Role of Polyelectrolyte for Layer-by-Layer Compact TiO(2) Films in Efficiency Enhanced Dye-Sensitized Solar Cells

Efficient compact TiO(2) films using different polyeleetrolytes are prepared by the layer-by-layer technique (LbL) and applied as an effective contact and blocking film in dye-sensitized solar cells (DSCs). The polyanion thermal stability plays a major role on the compact layers, which decreases back electron transfer processes and current losses at the FTO/TiO(2) interface. FESEM images show that polyelectrolytes such is sodium sullonated polystyrene (PSS) and sulfonated lignin (SE), in comparison to poly(acrylic acid) (FAA), ensure an adequate morphology for the LbL TiO(2) layer deposited before the mesoporous film, even triter the sintering step at 450 degrees C. The so treated photoanode in DSCs leads to a 30% improvement On the overall conversion efficiency. Electrochemical impedance spectroscopy (EIS) is employed to ascertain the role of die compact films with such polyelectrolytes. The significant increase in V(oc) of the solar cells with adequate polyelectrolytes in the LbL TiO(2) films shows their pivotal role in decreasing the electron recombination at the FTO surface and enhancing the electrical contact of FTO with the mesoporous TiO(2) layer.

Electrostatic layer-by-layer and electrophoretic depositions as methods for electrochromic nanoparticle immobilization

The present paper describes the immobilization of nanoparticles onto conducting substrates by using both electrostatic layer-by-layer and electrophoretic deposition (EPD) methods. These two techniques were compared in high-performance electrochromic electrodes based on mixed nickel hydroxide nanoparticles. In addition to easy handling, EPD seems to be the most suitable method for the immobilization of nanoparticles, leading to higher electrochromic efficiencies, lower response times and higher stability upon coloration and bleaching cycling. (C) 2008 Elsevier Ltd. All rights reserved.

Ruthenium oxide hexacyanoferrate modified electrode for hydrogen peroxide detection

A sensor for H2O2 amperometric detection based on a Prussian blue (PB) analogue was developed. The electrocatalytic process allows the determination of hydrogen peroxide at 0.0 V with a limit of detection of 1.3 mu mol L-1 in a flow injection analysis (FIA) configuration. Studies on the optimization of the FIA parameters were performed and under optimal FIA operational conditions the linear response of the method was extended up to 500 mu mol L-1 hydrogen peroxide with good stability. The possibility of using the developed sensor in medium containing sodium ions and the increased operational stability constitute advantages in comparison with PB-based amperometric sensors. The usefulness of the methodology was demonstrated by addition-recovery experiments with rainwater samples and values were in the 98.8 to 103% range.

Electrostatic layer-by-layer deposition and electrochemical characterization of thin films composed of MnO(2) nanoparticles in a room-temperature ionic liquid

Thin films of MnO(2) nanoparticles were grown using the layer-by-layer method with poly (diallyldimetylammonium) as the intercalated layer. The film growth was followed by UV-vis, electrochemical quartz crystal microbalance (EQCM), and atomic force microscopy. Linear growth due to electrostatic immobilization of layers was observed up to 30 bilayers, but electrical connectivity was maintained only for 12 MnO(2)/PPDA bilayers. The electrochemical characterization of this film in 1-butyl-2,3-dimethyl-imidazolium (BMMI) bis(trifluoromethanesulfonyl)imide (TFSI) (BMMITFSI) with and without addition of a lithium salt indicated a higher electrochemical response of the nanostructured electrode in the lithium-containing electrolyte. On the basis of EQCM experiments, it was possible to confirm that the charge compensation process is achieved mainly by the TFSI anion at short times (<2 s) and by BMMI and lithium cations at longer times. The fact that large ions like TFSI and BMMI participate in the electroneutrality is attributed to the redox reaction that occurs at the superficial sites and to the high concentration of these species compared to that of lithium cations.

