Heat fluxes and surface radiation measurements from Samoylov Island, Lena Delta, Siberia, April to September 2007

In this article, we present a study on the surface energy balance of a polygonal tundra landscape in northeast Siberia. The study was performed during half-year periods from April to September in each of 2007 and 2008. The surface energy balance is obtained from independent measurements of the net radiation, the turbulent heat fluxes, and the ground heat flux at several sites. Short-wave radiation is the dominant factor controlling the magnitude of all the other components of the surface energy balance during the entire observation period. About 50% of the available net radiation is consumed by the latent heat flux, while the sensible and the ground heat flux are each around 20 to 30%. The ground heat flux is mainly consumed by active layer thawing. About 60% of the energy storage in the ground is attributed to the phase change of soil water. The remainder is used for soil warming down to a depth of 15 m. In particular, the controlling factors for the surface energy partitioning are snow cover, cloud cover, and the temperature gradient in the soil. The thin snow cover melts within a few days, during which the equivalent of about 20% of the snow-water evaporates or sublimates. Surface temperature differences of the heterogeneous landscape indicate spatial variabilities of sensible and latent heat fluxes, which are verified by measurements. However, spatial differences in the partitioning between sensible and latent heat flux are only measured during conditions of high radiative forcing, which only occur occasionally.

Flujo de potencia entre estructuras complejas sometidas a excitaciones de alta frecuencia y aplicaciones a la detección de daño estructural

