Lipase-catalyzed regioselective acylation of diosgenyl saponins

Diosgenyl saponins were regio selectively acylated by Novozyme 435 with vinyl esters as acylating agents in THF to afford the corresponding mono- or diacyl diosgenyl saponins. (C) 2001 Elsevier Science Ltd. All rights reserved.

Development of a LCST membrane forming system for cellulose acetate ultrafiltration hollow fiber

A novel lower critical solution temperature (LCST) membrane forming system containing cellulose acetate (CA)/poly (vinyl pyrrolidone) (PVP 3 60K)/N-methyl-2-pyrrolidone (NMP)/1,2-propanediol with a weight ratio of 24.0:5.0:62.6:8.4 had been developed. CA hollow fiber ultrafiltration (UF) membranes were fabricated using the dry-wet spinning technique. The fibers were post-treated with a 200 mg/L hypochlorite solution over a period of 6 It at pH 7. The experimental results showed that water flux of a membrane decreased while retention increased with increasing CA concentration in a dope. It was concluded that the membrane pore size decreased with increasing CA concentration. The membrane fouling tendency for BSA was 3 times higher than that for PVP 24K. (C) 2004 Elsevier B.V. All rights reserved.

Advanced polymer membrane development in pervaporation dehydration and lateral flow diagnostics

The work in this thesis concerns the advanced development of polymeric membranes of two types; pervaporation and lateral-flow. The former produced from a solution casting method and the latter from a phase separation. All membranes were produced from casting lacquers. Early research centred on the development of viable membranes. This led to a supported polymer blend pervaporation membrane. Selective layer: plasticized 4:1 mass ratio sodium-alginate: poly(vinyl-alcohol) polymer blend. Using this membrane, pervaporation separation of ethanol/water mixtures was carefully monitored as a function of film thickness and time. Contrary to literature expectations, these films showed increased selectivity and decreased flux as film thickness was reduced. It is argued that morphology and structure of the polymer blend changes with thickness and that these changes define membrane efficiency. Mixed matrix membrane development was done using spherical, discreet, size-monodisperse mesoporous silica particles of 1.8 - 2μm diameter, with pore diameters of ~1.8 nm were incorporated into a poly(vinyl alcohol) [PVA] matrix. Inclusion of silica benefitted pervaporation performance for the dehydration of ethanol, improving flux and selectivity throughout in all but the highest silica content samples. Early lateral-flow membrane research produced a membrane from a basic lacquer composition required for phase inversion; polymer, solvent and non-solvent. Results showed that bringing lacquers to cloud point benefits both the pore structure and skin layers of the membranes. Advancement of this work showed that incorporation of ethanol as a mesosolvent into the lacquer effectively enhances membrane pore structure resulting in an improvement in lateral flow rates of the final membranes. This project details the formation mechanics of pervaporation and lateral-flow membranes and how these can be controlled. The principle methods of control can be applied to the formation of any other flat sheet polymer membranes, opening many avenues of future membrane research and industrial application.

Chemistry and synthesis of 3(2H)-furanones and 4,5-dihydro analogues: mechanistic investigations and stereochemical control

The subject matter of this thesis relates to the chemistry of the five-membered oxygen heterocycles – 3(2H)-furanones and their 4, 5-dihydro analogues. Chapter one of the thesis is a review of the relevant chemistry of the compounds: their synthesis and key transformations. In chapter two, new research on 3(2H)-furanones is outlined in two parts. The first describes an investigation into the cyclisation of α'-trialkylsilyloxyenone adducts with arenesulfenyl and selenenyl chlorides into the corresponding sulfur and selenium substituted 3(2H)-furanones without the involvement of a Lewis acid catalyst. The study, largely involving in situ NMR techniques, identified key features associated with the formation and reaction of the chlorosulfide and chloroselenide intermediates, including operation of the Thorpe-Ingold effect. The knowledge gained in this study was applied (the second part) to the synthesis of vinyl substituted furanone systems from α'-trialkylsilyloxydienones where choice of the reaction conditions and electrophilic reagent was a key feature. An important difference in the behaviour of arenesulfenyl and selenenyl halides towards conjugated dienes emerged from this work. This phase of the research concluded with a new synthesis of geiparvarin, a natural product possessing anti-tumour properties.

