Design and evaluation of multi-band RF energy harvesting circuits and antennas for WSNs

Radio frequency (RF) energy harvesting is an emerging technology that will enable to drive the next generation of wireless sensor networks (WSNs) without the need of using batteries. In this paper, we present RF energy harvesting circuits specifically developed for GSM bands (900/1800) and a wearable dual-band antenna suitable for possible implementation within clothes for body worn applications. Besides, we address the development and experimental characterization of three different prototypes of a five-stage Dickson voltage multiplier (with match impedance circuit) responsible for harvesting the RF energy. Different printed circuit board (PCB) fabrication techniques to produce the prototypes result in different values of conversion efficiency. Therefore, we conclude that if the PCB fabrication is achieved by means of a rigorous control in the photo-positive method and chemical bath procedure applied to the PCB it allows for attaining better values for the conversion efficiency. All three prototypes (1, 2 and 3) can power supply the IRIS sensor node for RF received powers of -4 dBm, -6 dBm and -5 dBm, and conversion efficiencies of 20, 32 and 26%, respectively. © 2014 IEEE.

Design of a doctorate programme on technology assessment: A sabbatical leave project

The work agenda includes the production of a report on different doctoral programmes on “Technology Assessment” in Europe, the US and Japan, in order to analyse collaborative post-graduation activities. Finally, the proposals on collaborative post-graduation programme between FCTUNL and ITAS-FZK will be organised by an ongoing discussion process with colleagues from ITAS.

On the development of a test-bed application for the ART-WiSe architecture

The ART-WiSe (Architecture for Real-Time communications in Wireless Sensor Networks) framework aims at the design of new communication architectures and mechanisms for time-sensitive Wireless Sensor Networks (WSNs). We adopted a two-tiered architecture where an overlay Wireless Local Area Network (Tier 2) serves as a backbone for a WSN (Tier 1), relying on existing standard communication protocols and commercial-off-the-shell (COTS) technologies – IEEE 802.15.4/ZigBee for Tier 1 and IEEE 802.11 for Tier 2. In this line, a test-bed application is being developed for assessing, validating and demonstrating the ART-WiSe architecture. A pursuit-evasion application was chosen since it fulfils a number of requirements, namely it is feasible and appealing and imposes some stress to the architecture in terms of timeliness. To develop the testbed based on the previously referred technologies, an implementation of the IEEE 8021.5.4/ZigBee protocols is being carried out, since there is no open source available to the community. This paper highlights some relevant aspects of the ART-WiSe architecture, provides some intuition on the protocol stack implementation and presents a general view over the envisaged test-bed application.

Energy and delay trade-off of the GTS allocation mechanism in IEEE 802.15.4 for wireless sensor networks

The IEEE 802.15.4 protocol proposes a flexible communication solution for Low-Rate Wireless Personal Area Networks (LR-WPAN) including wireless sensor networks (WSNs). It presents the advantage to fit different requirements of potential applications by adequately setting its parameters. When in beaconenabled mode, the protocol can provide timeliness guarantees by using its Guaranteed Time Slot (GTS) mechanism. However, power-efficiency and timeliness guarantees are often two antagonistic requirements in wireless sensor networks. The purpose of this paper is to analyze and propose a methodology for setting the relevant parameters of IEEE 802.15.4-compliant WSNs that takes into account a proper trade-off between power-efficiency and delay bound guarantees. First, we propose two accurate models of service curves for a GTS allocation as a function of the IEEE 802.15.4 parameters, using Network Calculus formalism. We then evaluate the delay bound guaranteed by a GTS allocation and express it as a function of the duty cycle. Based on the relation between the delay requirement and the duty cycle, we propose a power-efficient superframe selection method that simultaneously reduces power consumption and enables meeting the delay requirements of real-time flows allocating GTSs. The results of this work may pave the way for a powerefficient management of the GTS mechanism in an IEEE 802.15.4 cluster.

Fractional dynamics in liquid manipulation

This paper presents a fractional calculus perspective in the study of signals captured during the movement of a mechanical manipulator carrying a liquid container. In order to study the signals an experimental setup is implemented. The system acquires data from the sensors, in real time, and, in a second phase, processes them through an analysis package. The analysis package runs off-line and handles the recorded data. The results show that the Fourier spectrum of several signals presents a fractional behavior. The experimental study provides useful information that can assist in the design of a control system and the trajectory planning to be used in reducing or eliminating the effect of vibrations.

