Designing and testing of a sensor based on a magnetoresistive manganese perovskite thick film

In this paper we report on the growth of thick films of magnetoresistive La2/3Sr1/3MnO3 by using spray and screen printing techniques on various substrates (Al2O3 and ZrO2). The growth conditions are explored in order to optimize the microstructure of the films. The films display a room-temperature magnetoresistance of 0.0012%/Oe in the 1 kOe field region. A magnetic sensor is described and tested.

Innovative Leak Test for Pavement Joint Seals, Progress Report, HR-318, 1993

Premature failure of concrete pavement contraction joint seals is an ongoing and costly problem for the Iowa Department of Transportation. Several joint seal test sections consisting of variations in sawing methods, joint cleaning techniques, sealant installation, and sealant types have been established over the past few years. Laboratory analysis and field inspections were done as a part of the tests, and core samples were taken for laboratory adhesion pull tests. Such methods often cover specifically small areas and may not expose hidden failures. Some tests are also labor-intensive and destructive, especially that of coring. An innovative, nondestructive, broad coverage joint seal tester that yields quick results has been designed and developed for evaluation of pavement joint seal performance. The Iowa vacuum joint seal tester (IA-VAC) applies a low vacuum above a joint seal that has been spray-covered with a foaming water solution. Any unsealed area or leak that exists along the joint will become quickly and clearly visible by the development of bubbles at the leak point. By analyzing the results from the IA-VAC tests, information on the number and types of leaks can be obtained; such information will help identify the source of the problem and direct efforts toward a solution.

High Molecular Weight Methacrylate Sealing of a Bridge Deck, HR-2031, 1988

The Iowa Department of Transportation used a high molecular weight methacrylate (HMWM) resin to seal a 3,340 ft. x 64 ft. bridge deck in October 1986. The sealing was necessary to prevent deicing salt brine from entering a substantial number of transverse cracks that coincided with the epoxy coated top steel and unprotected bottom steel. HMWM resin is a three component product composed of a monomer, a cumene hydroperoxide initiator and a cobalt naphthenate promoter. The HMWM was applied with a dual spray bar system and flat-fan nozzles. Initiated monomer delivered through one spray bar was mixed in the air with promoted monomer from the other spray bar. The application rate averaged 0.956 gallons per 100 square feet for the tined textured driving lanes. Dry sand was broadcast on the surface at an average coverage of 0.58 lbs. per square yard to maintain friction. Coring showed that the HMWM resin penetrated the cracks more than two inches deep. Testing of the treated deck yielded Friction Numbers averaging 33 with a treaded tire compared to 36 prior to treatment. An inspection soon after treatment found five leaky cracks in one of the 15 spans. One inspection during a steady rain showed no leakage, but leakage from numerous cracks occurred during a subsequent rain. A second HMWM application was made on two spans. Leakage through the double application occurred during a rain. Neither the single or double application were successful in preventing leakage through the cracks.

Evaluation of Cover Aggregate Stripping Characteristics, HR-182, 1979

The purpose of Research Project HR-182 was to identify those aggregate types which would perform satisfactorily as seal coat aggregates. Aggregates were chosen from across the State to represent the various types normally encountered and were used with two different types of binder bitumens. A water spray treatment was also included to simulate the effects of rainfall. The evaluation was based upon aggregate retention. Due to the influence of unexpected variables upon the field samples, the laboratory data are reliable for only the most general observations. Namely, that gravels as a group appear to be retained better than carbonates and rain-fall shortly after seal coat placement can affect aggregate retention. The subsequent field observations and analysis of skid resistance data permit the following conclusions: 1. Aggregate retention is influenced by lithologic type with the gravels, quartzite, haydite, dolomites, and medium grained limestones performing best. 2. Aggregate retention is not influenced by binder bitumen type. 3. Friction values of seal coats are influ-enced by aggregate retention and/or lithologic type. The following recommendations have been determined: The aggregate used for cover aggregate/seal coat projects should be Type 4 or better skid resistance as identified in Iowa DOT Materials Instructional Memorandum T-203. This will result in maximizing the possibility of good aggregate retention and skid resistance.