El tema central de investigación en esta Tesis es el estudio del comportamientodinámico de una estructura mediante modelos que describen la distribución deenergía entre los componentes de la misma y la aplicación de estos modelos parala detección de daños incipientes.Los ensayos dinámicos son un modo de extraer información sobre las propiedadesde una estructura. Si tenemos un modelo de la estructura se podría ajustar éstepara que, con determinado grado de precisión, tenga la misma respuesta que elsistema real ensayado. Después de que se produjese un daño en la estructura,la respuesta al mismo ensayo variará en cierta medida; actualizando el modelo alas nuevas condiciones podemos detectar cambios en la configuración del modeloestructural que nos condujeran a la conclusión de que en la estructura se haproducido un daño.De este modo, la detección de un daño incipiente es posible si somos capacesde distinguir una pequeña variación en los parámetros que definen el modelo. Unrégimen muy apropiado para realizar este tipo de detección es a altas frecuencias,ya que la respuesta es muy dependiente de los pequeños detalles geométricos,dado que el tamaño característico en la estructura asociado a la respuesta esdirectamente proporcional a la velocidad de propagación de las ondas acústicas enel sólido, que para una estructura dada es inalterable, e inversamente proporcionala la frecuencia de la excitación. Al mismo tiempo, esta característica de la respuestaa altas frecuencias hace que un modelo de Elementos Finitos no sea aplicable enla práctica, debido al alto coste computacional.Un modelo ampliamente utilizado en el cálculo de la respuesta de estructurasa altas frecuencias en ingeniería es el SEA (Statistical Energy Analysis). El SEAaplica el balance energético a cada componente estructural, relacionando la energíade vibración de estos con la potencia disipada por cada uno de ellos y la potenciatransmitida entre ellos, cuya suma debe ser igual a la potencia inyectada a cadacomponente estructural. Esta relación es lineal y viene caracterizada por los factoresde pérdidas. Las magnitudes que intervienen en la respuesta se consideranpromediadas en la geometría, la frecuencia y el tiempo.Actualizar el modelo SEA a datos de ensayo es, por lo tanto, calcular losfactores de pérdidas que reproduzcan la respuesta obtenida en éste. Esta actualización,si se hace de manera directa, supone la resolución de un problema inversoque tiene la característica de estar mal condicionado. En la Tesis se propone actualizarel modelo SEA, no en término de los factores de pérdidas, sino en términos deparámetros estructurales que tienen sentido físico cuando se trata de la respuestaa altas frecuencias, como son los factores de disipación de cada componente, susdensidades modales y las rigideces características de los elementos de acoplamiento.Los factores de pérdidas se calculan como función de estos parámetros. Estaformulación es desarrollada de manera original en esta Tesis y principalmente sefunda en la hipótesis de alta densidad modal, es decir, que en la respuesta participanun gran número de modos de cada componente estructural.La teoría general del método SEA, establece que el modelo es válido bajounas hipótesis sobre la naturaleza de las excitaciones externas muy restrictivas,como que éstas deben ser de tipo ruido blanco local. Este tipo de carga es difícil dereproducir en condiciones de ensayo. En la Tesis mostramos con casos prácticos queesta restricción se puede relajar y, en particular, los resultados son suficientementebuenos cuando la estructura se somete a una carga armónica en escalón.Bajo estas aproximaciones se desarrolla un algoritmo de optimización por pasosque permite actualizar un modelo SEA a un ensayo transitorio cuando la carga esde tipo armónica en escalón. Este algoritmo actualiza el modelo no solamente parauna banda de frecuencia en particular sino para diversas bandas de frecuencia demanera simultánea, con el objetivo de plantear un problema mejor condicionado.Por último, se define un índice de daño que mide el cambio en la matriz depérdidas cuando se produce un daño estructural en una localización concreta deun componente. Se simula numéricamente la respuesta de una estructura formadapor vigas donde producimos un daño en la sección de una de ellas; como se tratade un cálculo a altas frecuencias, la simulación se hace mediante el Método delos Elementos Espectrales para lo que ha sido necesario desarrollar dentro de laTesis un elemento espectral de tipo viga dañada en una sección determinada. Losresultados obtenidos permiten localizar el componente estructural en que se haproducido el daño y la sección en que éste se encuentra con determinado grado deconfianza.AbstractThe main subject under research in this Thesis is the study of the dynamic behaviourof a structure using models that describe the energy distribution betweenthe components of the structure and the applicability of these models to incipientdamage detection.Dynamic tests are a way to extract information about the properties of astructure. If we have a model of the structure, it can be updated in order toreproduce the same response as in experimental tests, within a certain degree ofaccuracy. After damage occurs, the response will change to some extent; modelupdating to the new test conditions can help to detect changes in the structuralmodel leading to the conclusión that damage has occurred.In this way incipient damage detection is possible if we are able to detect srnallvariations in the model parameters. It turns out that the high frequency regimeis highly relevant for incipient damage detection, because the response is verysensitive to small structural geometric details. The characteristic length associatedwith the response is proportional to the propagation speed of acoustic waves insidethe solid, but inversely proportional to the excitation frequency. At the same time,this fact makes the application of a Finite Element Method impractical due to thehigh computational cost.A widely used model in engineering when dealing with the high frequencyresponse is SEA (Statistical Energy Analysis). SEA applies the energy balance toeach structural component, relating their vibrational energy with the dissipatedpower and the transmitted power between the different components; their summust be equal to the input power to each of them. This relationship is linear andcharacterized by loss factors. The magnitudes considered in the response shouldbe averaged in geometry, frequency and time.SEA model updating to test data is equivalent to calculating the loss factorsthat provide a better fit to the experimental response. This is formulated as an illconditionedinverse problem. In this Thesis a new updating algorithm is proposedfor the study of the high frequency response regime in terms of parameters withphysical meaning such as the internal dissipation factors, modal densities andcharacteristic coupling stiffness. The loss factors are then calculated from theseparameters. The approach is developed entirely in this Thesis and is mainlybased on a high modal density asumption, that is to say, a large number of modescontributes to the response.General SEA theory establishes the validity of the model under the asumptionof very restrictive external excitations. These should behave as a local white noise.This kind of excitation is difficult to reproduce in an experimental environment.In this Thesis we show that in practical cases this assumption can be relaxed, inparticular, results are good enough when the structure is excited with a harmonicstep function.Under these assumptions an optimization algorithm is developed for SEAmodel updating to a transient test when external loads are harmonic step functions.This algorithm considers the response not only in a single frequency band,but also for several of them simultaneously.A damage index is defined that measures the change in the loss factor matrixwhen a damage has occurred at a certain location in the structure. The structuresconsidered in this study are built with damaged beam elements; as we are dealingwith the high frequency response, the numerical simulation is implemented witha Spectral Element Method. It has therefore been necessary to develop a spectralbeam damaged element as well. The reported results show that damage detectionis possible with this algorithm, moreover, damage location is also possible withina certain degree of accuracy.

