Pyroelectric conversion: harvesting energy from temperature fluctuations

Peer reviewed

Mass and energy balance of the carbonization of babassu nutshell as affected by temperature

The objective of this work was to evaluate the carbonization yield of babassu nutshell as affected by final temperature, as well as the energy losses involved in the process. Three layers constituting the babassu nut, that is, the epicarp, mesocarp and endocarp, were used together. The material was carbonized, considering the following final temperatures: 450, 550, 650, 750, and 850ºC. The following were evaluated: energy and charcoal yields, pyroligneous liquid, non-condensable gases, and fixed carbon. The use of babassu nutshell can be highly feasible for charcoal production. The yield of charcoal from babassu nutshell carbonization was higher than that reported in the literature for Eucalyptus wood carbonization, considering the final temperature of 450ºC. Charcoal and energy yields decreased more sharply at lower temperatures, with a tendency to stabilize at higher temperatures. The energy yields obtained can be considered satisfactory, with losses between 45 and 52% (based on higher heating value) and between 43 and 49% (based on lower heating value) at temperatures ranging from 450 to 850ºC, respectively. Yields in fixed carbon and pyroligneous liquid are not affected by the final carbonization temperature.

Study of post-deposition contamination in low-temperature deposited polysilicon films

The presence of hydrogen in polysilicon films obtained at low temperatures by hot-wire CVD and the post-deposition oxidation by air-exposure of the films are studied in this paper. The experimental results from several characterization techniques (infrared spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry and wavelength dispersive spectroscopy) showed that hydrogen and oxygen are homogeneously distributed at grain boundaries throughout the depth of the films. Hydrogen is introduced during the growth process and its concentration is higher in samples deposited at lower temperatures. Oxygen diffuses along the grain boundaries and binds to silicon atoms, mainly in Si 2O groups.

Vortex-putken ominaisuudetkuivaussovellutuksessa

Työssä tarkastellaan vortex-putken soveltuvuutta kostean ilman kuivatukseen ja vapautuvan latenttilämmön hyödyntämiseen. Soveltuvuutta arvioidaan veden ja ilman massataseita hyväksi käyttäen ja stationaarisen systeemin energiataseen avulla. Työn mittauksia varten rakennettiin koelaitteisto, jonka avulla mitattiin miten lämpötilaerot kuumassa ja kylmässä päässä käyttäytyivät mitattaessa kuivalla ilmalla ja ilmalla, jota oli kostutettu. Mitattavia suureita olivat syöttöpaine- ja lämpötila, lämpötilat kuumassa ja kylmässä päässä, kuuman pään paine ja tilavuusvirta tai virtausnopeus ja kuuman pään suhteellinen kosteus. Mittaustulosten avulla laskettiin lämpötilan muutokset kummassakin päässä ja verrattiin kuivan ja kostean ilman mittauksien tuloksia toisiinsa. Lisäksi laskettiin tiivistyneen veden määrä ja veden ja ilman massavirrat molemmissa päissä. Näin voitiin laskea tiivistymisessä vapautuva energia ja tarkastella mihin se siirtyy. Tulosten perusteella vortex-putki soveltuu hyvin huonosti ilman kuivatukseen. Tiivistyneen veden määrä ja sitä kautta tiivistymisessä vapautunut energia, olivat pieniä. Suurin osa kosteudesta meni kuuman pään virtauksen mukana. Tiivistymisessä vapautunut energia siirtyi kylmään päähän.

In vitro evaluation of the temperature increment at the external root surface after Er,Cr: YSGG laser irradiation of the root canal

Objectives: A study was made to determine the temperature increment at the dental root surface following Er,Cr:YSGG laser irradiation of the root canal. Design. Human canines and incisors previously instrumented to K file number ISO 30 were used. Irradiation was carried out with glass fiber endodontic tips measuring 200 μm in diameter and especially designed for insertion in the root canal. The teeth were irradiated at 1 and 2 W for 30 seconds, without water spraying or air, and applying a continuous circular movement (approximately 2 mm/sec.) in the apico-coronal direction. Results: At the 1 W power setting, the mean temperature increment was 3.84ºC versus 5.01ºC at 2 W. In all cases the difference in mean value obtained after irradiation versus the mean baseline temperature proved statistically significant (p< 0.05). Conclusions: Application of the Er,Cr:YSGG laser gives rise to a statistically significant temperature increment at the external root surface, though this increment is probably clinically irrelevant, since it would appear to damage the tissues (periodontal ligament and alveolar bone) in proximity to the treated tooth

