Suppressing grazing chaos in impacting system by structural nonlinearity

In this note we investigate the influence of structural nonlinearity of a simple cantilever beam impacting system on its dynamic responses close to grazing incidence by a means of numerical simulation. To obtain a clear picture of this effect we considered two systems exhibiting impacting motion, where the primary stiffness is either linear (piecewise linear system) or nonlinear (piecewise nonlinear system). Two systems were studied by constructing bifurcation diagrams, basins of attractions, Lyapunov exponents and parameter plots. In our analysis we focused on the grazing transitions from no impact to impact motion. We observed that the dynamic responses of these two similar systems are qualitatively different around the grazing transitions. For the piecewise linear system, we identified on the parameter space a considerable region with chaotic behaviour, while for the piecewise nonlinear system we found just periodic attractors. We postulate that the structural nonlinearity of the cantilever impacting beam suppresses chaos near grazing. (C) 2007 Elsevier Ltd. All rights reserved.

Experimental identification of chaotic fibers

In a 2D parameter space, by using nine experimental time series of a Clitia`s circuit, we characterized three codimension-1 chaotic fibers parallel to a period-3 window. To show the local preservation of the properties of the chaotic attractors in each fiber, we applied the closed return technique and two distinct topological methods. With the first topological method we calculated the linking, numbers in the sets of unstable periodic orbits, and with the second one we obtained the symbolic planes and the topological entropies by applying symbolic dynamic analysis. (C) 2007 Elsevier Ltd. All rights reserved.

The effect of the negative coupling parameter on the spectrum of a trapped Bose gas

The interest in attractive Bose-Einstein Condensates arises due to the chemical instabilities generate when the number of trapped atoms is above a critical number. In this case, recombination process promotes the collapse of the cloud. This behavior is normally geometry dependent. Within the context of the mean field approximation, the system is described by the Gross-Pitaevskii equation. We have considered the attractive Bose-Einstein condensate, confined in a nonspherical trap, investigating numerically and analytically the solutions, using controlled perturbation and self-similar approximation methods. This approximation is valid in all interval of the negative coupling parameter allowing interpolation between weak-coupling and strong-coupling limits. When using the self-similar approximation methods, accurate analytical formulas were derived. These obtained expressions are discussed for several different traps and may contribute to the understanding of experimental observations.

One-dimensional trapped atoms: critical coupling parameter and critical number of particles

In this paper we consider the case of a Bose gas in low dimension in order to illustrate the applicability of a method that allows us to construct analytical relations, valid for a broad range of coupling parameters, for a function which asymptotic expansions are known. The method is well suitable to investigate the problem of stability of a collection of Bose particles trapped in one- dimensional configuration for the case where the scattering length presents a negative value. The eigenvalues for this interacting quantum one-dimensional many particle system become negative when the interactions overcome the trapping energy and, in this case, the system becomes unstable. Here we calculate the critical coupling parameter and apply for the case of Lithium atoms obtaining the critical number of particles for the limit of stability.

Preparation and characterization of new glassy system As2P2S8-Ga2S3

Glasses having the composition (100 - x)As2P2S8-xGa(2)S(3) with x ranging from 0 to 50% were investigated to determine the compositional effect on properties and local structure. The glass transition temperature (T-g) and the stability parameter against crystallization (T-x - T-g) increased with the addition of Ga2S3. The structure of these glasses was probed by Raman scattering, Fourier transform infrared (FT-IR) and P-31 nuclear magnetic resonance. On the basis of the observed vibrations and the strength of the P-31-P-31 homonuclear magnetic dipolar coupling, two scenarios can be proposed for the structural evolution induced by the addition of Ga2S3. For x <= 20% we may have the formation of GaS4E- groups (E = nonbonding electron), and for x >= 30% we have depolymerization of the As2P2S8 units and the formation of a network of GaPS4 units with each PS4/2 unit (Q(4)) species carrying a single positive formal charge.

The transcriptional response to cadmium, organic hydroperoxide, singlet oxygen and UV-A mediated by the sigma(E)-ChrR system in Caulobacter crescentus

Caulobacter crescentus sigma(E) belongs to the ECF (extracytoplasmic function) subfamily of RNA polymerase sigma factors, whose members regulate gene expression in response to distinct environmental stresses. During physiological growth conditions, data indicate that sigma(E) is maintained in reduced levels due to the action of ChrR, a negative regulator of rpoE gene expression and function. However, once bacterial cells are exposed to cadmium, organic hydroperoxide, singlet oxygen or UV-A irradiation, transcription of rpoE is induced in a sigma(E)-dependent manner. Site-directed mutagenesis indicated that residue C188 in ChrR is critical for the cadmium response while residues H140 and H142 are required for the bacterial response to organic hydroperoxide, singlet oxygen and UV-A. Global transcriptional analysis showed that sigma(E) regulates genes involved in protecting cells against oxidative damages. A combination of transcriptional start site identification and promoter prediction revealed that some of these genes contain a putative sigma(E)-dependent motif in their upstream regions. Furthermore, deletion of rpoE and two sigma(E)-dependent genes (cfaS and hsp20) impairs Caulobacter survival when singlet oxygen is constantly generated in the cells.