Evapotranspiration of grapevine trained to a gable trellis system under netting and black plastic mulching

The evapotranspiration (ET c) of a table grape vineyard (Vitis vinifera, cv. Red Globe) trained to a gable trellis under netting and black plastic mulching was determined under semiarid conditions in the central Ebro River Valley during 2007 and 2008. The netting was made of high-density polyethylene (pores of 12 mm2) and was placed just above the ground canopy about 2.2 m above soil surface. Black plastic mulching was used to minimize soil evaporation. The surface renewal method was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Later, latent heat flux (LE) values were obtained by solving the energy balance equation. For the May–October period, seasonal ET c was about 843 mm in 2007 and 787 mm in 2008. The experimental weekly crop coefficients (K cexp) fluctuated between 0.64 and 1.2. These values represent crop coefficients adjusted to take into account the reduction in ET c caused by the netting and the black plastic mulching. Average K cexp values during mid- and end-season stages were 0.79 and 0.98, respectively. End-season K cexp was higher due to combination of factors related to the precipitation and low ET o conditions that are typical in this region during fall. Estimated crop coefficients using the Allen et al. (1998) approach adjusting for the effects of the netting and black plastic mulching (K cFAO) showed a good agreement with the experimental K cexp values.

Evapotranspiration and crop coefficients of rice (Oryza sativa L.) under sprinkler irrigation in a semiarid climate determined by the surface renewal method

The evapotranspiration (ETc) of sprinkler-irrigated rice was determined for the semiarid conditions of NE Spain during 2001, 2002 and 2003. The surface renewal method, after calibration against the eddy covariance method, was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Latent heat flux values were obtained by solving the energy balance equation. Finally, lysimeter measurements were used to validate the evapotranspiration values obtained with the surface renewal method. Seasonal rice evapotranspiration was about 750–800 mm. Average daily ETc for mid-season (from 90 to 130 days after sowing) was 5.1, 4.5 and 6.1 mm day−1 for 2001, 2002 and 2003, respectively. The experimental weekly crop coefficients fluctuated in the range of 0.83–1.20 for 2001, 0.81–1.03 for 2002 and 0.84–1.15 for 2003. The total growing season was about 150–160 days. In average, the crop coefficients for the initial (Kcini), mid-season (Kcmid) and late-season stages (Kcend) were 0.92, 1.06 and 1.03, respectively, the length of these stages being about 55, 45 and 25 days, respectively.

Biostimulation methods associated with early weaning and reproductive rhythms in primiparous rabbit does