Linear and sliding-mode control design for matrix converter-based unified power flow controllers

This paper presents the design and compares the performance of linear, decoupled and direct power controllers (DPC) for three-phase matrix converters operating as unified power flow controllers (UPFC). A simplified steady-state model of the matrix converter-based UPFC fitted with a modified Venturini high-frequency pulse width modulator is first used to design the linear controllers for the transmission line active (P) and reactive (Q) powers. In order to minimize the resulting cross coupling between P and Q power controllers, decoupled linear controllers (DLC) are synthesized using inverse dynamics linearization. DPC are then developed using sliding-mode control techniques, in order to guarantee both robustness and decoupled control. The designed P and Q power controllers are compared using simulations and experimental results. Linear controllers show acceptable steady-state behaviour but still exhibit coupling between P and Q powers in transient operation. DLC are free from cross coupling but are parameter sensitive. Results obtained by DPC show decoupled power control with zero error tracking and faster responses with no overshoot and no steady-state error. All the designed controllers were implemented using the same digital signal processing hardware.

Modeling for control design of a multi-reach water canal

This article addresses the problem of obtaining reduced complexity models of multi-reach water delivery canals that are suitable for robust and linear parameter varying (LPV) control design. In the first stage, by applying a method known from the literature, a finite dimensional rational transfer function of a priori defined order is obtained for each canal reach by linearizing the Saint-Venant equations. Then, by using block diagrams algebra, these different models are combined with linearized gate models in order to obtain the overall canal model. In what concerns the control design objectives, this approach has the advantages of providing a model with prescribed order and to quantify the high frequency uncertainty due to model approximation. A case study with a 3-reach canal is presented, and the resulting model is compared with experimental data. © 2014 IEEE.

A sensor classification strategy for robotic manipulators

In practice the robotic manipulators present some degree of unwanted vibrations. The advent of lightweight arm manipulators, mainly in the aerospace industry, where weight is an important issue, leads to the problem of intense vibrations. On the other hand, robots interacting with the environment often generate impacts that propagate through the mechanical structure and produce also vibrations. In order to analyze these phenomena a robot signal acquisition system was developed. The manipulator motion produces vibrations, either from the structural modes or from endeffector impacts. The instrumentation system acquires signals from several sensors that capture the joint positions, mass accelerations, forces and moments, and electrical currents in the motors. Afterwards, an analysis package, running off-line, reads the data recorded by the acquisition system and extracts the signal characteristics. Due to the multiplicity of sensors, the data obtained can be redundant because the same type of information may be seen by two or more sensors. Because of the price of the sensors, this aspect can be considered in order to reduce the cost of the system. On the other hand, the placement of the sensors is an important issue in order to obtain the suitable signals of the vibration phenomenon. Moreover, the study of these issues can help in the design optimization of the acquisition system. In this line of thought a sensor classification scheme is presented. Several authors have addressed the subject of the sensor classification scheme. White (White, 1987) presents a flexible and comprehensive categorizing scheme that is useful for describing and comparing sensors. The author organizes the sensors according to several aspects: measurands, technological aspects, detection means, conversion phenomena, sensor materials and fields of application. Michahelles and Schiele (Michahelles & Schiele, 2003) systematize the use of sensor technology. They identified several dimensions of sensing that represent the sensing goals for physical interaction. A conceptual framework is introduced that allows categorizing existing sensors and evaluates their utility in various applications. This framework not only guides application designers for choosing meaningful sensor subsets, but also can inspire new systems and leads to the evaluation of existing applications. Today’s technology offers a wide variety of sensors. In order to use all the data from the diversity of sensors a framework of integration is needed. Sensor fusion, fuzzy logic, and neural networks are often mentioned when dealing with problem of combing information from several sensors to get a more general picture of a given situation. The study of data fusion has been receiving considerable attention (Esteban et al., 2005; Luo & Kay, 1990). A survey of the state of the art in sensor fusion for robotics can be found in (Hackett & Shah, 1990). Henderson and Shilcrat (Henderson & Shilcrat, 1984) introduced the concept of logic sensor that defines an abstract specification of the sensors to integrate in a multisensor system. The recent developments of micro electro mechanical sensors (MEMS) with unwired communication capabilities allow a sensor network with interesting capacity. This technology was applied in several applications (Arampatzis & Manesis, 2005), including robotics. Cheekiralla and Engels (Cheekiralla & Engels, 2005) propose a classification of the unwired sensor networks according to its functionalities and properties. This paper presents a development of a sensor classification scheme based on the frequency spectrum of the signals and on a statistical metrics. Bearing these ideas in mind, this paper is organized as follows. Section 2 describes briefly the robotic system enhanced with the instrumentation setup. Section 3 presents the experimental results. Finally, section 4 draws the main conclusions and points out future work.

