Neutron features at the UPM neutronics hall

The neutronics hall of the Nuclear Engineering Department at the Polytechnical University of Madrid has been characterized. The neutron spectra and the ambient dose equivalent produced by an 241AmBe source were measured at various source-to-detector distances on the new bench. Using Monte Carlo methods a detailed model of the neutronics hall was designed, and neutron spectra and the ambient dose equivalent were calculated at the same locations where measurements were carried out. A good agreement between measured and calculated values was found.

Characterization of an 241AmBe neutron irradiation facility by different spectrometric techniques

An automated panoramic irradiator with a 3 Ci 241Am-Be neutron source is installed in a bunker-type large room at the Universidad Politécnica de Madrid (UPM). It was recently modified and a neutron spectrometry campaign was organized to characterize the neutron fields in different measurement points along the irradiation bench. Four research groups working with different Bonner Sphere Spectrometers (BSS) and using different spectral unfolding codes took part to this exercise. INFN-LNF used a BSS formed by 9 spheres plus bare detector, with cylindrical, almost point like, 6LiI(Eu) scintillator (4 mm x 4 mm, from Ludlum); UAZ-UPM employed a similar system but with only 6 spheres plus bare detector; UAB worked with a 3He filled proportional counter at 8kPa filling pressure, cylindrical 9 mm x 10 mm (05NH1 from Eurisys) with 11 spheres configuration; and CIEMAT used 12 spheres with an spherical 3He SP9 counter (Centronic Ltd., UK) with very high sensitivity due to the large diameter (3.2 cm) and the filling pressure of the order of 228 kPa. Each group applied a different spectral unfolding method: INFN and UAB worked with FRUIT ver. 3.0 with their own response matrixes; UAZ-UPM used the BUNKIUT unfolding code with the response matrix UTA4 and CIEMAT employed the GRAVEL-MAXED-IQU package with their own response matrix. The paper shows the main results obtained in terms of neutron spectra at fixed distances from the source as well as total neutron fluence rate and ambient dose equivalent rate H*(10) determined from the spectra. The latter are compared with the readings of a common active survey-meter (LB 6411). The small differences in the results of the various groups are discussed.

Residual strain scanning of alumina-based ceramic composites by neutron diffraction

The objective of this work is to non-destructively determine the residual stress profile in the bulk of two characteristic types of alumina-based composites, with the aim of improving their durability and structural integrity.

Laser Driven Neutron Sources: Characteristics, Applications and Prospects

The basics of laser driven neutron sources, properties and possible applications are discussed. We describe the laser driven nuclear processes which trigger neutron generation, namely, nuclear reactions induced by laser driven ion beam (ion n), thermonuclear fusion by implosion and photo-induced nuclear (gamma n) reactions. Based on their main properties, i.e. point source (<100 μm) and short durations (< ns), different applications are described, such as radiography, time-resolved spectroscopy and pump-probe experiments. Prospects on the development of laser technology suggest that, as higher intensities and higher repetition rate lasers become available (for example, using DPSSL technology), laser driven methodologies may provide neutron fluxes comparable to that achieved by accelerator driven neutron sources in the near future.