El objetivo general de esta Tesis Doctoral ha sido tratar de mejorar los parámetros reproductivos de las conejas primíparas lactantes, empleando dos métodos de manejo (destete temprano y extensificación del ritmo reproductivo), que están directamente relacionados con su balance energético. Para ello, se diseñaron 2 experimentos en este tipo de hembras. En el primero, se estudió el efecto del destete a 25 días post-parto (dpp) sobre la actividad ovárica y el metabolismo energético de las conejas una semana más tarde (32 dpp). Un total de 34 primíparas lactantes con 8 gazapos fueron distribuidas en tres grupos: 10 conejas se sacrificaron a los 25 dpp (grupo L25), 13 fueron destetadas a los 25 dpp y sacrificadas a los 32 dpp (grupo NL32), y 11 conejas no se destetaron y fueron sacrificadas a los 32 dpp (grupo L32). No se observaron diferencias significativas entre grupos en el peso corporal, el peso del ovario, ni en las concentraciones séricas de ácidos grasos no esterificados y de proteínas totales. A pesar de que el grupo NL32 presentó un bajo consumo de alimento (122 ± 23,5 g / día, p <0,001), su contenido corporal estimado de lípidos (16,9 ± 1,09%, P <0,008), proteínas (19,7 ± 0,07%, P <0,0001), y energía (1147 ± 42,7 MJ / kg, p <0,006) fueron más elevados y las concentraciones séricas de glucosa (158 ± 24,5 mg/dl, p <0,04) más bajas que en los grupos L25 (11,9 ± 1,3%, 18,5 ± 0,08%, 942 ± 51,3 MJ/kg y 212 ± 27,9 mg/dl) y L32 (13,4 ± 1,03%, 18,5 ± 0,1%, 993 ± 40,4 MJ/kg y 259 ± 29,5 mg/dl), respectivamente. En el grupo L25 se observó un menor número medio de folículos ≥ 1 mm en la superficie ovárica en comparación con los grupos NL32 y L32 (12,7 ± 1,5 vs. 18,0 ± 1,45 y 17,6 ± 1,67, p <0,05). La población folicular ovárica en las secciones histológicas y la inmunolocalización de los receptores de prolactina fueron similares en todos los grupos. En el grupo L25, tanto la maduración nuclear de oocitos, medida en términos de tasas alcanzadas de Metafase II (67,0 vs. 79,7 y 78,3%, P <0.05) y la maduración citoplasmática, medida por el porcentaje de gránulos corticales (GC) total o parcialmente migrados en los oocitos, fueron significativamente menores que en los grupos NL32 y L32 (16,0 vs 38,3 y 60,0%, P <0.05). En conclusión, a pesar de que el destete precoz a 25 dpp pareció mejorar las reservas de energía de las conejas primíparas, este hecho no se reflejó claramente a nivel ovárico a los 32 dpp y fue similar independientemente del destete, por lo que éste último podría llevarse a cabo más tarde. En el segundo experimento, se compararon dos ritmos reproductivos. Se utilizaron un total de 48 conejas primíparas lactantes con 8 gazapos que se asignaron al azar en dos grupos experimentales: a) lactantes sacrificadas a comienzos del post-parto (11 dpp) de acuerdo a un ritmo semi-intensivo (n = 24), y b) lactantes sacrificadas al final del período post-parto (25 dpp) de acuerdo con un ritmo más extensivo (n = 24). En ellas, se estudió el peso vivo, la composición corporal estimada, parámetros metabólicos y endocrinos (estradiol y progesterona) y características ováricas como la población folicular y la tasa de atresia, así como la maduración nuclear y citoplásmica de los oocitos. En este estudio, el peso vivo, el contenido de energía corporal, los depósitos grasos y los ácidos grasos no esterificados disminuyeron a lo largo del post-parto con respecto al momento del parto (P <0,05). Las concentraciones séricas de proteínas y glucosa aumentaron en el mismo periodo post-parto (P <0,05). Se observaron similares niveles de estradiol y progesterona en ambos ritmos, así como una población folicular, tasas de maduración nuclear (tasa de oocitos en metafase II) y citoplasmática (porcentaje de oocitos con gránulos corticales migrados), similares en ambos momentos del post-parto. Sin embargo, el número de folículos preovulatorios en la superficie ovárica fue menor (P <0,05) y la tasa de atresia tendió a ser mayor con un porcentaje también menor de folículos sanos (P <0,1) en los ovarios de las hembras sometidas al ritmo extensivo. En conclusión, al final del post-parto (25 días), las conejas primíparas sin destetar muestran un deterioro de sus reservas corporales, de sus parámetros metabólicos séricos y de la calidad de sus oocitos; incluso se ha observado una ligera influencia negativa en el desarrollo de sus folículos ováricos. Por esta razón, se considera que en las conejas primíparas lactantes el manejo reproductivo extensivo (25 dpp) no presenta ninguna ventaja en comparación con el semi-intensivo (11 dpp). A la vista de los resultados de estos dos experimentos, podemos decir que ni el destete temprano, ni la extensificación del ritmo reproductivo han conseguido una mejora en los parámetros reproductivos de una hembra primípara. Por ello, son