Design of a laminated composite multi-cel structure subjected to torsion

Laminate composite multi-cell structures have to support both axial and shear stresses when sustaining variable twist. Thus the properties and design of the laminate may not be the most adequate at all cross-sections to support the torsion imposed on the cells. In this work, the effect of some material and geometric parameters on the optimal mechanical behaviour of a multi-cell composite laminate structure is studied when torsion is present. A particle swarm optimization technique is used to maximize the multi-cell structure torsion constant that can be used to obtain the angle of twist of the composite laminate profile.

Design, synthesis and biologival evaluation of novel isoniazid derivatives with potente antitubercular activity

The disturbing emergence of multidrug-resistant strains of Mycobacterium tuberculosis (Mtb) has been driving the scientific community to urgently search for new and efficient antitubercular drugs. Despite the various drugs currently under evaluation, isoniazid is still the key and most effective component in all multi-therapeutic regimens recommended by the WHO. This paper describes the QSAR-oriented design, synthesis and in vitro antitubercular activity of several potent isoniazid derivatives (isonicotinoyl hydrazones and isonicotinoyl hydrazides) against H37Rv and two resistant Mtb strains. QSAR studies entailed RFs and ASNNs classification models, as well as MLR models. Strict validation procedures were used to guarantee the models' robustness and predictive ability. Lipophilicity was shown not to be relevant to explain the activity of these derivatives, whereas shorter N-N distances and lengthy substituents lead to more active compounds. Compounds I, 2, 4, 5 and 6, showed measured activities against H37Rv higher than INH (i.e., MIC <= 0.28 mu M), while compound 9 exhibited a six fold decrease in MIC against the katG (S315T) mutated strain, by comparison with INH (Le., 6.9 vs. 43.8 mu M). All compounds were ineffective against H37Rv(INH) (Delta katG), a strain with a full deletion of the katG gene, thus corroborating the importance of KatG in the activation of INH-based compounds. The most potent compounds were also shown not to be cytotoxic up to a concentration 500 times higher than MIC. (C) 2014 Elsevier Masson SAS. All rights reserved.

Application of genetic algorithms in the design of an electrical potential of fractional order

Fractional calculus (FC) is currently being applied in many areas of science and technology. In fact, this mathematical concept helps the researches to have a deeper insight about several phenomena that integer order models overlook. Genetic algorithms (GA) are an important tool to solve optimization problems that occur in engineering. This methodology applies the concepts that describe biological evolution to obtain optimal solution in many different applications. In this line of thought, in this work we use the FC and the GA concepts to implement the electrical fractional order potential. The performance of the GA scheme, and the convergence of the resulting approximation, are analyzed. The results are analyzed for different number of charges and several fractional orders.

Phex: a computational tool for plate heat exchanges design problems

This paper presents a computational tool (PHEx) developed in Excel VBA for solving sizing and rating design problems involving Chevron type plate heat exchangers (PHE) with 1-pass-1-pass configuration. The rating methodology procedure used in the program is outlined, and a case study is presented with the purpose to show how the program can be used to develop sensitivity analysis to several dimensional parameters of PHE and to observe their effect on transferred heat and pressure drop.

