Model based analysis of the post-combustion calcium looping process for carbon dioxide capture

This thesis presents a one-dimensional, semi-empirical dynamic model for the simulation and analysis of a calcium looping process for post-combustion CO2 capture. Reduction of greenhouse emissions from fossil fuel power production requires rapid actions including the development of efficient carbon capture and sequestration technologies. The development of new carbon capture technologies can be expedited by using modelling tools. Techno-economical evaluation of new capture processes can be done quickly and cost-effectively with computational models before building expensive pilot plants. Post-combustion calcium looping is a developing carbon capture process which utilizes fluidized bed technology with lime as a sorbent. The main objective of this work was to analyse the technological feasibility of the calcium looping process at different scales with a computational model. A one-dimensional dynamic model was applied to the calcium looping process, simulating the behaviour of the interconnected circulating fluidized bed reactors. The model incorporates fundamental mass and energy balance solvers to semi-empirical models describing solid behaviour in a circulating fluidized bed and chemical reactions occurring in the calcium loop. In addition, fluidized bed combustion, heat transfer and core-wall layer effects were modelled. The calcium looping model framework was successfully applied to a 30 kWth laboratory scale and a pilot scale unit 1.7 MWth and used to design a conceptual 250 MWth industrial scale unit. Valuable information was gathered from the behaviour of a small scale laboratory device. In addition, the interconnected behaviour of pilot plant reactors and the effect of solid fluidization on the thermal and carbon dioxide balances of the system were analysed. The scale-up study provided practical information on the thermal design of an industrial sized unit, selection of particle size and operability in different load scenarios.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Suomen satamissa käsiteltävät pakatut vaaralliset aineet ja esimerkkejä niiden vaaraominaisuuksista