Identification of protein-coding and intronic noncoding RNAs down-regulated in clear cell renal carcinoma

The clear cell subtype of renal cell carcinoma (RCC) is the most lethal and prevalent cancer of the urinary system. To investigate the molecular changes associated with malignant transformation in clear cell RCC, the gene expression profiles of matched samples of tumor and adjacent non-neoplastic tissue were obtained from six patients. A custom-built cDNA microarray platform was used, comprising 2292 probes that map to exons of genes and 822 probes for noncoding RNAs mapping to intronic regions. Intronic transcription was detected in all normal and neoplastic renal tissues. A subset of 55 transcripts was significantly down-regulated in clear cell RCC relative to the matched nontumor tissue as determined by a combination of two statistical tests and leave-one-out patient cross-validation. Among the down-regulated transcripts, 49 mapped to untranslated or coding exons and 6 were intronic relative to known exons of protein-coding genes. Lower levels of expression of SIN3B, TRIP3, SYNJ2BP and NDE1 (P<0.02), and of intronic transcripts derived from SND1 and ACTN4 loci (P<0.05), were confirmed in clear cell RCC by Real-time RT-PCR. A subset of 25 transcripts was deregulated in additional six nonclear cell RCC samples, pointing to common transcriptional alterations in RCC irrespective of the histological subtype or differentiation state of the tumor. Our results indicate a novel set of tumor suppressor gene candidates, including noncoding intronic RNAs, which may play a significant role in malignant transformations of normal renal cells. (C) 2008 Wiley-Liss, Inc.

Identification of an Operon, Pil-Chp, That Controls Twitching Motility and Virulence in Xylella fastidiosa

Xylella fastidiosa is an important phytopathogenic bacterium that causes many serious plant diseases, including Pierce`s disease of grapevines. Disease manifestation by X. fastidiosa is associated with the expression of several factors, including the type IV pili that are required for twitching motility. We provide evidence that an operon, named Pil-Chp, with genes homologous to those found in chemotaxis systems, regulates twitching motility. Transposon insertion into the pilL gene of the operon resulted in loss of twitching motility (pilL is homologous to cheA genes encoding kinases). The X. fastidiosa mutant maintained the type IV pili, indicating that the disrupted pilL or downstream operon genes are involved in pili function, and not biogenesis. The mutated X. fastidiosa produced less biofilm than wild-type cells, indicating that the operon contributes to biofilm formation. Finally, in planta the mutant produced delayed and less severe disease, indicating that the Pil-Chp operon contributes to the virulence of X. fastidiosa, presumably through its role in twitching motility.

TLC Separation and Identification of the Essential Oil Constituents from Aloysia gratissima

The present work had as objective the isolation of the five compounds by thin-layer Chromatography (TLC) from the essential oil of the Aloysia gratissima. For this, a number of systems of eluents were used for its separation, indicating that through the system acetone/hexane in proportions (v/v) 1:30 it was possible to isolate guaiol, elemol, pinocanphone (trans-3-pinanone), cis-pinocarvyl, and acorenone. The isolation of the compound acorenone from the other compounds was possible with the mixture of solvents hexane/dichloromethane in proportions (v/v) (1:1,3).

Six-Day System Test and Component test and System Simulation for Combitanks with Internal heat Exchangers

An international standard, ISO/DP 9459-4 has been proposed to establish a uniform standard of quality for small, factory-made solar heating systerns. In this proposal, system components are tested separatelyand total system performance is calculated using system simulations based on component model parameter values validated using the results from the component tests. Another approach is to test the whole system in operation under representative conditions, where the results can be used as a measure of the general system performance. The advantage of system testing of this form is that it is not dependent on simulations and the possible inaccuracies of the models. Its disadvantage is that it is restricted to the boundary conditions for the test. Component testing and system simulation is flexible, but requires an accurate and reliable simulation model.The heat store is a key component conceming system performance. Thus, this work focuses on the storage system consisting store, electrical auxiliary heater, heat exchangers and tempering valve. Four different storage system configurations with a volume of 750 litre were tested in an indoor system test using a six -day test sequence. A store component test and system simulation was carried out on one of the four configurations, applying the proposed standard for stores, ISO/DP 9459-4A. Three newly developed test sequences for intemalload side heat exchangers, not in the proposed ISO standard, were also carried out. The MULTIPORT store model was used for this work. This paper discusses the results of the indoor system test, the store component test, the validation of the store model parameter values and the system simulations.