Política(s) de saúde no trabalho : um inquérito sociológico às empresas portuguesas

Resumo Política(s) de saúde no trabalho: um inquérito sociológico às empresas portuguesas A literatura portuguesa sobre políticas, programas e actividades de Segurança, Higiene e Saúde no Trabalho (abreviadamente, SH&ST) é ainda escassa. Com este projecto de investigação pretende-se (i) colmatar essa lacuna, (ii) melhorar o conhecimento dos sistemas de gestão da saúde e segurança no trabalho e (iii) contribuir para a protecção e a promoção da saúde dos trabalhadores. Foi construída uma tipologia com cinco grupos principais de políticas, programas e actividades: A (Higiene & Segurança no Trabalho / Melhoria do ambiente físico de trabalho); B (Avaliação de saúde / Vigilância médica / Prestação de cuidados de saúde); C (Prevenção de comportamentos de risco/ Promoção de estilos de vida saudáveis); D (Intervenções a nível organizacional / Melhoria do ambiente psicossocial de trabalho); E (Actividades e programas sociais e de bem-estar). Havia uma lista de mais de 60 actividades possíveis, correspondendo a um índice de realização de 100%. Foi concebido e desenhado, para ser auto-administrado, um questionário sobre Política de Saúde no Local de Trabalho. Foram efectuados dois mailings, e um follow-up telefónico. O trabalho de campo decorreu entre a primavera de 1997 e o verão de 1998. A amostra (n=259) é considerada representativa das duas mil maiores empresas do país. Uma em cada quatro é uma multinacional. A taxa de sindicalização rondava os 30% da população trabalhadora, mas apenas 16% dos respondentes assinalou a existência de representantes dos trabalhadores eleitos para a SH&ST. A hipótese de investigação principal era a de que as empresas com um sistema integrado de gestão da SH&ST seriam também as empresas com um (i) maior número de políticas, programas e actividades de saúde; (ii) maior índice de saúde; (iii) maior índice de realização; e (iv) maior percentagem dos encargos com a SH&ST no total da massa salarial. As actividades de tipo A e B, tradicionalmente associadas à SH&ST, representavam, só por si, mais de 57% do total. Os resultados, correspondentes às respostas da Secção C do questionário, apontam, para (i) a hipervalorização dos exames de medicina do trabalho; e por outro para (ii) o subaproveitamento de um vasto conjunto de actividades (nomeadamente as de tipo D e E), que são correntemente levadas a cabo pelas empresas e que nunca ou raramente são pensadas em termos de protecção e promoção da saúde dos trabalhadores. As actividades e os programas de tipo C (Prevenção de comportamentos de risco/Promoção de estilos de vida saudáveis), ainda eram as menos frequentes entre nós, a seguir aos Programas sociais e de bem-estar (E). É a existência de sistemas de gestão integrados de SH&ST, e não o tamanho da empresa ou outra característica sociodemográfica ou técnico-organizacional, que permite predizer a frequência de políticas de saúde mais activas e mais inovadores. Os três principais motivos ou razões que levam as empresas portuguesas a investir na protecção e promoção da saúde dos seus trabalhadores eram, por ordem de frequência, (i) o absentismo em geral; (ii) a produtividade, qualidade e/ou competitividade, e (iii) a filosofia de gestão ou cultura organizacional. Quanto aos três principais benefícios que são reportados, surge em primeiro lugar (i) a melhoria da saúde dos trabalhadores, seguida da (ii) melhoria do ambiente do ambiente de trabalho e, por fim, (iii) a melhoria da produtividade, qualidade e/ou competitividade.Quanto aos três principais obstáculos que se põem, em geral, ao desenvolvimento das iniciativas de saúde, eles seriam os seguintes, na percepção dos respondentes: (i) a falta de empenho dos trabalhadores; (ii) a falta de tempo; e (iii) os problemas de articulação/ comunicação a nível interno. Por fim, (i) o empenho das estruturas hierárquicas; (ii) a cultura organizacional propícia; e (iii) o sentido de responsabilidade social surgem, destacadamente, como os três principais factores facilitadores do desenvolvimento da política de saúde no trabalho. Tantos estes factores como os obstáculos são de natureza endógena, susceptíveis portanto de controlo por parte dos gestores. Na sua generalidade, os resultados deste trabalho põem em evidência a fraqueza teóricometodológica de grande parte das iniciativas de saúde, realizadas na década de 1990. Muitas delas seriam medidas avulsas, que se inserem na gestão corrente das nossas empresas, e que dificilmente poderão ser tomadas como expressão de uma política de saúde no local de trabalho, (i) definida e assumida pela gestão de topo, (ii) socialmente concertada, (iii) coerente, (iv) baseada na avaliação de necessidades e expectativas de saúde dos trabalhadores, (v) divulgada, conhecida e partilhada por todos, (vi) contingencial, flexível e integrada, e, por fim, (vii) orientada por custos e resultados. Segundo a Declaração do Luxemburgo (1997), a promoção da saúde engloba o esforço conjunto dos empregadores, dos trabalhadores, do Estado e da sociedade civil para melhorar a segurança, a saúde e o bem-estar no trabalho, objectivo isso que pode ser conseguido através da (i) melhoria da organização e das demais condições de trabalho, da (ii) participação efectiva e concreta dos trabalhadores bem como do seu (iii) desenvolvimento pessoal. Abstract Health at work policies: a sociological inquiry into Portuguese corporations Portuguese literature on workplace health