Tämä raportti on tehty osana Kymenlaakson ammattikorkeakoulun hallinnoiman NELIn (North European Logistics Institute) esiselvitystä vaarallisten aineiden tunnistamisesta konttiliikenteessä. Tässä Turun yliopiston merenkulkualan koulutus- ja tutkimuskeskuksen Kotkassa toimivan Merenkulun logistiikan tutkimus -yksikön tekemässä selvityk-sessä on tutkittu kansallista satamaliikenteen PortNet-järjestelmää hyödyntäen, mitä pakattuina kuljetettavia vaarallisia aineita ja kuinka suuria määriä Suomen satamissa käsitellään. PortNet-analyysin tulosten pohjalta tutkimuksessa on selvitetty Suomen satamissa eniten käsiteltyjen, pakattuina kuljetettavien vaarallisten aineiden vaaraominaisuuksia sekä ihmisten että ympäristön kannalta. Tutkimuksessa tehdyn PortNet-analyysin perusteella pakattuja vaarallisia aineita käsiteltiin 16:ssa Suomen satamassa vuonna 2012. Käsiteltyjen aineiden kokonaismäärä oli noin 820 000 tonnia, josta viennin osuus oli 53 % ja tuonnin 47 %. Eniten kuljetettuja IMDG-luokkia olivat luokan 3 palavat nesteet (31 %:n osuus), luokan 9 muut vaaralliset aineet ja esineet (25 %) sekä luokan 8 syövyttävät aineet (23 %). Muiden luokkien osuus oli alle 10 %. Suomen satamissa käsiteltiin vuonna 2012 yhteensä noin 1 020 eri-laista, pakattua vaarallista ainetta. Yli 10 000 tonnia käsiteltyjä aineita oli yhteensä 16, 1 000–10 000 tonnia käsiteltyjä aineita 84, 100–1 000 tonnia käsiteltyjä aineita 148 ja alle 100 tonnia käsiteltyjä aineita noin 770. Eniten käsiteltyjä aineita olivat pääasiassa erilaiset aineyhdisteet ja tarkemmin määrittelemättömät aineet, kuten ympäristölle vaarallinen aine n.o.s, maalit, polymeeripelletit, hartsiliuos, kohotetussa lämpötilassa oleva neste n.o.s. ja nikkelimetallihybridiakut. Näitä kaikkia käsiteltiin Suomen satamissa yli 20 000 tonnia vuonna 2012. Varsinaisista yksittäisistä vaarallisista aineista eniten käsiteltyjä olivat muurahaishappo, vetyperoksidin vesiliuos, natriumkloraatti, ammoniumnitraatti, fenoli ja kloorietikkahappoliuos. Näitä kaikkia käsiteltiin yli 10 000 tonnia vuonna 2012. PortNet-analyysin tulosten pohjalta valittiin kymmenen ainetta, joiden vaaraominaisuuksia sekä ihmisten että ympäristön kannalta tarkasteltiin tarkemmin. Tarkasteluun valittiin, tieteellistä harkintaa käyttäen, eniten kuljetettavia vaarallisia yksittäisiä kemikaaleja. Tarkasteluun valitut kemikaalit olivat muurahaishappo, vetyperoksidi, natrium-kloraatti, kloorietikkahappo, fenoli, akryyliamidiliuos, ksyleenit, akryylinitriili, tolueeni ja epikloorihydriini. Tutkituista kemikaaleista ympäristölle haitallisimpia ovat fenoli, kloorietikkahappo ja akryyliamidiliuos. Ihmisen kannalta kaikki 10 tutkittua kemikaalia muodostavat onnettomuustilanteessa riskin ihmisten terveydelle joko syövyttävyytensä, reaktiivisuutensa tai myrkyllisyytensä vuoksi. Osa kemikaaleista voi aiheuttaa ihmisille myös kroonisia haittoja, kuten kohonnutta syöpäriskiä tai muutoksia perimässä, joko suurina kerta-annoksina tai pieninä toistuvina pitoisuuksina. Suomen satamissa käsiteltävien pakattujen kemikaalien erilaisuus ja suuri lukumäärä tekevät niistä vaikeasti hallittavissa olevan riskitekijän. Yleisesti ottaen voidaan sanoa, että pakatuista kemikaaleista aiheutuu pienehköissä vuototilanteissa suurempi uhka ihmisen terveydelle kuin ympäristölle, kun taas irtolastikuljetuksissa tapahtuvien onnettomuuksien yhteydessä vuotaneen aineen määrä on yleensä suurempi ja näin ollen myös ympäristölle koituva uhka voi olla suuri.

GIS assessing traditional and modern agricultural land use/land cover change. A case study 1959-2005: Rekijoki, Somero, SW-Finland

Finland’s rural landscape has gone through remarkable changes from the 1950’s, due to agricultural developments. Changed farming practices have influenced especially traditional landscape management, and modifications in the arable land structure and grasslands transitions are notable. The review of the previous studies reveal the importance of the rural landscape composition and structure to species and landscape diversity, whereas including the relevance in presence of the open ditches, size of the field and meadow patches, topology of the natural and agricultural landscape. This land-change study includes applying remote sensed data from two time series and empirical geospatial analysis in Geographic Information Systems (GIS). The aims of this retrospective research is to detect agricultural landscape use and land cover change (LULCC) dynamics and discuss the consequences of agricultural intensification to landscape structure covering from the aspects of landscape ecology. Measurements of LULC are derived directly from pre-processed aerial images by a variety of analytical procedures, including statistical methods and image interpretation. The methodological challenges are confronted in the process of landscape classification and combining change detection approaches with landscape indices. Particular importance is paid on detecting agricultural landscape features at a small scale, demanding comprehensive understanding of such agroecosystems. Topological properties of the classified arable land and valley are determined in order to provide insight and emphasize the aspect the field edges in the agricultural landscape as important habitat. Change detection dynamics are presented with change matrix and additional calculations of gain, loss, swap, net change, change rate and tendencies are made. Transition’s possibility is computed following Markov’s probability model and presented with matrix, as well. Thesis’s spatial aspect is revealed with illustrative maps providing knowledge of location of the classified landscape categories and location of the dynamics of the changes occurred. It was assured that in Rekijoki valley’s landscape, remarkable changes in landscape has occurred. Landscape diversity has been strongly influenced by modern agricultural landscape change, as NP of open ditches has decreased and the MPS of the arable plot has decreased. Overall change in the diversity of the landscape is determined with the decrease of SHDI. Valley landscape considered as traditional land use area has experienced major transitional changes, as meadows class has lost almost one third of the area due to afforestation. Also, remarkable transitions have occurred from forest to meadow and arable land to built area. Boundaries measurement between modern and traditional landscape has indicated noticeable proportional increase in arable land-forest edge type and decrease in arable land-meadow edge type. Probability calculations predict higher future changes for traditional landscape, but also for arable land turning into built area.