Energy Storage for a Grid-Connected PV-System: A Feasibility Study

The work presented in this thesis concerns the dimensioning of an Energy Storage System (ESS) which will be used as an energy buffer for a grid-connected PV plant. This ESS should help managing the PV plant to inject electricity into the grid according to the requirements of the grid System Operator. It is desired to obtain a final production not below 1300kWh/kWp with a maximum ESS budget of 0.9€/Wp. The PV plant will be sited in Martinique Island and connected to the main grid. This grid is a small one where the perturbations due clouds in the PV generation are not negligible anymore. A software simulation tool, incorporating a model for the PV-plant production, the ESS and the required injection pattern of electricity into the grid has been developed in MS Excel. This tool has been used to optimize the relevant parameters defining the ESS so that the feed-in of electricity into the grid can be controlled to fulfill the conditions given by the System Operator. The inputs used for this simulation tool are, besides the conditions given by the System Operator on the allowed injection pattern, the production data from a similar PV-plant in a close-by location, and variables for defining the ESS. The PV production data used is from a site with similar climate and weather conditions as for the site on the Martinique Island and hence gives information on the short term insolation variations as well as expected annual electricity production. The ESS capacity and the injected electric energy will be the main figures to compare while doing an economic study of the whole plant. Hence, the Net Present Value, Benefit to Cost method and Pay-back period studies are carried on as dependent of the ESS capacity. The conclusion of this work is that it is possible to obtain the requested injection pattern by using an ESS. The design of the ESS can be made within an acceptable budget. The capacity of ESS to link with the PV system depends on the priorities of the final output characteristics, and it also depends on which economic parameter that is chosen as a priority.

Supervision as control system : the design of supervision as a regulatory instrument in the social services sector in Sweden

In this article, the prevailing official view of supervision as a regulatory instrument is examined as it applies to the social services sector in Sweden. The study is based on a comparison of the views expressed on the design of supervision as a regulatory instrument by two government commissions, the Supervision Commission and the Commission on Supervision within the Social Services (UTIS), and on the positions taken by the Government regarding the definitions of the concept of supervision proposed by these commissions. The view of supervision as a regulatory instrument expressed in these policy documents is analysed with the help of a theoretical framework describing the components, their functions and the governance characteristics of control systems. In the framework separate interrelated characteristics of the components are identified and summarized into two models of control systems. The analysis shows that supervision in the Swedish social services sector can be described in terms of both a disciplinary and non-disciplinary system. By its system theoretical basis and the identification of interrelated characteristics the study contributes to a broadened understanding of the construction and functions of supervision as a regulatory instrument and of how supervision within the Swedish social sector is meant to be designed.