In-line Monitoring of Precipitation Process using Raman Spectroscopy and ATR-FTIR

Polymorfian jatkuva seuranta saostuksessa on hyödyllistä suunnittelun ja kidetuotteen ominaisuuksien sekä kiteytystä seuraavan jatkoprosessoinnin kannalta. Tässä diplomityössä on tutkittu L-glutamiinihapon kahden (- ja ß) polymorfimuodon liukoisuuden riippuvuutta pH:sta ja lämpötilasta.Tulokseksi saatiin, että kummankin polymorfin liukoisuus kasvoi sekä pH:ta ettälämpötilaa kasvatettaessa. ¿¿muodon liukoisuus oli korkeampi kuin ß-muodon liukoisuus valituilla pH-arvoilla eri lämpötiloissa. Lisäksi seurattiin puolipanostoimisen saostuksen aikana 1-litraisella laboratoriokiteyttimellä muodostuvan kiteisen polymorfiseoksen koostumusta hyödyntäen in-line Raman-spektroskopiaa. Myös liuoksen pH-muutosta seurattiin sekä liuoksen koostumusta ATR FTIR-spektroskopian (Attenuated Total Reflection Fourier Transform Infrared Spectrometer) avulla. Tutkittavina muuttujina olivat mm. sekoitusintensiteetti, sekoitintyyppi, reaktanttien (natriumglutamaatti ja rikkihappo) konsentraatiot sekä syötetyn rikkihapon syöttökohta kiteyttimessä. Työhön sisältyi 36 koetta ja osa kokeista toistettiin tulosten oikeellisuuden tarkistamiseksi. Inline-mittaustulosten verifioimiseksi kidenäytteet analysoitiin myös käyttämällä konfokaali Raman-mikroskooppia. Kidemorfologiaa tutkittiin SEM-kuvien (Scanning Eletronic Microscope) avulla. Työ osoitti, että Raman-spektroskopia on joustava ja luotettava menetelmä saostusprosessin jatkuvaan seurantaan L-glutamiinihapolla. Alhaiset lähtöainepitoisuudet tuottivat pääasiassa ¿¿muotoa, kun taas alhainen sekoitusteho edisti ß-muodon muodostumista. Syöttökohta vaikutti merkittävästi polymorfiaan. Kun rikkihapon syöttökohta oli epäideaalisesti sekoitetulla vyöhykkeellä, nousi ylikylläisyystaso korkeaksi ja päätuote oli tällöin ß-muotoa. 6-lapainen vinolapaturbiini (nousukulma 45o) ja 6-lapainen levyturbiini eivät merkittävästi poikenneet toisistaan muodostuvien polymorfien osalta.

Effect of temperature on percentage of germination of canistel seeds (Pouteria campechiana)

The canistel is a fruit originated in Mexico and Central America, being introduced in Brazil in 1986. The plants present medium size, however it can reach up to 15 meters of height; the leaves measure about 10 to 25 cm; the flowers are complete and small and the fruit presents yellow coloration when ripe, with whitish pulp and sweet flavor. The propagation can be realized by seed or grafting. In view of almost total absence of information about the culture and the possibility to have a commercial cultivation, the present work, was live in which the effect of the temperature was evaluated in the percentage of germination of the seeds. It was checked that the best averages were obtained in temperature of 30ºC and the minor in 15ºC, 20ºC and 40ºC could be considerate the worst of them.