Uusiutuvan energian käyttömahdollisuudet Liikuntakeskus Pajulahdessa

Tämä diplomityö on tehty Lappeenrannan teknillisen yliopiston, Liikuntakeskus Pajulahden ja Nastolan Energiasäätiön yhteisprojektina. Työn tarkoituksena on tutkia aurinkosähköjärjestelmien taloudellista kannattavuutta ostosähkön korvaamisessa Liikuntakeskus Pajulahden kiinteistössä. Työssä tehdään laskelmat aurinkopaneelien tuotoista, tuotetun sähkön hinnasta, investointien takaisinmaksuajoista sekä tuotetun aurinkosähkön synnyttämistä hiilidioksidipäästövähenemistä. Lisäksi tarkastellaan energiaveron vaikutusta pientuotantolaitoksen kannattavuuteen. Tämän hetkisillä aurinkosähköjärjestelmien hinnoilla pystytään tuottamaan puhdasta, ympäristöystävällistä sähköä kilpailukykyiseen hintaan. Työssä tehdään yleiskatsaus myös muiden uusiutuviin energialähteisiin perustuvien tuotantomenetelmien käyttömahdollisuuksista. Yhtenä erityistarkastelunkohteena on Pajulahden monitoimihalliin vuonna 2008 suunniteltu vesistöä lämmönlähteenä käyttävä lämpöpumppujärjestelmä, jonka toteutukseen ei saatu tarvittavia lupia. Tarkastelussa tutkitaan myös aiemmin Suomessa toteutettuja vastaavia hankkeita ja niiden lupien saantia. Lisäksi on haettu tosiasioihin perustuvia argumentteja keskusteluun vesistölämmön hyödyntämisestä. Tarkastelun kohteena oleva vesistölämpöhanke voidaan todeta olevan erittäin kannattava, taloudellisesti sekä ympäristöllisesti. Tutkimuksen pohjalta Nastolan Energiasäätiölle tuotetaan havainnollinen ja selkeä aineisto aurinkoenergian hyödyntämismahdollisuuksista Nastolan kunnassa.

B2SHARE – Storing and Sharing Research Data

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

B2SHARE – Storing and Sharing Research Data

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Species composition and biogeographic relations of the rock outcrop flora on the high plateau of Itatiaia, SE-Brazil

We studied the flora of vegetation islands on rock outcrops on the Itatiaia Plateau (22°21'S and 44°40'W), at 2,400 m.a.s.l. A total of 114 vascular plant species, which correspond to ca. 20%-25% of the currently inventoried flora of the plateau, were sampled in 197 small vegetation islands (total area of 0.034 ha). Xerophytes and hydrophytes were often found side by side due to environmental heterogeneity at a small scale, explaining in part the high species diversity. Rock outcrops may support floras quite distinct from those in neighbouring habitats, due to the action of strong environmental filters, but in Itatiaia the geographic distribution patterns among rupicolous plants appear to mimic those described for the whole flora around it, with 15.1% of narrow endemic species and six strictly rupicolous plants. Underlining the "temperate" nature of the high elevation climate in Itatiaia, the sampled flora was dominated by species of the families Asteraceae and Poaceae, and the number of CAM (crassulacean acid metabolism) species was very low. A few endemic species of tropical origin - Pleurostima gounelleana (Beauv.) Men. (Velloziaceae) and Fernseea itatiaiae (Wawra) Baker (Bromeliaceae) - play a crucial role in this vegetation, as pioneer mat-formers facilitating later establishment of numerous other species. Hemicryptophytes prevail in the sampled flora, while therophytes are exceptionally rare and mainly consist of opportunistic species associated with disturbances. Numerous microhabitats and strong environmental gradients in these high elevation rock outcrops afford opportunities for establishment of a highly diversified flora. These island-like environments may represent an important refuge for grassland species from fire and other disturbances in the surrounding grasslands.