Modelización de los Procesos de Cristalización en Poliolefinas

“Por lo tanto, la cristalización de polímeros se supone, y en las teorías se describe a menudo, como un proceso de múltiples pasos con muchos aspectos físico-químicos y estructurales influyendo en él. Debido a la propia estructura de la cadena, es fácil entender que un proceso que es termodinámicamente forzado a aumentar su ordenamiento local, se vea obstaculizado geométricamente y, por tanto, no puede conducirse a un estado de equilibrio final. Como resultado, se forman habitualmente estructuras de no equilibrio con diferentes características dependiendo de la temperatura, presión, cizallamiento y otros parámetros físico-químicos del sistema”. Estas palabras, pronunciadas recientemente por el profesor Bernhard Wunderlich, uno de los mas relevantes fisico-quimicos que han abordado en las ultimas décadas el estudio del estado físico de las macromoléculas, adelantan lo que de alguna manera se explicita en esta memoria y constituyen el “leitmotiv” de este trabajo de tesis. El mecanismo de la cristalización de polímeros esta aun bajo debate en la comunidad de la física de polímeros y la mayoría de los abordajes experimentales se explican a través de la teoría LH. Esta teoría clásica debida a Lauritzen y Hoffman (LH), y que es una generalización de la teoría de cristalización de una molécula pequeña desde la fase de vapor, describe satisfactoriamente muchas observaciones experimentales aunque esta lejos de explicar el complejo fenómeno de la cristalización de polímeros. De hecho, la formulación original de esta teoría en el National Bureau of Standards, a comienzos de la década de los 70, sufrió varias reformulaciones importantes a lo largo de la década de los 80, buscando su adaptación a los hallazgos experimentales. Así nació el régimen III de cristalización que posibilita la creacion de nichos moleculares en la superficie y que dio pie al paradigma ofrecido por Sadler y col., para justificar los experimentos que se obtenian por “scattering” de neutrones y otras técnicas como la técnica de “droplets” o enfriamiento rapido. Por encima de todo, el gran éxito de la teoría radica en que explica la dependencia inversa entre el tamaño del plegado molecular y el subenfriamiento, definido este ultimo como el intervalo de temperatura que media entre la temperatura de equilibrio y la temperatura de cristalización. El problema concreto que aborda esta tesis es el estudio de los procesos de ordenamiento de poliolefinas con distinto grado de ramificacion mediante simulaciones numéricas. Los copolimeros estudiados en esta tesis se consideran materiales modelo de gran homogeneidad molecular desde el punto de vista de la distribución de tamaños y de ramificaciones en la cadena polimérica. Se eligieron estas poliolefinas debido al gran interes experimental en conocer el cambio en las propiedades fisicas de los materiales dependiendo del tipo y cantidad de comonomero utilizado. Además, son modelos sobre los que existen una ingente cantidad de información experimental, que es algo que preocupa siempre al crear una realidad virtual como es la simulación. La experiencia en el grupo Biophym es que los resultados de simulación deben de tener siempre un correlato mas o menos próximo experimental y ese argumento se maneja a lo largo de esta memoria. Empíricamente, se conoce muy bien que las propiedades físicas de las poliolefinas, en suma dependen del tipo y de la cantidad de ramificaciones que presenta el material polimérico. Sin embargo, tal como se ha explicado no existen modelos teóricos adecuados que expliquen los mecanismos subyacentes de los efectos de las ramas. La memoria de este trabajo es amplia por la complejidad del tema. Se inicia con una extensa introducción sobre los conceptos básicos de una macromolecula que son relevantes para entender el contenido del resto de la memoria. Se definen los conceptos de macromolecula flexible, distribuciones y momentos, y su comportamiento en disolución y fundido con los correspondientes parametros caracteristicos. Se pone especial énfasis en el concepto de “entanglement” o enmaranamiento por considerarse clave a la hora de tratar macromoléculas con una longitud superior a la longitud critica de enmaranamiento. Finaliza esta introducción con una reseña sobre el estado del arte en la simulación de los procesos de cristalización. En un segundo capitulo del trabajo se expone detalladamente la metodología usada en cada grupo de casos. En el primer capitulo de resultados, se discuten los estudios de simulación en disolución diluida para sistemas lineales y ramificados de cadena única. Este caso mas simple depende claramente del potencial de torsión elegido tal como se discute a lo largo del texto. La formación de los núcleos “babys” propuestos por Muthukumar parece que son consecuencia del potencial de torsión, ya que este facilita los estados de torsión mas estables. Así que se propone el análisis de otros potenciales que son igualmente utilizados y los resultados obtenidos sobre la cristalización, discutidos en consecuencia. Seguidamente, en un segundo capitulo de resultados se estudian moleculas de alcanos de cadena larga lineales y ramificados en un fundido por simulaciones atomisticas como un modelo de polietileno. Los resultados atomisticos pese a ser de gran detalle no logran captar en su totalidad los efectos experimentales que se observan en los fundidos subenfriados en su etapa previa al estado ordenado. Por esta razon se discuten en los capítulos 3 y 4 de resultados sistemas de cadenas cortas y largas utilizando dos modelos de grano grueso (CG-PVA y CG-PE). El modelo CG-PE se desarrollo durante la tesis. El uso de modelos de grano grueso garantiza una mayor eficiencia computacional con respecto a los modelos atomísticos y son suficientes para mostrar los fenómenos a la escala relevante para la cristalización. En todos estos estudios mencionados se sigue la evolución de los procesos de ordenamiento y de fusión en simulaciones de relajación isoterma y no isoterma. Como resultado de los modelos de simulación, se han evaluado distintas propiedades fisicas como la longitud de segmento ordenado, la cristalinidad, temperaturas de fusion/cristalizacion, etc., lo que permite una comparación con los resultados experimentales. Se demuestra claramente que los sistemas ramificados retrasan y dificultan el orden de la cadena polimérica y por tanto, las regiones cristalinas ordenadas decrecen al crecer las ramas. Como una conclusión general parece mostrarse una tendencia a la formación de estructuras localmente ordenadas que crecen como bloques para completar el espacio de cristalización que puede alcanzarse a una temperatura y a una escala de tiempo determinada. Finalmente hay que señalar que los efectos observados, estan en concordancia con otros resultados tanto teoricos/simulacion como experimentales discutidos