Development of an Economic Dust Palliative for Limestone Surfaced Secondary Roads, HR-297, 1990

This research project was directed at laboratory and field evaluation of sodium montmorillonite clay (bentonite) as a dust palliative for limestone surfaced secondary roads. It had been postulated that the electrically charged surfaces of the clay particles could interact with the charged surfaces of the limestone and act as a bonding agent to agglomerate fine (-#200) particulates and also to band the fine particulates to larger (+#200) limestone particles. Laboratory testing using soda ash dispersed bentonite treatment of limestone fines indicated significant improvement of compressive strength and slaking characteristics. It was recommended that the project proceed to field trials and test roads were constructed in Dallas and Adair counties in Iowa. Soda ash dispersed bentonite solutions can be field mixed and applied with conventional spray distribution equipment. A maximum of 1.5% bentonite(by weight of aggregate)can be applied at one time. Higher applications would have to be staged allowing the excess moisture to evaporate between applications. Construction of higher application treatments can be accomplished by adding dry bentonite to the surfacing material and then by dry road mixing. The soda ash water solution can then be spray applied and the treated surfacing material wet mixed by motor graders to a consistency of 3 to 4 inch slump concrete. Two motor graders working in tandem can provide rapid mixing for both methods of construction. Calcium and magnesium chloride treatments are 2 to 3 times more effective in dust reduction in the short term (3-4 months) but are prone to washboarding and potholing due to maintenance restrictions. Bentonite treatment at the 2-3% level is estimated to provide a 30-40% dust reduction over the long term(18-24 months). Normal maintenance blading operations can be used on bentonite treated areas. Vehicle braking characteristics are not adversely affected up to the 3.0% treatment level. The bentonite appears to be functioning as a banding agent to bind small particulates to larger particles and is acting to agglomerate fine particles of limestone. This bonding capability appears recoverable from environmental effects of winter, and from alternating wet and dry periods. The bentonite appears to be able to interact with new applications of limestone maintenance material and maintains a dust reduction capability. Soda ash dispersed bentonite treatment is approximately 10 times more cost effective per percent dust reduction than conventional chloride treatments with respect to time. However,the disadvantage is that there is not the initial dramatic reduction in dust generation as with the chloride treatment. Although dust is reduced 30-40% after treatment there is still dust being generated and the traveling public or residents may not perceive the reduction.

Bentonite Treatment for Economical Dust Reduction on Limestone Surfaced Secondary Roads, HR-351, 1995

This research project was directed at laboratory and field evaluation of sodium montmorillonite clay (Bentonite) as a dust palliative for limestone surfaced secondary roads. It was postulated that the electrically charged surfaces (negative) of the clay particles could interact with the charged surfaces (positive) of the limestone and act as a bonding agent to agglomerate fine (-#200) particulates, and also to bond the fine particulates to larger (+#200) limestone particles. One mile test roads were constructed in Tama, Appanoose, and Hancock counties in Iowa using Bentonite treatment levels (by weight of aggregate) ranging from 3.0 to 12.0%. Construction was accomplished by adding dry Bentonite to the surfacing material and then dry road mixing. The soda ash/water solution (dispersing agent) was spray applied and the treated surfacing material wet mixed by motor graders to a consistency of 2 to 3 inch slump concrete. Two motor graders working in tandem provided rapid mixing. Following wet mixing the material was surface spread and compacted by local traffic. Quantitative and qualitative periodic evaluations and testing of the test roads was conducted with respect to dust generation, crust development, roughness, and braking characteristics. As the Bentonite treatment level increased dust generation decreased. From a cost/benefit standpoint, an optimum level of treatment is about 8% (by weight of aggregate). For roads with light traffic, one application at this treatment level resulted in a 60-70% average dust reduction in the first season, 40-50% in the second season, and 20-30% in the third season. Crust development was rated at two times better than untreated control sections. No discernible trend was evident with respect to roughness. There was no evident difference in any of the test sections with respect to braking distance and braking handling characteristics, under wet surface conditions compared to the control sections. Chloride treatments are more effective in dust reduction in the short term (3-4 months). Bentonite treatment is capable of dust reduction over the long term (2-3 seasons). Normal maintenance blading operations can be used on Bentonite treated areas. Soda ash dispersed Bentonite treatment is estimated to be more than twice as cost effective per percent dust reduction than conventional chloride treatments, with respect to time. However, the disadvantage is that there is not the initial dramatic reduction in dust generation as with the chloride treatment. Although dust is reduced significantly after treatment there is still dust being generated. Video evidence indicates that the dust cloud in the Bentonite treated sections does not rise as high, or spread as wide as the cloud in the untreated section. It also settles faster than the cloud in the untreated section. This is considered important for driving safety of following traffic, and for nuisance dust invasion of residences and residential areas. The Bentonite appears to be functioning as a bonding agent.

