Influence of energy and pulse repetition rate of Er : YAG laser on enamel ablation ability and morphological analysis of the laser-irradiated surface

Objective: To assess the influence of energy and pulse repetition rate of Er:YAG laser on the enamel ablation ability and substrate morphology. Methods: Fifteen crowns of molars were sectioned in four fragments, providing 60 samples, which were ground to flatten the enamel surface. The initial mass was obtained by weighing the fragments. The specimens were hydrated for I h, fixed, and a 3-mm-diameter area was delimited. Twelve groups were randomly formed according to the combination of laser energies (200, 250, 300, or 350 mJ) and pulse repetition rates (2, 3, or 4 Hz). The final mass was obtained and mass loss was calculated by the difference between the initial and final mass. The specimens were prepared for SEM. Data were submitted to ANOVA and Scheffe test. Results: The 4 Hz frequency resulted in higher mass loss and was statistically different from 2 and 3 Hz (p < 0.05). The increase of frequency produced more melted areas, cracks, and unselective and deeper ablation. The 350 mJ energy promoted greater mass loss, similar to 300 mJ. Conclusions: The pulse repetition rate influenced more intensively the mass loss and morphological alteration. Among the tested parameters, 350 mJ/3 Hz improved the ability of enamel ablation with less surface morphological alterations. (C) 2007 Wiley Periodicals, Inc. J Biomed Mater Res.

Effect of Two Restorative Materials on Root Dentine Erosion

This study sought to evaluate the microhardness of root dentine adjacent to glass-ionomer and composite resin restorations after erosive challenge. A crossover study was performed in two phases of 4 consecutive days each. One hundred twelve bovine root dentine slabs were obtained, and standardized box-shaped cavities were prepared at center of each specimen. The prepared cavities were randomly restored with glass-ionomer cement or composite resin. The slabs were randomly assigned among 14 volunteers, which wore intraoral palatal device containing four restored root dentin slabs. Starting on the second day, half of the palatal acrylic devices were immersed extraorally in a lemonade-like carbonated soft drink for 90 s, four times daily for 3 days. Alter 3-day wash-out, dentine slabs restored with the alternative material were placed into palatal appliance and the volunteers started the second phase of this study. After erosive challenges. microhardness measurements were performed. Regardless of the restorative material employed, eroded specimens demonstrated lower microhardness value (p < 0.0001). At eroded condition examined in this study, dentine restored with glass-ionomer cement showed higher microhardness values (p < 0.0001). It may be concluded that the glass-ionomer cement decreases the progression of root dentine erosion at restoration margin. (C) 2010 Wiley Periodicals, Inc J Biomed Mater Res Part B Appl Biomater 93B 304-305, 2010

Histological evaluation of chitosan-based biomaterials used for the correction of critical size defects in rat`s calvaria

Chitosan, a biopolymer obtained from chitin, and its derivates, such as chitosan hydrochloride, has been reported as wound healing accelerators and as possible bone substitutes for tissue engineering, and therefore these Substances could be relevant in dentistry and periodontology. The purpose of this investigation was to make a histological evaluation of chitosan and chitosan hydrochloride biomaterials (gels) used in the correction of critical size bone defects made in rat`s calvaria. Bone defects of 8 mm in diameter were surgically created in the calviria of 50 Holtzman (Rattus norvegicus) rats and filled with blood clot (control), low molecular weight chitosan, high molecular weight chitosan, low molecular weight chitosan hydrochloride, and high molecular weight chitosan hydrochloride, numbering 10 animals, divided into two experimental periods (15 and 60 days), for each biomaterial. The histological evaluation was made based on the morphology of the new-formed tissues in defect`s region, and the results indicated that there was no statistical difference between the groups when the new bone formation in the entire defect`s area were compared (p > 0.05) and, except in the control groups, assorted degrees of inflammation Could be Seen. In Conclusion, chitosan and chitosan hydrochloride biomaterials used in this study were not able to promote new bone formation in critical size defects made in rat`s calvaria. (C) 2009 Wiley Periodicals, Inc. J Biomed Mater Res 93A: 107-114, 2016

Preliminary studies on the effects of d-limonene to workers of the leaf-cutting ant Atta sexdens rubropilosa and its implications for control

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Os conflitos de competência normativa do estado regulador brasileiro no setor administrado pela ANP