policies, programs and activities is still scarce. With this research project the author intends (i) to improve knowledge on the Occupational Health and Safety (shortly thereafter, OSH) management systems and (ii) contribute to the development of health promotion initiatives at a corporate level. Five categories of workplace health initiatives have been identified: (i) Occupational Hygiene and Safety / Improvement of Physical Working Environment (type A programs); (ii) Health Screening, Medical Surveillance and Other Occupational Health Care Provision (type B programs); (iii) Preventing Risk Behaviours / Promoting Healthy Life Styles (type C programs); (iv) Organisational Change / Improvement of Psycho-Social Working Environment (type D programs); and (v) Industrial and Social Welfare (type E programs). A mail questionnaire was sent to the Chief Executive Officer of the 1500 largest Portuguese companies, operating in the primary and secondary sectors (≥ 100 employees) or tertiary sector (≥ 75 employees). Response rate has reached about 20% (259 respondents, representing about 300 companies). Carried out between Spring 1997 and Summer 1998, the fieldwork has encompassed two direct mailings and one phone follow-up. Sample is considered to be representative of the two thousand largest companies. One in four is a multinational. Union membership rate is about 30%, but only 16% has reported the existence of a workers’ health and safety representative. The most frequent workplace health initiatives were those under the traditional scope of the OSH field (type A and B programs) (57% of total) (e.g., Periodical Medical Examinations; Individual Protective Equipment; Assessment of Working Ability). In SMEs (< 250) it was less likely to find out some time-consuming and expensive activities (e.g., Training on OSH knowledge and skills, Improvement of environmental parameters as ventilation, lighting, heating).There were significant differences in SMEs, when compared with the larger ones (≥ 250) concerning type B programs such as Periodical medical examinations, GP consultation, Nursing care, Other medical and non-medical specialities (e.g., psychiatrist, psychologist, ergonomist, physiotherapist, occupational social worker). With regard to type C programs, there were a greater percentage of programs centred on Substance abuse (tobacco, alcohol, and drug) than on Other health risk behaviours. SMEs representatives reported very few prevention- oriented programs in the field of Drug abuse, Nutrition, Physical activity, Off- job accidents, Blood pressure or Weight control. Frequency of type D programs included Training on Human Resources Management, Training on Organisational Behaviour, Total Quality Management, Job Design/Ergonomics, and Workplace rehabilitation. In general, implementation of this type of programs (Organisational Change / Improvement of Psychosocial Working Environment) is not largely driven by health considerations. Concerning Industrial and Social Welfare (Type E programs), the larger employers are in a better position than SMEs to offer to their employees a large spectrum of health resources and facilities (e.g., Restaurant, Canteen, Resting room, Transport, Infra-structures for physical activity, Surgery, Complementary social protection, Support to recreational and cultural activities, Magazine or newsletter, Intranet). Other workplace health promotion programs like Training on Stress Management, Employee Assistance Programs, or Self-help groups are uncommon in the Portuguese worksites. The existence of integrated OSH management systems, not the company size, is the main variable explaining the implementation of more active and innovative workplace health policies in Portugal. The three main prompting factors reported by employers for health protection and promotion initiatives are: (i) Employee absenteeism; (ii) Productivity, quality and/or competitiveness; and (iii) Corporate culture/management philosophy. On the other hand, (i) Improved staff’s health, (ii) Improved working environment and (iii) Improved productivity, quality and/or competitiveness were the three main benefits reported by companies’ representatives, as a result of successful implementation of workplace health initiatives. (i) Lack of staff commitment; (ii) Lack of time; and (iii) Problems of co-operation and communication within company or establishment (iii) are perceived to be the main barriers companies must cope with. Asked about the main facilitating factors, these companies have pointed out the following ones: (i) Top management commitment; (ii) Corporate culture; and (iii) Sense of social responsibility. This sociological research report shows the methodological weaknesses of workplace health initiatives, carried out by Portuguese companies during the last ‘90s. In many cases, these programs and actions were not part of a corporate health strategy and policy, (i) based on the assessment of workers’ health needs and expectancies, (ii) advocated by the employer or the chief executive officer, (ii) planned and implemented with the staff consultation and participation or (iv) evaluated according to a cost-benefit analysis. In short, corporate health policy and action were still rather based on more traditional OSH approaches and should be reoriented towards Workplace Health Promotion (WHP) approach. According to the Luxembourg Declaration of Workplace Health Promotion in the European Union (1997), WHP is “a combination of: (i) improving the work