necesarios más estudios sobre el estado metabólico de la coneja primípara lactante para conseguir métodos o estrategias que lo mejoren y tengan consecuencias directas sobre la actividad reproductiva y sobre su éxito productivo. The general aim of this Thesis was to study two management methods (early weaning and extensive reproductive rhythm) linked to the energy balance of the primiparous rabbit does to improve their reproductive performance. In this sense, 2 experiments were conducted using this kind of females. In the first experiment, the effect of weaning at 25 days post-partum (dpp) on ovarian activity and energetic metabolism one week later (32 dpp) was studied. A total of 34 primiparous lactating rabbit does were used and distributed among three groups: 10 does euthanized at 25 dpp (group L25), 13 does weaned at 25 dpp and euthanized at 32 dpp (group NL32), and 11 non weaned does euthanized at 32 dpp (group L32). No significant differences were observed in live body weight, ovary weight, serum non esterified fatty acids (NEFA) and total protein concentration among groups. Although NL32 does had a low feed intake (122±23.5 g/Day; P < 0.001), their estimated lipids (16.9±1.09%, P < 0.008), protein (19.7±0.07%, P < 0.0001), and energy (1147±42.7 MJ/kg, P < 0.006) body contents were higher and their serum glucose concentrations (158±24.5 mg/dl, P < 0.04) were lower compared to L25 does (11.9±1.3%, 18.5±0.08%, 942±51.3 MJ/kg and 212±27.9 mg/dl) and L32 does (13.4±1.03%, 18.5±0.1%, 993±40.4 MJ/kg and 259±29.5 mg/dl, respectively). A lower number of follicles ≥1mm was observed compared to NL32 and L32 groups (12.7±1.5 vs. 18.0±1.45 and 17.6 ±1.67; P < 0.05) in the ovarian surface of L25 does. Follicular population in the histological ovarian sections and immunolocalization of prolactin receptor were similar in all groups. In group L25, both nuclear maturation of oocytes in terms of Metaphase II rate (67.0 vs. 79.7 and 78.3%; P < 0.05) and cytoplasmic maturation measured by percentage of cortical granules (CG), totally or partially migrated in oocytes were significantly lower than in groups NL32 and L32 (16.0 vs. 38.3 and 60.0%; P < 0.05). Consequently, a higher rate of oocytes with non-migrated CGs was found in group L25 than in groups NL32 and L32 (76.0 vs. 46.8 and 33.3%; P < 0.05). In conclusion, even though early weaning at 25 dpp seemed to improve body energy stored in primiparous does, this fact was not well reflected on the ovarian status at 32 dpp, which was similar regardless of weaning time. In the second experiment, two reproductive rhythms were compared. A total of 48 primiparous Californian x New Zealand White rabbit does suckling 8 kits were randomly allocated in two experimental groups: a) lactating does euthanized at early post-partum period (11 dpp) according to a semi-intensive rhythm (n = 24), and b) lactating does euthanized on later post-partum period (25 dpp) according to a more extensive rhythm (n = 24). Live weight, estimated body composition, serum metabolic and endocrine parameters (oestradiol and progesterone concentrations) and ovarian features like follicle population and atresia rate, and oocyte maturation were studied. Live weight, body energy content, lipid depots and serum non esterified fatty acids (NEFA) concentrations diminished from parturition time to post-partum period (P < 0.05). In addition, serum protein and glucose concentrations increased along postpartum time (P < 0.05). Similar oestradiol and progesterone levels were shown in rhythms as well as similar follicle population and nuclear and cytoplasmic maturation rates measured as metaphase II and cortical granule migration, respectively in both postpartum times. However, number of preovulatory follicles on the ovarian surface was lower (P < 0.05) and atresia rate tended to be higher with also lower percentage of healthy follicles (P < 0.1) in ovaries of females of extensive group. In conclusion, primiparous non-weaned rabbits does at late post-partum time (25 days), Did no show any improvement regarding body reserves, serum metabolic parameters and oocyte quality; even a slight negative influence has been observed in the development of their ovarian follicles. Thus this reproductive management does not present any advantage compared to earlier post-partum (11 days) reproductive rhythm. In summary, according to the obtained results from these two experiments, we can say that the application of early weaning and the extensive rhythms did not achieve an improvement in the reproductive performance of primiparous does. Thus, it is necessary to conduct more studies about the metabolic status of the primiparous lactating doe to achieve strategies in order to improve it and consequently, to improve the reproductive activity and their productive success.