Ab Initio Analysis of Monomers and Dimers of Trialkylphosphine Oxides: Structural and Thermodynamic Stability

Structural and thermodynamic stabilities of monomers and dimers of trialkylphosphine oxides (TRPO) were Studied using quantum chemistry calculations. Density functional theory calculations were carried Out and the structures Of four TRPO have been determined: TMPO (methyl; R = CH(3)), TEPO (ethyl; R = CH(3)CH(2)), TBPO (n-butyl; R = CH(3)(CH(2))(3)), and TOPO (n-octyl; R = CH(3)(CH(2))(7)). TRPO homodimers were investigated considering two isomeric possibilities for each dimer. Relative binding energies and the enthalpic and entropic contributions to the Gibbs free energy were Calculated for all dimers. The formation of dimers from the individual monomeric TRPO species as a function of temperature was also analyzed. (C) 2008 Wiley Periodicals, Inc. Int J Quantum Chem 109: 250-258, 2009

All solid-state electrochromic devices with gelatin-based electrolyte

6 x 8cm(2) electrochromic devices (ECDs) with the configuration K-glass/EC-layer/electrotype/ion-storage (IS) layer/K-glass, have been assembled using Nb2O5:Mo EC layers, a (CeO2)(0.81)-TiO2 IS-layer and a new gelatin electrolyte containing Li+ ions. The structure of the electrolyte is X-ray amorphous. Its ionic conductivity passed by a maximum of 1.5 x 10(-5) S/CM for a lithium concentration of 0.3g/15ml. The value increases with temperature and follows an Arrhenius law with an activation energy of 49.5 kJ/mol. All solid-state devices show a reversible gray coloration, a long-term stability of more than 25,000 switching cycles (+/- 2.0 V/90 s), a transmission change at 550 nm between 60% (bleached state) and 40% (colored state) corresponding to a change of the optical density (Delta OD = 0. 15) with a coloration efficiency increasing from 10cm(2)/C (initial cycle) to 23cm(2)/C (25,000th cycle). (c) 2007 Elsevier B.V. All rights reserved.

Study of a gold electrode modified by trans-[Ru(NH(3))(4)(Ist)SO(4)](+) to produce an electrochemical sensor for nitric oxide

The modification of a gold electrode surface by electropolymerization of trans-[Ru(NH(3))(4)(Ist)SO(4)](+) to produce an electrochemical sensor for nitric oxide was investigated. The influence of dopamine, serotonin and nitrite as interferents for NO detection was also examined using square-wave voltammetry (SWV). The characterization of the modified electrode was carried out by cyclic voltammetry, electrochemical quartz crystal microbalance (EQCM) and SERS techniques. The gold electrode was successfully modified by the trans-[Ru(NH(3))(4)(Ist)SO(4)](+) complex ion using cyclic voltammetry. The experiments show that a monolayer of the film is achieved after ten voltammetric cycles, that NO in solution can coordinate to the metal present in the layer, that dopamine, serotonin and nitrite are interferents for the detection of NO, and that the response for the nitrite is much less significant than the responses for dopamine and serotonin. The proposed modified electrode has the potential to be applied as a sensor for NO. (C) 2011 Elsevier Ltd. All rights reserved.

Superhydrophobic polyimide films with a hierarchical topography : combined replica molding and layer-by-layer assembly

Artificial superhydrophobic surfaces with a hierarchical topography were fabricated by using layer-by-layer assembly of polyelectrolytes and silica nanoparticles on microsphere-patterned polyimide precursor substrates followed with thermal and fluoroalkylsilane treatment. In this special hierarchical topography, micrometer-scale structures were provided by replica molding of polyamic acid using two-dimensional arrays of polystyrene latex spheres as templates, and nanosized silica particles were then assembled on these microspheres to construct finer structures at the nanoscale. Heat treatment was conducted to induce chemical cross-linking between polyelectrolytes and simultaneously convert polyamic acid to polyimide. After surface modification with fluoroalkylsilane, the as-prepared highly hydrophilic surface was endowed with superhydrophobicity due to the bioinspired combination of low surface energy materials and hierarchical surface structures. A superhydrophobic surface with a static water contact angle of 160 degrees and sliding angle of less than 10 degrees was obtained. Notably, the polyimide microspheres were integrated with the substrate and were mechanically stable. In addition, the chemical and mechanical stability of the polyelectrolyte/silica nanoparticle multilayers could be increased by heat-induced cross-linking between polyelectrolytes to form nylon-like films, as well as the formation of interfacial chemical bonds.