organisation and environment; (ii) promoting active participation; (iii) encouraging personal development”.Résumée Politique(s) de santé au travail: une enquête sociologique aux entreprises portugaises Au Portugal on ne sait presque rien des politiques de santé au travail, adoptés par les entreprises. Avec ce projet de recherche, on veut (i) améliorer la connaissance sur les systèmes de gestion de la santé et de la sécurité au travail et, au même temps, (ii) contribuer au développement de la promotion de la santé des travailleurs. Une typologie a été usée pour identifier les politiques, programmes et actions de santé au travail: A. Amélioration des conditions de travail / Sécurité au travail; B. Médecine du travail /Santé au travail; C. Prévention des comportements de risque / Promotion de styles de vie sains; D. Interventions organisationnelles / Amélioration des facteurs psychosociaux au travail; E. Gestion de personnel et bien-être social. Un questionnaire postal a été envoyé au représentant maximum des grandes entreprises portugaises, industrielles (≥ 100 employés) ou des services (≥ 75 employés). Le taux de réponse a été environ 20% (259 répondants, concernant trois centaines d’entreprises et d’établissements). La recherche de champ, conduite du printemps 1997 à l’été 1998, a compris deux enquêtes postales et un follow-up téléphonique. L´échantillon est représentatif de la population des deux miles plus grandes entreprises. Un quart sont des multinationales. Le taux de syndicalisation est d’environ 30%. Toutefois, il y a seulement 16% de lieux de travail avec des représentants du personnel pour la santé et sécurité au travail. Les initiatives de santé au travail les plus communes sont celles concernant le domaine plus traditionnel (types A et B) (57% du total): par exemple, les examens de médecine du travail, l’équipement de protection individuelle, les tests d’aptitude au travail. En ce qui concerne les programmes de type C, les plus fréquents sont le contrôle et la prévention des addictions (tabac, alcool, drogue). Les interventions dans le domaine de du système technique et organisationnelle du travail peuvent comprendre les courses de formation en gestion de ressources humaines ou en psychosociologie des organisations, l’ergonomie, le travail posté ou la gestion de la qualité totale. En général, la protection et la promotion de la santé des travailleurs ne sont pas prises en considération dans l’implémentation des initiatives de type D. Il y a des différences quand on compare les grandes entreprises et les moyennes en matière de politique de gestion du personnel e du bien-être (programmes de type E, y compris l’allocation de ressources humaines ou logistiques comme, par exemple, restaurant, journal d’entreprise, transports, installations et équipements sportifs). D’autres activités de promotion de la santé au travail comme la formation en gestion du stress, les programmes d’ assistance aux employés, ou les groupes de soutien et d’auto-aide sont encore très peu fréquents dans les entreprises portugaises. C’est le système intégré de gestion de la santé et de la sécurité au travail, et non pas la taille de l’entreprise, qui aide à prédire l’existence de politiques actives et innovatrices dans ce domaine. Les trois facteurs principaux qui encouragent les actions de santé (prompting factors, en anglais) sont (i) l’absentéisme (y compris la maladie), (ii) les problèmes liés à la productivité, qualité et/ou la compétitivité, et aussi (iii) la culture de l’entreprise/philosophie de gestion. Du coté des bénéfices, on a obtenu surtout l’amélioration (i) de la santé du personnel, (ii) des conditions de travail, et (iii) de la productivité, qualité et/ou compétitivité.Les facteurs qui facilitent les actions de santé au travail sont (i) l’engagement de la direction, (ii) la culture de l’entreprise, et (iii) le sens de responsabilité sociale. Par contre, les obstacles à surmonter, selon les organisations qui ont répondu au questionnaire, seraient surtout (i) le manque d’engagement des travailleurs et de leur représentants, (ii) le temps insuffisant, et (iii) les problèmes de articulation/communication au niveau interne de l’entreprise/établissement. Ce travail de recherche sociologique montre la faiblesse méthodologique des services et activités de santé et sécurité au travail, mis en place par les entreprises portugaises dans les années de 1990, à la suite des accords de concertation sociale de 1991. Dans beaucoup de cas, (i) ces politiques de santé ne font pas partie encore d’un système intégré de gestion, (ii) il n’a pas d’évaluation des besoins et des expectatives des travailleurs, (iii) c’est très bas ou inexistant le niveau de participation du personnel, (iv) on ne fait pas d’analyse coût-bénéfice. On peut conclure que les politiques de santé au travail sont plus proches de la médecine du travail et de la sécurité au travail que de la promotion de la santé des travailleurs. Selon la Déclaration du Luxembourg sur la Promotion de la Santé au Lieu de Travail dans la Communauté Européenne (1997), celle-ci « comprend toutes les mesures des employeurs, des employés et de la société pour améliorer l'état de santé et le bien être des travailleurs » e « ceci peut être obtenu par la concentration des efforts dans les domaines suivants: (i) amélioration de l'organisation du travail et des conditions de travail ; (ii) promotion d'une participation active des collaborateurs ; (iii) renforcement des compétences personnelles ».