Handbok för kombinerade sol- och biovärmesystem : Teknik - System - Ekonomi

Handboken beskriver olika solfångarkonstruktioner och solvärmekretsens ingående komponenter och ger en grundlig inblick i ackumulatortankens konstruktion och funktion. I boken finns förslag på systemutformning, olika tekniska lösningar och hur systemen bör styras och regleras. Handboken beskriver i första hand utformning-lösning-styrning av kombinationen sol- och pelletsvärme, men tar även upp solvärme i kombination med vedpannor, värmedrivna vitvaror och värmepumpar. Värmesystem med vattenburen värme är utmärkta att kombinera med solvärme, men det är i de flesta fall enklare att få till bra lösningar vid nyinstallation, än vid komplettering av befintlig anläggning. När solvärme och pelletsvärme ska kombineras finns det många alternativ till systemutformning. Det är viktigt att vattenburna pelletssystem utformas korrekt och kombineras på rätt sätt med solvärme för att komforten ska bli hög och elanvändningen låg. Vattenmantlade pelletskaminer med ett vattenburet värmesystem är extra intressant i kombination med solvärme. När eldningen upphör i samband med att värmebehovet avtar kan solvärmen ta över. En generell slutsats är att konventionella svenska pelletspannor med inbyggd varmvattenberedning inte är lämpliga i kombination med solvärmesystem. Den typen av bränslepannor ger komplicerade systemlösningar, höga värmeförluster och det är svårt att åstadkomma en tillräckligt bra temperaturskiktning i ackumulatortanken om varmvattenberedning sker i pannan. Solvärme för varmvattenberedning kan vara ett enkelt och bra komplement till pelletskaminer som genererar varmluft. För solvärmesystem är det viktigt att kraftig temperaturskiktning erhålls när värmelagret laddas ur. Det betyder att ackumulatortankens (eller varmvattenberedarens) nedre vattenvolym ska kylas ner till temperaturer som ligger nära ingående kallvattentemperatur. Ackumulatortankens mellersta del bör kylas till samma temperatur som radiatorreturen. Vid design av solfångarkretsen måste överhettning och stagnation kunna klaras utan risk för glykolnedbrytning eller andra skador på värmebärare eller rörkrets (och andra komponenter i kretsen). Partiell förångning minskar risken för att glykolen skadas då solfångaren når höga stagnationstemperaturer. Solfångarens glykolblandning tillåts koka (förångas) på ett kontrollerat sätt så att endast ånga blir kvar i solfångaren. Vätskevolymen i solfångaren samlas upp i ett större expansionskärl och systemet återfylls när vätskan kondenserar. Dränerande solfångarsystem med enbart vatten är ett möjligt alternativ till konventionella solfångare. De kräver en större noggrannhet vid installationen, så att sönderfrysning undviks. Dränerande systemlösningar är relativt ovanliga i Sverige. Om solfångaren under senhöst-vinter-tidig vår kan arbeta med att förvärma kallvatten från 10 till 20 ºC erhålls en betydligt bättre verkningsgrad på solfångaren (och framför allt ökar värmeutbytet då drifttimmarna ökar väsentligt) än om radiatorreturen (som i bästa fall ligger på temperaturnivån 30 - 40 ºC) ska förvärmas. Därför bör radiatorreturen placeras en bra bit upp från botten i ackumulatortanken och tappvarmvattnet ska förvärmas i en slinga som börjar i tankens botten. Om det finns ett VVC-system måste systemet anslutas på ett speciellt sätt så att ackumulatortankens temperaturskiktning inte störs. En viktig parameter vid ackumulatortankens utformning är att värmeförlusterna hålls låga. Det är viktigt för att klara tappvarmvattenlasten med solvärme under mulna perioder sommartid (men också för att hålla energianvändningen låg). I moderna hus, där ackumulatortanken i regel placeras i bostaden, blir det en komfortfråga att undvika övertemperaturer i det rum där värmelagret placeras. En bra standard på isoleringen (med minimerade värmeförluster) kräver att det finns ett lufttätt skikt över hela isoleringen som dessutom sluter tätt mot röranslutningar. Ofrivillig självcirkulation i anslutande kretsar som kan kyla av och blanda om ackumulatortankens vattenvolym, bör förhindras med backventiler och nedböjning av rören i isolerskiktet eller direkt utanför tanken.

An Agent-Based Approach to Real-Time Patient Identification for Clinical Trials

Patient recruitment for clinical trials is expensive and has been a significant challenge, with many trials not achieving their recruitment goals. One method that shows promise for improving recruitment is the use of interactive prompts that inform practitioners of patient eligibility for clinical trials during consultation. This paper presents the ePCRN-IDEA recruitment system, which utilises an agent-based infrastructure to enable real-time recruitment of patients. In essence, whenever patients enter a clinic, the system compares their details against eligibility criteria, which define the requirements of active clinical trials. If a patient is found to be eligible, a prompt is raised to notify the user. In this way, it becomes possible for recruitment to take place quickly in a cost effective manner, whilst maintaining patient trust through the involvement of their own health care practitioner.

A Gradient-Type Method For Real-Time State Estimation Of Water Distribution Networks

Drinking water distribution networks risk exposure to malicious or accidental contamination. Several levels of responses are conceivable. One of them consists to install a sensor network to monitor the system on real time. Once a contamination has been detected, this is also important to take appropriate counter-measures. In the SMaRT-OnlineWDN project, this relies on modeling to predict both hydraulics and water quality. An online model use makes identification of the contaminant source and simulation of the contaminated area possible. The objective of this paper is to present SMaRT-OnlineWDN experience and research results for hydraulic state estimation with sampling frequency of few minutes. A least squares problem with bound constraints is formulated to adjust demand class coefficient to best fit the observed values at a given time. The criterion is a Huber function to limit the influence of outliers. A Tikhonov regularization is introduced for consideration of prior information on the parameter vector. Then the Levenberg-Marquardt algorithm is applied that use derivative information for limiting the number of iterations. Confidence intervals for the state prediction are also given. The results are presented and discussed on real networks in France and Germany.