Colloidal microgel in removal of water from biodiesel

A series of poly(N-isopropylacrylamide) [pNIPAM]-based homo-polymer and co-polymer microgel particles were prepared by surfactant-free emulsion polymerisation. The co-monomers were acrylic acid. 4-vinylpyridine. butyl acrylate, 4-vinylbiphenyl and vinyl laurate. Co-monomers were added at a concentration of 10% (w/w) relative to the base monomer pNIPAM for the preparation of each co-polymer microgel. The co-monomers chosen vary by their organic chain length, polarity and pH sensitivity, as these should influence how the particles behave in aqueous and non-aqueous solvents. The effect of adding different types of co-monomer into the microgel structure was investigated with respect to their dispersibility in different solvents. These microgel particles have shown useful application in the removal of water from biodiesel prepared from rape seed. Karl Fischer experiments showed that microgel particles can be used to reduce the water content in biodiesel to an acceptable level for incorporation into internal combustion engines. (C) 2008 Elsevier B.V. All rights reserved.

Evaluation of a Water-soluble Bioadhesive Patch for Photodynamic Therapy of Vulval Lesions

An innovative bioadhesive patch intended primarily as a vulval drug delivery system and, specifically, as a means to deliver photosensitisers, or their prodrugs, for photodynamic purposes is described. The patch was formulated with a copolymer of methyl vinyl ether and maleic anhydride (PMVE/MA) as a bioadhesive matrix and poly(vinyl chloride) as a drug-impervious backing layer. Adhesive strength to neonate porcine skin, as a model substrate, was evaluated using peel and tensile testing measurements. Acceptabilities of non-drug loaded patches were appraised using human volunteers and visual-analogue scoring devices. An optimal formulation, with water uptake and peel strengths appropriate for vulval drug delivery, was cast from a 20% (w/w) PMVE/MA solution and adhered with a strength of approximately 1.7 N cm-2. Patient evaluation demonstrated comfort and firm attachment for up to 4 h in mobile patients. Aminolevulinic acid, a commonly used photosensitiser, was formulated into the candidate formulation and applied to vulval intraepithelial neoplastic lesions. Fluorescence under ultraviolet illumination revealed protoporphyrin synthesis. The patch achieves the extended application times obligatory in topical photodynamic therapy of vulval lesions, thereby contributing to potential methods for the eradication of neoplastic lesions in the lower female reproductive tract.

Total Synthesis of (±)-Phomactin G, a Platelet Activating Factor Antagonist from the Marine Fungus Phoma sp.

A total synthesis of phomactin G (3), which is a central intermediate in the biosynthesis of phomactin A (5) in Phoma sp. is described. The synthesis is based on a Cr(II)/Ni(II) macrocyclisation from the aldehyde vinyl iodide 9, leading to 16, followed by sequential conversion of 16 into the -epoxide 21 and the ketone 25 which, on deprotection, led to (±)-phomactin G. Phomactin G (3) shares an interesting structural homology with phomactin D (2), the most potent PAF-antagonist metabolite in Phoma sp. It is most likely converted into phomactin A (5), by initial allylic oxidation to the transient -alcohol phomactin structure 4, known as Sch 49028, followed by spontaneous pyran ring formation.

