal móvil, cuando éste se halla inmerso en un entorno de interior (centros comerciales, edificios de oficinas, aeropuertos, estaciones, túneles, etc), es el pilar básico sobre el que se sustentan un gran número de aplicaciones y servicios. Muchos de esos servicios se encuentran ya disponibles en entornos de exterior, aunque los entornos de interior se prestan a otros servicios específicos para ellos. Ese número, sin embargo, podría ser significativamente mayor de lo que actualmente es, si no fuera necesaria una costosa infraestructura para llevar a cabo el posicionamiento con la precisión adecuada a cada uno de los hipotéticos servicios. O, igualmente, si la citada infraestructura pudiera tener otros usos distintos, además del relacionado con el posicionamiento. La usabilidad de la misma infraestructura para otros fines distintos ofrecería la oportunidad de que la misma estuviera ya presente en las diferentes localizaciones, porque ha sido previamente desplegada para esos otros usos; o bien facilitaría su despliegue, porque el coste de esa operación ofreciera un mayor retorno de usabilidad para quien lo realiza. Las tecnologías inalámbricas de comunicaciones basadas en radiofrecuencia, ya en uso para las comunicaciones de voz y datos (móviles, WLAN, etc), cumplen el requisito anteriormente indicado y, por tanto, facilitarían el crecimiento de las aplicaciones y servicios basados en el posicionamiento, en el caso de poderse emplear para ello. Sin embargo, determinar la posición con el nivel de precisión adecuado mediante el uso de estas tecnologías, es un importante reto hoy en día. El presente trabajo pretende aportar avances significativos en este campo. A lo largo del mismo se llevará a cabo, en primer lugar, un estudio de los principales algoritmos y técnicas auxiliares de posicionamiento aplicables en entornos de interior. La revisión se centrará en aquellos que sean aptos tanto para tecnologías móviles de última generación como para entornos WLAN. Con ello, se pretende poner de relieve las ventajas e inconvenientes de cada uno de estos algoritmos, teniendo como motivación final su aplicabilidad tanto al mundo de las redes móviles 3G y 4G (en especial a las femtoceldas y small-cells LTE) como al indicado entorno WLAN; y teniendo siempre presente que el objetivo último es que vayan a ser usados en interiores. La principal conclusión de esa revisión es que las técnicas de triangulación, comúnmente empleadas para realizar la localización en entornos de exterior, se muestran inútiles en los entornos de interior, debido a efectos adversos propios de este tipo de entornos como la pérdida de visión directa o los caminos múltiples en el recorrido de la señal. Los métodos de huella radioeléctrica, más conocidos bajo el término inglés “fingerprinting”, que se basan en la comparación de los valores de potencia de señal que se están recibiendo en el momento de llevar a cabo el posicionamiento por un terminal móvil, frente a los valores registrados en un mapa radio de potencias, elaborado durante una fase inicial de calibración, aparecen como los mejores de entre los posibles para los escenarios de interior. Sin embargo, estos sistemas se ven también afectados por otros problemas, como por ejemplo los importantes trabajos a realizar para ponerlos en marcha, y la variabilidad del canal. Frente a ellos, en el presente trabajo se presentan dos contribuciones originales para mejorar los sistemas basados en los métodos fingerprinting. La primera de esas contribuciones describe un método para determinar, de manera sencilla, las características básicas del sistema a nivel del número de muestras necesarias para crear el mapa radio de la huella radioeléctrica de referencia, junto al número mínimo de emisores de radiofrecuencia que habrá que desplegar; todo ello, a partir de unos requerimientos iniciales relacionados con el error y la precisión buscados en el posicionamiento a realizar, a los que uniremos los datos correspondientes a las dimensiones y realidad física del entorno. De esa forma, se establecen unas pautas iniciales a la hora de dimensionar el sistema, y se combaten los efectos negativos que, sobre el coste o el rendimiento del sistema en su conjunto, son debidos a un despliegue ineficiente de los emisores de radiofrecuencia y de los puntos de captura de su huella. La segunda contribución incrementa la precisión resultante del sistema en tiempo real, gracias a una técnica de recalibración automática del mapa radio de potencias. Esta técnica tiene en cuenta las medidas reportadas continuamente por unos pocos puntos de referencia estáticos, estratégicamente distribuidos en el entorno, para recalcular y actualizar las potencias registradas en el mapa radio. Un beneficio adicional a nivel operativo de la citada técnica, es la prolongación del tiempo de usabilidad fiable del sistema, bajando la frecuencia en la que se requiere volver a capturar el mapa radio de potencias completo. Las mejoras anteriormente citadas serán de aplicación directa en la mejora de los mecanismos de posicionamiento en interiores basados en la infraestructura inalámbrica de comunicaciones de voz y datos. A partir de ahí, esa mejora será extensible y de aplicabilidad sobre los servicios de localización (conocimiento personal del lugar donde