The cost effectiveness of pharmacological smoking cessation therapies in developing countries: a case study in the Seychelles

OBJECTIVE: To examine the incremental cost effectiveness of the five first line pharmacological smoking cessation therapies in the Seychelles and other developing countries. DESIGN: A Markov chain cohort simulation. SUBJECTS: Two simulated cohorts of smokers: (1) a reference cohort given physician counselling only; (2) a treatment cohort given counselling plus cessation therapy. INTERVENTION: Addition of each of the five pharmacological cessation therapies to physician provided smoking cessation counselling. MAIN OUTCOME MEASURES: Cost per life-year saved (LYS) associated with the five pharmacotherapies. Effectiveness expressed as odds ratios for quitting associated with pharmacotherapies. Costs based on the additional physician time required and retail prices of the medications. RESULTS: Based on prices for currently available generic medications on the global market, the incremental cost per LYS for a 45 year old in the Seychelles was 599 US dollars for gum and 227 dollars for bupropion. Assuming US treatment prices as a conservative estimate, the incremental cost per LYS was significantly higher, though still favourable in comparison to other common medical interventions: 3712 dollars for nicotine gum, 1982 dollars for nicotine patch, 4597 dollars for nicotine spray, 4291 dollars for nicotine inhaler, and 1324 dollars for bupropion. Cost per LYS increased significantly upon application of higher discount rates, which may be used to reflect relatively high opportunity costs for health expenditures in developing countries with highly constrained resources and high overall mortality. CONCLUSION: Pharmacological cessation therapy can be highly cost effective as compared to other common medical interventions in low mortality, middle income countries, particularly if medications can be procured at low prices.

Liquid chromatography - Mass spectrometry

In this article, selected examples of applications of liquid chromatography coupled to mass spectrometry are given. The examples include the analysis of i) impurities in manufactured, pharmaceutical or synthesis products, ii) polyphenols in natural products, and iii) phytohormones in plant extracts. Finally, examples of applications of molecular characterization via flow injection analysis by electron spray ionization mass spectrometry (ESI-MS) are also given.

Comparison of microscopic method and computational program for pesticide deposition evaluation of spraying

The main objective of this work was to compare two methods to estimate the deposition of pesticide applied by aerial spraying. Hundred and fifty pieces of water sensitive paper were distributed over an area of 50 m length by 75 m width for sampling droplets sprayed by an aircraft calibrated to apply a spray volume of 32 L/ha. The samples were analysed by visual microscopic method using NG 2 Porton graticule and by an image analyser computer program. The results reached by visual microscopic method were the following: volume median diameter, 398±62 mum; number median diameter, 159±22 mum; droplet density, 22.5±7.0 droplets/cm² and estimated deposited volume, 22.2±9.4 L/ha. The respective ones reached with the computer program were: 402±58 mum, 161±32 mum, 21.9±7.5 droplets/cm² and 21.9±9.2 L/ha. Graphs of the spatial distribution of droplet density and deposited spray volume on the area were produced by the computer program.