Biogas production in regional integrated biodegradable waste treatment – Possibilities for improving energy performance and reducing GHG emissions

The greatest threat that the biodegradable waste causes on the environment is the methane produced in landfills by the decomposition of this waste. The Landfill Directive (1999/31/EC) aims to reduce the landfilling of biodegradable waste. In Finland, 31% of biodegradable municipal waste ended up into landfills in 2012. The pressure of reducing disposing into landfills is greatly increased by the forthcoming landfill ban on biodegradable waste in Finland. There is a need to discuss the need for increasing the utilization of biodegradable waste in regional renewable energy production to utilize the waste in a way that allows the best possibilities to reduce GHG emissions. The objectives of the thesis are: (1) to find important factors affecting renewable energy recovery possibilities from biodegradable waste, (2) to determine the main factors affecting the GHG balance of biogas production system and how to improve it and (3) to find ways to define energy performance of biogas production systems and what affects it. According to the thesis, the most important factors affecting the regional renewable energy possibilities from biodegradable waste are: the amount of available feedstock, properties of feedstock, selected utilization technologies, demand of energy and material products and the economic situation of utilizing the feedstocks. The biogas production by anaerobic digestion was seen as the main technology for utilizing biodegradable waste in agriculturally dense areas. The main reason for this is that manure was seen as the main feedstock, and it can be best utilized with anaerobic digestion, which can produce renewable energy while maintaining the spreading of nutrients on arable land. Biogas plants should be located close to the heat demand that would be enough to receive the produced heat also in the summer months and located close to the agricultural area where the digestate could be utilized. Another option for biogas use is to upgrade it to biomethane, which would require a location close to the natural gas grid. The most attractive masses for biogas production are municipal and industrial biodegradable waste because of gate fees the plant receives from them can provide over 80% of the income. On the other hand, directing gate fee masses for small-scale biogas plants could make dispersed biogas production more economical. In addition, the combustion of dry agricultural waste such as straw would provide a greater energy amount than utilizing them by anaerobic digestion. The complete energy performance assessment of biogas production system requires the use of more than one system boundary. These can then be used in calculating output–input ratios of biogas production, biogas plant, biogas utilization and biogas production system, which can be used to analyze different parts of the biogas production chain. At the moment, it is difficult to compare different biogas plants since there is a wide variation of definitions for energy performance of biogas production. A more consistent way of analyzing energy performance would allow comparing biogas plants with each other and other recovery systems and finding possible locations for further improvement. Both from the GHG emission balance and energy performance point of view, the energy consumption at the biogas plant was the most significant factor. Renewable energy use to fulfil the parasitic energy demand at the plant would be the most efficient way to reduce the GHG emissions at the plant. The GHG emission reductions could be increased by upgrading biogas to biomethane and displacing natural gas or petrol use in cars when compared to biogas CHP production. The emission reductions from displacing mineral fertilizers with digestate were seen less significant, and the greater N2O emissions from spreading digestate might surpass the emission reductions from displacing mineral fertilizers.