a lo largo de esta memoria. Su resumen se muestra en un capitulo de conclusiones y líneas futuras de investigación que se abren como consecuencia de esta memoria. Hay que mencionar que el ritmo de investigación se ha acentuado notablemente en el ultimo ano de trabajo, en parte debido a las ventajas notables obtenidas por el uso de la metodología de grano grueso que pese a ser muy importante para esta memoria no repercute fácilmente en trabajos publicables. Todo ello justifica que gran parte de los resultados esten en fase de publicación. Abstract “Polymer crystallization is therefore assumed, and in theories often described, to be a multi step process with many influencing aspects. Because of the chain structure, it is easy to understand that a process which is thermodynamically forced to increase local ordering but is geometrically hindered cannot proceed into a final equilibrium state. As a result, nonequilibrium structures with different characteristics are usually formed, which depend on temperature, pressure, shearing and other parameters”. These words, recently written by Professor Bernhard Wunderlich, one of the most prominent researchers in polymer physics, put somehow in value the "leitmotiv "of this thesis. The crystallization mechanism of polymers is still under debate in the physics community and most of the experimental findings are still explained by invoking the LH theory. This classical theory, which was initially formulated by Lauritzen and Hoffman (LH), is indeed a generalization of the crystallization theory for small molecules from the vapor phase. Even though it describes satisfactorily many experimental observations, it is far from explaining the complex phenomenon of polymer crystallization. This theory was firstly devised in the early 70s at the National Bureau of Standards. It was successively reformulated along the 80s to fit the experimental findings. Thus, the crystallization regime III was introduced into the theory in order to explain the results found in neutron scattering, droplet or quenching experiments. This concept defines the roughness of the crystallization surface leading to the paradigm proposed by Sadler et al. The great success of this theory is the ability to explain the inverse dependence of the molecular folding size on the supercooling, the latter defined as the temperature interval between the equilibrium temperature and the crystallization temperature. The main scope of this thesis is the study of ordering processes in polyolefins with different degree of branching by using computer simulations. The copolymers studied along this work are considered materials of high molecular homogeneity, from the point of view of both size and branching distributions of the polymer chain. These polyolefins were selected due to the great interest to understand their structure– property relationships. It is important to note that there is a vast amount of experimental data concerning these materials, which is essential to create a virtual reality as is the simulation. The Biophym research group has a wide experience in the correlation between simulation data and experimental results, being this idea highly alive along this work. Empirically, it is well-known that the physical properties of the polyolefins depend on the type and amount of branches presented in the polymeric material. However, there are not suitable models to explain the underlying mechanisms associated to branching. This report is extensive due to the complexity of the topic under study. It begins with a general introduction to the basics concepts of macromolecular physics. This chapter is relevant to understand the content of the present document. Some concepts are defined along this section, among others the flexibility of macromolecules, size distributions and moments, and the behavior in solution and melt along with their corresponding characteristic parameters. Special emphasis is placed on the concept of "entanglement" which is a key item when dealing with macromolecules having a molecular size greater than the critical entanglement length. The introduction finishes with a review of the state of art on the simulation of crystallization processes. The second chapter of the thesis describes, in detail, the computational methodology used in each study. In the first results section, we discuss the simulation studies in dilute solution for linear and short chain branched single chain models. The simplest case is clearly dependent on the selected torsion potential as it is discussed throughout the text. For example, the formation of baby nuclei proposed by Mutukhumar seems to result from the effects of the torsion potential. Thus, we propose the analysis of other torsion potentials that are also used by other research groups. The results obtained on crystallization processes are accordingly discussed. Then, in a second results section, we study linear and branched long-chain alkane molecules in a melt by atomistic simulations as a polyethylene-like model. In spite of the great detail given by atomistic simulations, they are not able to fully capture the experimental facts observed in supercooled melts, in particular the pre-ordered states. For this reason, we discuss short and long chains systems using two coarse-grained models (CG-PVA and CG-PE) in section 3 and 4 of chapter 2. The CG-PE model was developed during the thesis. The use of coarse-grained models ensures greater computational efficiency with respect to atomistic models and is enough to show the relevant scale phenomena for crystallization. In all the analysis we follow the evolution of the ordering and melting processes by both isothermal and non isothermal simulations. During this thesis we have obtained different physical properties such as stem length, crystallinity, melting/crystallization temperatures, and so on. We show that branches in the chains cause a delay in the crystallization and hinder the ordering of the polymer chain. Therefore, crystalline regions decrease in size as branching increases. As a general conclusion, it seems that there is a tendency in the macromolecular systems to form ordered structures, which can grown locally as blocks, occupying the crystallization space at a given temperature and time scale. Finally it should be noted that the observed effects are consistent with both, other theoretical/simulation and experimental results. The summary is provided in the conclusions chapter along with future research lines that open as result of this report. It should be mentioned that the research work has speeded up markedly in the last year, in part because of the remarkable benefits obtained by the use of coarse-grained methodology that despite being very important for this thesis work, is not easily publishable by itself. All this justify that most of the results are still in the publication phase.