The dissertation has by objective describe the administrative activity of regulation exercised by independent regulatory agencies, observing that this activity was already done before this structures creation, however, after a really deep administrative reform that had as objective built a Public Administration with more efficiency, it passed to be done with some own peculiarities of these new structures of regulation. The work gave especial attention to what concern the conflicts of normative competency that really often happen between ANP (Agência Nacional do Petróleo, Gás Natural e Biocombustíveis) and the legislatives organs of the Republic Federative of Brazil, because energetic area has unbelievable mater to any country, and the fact of some juridical norm be against the law and be accepted is very dangerous, it affronts the constitutional principle of the legality e may put in risk the democratic Estate of law, them, regulatory dogmatic must be scientifically knows, and developed, thought and especially there are so many doctrinaires divergences about regulation constitutionality. As a theorist point, the investigation got the Logical nocontradiction principle, according Hans Kelsen and Lourival Vilanova thought, doing a philosophical reflection about the system of positive law, in which there are many antinomies, or conflicts of norms, what include the conflicts of the administrative acts expedited by ANP and the legislation of the brazilian regulatory Estate. For a better understanding and exemplify some perplexities treated by the doctrinaire angle, this work did a lucubration about a possibility of a normative conflict between a ANP resolution and the municipal legislation in a specific case, also, brought several jurisprudences for the brazilians courts of justice, that confirm the empiric existence of normative conflicts among ANP s administrative norms and federal legislation. Finally, concludes observing that the regulation is not a legislative competency delegation to regulatory agencies, is just a new exercise of the administrative function, it is a technical specialization of the public administration, that using this know-how can acting with more efficiency, however the normative power of regulatory agencies must respect the empire of law, so in this terms, the dissertation suggests the ponderation of the constitutionals principles of efficiency and legality how form to harmonizing the democratic legitimate inherent to legal norm supremacy, with the perspective of an efficient economic and institutional development

Desempenho de cultivares de alface crespa em dois ambientes de cultivo em sistema hidropônico

Este trabalho foi desenvolvido em Ribeirão Preto-SP, de 06/02 a 07/04 de 2006. O objetivo foi avaliar o desempenho de cinco cultivares de alface (Pira Roxa, Belíssima, Locarno, Crespona Gigante e Verônica) em dois ambientes de cultivo (casa de vegetação climatizada e não climatizada) em sistema hidropônico NFT. O delineamento experimental foi em blocos casualizados para cada ambiente com três repetições sendo cinco cultivares. Os ambientes foram comparados por meio de análise conjunta. Avaliaram-se a massa fresca e seca da parte aérea, massas fresca e seca do caule, massa fresca e seca da raiz, número de folhas maiores que 10 cm e número total de folhas. Não houve efeito significativo da interação cultivares e ambientes, demonstrando que as cultivares tiveram comportamento similar em ambos os ambientes.

Biology and fertility life table of the South American fruit fly Anastrepha fraterculus on grape

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação da queima e da adição de milho desintegrado com palha e sabugo na ensilagem de cana-de-açúcar

Neste trabalho, avaliou-se a fermentação da cana-de-açúcar queimada, ensilada com ou sem uso de aditivo seco. Os tratamentos (seis no total) consistiram da silagem de cana crua ou queimada, adicionada de 0, 50 ou 100 g/kg de milho desintegrado com palha e sabugo (MDPS), com base no peso verde da forragem. Foram determinados os teores de MS, PB, nitrogênio insolúvel em detergente ácido (NIDA), FDN, FDA, celulose, hemicelulose e lignina. Na avaliação das características fermentativas, foram determinados os valores de carboidratos solúveis, o poder tamponante, o pH e as concentrações de nitrogênio amoniacal e etanol. Como características microbiológicas, avaliou-se o desenvolvimento de leveduras. A inclusão de MDPS elevou os teores de MS e reduziu discretamente os teores de N-NH3 e etanol das silagens, não ocasionando efeito nos valores de pH e na população de leveduras. A presença do fogo reduziu a concentração de MS das silagens, elevou os teores de etanol e leveduras e diminuiu os teores de N-NH3. A fermentação etanólica durante a ensilagem não foi controlada com a inclusão de aditivo seco ou com o uso do fogo.