A single-step purification of bothropstoxin-1

Bothrops venoms are complex mixtures of components with a wide range of biological activities. Among these substances, myotoxins have been investigated by several groups. Bothropstoxin-1 (Bthtx-1) is a phospholipase A2-like basic myotoxin from Bothrops jararacussu. The purification of this component involves two chromatographic steps. Although providing a pure material, the association of these two steps is time consuming and a single-step method using high performance chromatography media would be useful. In the present study, we describe a single-step purification method for Bthtx-1. Bothrops jararacussu venom was dissolved in 1 ml buffer. After centrifugation, the supernatant was injected into a Resource-S cation exchange column connected to an FPLC system and eluted with a linear salt gradient. The complete procedure took 20 min, representing a considerable time gain when compared to a previously described method (Homsi-Brandenburgo MI et al. (1988) Toxicon, 26: 615-627). Bthtx-1 purity and identity, assessed by SDS-PAGE and N-terminal sequencing, resulted in a single band with a molecular mass of about 14 kDa and the expected sequence of the first 5 residues, S-L-F-E-L. Although the amount of protein purified after each run is lower than in the previously described method, we believe that this method may be useful for small-scale purifications.

Heterogeneous mass transfer in fluidized beds by computational fluid dynamics

The main objective of this research is to estimate and characterize heterogeneous mass transfer coefficients in bench- and pilot-scale fluidized bed processes by the means of computational fluid dynamics (CFD). A further objective is to benchmark the heterogeneous mass transfer coefficients predicted by fine-grid Eulerian CFD simulations against empirical data presented in the scientific literature. First, a fine-grid two-dimensional Eulerian CFD model with a solid and gas phase has been designed. The model is applied for transient two-dimensional simulations of char combustion in small-scale bubbling and turbulent fluidized beds. The same approach is used to simulate a novel fluidized bed energy conversion process developed for the carbon capture, chemical looping combustion operated with a gaseous fuel. In order to analyze the results of the CFD simulations, two one-dimensional fluidized bed models have been formulated. The single-phase and bubble-emulsion models were applied to derive the average gas-bed and interphase mass transfer coefficients, respectively. In the analysis, the effects of various fluidized bed operation parameters, such as fluidization, velocity, particle and bubble diameter, reactor size, and chemical kinetics, on the heterogeneous mass transfer coefficients in the lower fluidized bed are evaluated extensively. The analysis shows that the fine-grid Eulerian CFD model can predict the heterogeneous mass transfer coefficients quantitatively with acceptable accuracy. Qualitatively, the CFD-based research of fluidized bed process revealed several new scientific results, such as parametrical relationships. The huge variance of seven orders of magnitude within the bed Sherwood numbers presented in the literature could be explained by the change of controlling mechanisms in the overall heterogeneous mass transfer process with the varied process conditions. The research opens new process-specific insights into the reactive fluidized bed processes, such as a strong mass transfer control over heterogeneous reaction rate, a dominance of interphase mass transfer in the fine-particle fluidized beds and a strong chemical kinetic dependence of the average gas-bed mass transfer. The obtained mass transfer coefficients can be applied in fluidized bed models used for various engineering design, reactor scale-up and process research tasks, and they consequently provide an enhanced prediction accuracy of the performance of fluidized bed processes.

Large-eddy simulation of wind flows over complex terrains for wind energy applications