Preliminary approach to neutron instrument selecction at ESSB-Bilbao based on experience at ISIS molecular spectroscopy group

Collaborative efforts between the Neutronics and Target Design Group at the Instituto de Fusión Nuclear and the Molecular Spectroscopy Group at the ISIS Pulsed Neutron and Muon Source date back to 2012 in the context of the ESS-Bilbao project. The rationale for these joint activities was twofold, namely: to assess the realm of applicability of the low-energy neutron source proposed by ESS-Bilbao - for details; and to explore instrument capabilities for pulsed-neutron techniques in the range 0.05-3 ms, a time range where ESS-Bilbao and ISIS could offer a significant degree of synergy and complementarity. As part of this collaboration, J.P. de Vicente has spent a three-month period within the ISIS Molecular Spectroscopy Group, to gain hands-on experience on the practical aspects of neutron-instrument design and the requisite neutron-transport simulations. To date, these activities have resulted in a joint MEng thesis as well as a number of publications and contributions to national and international conferences. Building upon these previous works, the primary aim of this report is to provide a self-contained discussion of general criteria for instrument selection at ESS-Bilbao, the first accelerator-driven, low-energy neutron source designed in Spain. To this end, Chapter 1 provides a brief overview of the current design parameters of the accelerator and target station. Neutron moderation is covered in Chapter 2, where we take a closer look at two possible target-moderator-reflector configurations and pay special attention to the spectral and temporal characteristics of the resulting neutron pulses. This discussion provides a necessary starting point to assess the operation of ESSB in short- and long-pulse modes. These considerations are further explored in Chapter 3, dealing with the primary characteristics of ESS-Bilbao as a short- or long-pulse facility in terms of accessible dynamic range and spectral resolution. Other practical aspects including background suppression and the use of fast choppers are also discussed. The guiding principles introduced in the first three chapters are put to use in Chapter 4 where we analyse in some detail the capabilities of a small-angle scattering instrument, as well as how specific scientific requirements can be mapped onto the optimal use of ESS-Bilbao for condensed-matter research. Part 2 of the report contains additional supporting documentation, including a description of the ESSB McStas component, a detailed characterisation of moderator response and neutron pulses, and estimates ofparameters associated with the design and operation of neutron choppers. In closing this brief foreword, we wish to thank both ESS-Bilbao and ISIS for their continuing encouragement and support along the way.