Phytochemical investigation of alpine plants : the cottonsedges Eriophorum scheuchzeri Hoppe, E. angustifolium Honck. and E. latifolium Hoppe (CYPERACEAE)

Résumé: Alpine plants living at high altitudes undergo a series of climatic stress factors (chilling, enhanced UV radiation, short growing season, low nutriment supply...) which may influence their secondary compounds composition. Many publications showed in these last years that plants under stress conditions do synthesize a range of specific defence compounds (terpenes, flavonoids, coumarines...). A careful phytochemical investigation of those plants could therefore lead to the discovery of active molecules. Thus, for the biological and chemical screening, about 30 alpine plants have been collected above 2000 metres, in the alpine grass-lands. Eriophorum scheuchzeri Hoppe (Cyperaceae), not yet investigated phytochemically, revealed in its lipophilic and polar extracts the presence of various radical scavengers in a TLC autography with the DPPH (2,2-dipheny1-1- picrylhydrazyl) radical as spray reagent, as well as several antifungal compounds acitve against Cladosporium cucumerinum and Candida albi cans. The first part of this study consisted in the detection, isolation and characterization of the bioactive natural compounds present in the lipophilic extract of Eriophorum scheuchzeri. Among the eight isolated compounds, six were isoflavones. No isoflavones have been reported in the Cyperaceae family yet, nor in related families such as Poaceae or Juncaceae. Besides, isoflavones are generally rare in the plant kingdom and and they occur only in some families, such as Fabaceae, Rosaceae or Myristicaceae. In addition, out of these six isoflavones, three were new isoflavones. The known compounds were parvisoflavone A and B and cajanin which are already known isoflavones in the Fabaceae family. Two of the new isoflavones were particular, as they were C-methylated on the B-ring at the C-3' position. Methylated flavonoids are particularly rare in the plant kingdom. At present, no C-methylated isoflavones with methyl groups on the B-ring have ever been reported. The fourth new compound was a prenylated flavanone. Flavanones are also rare in the Cyperaceae family since they were found only in two genera (Cyperus and Schoenus). Finally, the widespread flavone tricin, characteristic of the Cyperaceae and Poaceae family has also been isolated. The second part of this study consisted in the characterization of the polar components present in the Me0H extract. In order to obtain mass and UV information about the secondary compounds present in the Eriophorum scheuchzeri methanolic extract, a LC-UV/DAD-APCl/MSn analysis has been performed as a first dereplication step. The UV/DAD spectra showed the presence of polyphenol compounds (phenylpropanoids and flavonoids). The LC-APCI/MSn analysis allowed the determination of the molecular weight of these compounds. Moreover, the fragmentation pattern of the [M+H]+ ions indicated presence of mono-, di- and tri-glycosides. LC-UV in combination with UV shift reagents added post-column was used in a second phase for the structural elucidation of the flavonoids. It allowed the positioning of the sugars on the aglycones. Finally, LC-NMR was used for a more detailed structural investigation of the compounds present in the crude MEOH extract. Thus, 10 fiavonoids have been totally or partially characterized by LC-UV-MS and LC-1H-RMN and UV-shift reagents added post column. However, the information obtained on-line was not always sufficient to allow a complete identification of all the compounds. Some of these compounds especially those with more than two sugar units attached to them, have been isolated in order to proceed to their complete characterization. Moreover, the Eriophorum scheuchzeri species was compared to two other species from the same genus. A LC-UV-ESI/MS analysis enabled a survey of the chemical composition of the DCM extracts of two related species E. angustifolium (Honck) and E. latifolium (Hoppe). The chromatograms of the three species showed some similarities in their flavonoid contents, especially by the recurrent presence of three compounds. The MEOH extracts of all three species have been compared by means of LC-UV-APCl/MS analyses. The chromatographic profile of all the three species showed even closer similarities than those found in the DCM extracts. E. angustifolium Honck. and E. latifolium species showed 7 compounds in common. Finally, the pure compounds obtained from the DCM (CH2Cl2) fraction were tested at different concentration, in order to evaluate their chemical and biological activities. All eight compounds showed an anti-scavenger activity against the DPPH radical, and four compounds showed antifungal activities against Cladosporium cucumerinum and Candida albicans. The pure compounds isolated from the MeOH extract were tested only for their biological activities as their antioxidant activity is already well documented in the literature. No compound showed a biological activity against Cladosporium cucumerinum and Candida albicans. Résumé: De nombreux travaux ont démontré ces dernières décennies que les plantes soumises à différents types de stress (basse température, UV, stress hydrique) synthétisent des composés secondaires (fiavonoides, coumarines, terpènes...) de protection et de défense. Les plantes d'altitude par exemple qui sont exposées à des conditions climatiques et environnementales difficiles, ont tendance à synthétiser des substances antioxydantes et antiradicalaires. Une investigation phytochirnique de ces plantes a conduit à la découverte de nouvelles molécules actives. Ainsi plusieurs plantes alpines ont été sélectionnées en fonction de leur habitat en vue de les soumettre aux tests biologiques (antifongiques) et chimiques (antiradicalaires) menés en routine dans notre laboratoire. Dans ce criblage biologique préliminaire, les extraits d'Eriophorum scheuchzeri Hoppe (Cyperaceae) ont réagi positivement aux différents tests. Il a donc été décidé d'entreprendre l'isolement des composés actifs. La première partie de ce travail a consisté à détecter, isoler et caractériser les composés naturels actifs présents dans l'extrait apolaire d' Eriophorum scheuchzeri. Parmi les huit composés isolés, quatre d'entre eux sont nouveaux. Un de ces produits est une flavanone et trois sont de nouvelles isoflavones, particulièrement intéressantes car elles possèdent des groupements C-méthylés au niveau du cycle B. Les flavonoides C-méthylés sont peu répandus dans le règne végétal et les rares exemples connus sont généralement C-méthylés sur le cycle A. Les quatre autres composés isolés n'ont jamais été décrits dans cette famille. Il s'agit d' isoflavones, les parvisoflavones A et B et la cajanine. Enfin, la flavone tricine, flavonoide caractéristique des Cyperaceae et des Poaceae a également été isolée. La deuxième partie de ce travail a consisté à caractériser les constituants polaires présents dans l'extrait methanolique. L'extrait a été analysé par chromatographie analytique couplée à différentes méthodes spectroscopiques (LC-UV-MS et LC-UV-1H RMN). De cette façon, douze flavonoides et un dérivé du phénylpropane, l'acide chlorogénique ont été identifiés. Les flavonoides tri-glycosylés ont dû être isolés afin de déterminer la nature et l'enchaînement des sucres. Finalement, l'espèce Eriophorum scheuchzeri a été comparée à deux autres espèces d' Eriophorum, soit E. angustifolium et E. latifolium. En conclusion, cette étude phytochimique a abouti à l'isolement de plusieurs nouvelles isoflavones aux activités antioxydantes et antifongiques ainsi qu'oestrogéniques.