uno mismo se encuentra), monitorización (conocimiento por terceros del citado lugar) y seguimiento (monitorización prolongada en el tiempo), ya que todos ellas toman como base un correcto posicionamiento para un adecuado desempeño. ABSTRACT To find the position where a mobile is located with good accuracy, when it is immersed in an indoor environment (shopping centers, office buildings, airports, stations, tunnels, etc.), is the cornerstone on which a large number of applications and services are supported. Many of these services are already available in outdoor environments, although the indoor environments are suitable for other services that are specific for it. That number, however, could be significantly higher than now, if an expensive infrastructure were not required to perform the positioning service with adequate precision, for each one of the hypothetical services. Or, equally, whether that infrastructure may have other different uses beyond the ones associated with positioning. The usability of the same infrastructure for purposes other than positioning could give the opportunity of having it already available in the different locations, because it was previously deployed for these other uses; or facilitate its deployment, because the cost of that operation would offer a higher return on usability for the deployer. Wireless technologies based on radio communications, already in use for voice and data communications (mobile, WLAN, etc), meet the requirement of additional usability and, therefore, could facilitate the growth of applications and services based on positioning, in the case of being able to use it. However, determining the position with the appropriate degree of accuracy using these technologies is a major challenge today. This paper provides significant advances in this field. Along this work, a study about the main algorithms and auxiliar techniques related with indoor positioning will be initially carried out. The review will be focused in those that are suitable to be used with both last generation mobile technologies and WLAN environments. By doing this, it is tried to highlight the advantages and disadvantages of each one of these algorithms, having as final motivation their applicability both in the world of 3G and 4G mobile networks (especially in femtocells and small-cells of LTE) and in the WLAN world; and having always in mind that the final aim is to use it in indoor environments. The main conclusion of that review is that triangulation techniques, commonly used for localization in outdoor environments, are useless in indoor environments due to adverse effects of such environments as loss of sight or multipaths. Triangulation techniques used for external locations are useless due to adverse effects like the lack of line of sight or multipath. Fingerprinting methods, based on the comparison of Received Signal Strength values measured by the mobile phone with a radio map of RSSI Recorded during the calibration phase, arise as the best methods for indoor scenarios. However, these systems are also affected by other problems, for example the important load of tasks to be done to have the system ready to work, and the variability of the channel. In front of them, in this paper we present two original contributions to improve the fingerprinting methods based systems. The first one of these contributions describes a method for find, in a simple way, the basic characteristics of the system at the level of the number of samples needed to create the radio map inside the referenced fingerprint, and also by the minimum number of radio frequency emitters that are needed to be deployed; and both of them coming from some initial requirements for the system related to the error and accuracy in positioning wanted to have, which it will be joined the data corresponding to the dimensions and physical reality of the environment. Thus, some initial guidelines when dimensioning the system will be in place, and the negative effects into the cost or into the performance of the whole system, due to an inefficient deployment of the radio frequency emitters and of the radio map capture points, will be minimized. The second contribution increases the resulting accuracy of the system when working in real time, thanks to a technique of automatic recalibration of the power measurements stored in the radio map. This technique takes into account the continuous measures reported by a few static reference points, strategically distributed in the environment, to recalculate and update the measurements stored into the map radio. An additional benefit at operational level of such technique, is the extension of the reliable time of the system, decreasing the periodicity required to recapture the radio map within full measurements. The above mentioned improvements are directly applicable to improve indoor positioning mechanisms based on voice and data wireless communications infrastructure. From there, that improvement will be also extensible and applicable to location services (personal knowledge of the location where oneself is), monitoring (knowledge by other people of your location) and monitoring (prolonged monitoring over time) as all of them are based in a correct positioning for proper performance.