Polymer coatings containing nano particles of zinc oxide for the UV protection of dyed polyester fabrics

The useful life of many outdoor textile products is limited by degradation caused by exposure to sunlight, in particular by the ultra violet component (below 400 nm). The degradation results in fading of colours and also loss of physical properties, such as tear strength and abrasion resistance. Degradation can be decreased with UV absorbers, often used in conjunction with antioxidants or free radical quenchers. The protection afforded by these organic compounds is, however, limited as they are ultimately destroyed by the UV radiation they absorb.
An alternative approach is to coat fabrics with a polymer containing an inorganic UV absorber, such as zinc oxide. The inherent stability of zinc oxide would be expected to provide a protective effect over a much longer period than can be achieved with an organic UV absorber. A possible disadvantage of zinc oxide when applied in a polymer film is that absorption and scattering of visible light can produce hazy films and, hence, an unacceptable change in fabric appearance.
This poster paper examines the possibility of using nano particles of zinc oxide dispersed in acrylic polymers for protecting dyed polyester fabrics against sunlight fading. Factors affecting both UV absorbance and film clarity will be discussed. The possibility will also be examined that the protective effect may be reduced in some circumstances by reactive oxygen species, generated by the interaction of UV with zinc oxide in the presence of air and water.

An embedded two-layer feature selection approach for microarray data analysis

Feature selection is an important technique in dealing with application problems with large number of variables and limited training samples, such as image processing, combinatorial chemistry, and microarray analysis. Commonly employed feature selection strategies can be divided into filter and wrapper. In this study, we propose an embedded two-layer feature selection approach to combining the advantages of filter and wrapper algorithms while avoiding their drawbacks. The hybrid algorithm, called GAEF (Genetic Algorithm with embedded filter), divides the feature selection process into two stages. In the first stage, Genetic Algorithm (GA) is employed to pre-select features while in the second stage a filter selector is used to further identify a small feature subset for accurate sample classification. Three benchmark microarray datasets are used to evaluate the proposed algorithm. The experimental results suggest that this embedded two-layer feature selection strategy is able to improve the stability of the selection results as well as the sample classification accuracy.

Synthesis and characterization of silver nanoparticles and titanium oxide nanofibers : toward multifibrous nanocomposites

A new method was investigated to produce new multiscale fibrous nanocomposites comprised of titanium oxide (TiO₂) nanofibers and silver (Ag) nanoparticles (NPs). The process involved electrospinning TiO₂ precursor solution containing colloidal solution of Ag NPs, and organic solvent (dimethyl-n′n-formamide) to fabricate a porous, nonwoven, free-standing nanofiber mesh. Postprocess heating of the electrospun nanofibers entailed calcination in air environment at 500°C for 3 h. Microemulsion processing was used to generate NPs of Ag in a monodispersed distribution throughout the colloidal solution. X-ray diffraction data were consistent with the anatase phase of TiO2, while transmission electron microscopy and hydrogen desorption measurements revealed a very porous microstructure. It was demonstrated that NP colloidal stability is solvent dependent. It is anticipated that incorporation of metal particles in nanofibers will lead to enhanced photocurrent generation, when used in functional devices.