Effects of intranasal administration of synthetic (4-28)human atrial natriuretic peptide to normal volunteers.

The effects of intranasal administration of increasing doses of synthetic human natriuretic peptide (4-28 hANP) were studied in six healthy volunteers. The peptide was administered as a nasal spray at doses of 50, 100, 200, and 500 micrograms in ascending order at 48-h intervals. Vehicle was administered by the same route randomly between any two of the doses. Intranasal hANP administration had no effect on either blood pressure, heart rate (HR), or hematocrit. Diuresis did not change consistently, whereas natriuresis tended to rise with vehicle as well as with hANP administration. This was attributed to the infusion of isotonic saline during the experiment. There was no significant increase in plasma ANP levels after intranasal administration of any of the different doses. Thus, no evidence that the atrial natriuretic peptide tested (4-28 hANP) can cross the nasal mucosal barrier was found.

RFID Tags for Detecting Concrete Degradation in Bridge Decks, RB08-011, 2013

Steel reinforcing bar (rebar) corrosion due to chlorine ingress is the primary degradation mechanism for bridge decks. In areas where rock salt is used as a de-icing agent, salt water seeps into the concrete through cracks, causing corrosion of the rebar and potentially leading to catastrophic failure if not repaired. This project explores the use of radio frequency identification (RFID) tags as low-cost corrosion sensors. RFID tags, when embedded in concrete, will fail due to corrosion in the same manner as rebar after prolonged exposure to salt water. In addition, the presence of salt water interferes with the ability to detect the tags, providing a secondary mechanism by which this method can work. During this project, a fieldable RFID equipment setup was constructed and tested. In addition to a number of laboratory experiments to validate the underlying principles, RFID tags were embedded and tested in several actual bridge decks. Two major challenges were addressed in this project: issues associated with tags not functioning due to being in close proximity to rebar and issues associated with portland concrete coming in direct contact with the tags causing a detuning effect and preventing the tags from operating properly. Both issues were investigated thoroughly. The first issue was determined to be a problem only if the tags are placed in close proximity to rebar. The second issue was resolved by encapsulating the tag. Two materials, polyurethane spray foam and extruded polystyrene, were identified as providing good performance after testing, both in the lab and in the field.