Neutronic design for ESS-Bilbao neutron source

The European Spallation Source-Bilbao (ESS-Bilbao) project plans to build an accelerator facility compliant with the ESS-AB requirements which will be able to drive several experimental stations for research purposes involving intense proton beams with currents up to 75 mA, 50 MeV of final energy, 1.5 ms of pulse length and up to 50 Hz repetition rate. The accelerator will also drive a compact neutron source which will provide useful neutron beams to carry out experiments on moderator optimization, neutron optics devices and general neutron instrumentation as well as preparation work for experiments to be carried out by neutron beam users at the large facilities.

Analysis of Neutron Thermal Scattering Data Uncertainties in PWRs

Analysis of Neutron Thermal Scattering Data Uncertainties in PWRs

Application of a Bayesian/Generalised Least-Squares method to generate correlations between independent neutron fission yield data

Fission product yields are fundamental parameters for several nuclear engineering calculations and in particular for burn-up/activation problems. The impact of their uncertainties was widely studied in the past and valuations were released, although still incomplete. Recently, the nuclear community expressed the need for full fission yield covariance matrices to produce inventory calculation results that take into account the complete uncertainty data. In this work, we studied and applied a Bayesian/generalised least-squares method for covariance generation, and compared the generated uncertainties to the original data stored in the JEFF-3.1.2 library. Then, we focused on the effect of fission yield covariance information on fission pulse decay heat results for thermal fission of 235U. Calculations were carried out using different codes (ACAB and ALEPH-2) after introducing the new covariance values. Results were compared with those obtained with the uncertainty data currently provided by the library. The uncertainty quantification was performed with the Monte Carlo sampling technique. Indeed, correlations between fission yields strongly affect the statistics of decay heat. Introduction Nowadays, any engineering calculation performed in the nuclear field should be accompanied by an uncertainty analysis. In such an analysis, different sources of uncertainties are taken into account. Works such as those performed under the UAM project (Ivanov, et al., 2013) treat nuclear data as a source of uncertainty, in particular cross-section data for which uncertainties given in the form of covariance matrices are already provided in the major nuclear data libraries. Meanwhile, fission yield uncertainties were often neglected or treated shallowly, because their effects were considered of second order compared to cross-sections (Garcia-Herranz, et al., 2010). However, the Working Party on International Nuclear Data Evaluation Co-operation (WPEC)

Testing JEFF-3.1.1 and ENDF/B-VII.1 Decay and Fission Yield Nuclear Data Libraries with Fission Pulse Neutron Emission and Decay Heat Experiments

The aim of this work is to test the present status of Evaluated Nuclear Decay and Fission Yield Data Libraries to predict decay heat and delayed neutron emission rate, average neutron energy and neutron delayed spectra after a neutron fission pulse. Calculations are performed with JEFF-3.1.1 and ENDF/B-VII.1, and these are compared with experimental values. An uncertainty propagation assessment of the current nuclear data uncertainties is performed.

Propagation of Neutron Cross Section, Fission Yield, and Decay Data Uncertainties in Depletion Calculations

Propagation of nuclear data uncertainties in reactor calculations is interesting for design purposes and libraries evaluation. Previous versions of the GRS XSUSA library propagated only neutron cross section uncertainties. We have extended XSUSA uncertainty assessment capabilities by including propagation of fission yields and decay data uncertainties due to the their relevance in depletion simulations. We apply this extended methodology to the UAM6 PWR Pin-Cell Burnup Benchmark, which involves uncertainty propagation through burnup.