Co-melt fluidised bed granulation of pharmaceutical powders: Improvements in drug bioavailability

This study investigates the use of co-melt fluidised bed granulation for the agglomeration of model pharmaceutical powders, namely, lactose mono-hydrate, PEG 10000, poly-vinyl pyrolidone and ibuprofen as a model drug. Granulation within the co-melt system was found to follow a nucleationâ??steady growthâ??coating regime profile. Using high molecular weight PEG binder, the granulation mechanism and thus the extent of granulation was found to be significantly influenced by binder viscosity. The compression properties of the granulate within the hot fluidised bed were correlated using a novel high temperature experimental procedure. It was found that the fracture stress and fractural modulus of the materials under hot processing conditions were orders of magnitude lower than those measured under ambient conditions. A range of particle velocities within the granulator were considered based on theoretical models. After an initial period of nucleation, the Stokes deformation number analysis indicated that only velocities within the high shear region of the fluidised bed were sufficient to promote significant granule deformation and therefore, coalescence. The data also indicated that larger granules de-fluidised preventing agglomeration by coalescence. Furthermore, experimental data indicated that dissipation of the viscous molten binder to the surface was the most important factor in the latter stages of the granulation process. From a pharmaceutical perspective the inclusion of the model drug, ibuprofen, combined with PVP in the co-melt process proved to be highly significant. It was found that using DSC analysis on the formulations that the decrease in the heat of fusion associated with the melting of ibuprofen within the FHMG systems may be attributed to interaction between PVP and ibuprofen through inter-molecular hydrogen bonding. This interaction decreases the crystallinity of ibuprofen and facilitates solubilisation and bioavailability within the solid matrix.

Synthesis and characterisation of polymerisable photochromic spiropyrans: towards photomechanical biomaterials

A methodology for the synthesis of novel polymerisable spiropyrans with photomechanical properties suitable for subsequent copolymerisation with either vinyl or acrylate-based biomaterials is described. UV-vis spectroscopic characterisation of photoisomerism shows that photochromic behaviour with respect to related non-polymerisable compounds is retained and is solvent dependent. In acetone, conventional spiropyran-merocyanine photochromism is observed for nitro-spiropyran derivatives, whereas in dichloromethane both nitro-spiropyrans and spiropyrans isomerise to merocyanines which rapidly form H-aggregates. The monomers were designed such that an alkyl spacer of variable length, both electronically and sterically, separates the polymerisable moiety from the photochromic core and allows steric aspects of the resulting photomechanical behaviour to be explored. (c) 2006 Elsevier Ltd. All rights reserved.

Enhanced surface attachment of protein-type targeting ligands to poly(lactide-co-glycolide) nanoparticles using variable expression of polymeric acid functionality

The density of reactive carboxyl groups on the surface of poly(lactide-co-glycolide) (PLGA) nanoparticles (NP) was modulated using a combination of high-molecular weight (MW) encapped and low MW non-encapped PLGA. Carboxyl groups were activated using carbodiimide chemistry and conjugated to bovine serum albumin and a model polyclonal antibody. Activation of carboxyl,groups in solution-phase PLGA prior to NP formation was compared with a postformation activation of peripheral carboxyl groups on intact NP. Activation before or after NP formation did not influence conjugation efficiency to NP prepared using 100% of the low-MW PLGA. The effect of steric stabilization using poly(vinyl alcohol) reduced conjugation of a polyclonal antibody from 62 mu g/(mg NP) to 32 mu g/(mg NP), but enhanced particulate stability. Increasing the amount of a high-MW PLGA also reduced Conjugation, with the activation post-formation still superior to the preformation approach. Drug release studies showed that high proportions of high-MW PLGA in the NP produced a longer sustained release profile of a model drug (celecoxib). It can be concluded that activating intact PLGA NP is superior to activating component parts prior to NP formation. Also, high MW PLGA could be used to prolong drug release, but at the expense of conjugation efficiency on to the NP surface. (C) 2008 Wiley Periodicals, Inc. J Biomed Mater Res 87A: 873-884, 2008

Chemoenzymatic synthesis of trans-dihydrodiol derivatives of monosubstituted benzenes from the corresponding cis-dihydrodiol isomers