Drying rates of Rubi grapes submitted to chemical pretreatments for raisin production

The objective of this work was to determine the most appropriated chemical treatment to be used to dry grapes cv. Rubi for raisin production. Drying curves for convective drying with air at 50ºC, in a tray drier, were obtained for grapes submitted to chemical pretreatments with different concentrations of potassium carbonate and olive oil, and different dipping times, according to factorial designs. Convective drying curves were also obtained for grapes pretreated in aqueous suspensions of soybean lecithin, at varied lecithin concentrations and dipping times. Page model was adjusted to the experimental drying curves, and the calculated drying times showed that the best pretreatment consisted in dipping grapes for 2 minutes in a 5% olive oil and 6% K2CO3 emulsion, at 50ºC, which resulted in a drying time close to that of the pretreatment with 2.5% of olive oil, but with a lower consumption of this substance. In addition, the immersion of grapes in an aqueous suspension of 2% soy lecithin, at 50ºC, for 5 minutes, resulted in a total drying time slightly higher than the most effective pretreatment.

Acute respiratory syndrome after inhalation of waterproofing sprays: a posteriori exposure-response assessment in 102 cases

Waterproofing agents are widely used to protect leather and textiles in both domestic and occupational activities. An outbreak of acute respiratory syndrome following exposure to waterproofing sprays occurred during the winter 2002-2003 in Switzerland. About 180 cases were reported by the Swiss Toxicological Information Centre between October 2002 and March 2003, whereas fewer than 10 cases per year had been recorded previously. The reported cases involved three brands of sprays containing a common waterproofing mixture, that had undergone a formulation change in the months preceding the outbreak. A retrospective analysis was undertaken in collaboration with the Swiss Toxicological Information Centre and the Swiss Registries for Interstitial and Orphan Lung Diseases to clarify the circumstances and possible causes of the observed health effects. Individual exposure data were generated with questionnaires and experimental emission measurements. The collected data was used to conduct numeric simulation for 102 cases of exposure. A classical two-zone model was used to assess the aerosol dispersion in the near- and far-field during spraying. The resulting assessed dose and exposure levels obtained were spread on large scales, of several orders of magnitude. No dose-response relationship was found between exposure indicators and health effects indicators (perceived severity and clinical indicators). Weak relationships were found between unspecific inflammatory response indicators (leukocytes, C-reactive protein) and the maximal exposure concentration. The results obtained disclose a high interindividual response variability and suggest that some indirect mechanism(s) predominates in the respiratory disease occurrence. Furthermore, no threshold could be found to define a safe level of exposure. These findings suggest that the improvement of environmental exposure conditions during spraying alone does not constitute a sufficient measure to prevent future outbreaks of waterproofing spray toxicity. More efficient preventive measures are needed prior to the marketing and distribution of new waterproofing agents.

Portland Cement Concrete Curing Compound Performance Phase I and Phase II, MLR-02-03, 2003

Testing the efficiency of Portland Cement Concrete (PCC) curing compounds is currently done following Test Method Iowa 901-D, May 2002. Concrete test specimens are prepared from mortar materials and are wet cured 5 hours before the curing compound is applied. All brands of curing compound submitted to the Iowa Department of Transportation are laboratory tested for comparative performance under the same test conditions. These conditions are different than field PCC paving conditions. Phase I tests followed Test Method Iowa 901-D, but modified the application amounts of the curing compound. Test results showed that the application of two coats of one-half thickness each increased efficiency compared to one full thickness coat. Phase II tests also used the modified application amounts, used a concrete mix (instead of a mortar mix) and applied curing compound a few minutes after molding. Measurements of losses, during spraying of the curing compound, were noted and were found to be significant. Test results showed that application amounts, testing techniques, concrete specimen mix design and spray losses do influence the curing compound efficiency. The significance of the spray losses indicates that the conventional test method being used (Iowa 901 D) should be revised.