Wind energy has obtained outstanding expectations due to risks of global warming and nuclear energy production plant accidents. Nowadays, wind farms are often constructed in areas of complex terrain. A potential wind farm location must have the site thoroughly surveyed and the wind climatology analyzed before installing any hardware. Therefore, modeling of Atmospheric Boundary Layer (ABL) flows over complex terrains containing, e.g. hills, forest, and lakes is of great interest in wind energy applications, as it can help in locating and optimizing the wind farms. Numerical modeling of wind flows using Computational Fluid Dynamics (CFD) has become a popular technique during the last few decades. Due to the inherent flow variability and large-scale unsteadiness typical in ABL flows in general and especially over complex terrains, the flow can be difficult to be predicted accurately enough by using the Reynolds-Averaged Navier-Stokes equations (RANS). Large- Eddy Simulation (LES) resolves the largest and thus most important turbulent eddies and models only the small-scale motions which are more universal than the large eddies and thus easier to model. Therefore, LES is expected to be more suitable for this kind of simulations although it is computationally more expensive than the RANS approach. With the fast development of computers and open-source CFD software during the recent years, the application of LES toward atmospheric flow is becoming increasingly common nowadays. The aim of the work is to simulate atmospheric flows over realistic and complex terrains by means of LES. Evaluation of potential in-land wind park locations will be the main application for these simulations. Development of the LES methodology to simulate the atmospheric flows over realistic terrains is reported in the thesis. The work also aims at validating the LES methodology at a real scale. In the thesis, LES are carried out for flow problems ranging from basic channel flows to real atmospheric flows over one of the most recent real-life complex terrain problems, the Bolund hill. All the simulations reported in the thesis are carried out using a new OpenFOAM® -based LES solver. The solver uses the 4th order time-accurate Runge-Kutta scheme and a fractional step method. Moreover, development of the LES methodology includes special attention to two boundary conditions: the upstream (inflow) and wall boundary conditions. The upstream boundary condition is generated by using the so-called recycling technique, in which the instantaneous flow properties are sampled on aplane downstream of the inlet and mapped back to the inlet at each time step. This technique develops the upstream boundary-layer flow together with the inflow turbulence without using any precursor simulation and thus within a single computational domain. The roughness of the terrain surface is modeled by implementing a new wall function into OpenFOAM® during the thesis work. Both, the recycling method and the newly implemented wall function, are validated for the channel flows at relatively high Reynolds number before applying them to the atmospheric flow applications. After validating the LES model over simple flows, the simulations are carried out for atmospheric boundary-layer flows over two types of hills: first, two-dimensional wind-tunnel hill profiles and second, the Bolund hill located in Roskilde Fjord, Denmark. For the twodimensional wind-tunnel hills, the study focuses on the overall flow behavior as a function of the hill slope. Moreover, the simulations are repeated using another wall function suitable for smooth surfaces, which already existed in OpenFOAM® , in order to study the sensitivity of the flow to the surface roughness in ABL flows. The simulated results obtained using the two wall functions are compared against the wind-tunnel measurements. It is shown that LES using the implemented wall function produces overall satisfactory results on the turbulent flow over the two-dimensional hills. The prediction of the flow separation and reattachment-length for the steeper hill is closer to the measurements than the other numerical studies reported in the past for the same hill geometry. The field measurement campaign performed over the Bolund hill provides the most recent field-experiment dataset for the mean flow and the turbulence properties. A number of research groups have simulated the wind flows over the Bolund hill. Due to the challenging features of the hill such as the almost vertical hill slope, it is considered as an ideal experimental test case for validating micro-scale CFD models for wind energy applications. In this work, the simulated results obtained for two wind directions are compared against the field measurements. It is shown that the present LES can reproduce the complex turbulent wind flow structures over a complicated terrain such as the Bolund hill. Especially, the present LES results show the best prediction of the turbulent kinetic energy with an average error of 24.1%, which is a 43% smaller than any other model results reported in the past for the Bolund case. Finally, the validated LES methodology is demonstrated to simulate the wind flow over the existing Muukko wind farm located in South-Eastern Finland. The simulation is carried out only for one wind direction and the results on the instantaneous and time-averaged wind speeds are briefly reported. The demonstration case is followed by discussions on the practical aspects of LES for the wind resource assessment over a realistic inland wind farm.