Temperature, ordering, and equilibrium with time-dependent confining forces

The concepts of temperature and equilibrium are not well defined in systems of particles with time-varying external forces. An example is a radio frequency ion trap, with the ions laser cooled into an ordered solid, characteristic of sub-mK temperatures, whereas the kinetic energies associated with the fast coherent motion in the trap are up to 7 orders of magnitude higher. Simulations with 1,000 ions reach equilibrium between the degrees of freedom when only aperiodic displacements (secular motion) are considered. The coupling of the periodic driven motion associated with the confinement to the nonperiodic random motion of the ions is very small at low temperatures and increases quadratically with temperature.

Signal Processing Techniques for Chipless UWB RFID Thermal Threshold Detector Detection.

This letter presents signal processing techniques to detect a passive thermal threshold detector based on a chipless time-domain ultrawideband (UWB) radio frequency identification (RFID) tag. The tag is composed by a UWB antenna connected to a transmission line, in turn loaded with a biomorphic thermal switch. The working principle consists of detecting the impedance change of the thermal switch. This change occurs when the temperature exceeds a threshold. A UWB radar is used as the reader. The difference between the actual time sample and a reference signal obtained from the averaging of previous samples is used to determine the switch transition and to mitigate the interferences derived from clutter reflections. A gain compensation function is applied to equalize the attenuation due to propagation loss. An improved method based on the continuous wavelet transform with Morlet wavelet is used to overcome detection problems associated to a low signal-to-noise ratio at the receiver. The average delay profile is used to detect the tag delay. Experimental measurements up to 5 m are obtained.

Controle de uma plataforma inercial estabilizada com três graus de liberdade.

Esta dissertação apresenta o desenvolvimento de uma plataforma inercial autônoma com três graus de liberdade para aplicação em estabilização de sensores - por exemplo, gravimétricos estacionários e embarcados - podendo ser utilizada também para estabilização de câmeras. O sistema é formado pela Unidade de Medida Inercial, IMU, desenvolvida utilizando um sensor micro eletromecânico, MEMS - que possui acelerômetro, giroscópio e magnetômetros nos três eixos de orientação - e um microcontrolador para aquisição, processamento e envio dos dados ao sistema de controle e aquisição de dados. Para controle dos ângulos de inclinação e orientação da plataforma, foi implementado um controlador PID digital utilizando microcontrolador. Este recebe os dados da IMU e fornece os sinais de controle utilizando as saídas PWM que acionam os motores, os quais controlam a posição da plataforma. Para monitoramento da plataforma foi desenvolvido um programa para aquisição de dados em tempo real em ambiente Matlab, por meio do qual se pode visualizar e gravar os sinais da IMU, os ângulos de inclinação e a velocidade angular. Testou-se um sistema de transmissão de dados por rádio frequência entre a IMU e o sistema de aquisição de dados e controle para avaliar a possibilidade da não utilização de slip rings ou fios entre o eixo de rotação e os quadros da plataforma. Entretanto, verificou-se a inviabilidade da transmissão em razão da baixa velocidade de transmissão e dos ruídos captados pelo receptor de rádio frequência durante osmovimentos da plataforma. Sendo assim, dois pares de fios trançados foram utilizados fios para conectar o sensor inercial ao sistema de aquisição e processamento.

Filmes de óxido de zinco e nitreto de zinco depositados por magnetron sputtering com diferentes pressões de argônio, oxigênio e nitrogênio.