Reguladores de crescimento vegetal na concentração de macronutrientes em videira Itália

Em clima tropical semi-árido, o uso de reguladores vegetais em fruteiras permite o manejo do crescimento vegetativo, tão necessário ao escalonamento da produção e ao aumento da fertilidade das gemas. Estas substâncias influenciam vários fenômenos fisiológicos relacionados com a absorção mineral, como a condutância de membrana e utilização metabólica de íons. O objetivo deste trabalho foi avaliar o crescimento vegetativo, produção de matéria seca dos ramos, concentração e quantidade acumulada de N, P, K, Ca e Mg nos ramos e nos pecíolos e produção de panículas florais em resposta ao uso de reguladores vegetais, em plantas de videira da cultivar Itália. No experimento foram avaliados três ciclos vegetativos e cinco tratamentos (controle, chlormequat - 1500 mg L-1; daminozide - 3000 mg L-1; uniconazole - 30 mg L-1 e cloreto de mepiquat - 300 mg L-1), aplicados nas plantas em pulverizações aos 35 e 70 dias após a poda. Com o chlormequat e o uniconazole ocorreu efeito cumulativo nas plantas, quando aplicados em ciclos sucessivos da cultura, favorecendo o acúmulo de nutrientes e a diferenciação de gemas férteis em comparação com as plantas controle das videiras 'Itália'. Embora o daminozide tenha inibido significativamente o crescimento das plantas, não resultou em maior acúmulo de nutrientes e emissão de panículas florais nas plantas tratadas.

Latex use as an occlusive membrane for guided bone regeneration

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Conventional and microwave sintering of CaCu(3)Ti(4)O(12)/CaTiO(3) ceramic composites: non-ohmic and dielectric properties

The non-ohmic and dielectric properties as well as the dependence on the microstructural features of CaCu(3)Ti(4)O(12)/CaTiO(3) ceramic composites obtained by conventional and microwave sintering were investigated. It was demonstrated that the non-ohmic and dielectric properties depend strongly on the sintering conditions. It was found that the non-linear coefficient reaches values of 65 for microwave-sintered samples and 42 for samples sintered in a conventional furnace when a current density interval of 1-10 mA cm(-2) is considered. The non-linear coefficient value of 65 is equivalent to 1500 for samples sintered in the microwave if a current interval of 5-30 mA is considered as is shortly discussed by Chung et al (2004 Nature Mater. 3 774). Due to a high non-linear coefficient and a low leakage current (90 mu A) under both processing conditions, these samples are promising for varistor applications. The conventionally sintered samples exhibit a higher relative dielectric constant at 1 kHz (2960) compared with the samples sintered in the microwave furnace (2100). At high frequencies, the dielectric constant is also larger in the samples sintered in the conventional furnace. Depending on the application, one or another synthesis methodology is recommended, that is, for varistor applications sintered in a microwave furnace and for dielectric application sintered in a conventional furnace.

Modeling and Experimental Aspects of Self-healing Bolted Joint through Shape Memory Alloy Actuators

Bolted joints are a form of mechanical coupling largely used in machinery due to their reliability and low cost. Failure of bolted joints can lead to catastrophic events, such as leaking, train derailments, aircraft crashes, etc. Most of these failures occur due to the reduction of the pre-load, induced by mechanical vibration or human errors in the assembly or maintenance process. This article investigates the application of shape memory alloy (SMA) washers as an actuator to increase the pre-load on loosened bolted joints. The application of SMA washer follows a structural health monitoring procedure to identify a damage (reduction in pre-load) occurrence. In this article, a thermo-mechanical model is presented to predict the final pre-load achieved using this kind of actuator, based on the heat input and SMA washer dimension. This model extends and improves on the previous model of Ghorashi and Inman [2004, "Shape Memory Alloy in Tension and Compression and its Application as Clamping Force Actuator in a Bolted Joint: Part 2 - Modeling," J. Intell. Mater. Syst. Struct., 15:589-600], by eliminating the pre-load term related to nut turning making the system more practical. This complete model is a powerful but complex tool to be used by designers. A novel modeling approach for self-healing bolted joints based on curve fitting of experimental data is presented. The article concludes with an experimental application that leads to a change in joint assembly to increase the system reliability, by removing the ceramic washer component. Further research topics are also suggested.