Evolution of superficial lake water temperature profile under diurnal radiative forcing

In lentic water bodies, such as lakes, the water temperature near the surface typically increases during the day, and decreases during the night as a consequence of the diurnal radiative forcing (solar and infrared radiation). These temperature variations penetrate vertically into the water, transported mainly by heat conduction enhanced by eddy diffusion, which may vary due to atmospheric conditions, surface wave breaking, and internal dynamics of the water body. These two processes can be described in terms of an effective thermal diffusivity, which can be experimentally estimated. However, the transparency of the water (depending on turbidity) also allows solar radiation to penetrate below the surface into the water body, where it is locally absorbed (either by the water or by the deployed sensors). This process makes the estimation of effective thermal diffusivity from experimental water temperature profiles more difficult. In this study, we analyze water temperature profiles in a lake with the aim of showing that assessment of the role played by radiative forcing is necessary to estimate the effective thermal diffusivity. To this end we investigate diurnal water temperature fluctuations with depth. We try to quantify the effect of locally absorbed radiation and assess the impact of atmospheric conditions (wind speed, net radiation) on the estimation of the thermal diffusivity. The whole analysis is based on the results of fiber optic distributed temperature sensing, which allows unprecedented high spatial resolution measurements (∼4 mm) of the temperature profile in the water and near the water surface.

Effects of packaging and temperature on postharvest of atemoya

Effects of refrigerated storage and different packages on postharvest behaviour of fruits of atemoya (Annona cherimola x A. squamosa) cv. PR3 were investigated. Fruits were individually sealed in copolymer (PD-955) and low-density polyethylene (LDPE) bags and stored for 21 days at 15°C or 25°C. Then they were unwrapped and maintained at 25°C, for ripening. Weight loss and firmness of fruits were both affected by storage time, temperature and packaging. Weight loss in packaged atemoyas was lower than in the control, non-wrapped fruits. A non-trained panel scored the atemoyas for overall eating quality and appearance. Fruits sealed in LDPE did not ripen, probably due to an injurious atmosphere developed inside the package. Atemoyas packaged in PD-955 film had a shelf-life of 17 days against 13 days of the control ones, both stored at 15°C, an increase of 30% on shelf-life.

Influence of the temperature in germination of seeds of jabuticaba tree

The jaboticaba tree (Myrciaria spp.) is originated from the center-south of Brazil and presents different types. It's a medium size tree, with tendency to form a crown with great number of branches. A characteristic considered as limitant for the commercial crop is the great juvenility, advicing producing good rootstocks of seedlings and graft wanted varieties, and other vegetative processes. With the purpose of evaluating the effect of temperature on germination of three clones of jaboticaba tree, was carried out a laboratorial research. It was observed influence of the temperature on germination. The highest percentage of germination was obtained at low temperature (15ºC and 20ºC). When it was used the temperature of 35ºC, two clones had only 8% of germination, while the other one was verified 35%. These values show the possibility of the ocurrence of variability among the clones of jaboticaba tree.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

On the Reversed Brayton Cycle with High Speed Machinery

This work was carried out in the laboratory of Fluid Dynamics, at Lappeenranta University of Technology during the years 1991-1996. The research was a part of larger high speed technology development research. First, there was the idea of making high speed machinery applications with the Brayton cycle. There was a clear need to deepen theknowledge of the cycle itself and to make a new approach in the field of the research. Also, the removal of water from the humid air seemed very interesting. The goal of this work was to study methods of designing high speed machinery to the reversed Brayton cycle, from theoretical principles to practical applications. The reversed Brayton cycle can be employed as an air dryer, a heat pump or a refrigerating machine. In this research the use of humid air as a working fluid has an environmental advantage, as well. A new calculation method for the Braytoncycle is developed. In this method especially the expansion process in the turbine is important because of the condensation of the water vapour in the humid air. This physical phenomena can have significant effects on the level of performance of the application. Also, the influence of calculating the process with actual, achievable process equipment efficiencies is essential for the development of the future machinery. The above theoretical calculations are confirmed with two different laboratory prototypes. The high speed machinery concept allows one to build an application with only one rotating shaft including all the major parts: the high speed motor, the compressor and the turbine wheel. The use of oil free bearings and high rotational speed outlines give several advantages compared to conventional machineries: light weight, compact structure, safe operation andhigher efficiency at a large operational region. There are always problems whentheory is applied to practice. The calibrations of pressure, temperature and humidity probes were made with care but still measurable errors were not negligible. Several different separators were examined and in all cases the content of the separated water was not exact. Due to the compact sizes and structures of the prototypes, the process measurement was slightly difficult. The experimental results agree well with the theoretical calculations. These experiments prove the operation of the process and lay a ground for the further development. The results of this work give very promising possibilities for the design of new, commercially competitive applications that use high speed machinery and the reversed Brayton cycle.