O óxido de zinco é um material semicondutor que apresenta alta transparência óptica no espectro visível, alta energia de ligação de éxcitons e piezoeletricidade. Por suas propriedades, ele é utilizado na área de sensores, eletrodos transparentes e dispositivos optoeletrônicos. No entanto, sua utilização ainda é limitada pela dificuldade de obtenção de condutividade tipo p, cujo principal dopante é o nitrogênio, devido à assimetria de dopagem ocasionada por defeitos intrínsecos do material, dopagem em valências diferentes das esperadas e formação de níveis de aceitadores profundos na banda proibida. A aplicação em dispositivos piezoelétricos também exige alta resistividade e ótimas propriedades cristalinas. Muitos processos de deposição estabelecidos hoje ainda utilizam altas temperaturas, o que impede sua deposição sobre superfícies ou substratos sensíveis a altas temperaturas. O objetivo deste trabalho é desenvolver técnicas de deposição de filmes de ZnO, principalmente em baixas temperaturas ( 100°C), pelo método de magnetron sputtering de rádio frequência, para avaliar a influência dos gases de processo nas características estruturais, estequiométricas, elétricas e ópticas dos filmes. Para isso, foram obtidos filmes utilizando pressão total de argônio, e pressões parciais de argônio e oxigênio e argônio e nitrogênio, utilizando alvo cerâmico de óxido de zinco ou alvo metálico de zinco. Para alvo de ZnO, filmes com condutividade tipo n foram obtidos em ambiente de argônio, em condições que geraram deficiências de oxigênio. Filmes altamente resistivos foram obtidos com a utilização de pressão parcial de oxigênio no gás de processo, em condições que resultaram em filmes estequiométricos, inclusive com condutividade tipo p. Condutividade tipo p mais alta foi observada, apenas por ponta quente, para uma amostra obtida em argônio logo após a utilização de nitrogênio na câmara de processo, que provavelmente sofreu influência da dopagem não intencional do cobre, que foi identificado como um contaminante do processo devido à estrutura da câmara. Para alvo de Zn, observou-se a formação de nitreto de zinco, que demonstrou alta capacidade de oxidação em ambiente atmosférico, e portanto, transforma-se naturalmente ao longo do tempo ou por processos de oxidação térmica em ZnO dopado com nitrogênio. Filmes de ZnO produzidos a partir de nitreto de zinco foram os únicos dos testados que apresentaram fotoluminescência característica do ZnO, mesmo para processos onde não houve aquecimento intencional.

A Community Analysis of the Implementation for Household Curbside Recycling Programs: A Diversionary Method to Control Municipal Solid Waste

The Municipality of Anchorage (MOA) is required to better manage, operate and control municipal solid waste (MSW) after the Anchorage Assembly instituted a Zero Waste Policy. Two household curbside recycling programs (CRPs), pay-as-you-throw (PAYT) and single-stream, were compared and evaluated to determine an optimal municipal solid waste diversion method for households within the MOA. The analyses find: (1) a CRP must be designed from comprehensive analysis, models and data correlation that combine demographic and psychographic variables; and (2) CRPs can be easily adjusted towards community-specific goals using technology, such as Geographic Information System (GIS) and Radio Frequency Identification (RFID). Combining resources of policy-makers, businesses, and other viable actors are necessary components to produce a sustainable, economically viable curbside recycling program.

Assessing Activity and Location of Individual Laying Hens in Large Groups Using Modern Technology

Tracking individual animals within large groups is increasingly possible, offering an exciting opportunity to researchers. Whereas previously only relatively indistinguishable groups of individual animals could be observed and combined into pen level data, we can now focus on individual actors within these large groups and track their activities across time and space with minimal intervention and disturbance. The development is particularly relevant to the poultry industry as, due to a shift away from battery cages, flock sizes are increasingly becoming larger and environments more complex. Many efforts have been made to track individual bird behavior and activity in large groups using a variety of methodologies with variable success. Of the technologies in use, each has associated benefits and detriments, which can make the approach more or less suitable for certain environments and experiments. Within this article, we have divided several tracking systems that are currently available into two major categories (radio frequency identification and radio signal strength) and review the strengths and weaknesses of each, as well as environments or conditions for which they may be most suitable. We also describe related topics including types of analysis for the data and concerns with selecting focal birds.

Automatic audio signing - literature survey analysis. Interim report, phase 1, task A.

Federal Highway Administration, Washington, D.C.

Federal government use and management of spectrum : hearing before the Committee on Commerce, Science, and Transportation, United States Senate, One Hundred Fourth Congress, second session, June 25, 1996.

Shipping list no.: 97-0097-P.

Motorist aid systems study. State of the art report. Final report.

Federal Highway Administration, Office of Development, Washington, D.C.

San Antonio Alcohol Safety Action Project - analytic study no. 3: analysis of selective enforcements. Final report.

National Highway Traffic Safety Administration, Washington, D.C.