3D segmentations of neuronal nuclei from confocal microscope image stacks

In this paper, we present an algorithm to create 3D segmentations of neuronal cells from stacks of previously segmented 2D images. The idea behind this proposal is to provide a general method to reconstruct 3D structures from 2D stacks, regardless of how these 2D stacks have been obtained. The algorithm not only reuses the information obtained in the 2D segmentation, but also attempts to correct some typical mistakes made by the 2D segmentation algorithms (for example, under segmentation of tightly-coupled clusters of cells). We have tested our algorithm in a real scenario?the segmentation of the neuronal nuclei in different layers of the rat cerebral cortex. Several representative images from different layers of the cerebral cortex have been considered and several 2D segmentation algorithms have been compared. Furthermore, the algorithm has also been compared with the traditional 3D Watershed algorithm and the results obtained here show better performance in terms of correctly identified neuronal nuclei.

Review and comparison of effective delayed neutron fraction calculation methods with Monte Carlo codes

The calculation of the effective delayed neutron fraction, beff , with Monte Carlo codes is a complex task due to the requirement of properly considering the adjoint weighting of delayed neutrons. Nevertheless, several techniques have been proposed to circumvent this difficulty and obtain accurate Monte Carlo results for beff without the need of explicitly determining the adjoint flux. In this paper, we make a review of some of these techniques; namely we have analyzed two variants of what we call the k-eigenvalue technique and other techniques based on different interpretations of the physical meaning of the adjoint weighting. To test the validity of all these techniques we have implemented them with the MCNPX code and we have benchmarked them against a range of critical and subcritical systems for which either experimental or deterministic values of beff are available. Furthermore, several nuclear data libraries have been used in order to assess the impact of the uncertainty in nuclear data in the calculated value of beff .

Neutron spectra and dosimetric assessment around a neutron Howitzer container

The neutron Howitzer container at the Neutron Measurements Laboratory of the Nuclear Engineering Department of the Polytechnic University of Madrid (UPM), is equipped with a 241Am-Be neutron source of 74 GBq in its center. The container allows the source to be in either the irradiation or the storage position. To measure the neutron fluence rate spectra around the Howitzer container, measurements were performed using a Bonner spheres spectrometer and the spectra were unfolded using the NSDann program. A calibrated neutron area monitor LB6411 was used to measure the ambient dose equivalent rates, H*(10). Detailed Monte-Carlo simulations were performed to calculate the measured quantities at the same positions. The maximum relative deviation between simulations and measurements was 19.53%. After validation, the simulated model was used to calculate the equivalent dose rate in several key organs of a voxel phantom. The computed doses in the skin and lenses of the eyes are within the ICRP recommended dose limits, as is the H*(10) value for the storage position.

Advanced data acquisition system implementation for the ITER Neutron Diagnostic use case using EPICS and FlexRIO technology on a PXIe platform

In the framework of the ITER Control Breakdown Structure (CBS), Plant System Instrumentation & Control (I&C) defines the hardware and software required to control one or more plant systems [1]. For diagnostics, most of the complex Plant System I&C are to be delivered by ITER Domestic Agencies (DAs). As an example for the DAs, ITER Organization (IO) has developed several use cases for diagnostics Plant System I&C that fully comply with guidelines presented in the Plant Control Design Handbook (PCDH) [2]. One such use case is for neutron diagnostics, specifically the Fission Chamber (FC), which is responsible for delivering time-resolved measurements of neutron source strength and fusion power to aid in assessing the functional performance of ITER [3]. ITER will deploy four Fission Chamber units, each consisting of three individual FC detectors. Two of these detectors contain Uranium 235 for Neutron detection, while a third "dummy" detector will provide gamma and noise detection. The neutron flux from each MFC is measured by the three methods: . Counting Mode: measures the number of individual pulses and their location in the record. Pulse parameters (threshold and width) are user configurable. . Campbelling Mode (Mean Square Voltage): measures the RMS deviation in signal amplitude from its average value. .Current Mode: integrates the signal amplitude over the measurement period