Effect of temperature and moisture on the dormancy and activation pattern of Oxalis latifolia bulbs

Con objeto de buscar información para un mejor control de Oxalis latifolia Kunth, se ha estudiado el efecto que presentan la temperatura y la humedad sobre la activación de sus bulbos, tanto en la forma común como en la forma Cornwall de la misma. Los bulbos de la mala hierba se mantuvieron en un refrigerador a +4°C durante 13, 20, 27, 41, 48 y 55 días. Se sacaron tres grupos de 30 bulbos de cada forma en cada fecha de muestreo y se colocaron a 21°C; 15 de ellos se mantuvieron en condiciones de sequía —no se regaron— y otros 15 en condiciones de humedad —añadiendo el agua necesaria—. Los resultados muestran que la activación ocurre durante un período prolongado de tiempo en ambas formas, tanto en seco como en húmedo. También se observó que los bulbos secos se activaron antes que los húmedos y los de la forma común antes que los Cornwall. Se observaron dos patrones de activación: los bulbos secos de la forma común generalmente presentaron una activación que sigue un patrón logarítmico, mientras que sus bulbos humedecidos mostraron una tendencia linear; los bulbos Cornwall se activaron con una tendencia exponencial en la mayoría de los casos. El tiempo medio requerido para la activación después del almacenamiento en frío fue constante en la forma común, sin embargo la activación de Cornwall fue más rápida cuanto más tiempo permanecieron almacenados en frío.

Earliness per se and its dependence upon temperature in diploid wheat lines differing in the major gene Eps-Am1 alleles

Differences in development among wheat cultivars are not only restricted to photoperiod and vernalization responses. When both requirements are fully satisfied differences may still arise due to earliness per se. It is not clear at present to what extent this trait is ‘ intrinsically ’ expressed (a constitutive trait) independently of the environmental conditions so that it might be selected under any thermal condition or if it may be altered to the extent of showing a crossover interaction with temperature in which the ranking of wheat genotypes may be altered. The present study assessed the influence of temperature on the intrinsic earliness for lines of diploid wheat characterized for their differences in a major gene for intrinsic earliness, but also possibly differing in their genetic background for other factors controlling this polygenic trait. To do so the lines were grown individually in two temperature regimes (16 and 23 xC) under long days having previously been fully vernalized. Multiple comparisons analyses were carried out among lines of the same allelic group for the Eps-Am1 gene. Results indicated that within each group there were lines that did not differ in their earliness per se, others differed but without exhibiting any linertemperature interaction and finally different types of interaction were shown, including cases where the ranking of lines was altered depending on the growing temperature. It is thus possible that the selection of a genotype based on its earliness per se in an environment might not represent the same performance in another location where temperature varied significantly.

Effect of temperature and carpel size during pre-anthesis on potential grain weight in wheat

The effect of environmental conditions immediately before anthesis on potential grain weight was investigated in wheat at the experimental field of the Faculty of Agronomy (University of Buenos Aires, Argentina) during 1995 and 1996. Plants of two cultivars of wheat were grown in two environments (two contrasting sowing dates) to provide different background temperature conditions. In these environments, transparent boxes were installed covering the spikes in order to increase spike temperature for a short period (c. 6 days) immediately before anthesis, i.e. between ear emergence and anthesis. In both environments, transparent boxes increased mean temperatures by at least 3n8 mC. These increases were almost entirely due to the changes in maximum temperatures because minimum temperatures were little affected. Final grain weight was significantly reduced by higher temperature during the ear emergence–anthesis period. It is possible that this reduction could be mediated by the effect of the heat treatment on carpel weight at anthesis because a curvilinear association between final grain weight and carpel weight at anthesis was found. This curvilinear association may also indicate a threshold carpel weight for maximizing grain weight.