Design and optimization of na ultra wideband and compact microwave antenna for radiometric monitoring of brain temperature

We present the modeling efforts on antenna design and frequency selection to monitor brain temperature during prolonged surgery using noninvasive microwave radiometry. A tapered log-spiral antenna design is chosen for its wideband characteristics that allow higher power collection from deep brain. Parametric analysis with the software HFSS is used to optimize antenna performance for deep brain temperature sensing. Radiometric antenna efficiency (eta) is evaluated in terms of the ratio of power collected from brain to total power received by the antenna. Anatomical information extracted from several adult computed tomography scans is used to establish design parameters for constructing an accurate layered 3-D tissue phantom. This head phantom includes separate brain and scalp regions, with tissue equivalent liquids circulating at independent temperatures on either side of an intact skull. The optimized frequency band is 1.1-1.6 GHz producing an average antenna efficiency of 50.3% from a two turn log-spiral antenna. The entire sensor package is contained in a lightweight and low-profile 2.8 cm diameter by 1.5 cm high assembly that can be held in place over the skin with an electromagnetic interference shielding adhesive patch. The calculated radiometric equivalent brain temperature tracks within 0.4 degrees C of the measured brain phantom temperature when the brain phantom is lowered 10. C and then returned to the original temperature (37 degrees C) over a 4.6-h experiment. The numerical and experimental results demonstrate that the optimized 2.5-cm log-spiral antenna is well suited for the noninvasive radiometric sensing of deep brain temperature.

Design optimization of cruciform specimens for biaxial fatigue loading

In order to correctly assess the biaxial fatigue material properties one must experimentally test different load conditions and stress levels. With the rise of new in-plane biaxial fatigue testing machines, using smaller and more efficient electrical motors, instead of the conventional hydraulic machines, it is necessary to reduce the specimen size and to ensure that the specimen geometry is appropriated for the load capacity installed. At the present time there are no standard specimen’s geometries and the indications on literature how to design an efficient test specimen are insufficient. The main goal of this paper is to present the methodology on how to obtain an optimal cruciform specimen geometry, with thickness reduction in the gauge area, appropriated for fatigue crack initiation, as a function of the base material sheet thickness used to build the specimen. The geometry is optimized for maximum stress using several parameters, ensuring that in the gauge area the stress is uniform and maximum with two limit phase shift loading conditions. Therefore the fatigue damage will always initiate on the center of the specimen, avoiding failure outside this region. Using the Renard Series of preferred numbers for the base material sheet thickness as a reference, the reaming geometry parameters are optimized using a derivative-free methodology, called direct multi search (DMS) method. The final optimal geometry as a function of the base material sheet thickness is proposed, as a guide line for cruciform specimens design, and as a possible contribution for a future standard on in-plane biaxial fatigue tests. © 2014, Gruppo Italiano Frattura. All rights reserved.