Enantiopure trans-dihydrodiols have been obtained by a chemoenzymatic synthesis from the corresponding cis-dihydrodiol metabolites, obtained by dioxygenase-catalysed arene cis-dihydroxylation at the 2,3-bond of monosubstituted benzene substrates. This generally applicable, seven-step synthetic route to trans-dihydrodiols involves a regioselective hydrogenation and a Mitsunobu inversion of configuration at C-2, followed by benzylic bromination and dehydrobromination steps. The method has also been extended to the synthesis of both enantiomers of the trans-dihydrodiol derivatives of toluene, through substitution of a vinyl bromine atom of the corresponding trans-dihydrodiol enantiomers derived from bromobenzene. Through incorporation of hydrogenolysis and diMTPA ester diastereoisomer resolution steps into the synthetic route, both trans-dihydrodiol enantiomers of monohalobenzenes were obtained from the cis-dihydrodiols of 4-haloiodobenzenes.

Polymer-supported phosphoramidites: highly efficient and recyclable catalysts for asymmetric hydrogenation of dimethylitaconate and dehydroamino acids and esters

Several novel phosphoramidites have been prepared by reaction of the primary amines para-vinylaniline, ortho-anisidine, 2-methoxyphenyl(4-vinylbenzyl)amine, 8-aminoquinoline and 3-vinyl-8-aminoquinoline with (S)-1,1'-bi-2-naphthylchlorophosphite, in the presence of base. Rhodium(l) complexes of these phosphoramidites catalyse the asymmetric hydrogenation of dimethylitaconate and dehydroamino acids and esters giving ee values up to 95%. Soluble non-cross linked polymers of the para-vinylaniline and 3-vinyl-8-aminoquinoline-based phosphoramidites have been prepared by free radical co-polymerisation with styrene in the presence of AIBN as initiator. The corresponding [Rh(COD)](+) complexes serve as recyclable catalysts for the asymmetric hydrogenation dimethylitaconate and dehydroamino acids and esters to give ee values up to 80%. (C) 2003 Elsevier Science Ltd. All rights reserved.

Chemoenzymatic synthesis of the trans-dihydrodiol isomers of monosubstituted benzenes via anti-benzene dioxides

Enantiopure cis-2,3-dihydrodiols, available from dioxygenase-catalysed cis-dihydroxylation of monosubstituted benzene substrates, have been used as synthetic precursors of the corresponding trans-3,4-dihydrodiols. The six-step chemoenzymatic route from cis-dihydrodiol precursors, involving acetonide, tetraol, dibromodiacetate and diepoxide intermediates, and substitution of vinyl bromide and iodide atoms, has been used in the synthesis of ten trans-dihydrododiol derivatives of substituted benzenes. The general applicability of the method has been demonstrated by its use in the synthesis of both enantiomers of the trans-1,2- and 3,4-dihydrodiol derivatives of toluene.

Radical 1,4-aryl transfer in arylcarboxamides leading to phthalimides, biaryls and enantiomerically enriched beta-arylethylamines

5-exo Cyclisation of vinyl-, aryl- and alkyl-radicals onto the aryl group of arylcarboxamides is followed by beta-scission of the resulting spirocyclohexadienyl radicals with ejection of a carbamoyl radical. The fate of this radical depends on the substrate but, in the cases studied, either 5-endo cyclisation or direct reduction follows to give phthalimides, biaryls or beta-arylethylamines.

A total synthesis of (+/-)-phomactin A

A total synthesis of the PAF antagonist phomactin A (1), isolated from the marine fungus Phoma sp. is described. The synthesis is based on a Cr(II)/Ni(II) macrocyclisation from the aldehyde vinyl iodide 14, leading to the key phomactatrienol intermediate 16a, followed by elaboration of 16a to the epoxyketone 21, which undergoes spontaneous pyran and hemiacetal ring formation to 1 on deprotection with DDQ.