Kevyen istutuskoneen suunnittelu puuntaimille

Työssä pyritään suunnittelemaan kevyempi versio jo olemassa olevasta puuntaimien istutuslaitteesta. Työ koostuu kahdesta osasta. Ensimmäisessä teoria osuudessa käydään läpi mekatronisen koneen suunnittelussa huomioitavia seikkoja ja järjestelmällistä tuotekehitysprosessia yleisesti. Toisessa osassa esitellään nykyisten istutuslaitteiden kehityshistoriaa ja nykyisin koneellisessa metsänistutuksessa käytössä olevia laitteita. Loppuratkaisujen aikaan saamisessa pyritään QFD-menetelmää käyttämällä saamaan aikaan kevyen istutuskoneen vaatimusprofiili ja profiilissa ilmi tulleiden vaatimusten ja toiveiden pohjalta kehitettiin ratkaisuja joilla perinteistä koneellista istutus toimintaa voidaan uudistaa. Materiaalinvalinnan avulla optimoitiin kevyttä istutuskonetta pyrkimällä löytämään ympäristöystävälliset materiaalit jotka ovat tuotteen elinkaarta kokonaisuutena ajatellen parhaat mahdolliset. Työssä saatiin aikaan malli jolla on mahdollista jatkokehittelyn jälkeen ja kunnolla tuotteistettuna edistää koneellisen metsänistutuksen yleistymistä. Työn aikana huomattiin, että suurimmat esteet metsän istutuksen koneellistumiselle ovat nykyisten koneiden korkeat hankinta- ja käyttökustannukset sekä koneiden käyttämisen vaatima ammattitaito. Kustannuksia alentamalla ja käyttökynnystä madaltamalla voi edistää koneellisen metsänistutuksen yleistymistä tehostamisen rinnalla.

Study of the advancement of innovations in communications industry. Case study: Russian Post Company

This study attempted to provide a project based on the already tested and successful results of foreign business which can help to contain the final price of innovation on desired levels. The research will attempt to dig out most of available information related to aforementioned definitions and thus completing theoretical background. Next author will explain used methodology and the process of evidence collection. After that the study will show the analysis of collected data in order to obtain results which are going to be compared with stated objectives in the final part. The conclusion of the research and proposed possibilities for additional work will be given in the last part. For this study author has chosen the qualitative model because it performs very well for analysis of small scale of data. The case study method was used because it gave author an opportunity to make an in-depth analysis of the collected information about particular organization so it became possible to analyze system's details in comparison. The results have been early considered valid and applicable to other studies. As the result thesis has proposed undertakings which reflect researches aimed on solving problems with provision of services and development of communications. In addition thesis has proposed formulation of database of postal service for Russian Post when (by request) customer possess an account where he or she can access postal services via PC or info table in postal office and order delivery of postal products which will be given private identification code. Project's payoff period has been calculated as well.

Spatial and temporal variation in fish populations and assemblages in coastal waters of the northern Baltic Proper

The distribution and traits of fish are of interest both ecologically and socio-economically. In this thesis, phenotypic and structural variation in fish populations and assemblages was studied on multiple spatial and temporal scales in shallow coastal areas in the archipelago of the northern Baltic Proper. In Lumparn basin in Åland Islands, the fish assemblage displayed significant seasonal variation in depth zone distribution. The results indicate that investigating both spatial and temporal variation in small scale is crucial for understanding patterns in fish distribution and community structure in large scale. The local population of Eurasian perch Perca fluviatilis L displayed habitat-specific morphological and dietary variation. Perch in the pelagic zone were on average deeper in their body shape than the littoral ones and fed on fish and benthic invertebrates. The results differ from previous studies conducted in freshwater habitats, where the pelagic perch typically are streamlined in body shape and zooplanktivorous. Stable isotopes of carbon and nitrogen differed between perch with different stomach contents, suggesting differentiation of individual diet preferences. In the study areas Lumparn and Ivarskärsfjärden in Åland Islands and Galtfjärden in Swedish east coast, the development in fish assemblages during the 2000’s indicated a general shift towards higher abundances of small-bodied lower-order consumers, especially cyprinids. For European pikeperch Sander lucioperca L., recent declines in adult fish abundances and high mortalities (Z = 1.06–1.16) were observed, which suggests unsustainably high fishing pressure on pikeperch. Based on the results it can be hypothesized that fishing has reduced the abundances of large predatory fish, which together with bottom-up forcing by eutrophication has allowed the lower-order consumer species to increase in abundances. This thesis contributes to the scientific understanding of aquatic ecosystems with new descriptions on morphological and dietary adaptations in perch in brackish water, and on the seasonal variation in small-scale spatial fish distribution. The results also demonstrate anthropogenic effects on coastal fish communities and underline the urgency of further reducing nutrient inputs and regulating fisheries in the Baltic Sea region.