Stability of aqueous films between bubbles. Part 1. The effect of speed on bubble coalescence in purified water and simple electrolyte solutions

Film thinning experiments have been conducted with aqueous films between two air phases in a thin film pressure balance. The films are free of added surfactant but simple NaCl electrolyte is added in some experiments. Initially the experiments begin with a comparatively large volume of water in a cylindrical capillary tube a few millimeters in diameter, and by withdrawing water from the center of the tube the two bounding menisci are drawn together at a prescribed rate. Thismodels two air bubbles approaching at a controlled speed. In pure water, the results show three regimes of behavior depending on the approach speed; at slow speed (<1 μm/s) it is possible to form a flat film of pure water, ∼100 nm thick, that is stabilized indefinitely by disjoining pressure due to repulsive double-layer interactions between naturally charged air/water interfaces. The data are consistent with a surface potential of -57mV on the bubble surfaces. At intermediate approach speed (∼1-150 μm/s), the films are transiently stable due to hydrodynamic drainage effects, and bubble coalescence is delayed by ∼10-100 s. At approach speeds greater than ∼150 μm/s, the hydrodynamic resistance appears to become negligible, and the bubbles coalesce without any measurable delay. Explanations for these observations are presented that take into account Derjaguin-Landau-Verwey-Overbeek and Marangoni effects entering through disjoining pressure, surface mobility, and hydrodynamic flow regimes in thin film drainage. In particular, it is argued that the dramatic reduction in hydrodynamic resistance is a transition from viscosity-controlled drainage to inertia-controlled drainage associated with a change from immobile to mobile air/water interfaces on increasing the speed of approach of two bubbles. A simple model is developed that accounts for the boundaries between different film stability or coalescence regimes. Predictions of the model are consistent with the data, and the effects of adding electrolyte can be explained. In particular, addition of electrolyte at high concentration inhibits the near-instantaneous coalescence phenomenon, thereby contributing to increased foam film stability at high approach speeds, as reported in previous literature. This work highlights the significance of bubble approach speed as well as electrolyte concentration in affecting bubble coalescence.

Structure and thermal stability of natural rubber reinforced with in situ generated zinc sorbate

In situ prepared zinc disorbate (ZDS) in natural rubber (NR) by the reaction of zinc oxide and sorbic acid was used to reinforce the dicumyl peroxide-cured NR vulcanizate. The changes in mechanical properties of NR vulcanizates after ageing and were determined and the structures and thermal stability of vulcanizates were also analyzed using scanning electron microscope and thermal gravimetric analyzer. The change ratios in tensile strength and elongation at break of NR vulcanizate with theoretic formation of ZDS of 21phr can be increased to -33 from -44 and -27 from -38 after ageing and the initial weight loss temperature of NR vulcanizate can be increased for about 7°C as compared to un-reinforced NR vulcanizate, indicating that the antioxidative behavior and thermal stability of NR can be improved significantly with theoretic formation of ZDS of 21phr.

Electrophoretic deposition of YSZ thin-film electrolyte for SOFCs utilizing electrostatic-steric stabilized suspensions obtained via high energy ball milling

This manuscript describes a facile alternative route to make thin-film yttria-stabilized zirconia (YSZ) electrolyte by liquid-phase assisted electrophoretic deposition utilizing electrostatic-steric stabilized YSZ suspension followed by sintering. Very fine YSZ particles in ball-milled suspension facilitate their sustained dispersion through electrostatic mechanism as evidenced by their higher zeta potentials. Binder addition into the ball-milled suspension is also demonstrated to contribute complementary steric hindrance effects on suspension stability. As the consequence, the film quality and sinterability improve in the sequence of film made from non ball-milled suspension, film made from ball-milled suspension and film made from ball-milled suspension with binder addition. The specific deposition mechanisms pertaining to each suspension are also postulated and discussed below. A very thin dense electrolyte layer of ∼10 μm can be achieved via electrophoretic deposition route utilizing ball-milled suspension and binder addition. This in turn, makes the electrolyte resistance a more negligible part of the overall cell resistance. Further on, we also tested the performance of SOFC utilizing as-formed 10 μm YSZ electrolyte i.e. YSZ-NiO|YSZ|LSM (La0.8Sr0.2MnO3-δ), whereby a maximum power density of ∼850 mW cm−2 at 850 °C was demonstrated.