Desenvolvimento de dobras e falhas em ambiente distensional: Aplicação da modelagem física

The geological modeling allows, at laboratory scaling, the simulation of the geometric and kinematic evolution of geological structures. The importance of the knowledge of these structures grows when we consider their role in the creation of traps or conduits to oil and water. In the present work we simulated the formation of folds and faults in extensional environment, through physical and numerical modeling, using a sandbox apparatus and MOVE2010 software. The physical modeling of structures developed in the hangingwall of a listric fault, showed the formation of active and inactive axial zones. In consonance with the literature, we verified the formation of a rollover between these two axial zones. The crestal collapse of the anticline formed grabens, limited by secondary faults, perpendicular to the extension, with a curvilinear aspect. Adjacent to these faults we registered the formation of transversal folds, parallel to the extension, characterized by a syncline in the fault hangingwall. We also observed drag folds near the faults surfaces, these faults are parallel to the fault surface and presented an anticline in the footwall and a syncline hangingwall. To observe the influence of geometrical variations (dip and width) in the flat of a flat-ramp fault, we made two experimental series, being the first with the flat varying in dip and width and the second maintaining the flat variation in width but horizontal. These experiments developed secondary faults, perpendicular to the extension, that were grouped in three sets: i) antithetic faults with a curvilinear geometry and synthetic faults, with a more rectilinear geometry, both nucleated in the base of sedimentary pile. The normal antithetic faults can rotate, during the extension, presenting a pseudo-inverse kinematics. ii) Faults nucleated at the top of the sedimentary pile. The propagation of these faults is made through coalescence of segments, originating, sometimes, the formation of relay ramps. iii) Reverse faults, are nucleated in the flat-ramp interface. Comparing the two models we verified that the dip of the flat favors a differentiated nucleation of the faults at the two extremities of the mater fault. V These two flat-ramp models also generated an anticline-syncline pair, drag and transversal folds. The anticline was formed above the flat being sub-parallel to the master fault plane, while the syncline was formed in more distal areas of the fault. Due the geometrical variation of these two folds we can define three structural domains. Using the physical experiments as a template, we also made numerical modeling experiments, with flat-ramp faults presenting variation in the flat. Secondary antithetic, synthetic and reverse faults were generated in both models. The numerical modeling formed two folds, and anticline above the flat and a syncline further away of the master fault. The geometric variation of these two folds allowed the definition of three structural domains parallel to the extension. These data reinforce the physical models. The comparisons between natural data of a flat-ramp fault in the Potiguar basin with the data of physical and numerical simulations, showed that, in both cases, the variation of the geometry of the flat produces, variation in the hangingwall geometry

Bone healing in critical-size defects treated with new bioactive glass/calcium sulfate: A histologic and histometric study in rat calvaria

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Long-term effect of carbodiimide on dentin matrix and resin-dentin bonds

Objectives: To characterize the interaction of 1-Ethyl-3-[3-dimethylaminopropyl] carbodiimide Hydrochloride (EDC) with dentin matrix and its effect on the resin-dentin bond. Methods: Changes to the stiffness of demineralized dentin fragments treated with EDC/N-hydroxysuccinimide (NHS) in different solutions were evaluated at different time points. The resistance against enzymatic degradation was indirectly evaluated by ultimate tensile strength (UTS) test of demineralized dentin treated or not with EDC/NHS and subjected to collagenase digestion. Short- and long-term evaluations of the strength of resin-dentin interfaces treated with EDC/NHS for 1 h were performed using microtensile bond strength (mu TBS) test. All data (MPa) were individually analyzed using ANOVA and Tukey HSD tests (alpha = 0.05). Results: The different exposure times significantly increased the stiffness of dentin (p < 0.0001, control-5.15 and EDC/NHS-29.50), while no differences were observed among the different solutions of EDC/NHS (p = 0.063). Collagenase challenge did not affect the UTS values of EDC/NHS group (6.08) (p > 0.05), while complete degradation was observed for the control group (p = 0.0008, control-20.84 and EDC/NHS-43.15). EDC/NHS treatment did not significantly increase resin-dentin mu TBS, but the values remained stable after 12 months water storage (p < 0.05). Conclusions: Biomimetic use of EDC/NHS to induce exogenous collagen cross-links resulted in increased mechanical properties and stability of dentin matrix and dentin-resin interfaces. (C) 2010 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 94B: 250-255, 2010.