Estudio energético comparativo de diferentes configuraciones de ciclo combinado

El objetivo del presente proyecto consiste en la modelización y optimización de una planta de gasificación integrada en ciclo combinado de 400 MW de potencia neta, mediante el uso del programa Cycle-Tempo, desarrollado por la Universidad de Delft. Para la modelización de la planta, se ha dividido en sus dos unidades principales: la isla de gasificación y el ciclo combinado. Para la validación del modelo de la isla de gasificación, se ha utilizado una composición de referencia de un combustible gasificable y se ha obtenido la composición del gas de síntesis esperada. Se han modelado y optimizado varias configuraciones de ciclo combinado, variando los parámetros característicos de la caldera de recuperación de calor. Se ha realizado la integración de las dos unidades para maximizar la potencia entregada por la planta. Finalmente, se ha estimado el balance anual de energía del ciclo combinado alimentado con gas natural y con el gas de síntesis, con el fin de comparar las rentabilidades económicas obtenidas. Mediante el estudio realizado, se deduce que la forma más eficiente de producir energía, a partir del uso del carbón, es la tecnología de gasificación integrada en ciclo combinado, pese a que su rendimiento sea inferior al ciclo combinado alimentado con gas natural. ABSTRACT The aim of this project is the modeling and optimization of an integrated gasification combined cycle plant of 400 MW net power, using the Cycle-Tempo program, developed by the University of Delft. For the modeling of the plant, it has been divided into its two main units: the island of gasification and the combined cycle. For the model validation of the gasification island, a reference composition of a gasifiable fuel has been used and the expected synthesis gas composition was obtained. Several configurations of combined cycle have been modeled and optimized by varying the characteristic parameters of the heat recovery steam generator. It has made the integration of the two units to reach maximum optimization of power, which has been delivered by the plant. Finally, it has been estimated the annual energy balance for the combined cycle plant fueled with natural gas and with syngas, in order to compare the profitability obtained with each one. Through the study, it is deduced that the most efficient way to produce energy from the use of coal, is the integrated gasification combined cycle technology, although their performance is lower than that obtained from the combined cycle fueled with natural gas.

Nutrition and physical activity programs for obesity treatment (PRONAF study). methodological approach of the project

Este trabajo aborda la metodología seguida para llevar a cabo el proyecto de investigación PRONAF (Clinical Trials Gov.: number NCT01116856.) Background: At present, scientific consensus exists on the multifactorial etiopatogenia of obesity. Both professionals and researchers agree that treatment must also have a multifactorial approach, including diet, physical activity, pharmacology and/or surgical treatment. These two last ones should be reserved for those cases of morbid obesities or in case of failure of the previous ones. The aim of the PRONAF study is to determine what type of exercise combined with caloric restriction is the most appropriate to be included in overweigth and obesity intervention programs, and the aim of this paper is to describe the design and the evaluation methods used to carry out the PRONAF study. Methods/design: One-hundred nineteen overweight (46 males) and 120 obese (61 males) subjects aged 18–50 years were randomly assigned to a strength training group, an endurance training group, a combined strength + endurance training group or a diet and physical activity recommendations group. The intervention period was 22 weeks (in all cases 3 times/wk of training for 22 weeks and 2 weeks for pre and post evaluation). All subjects followed a hypocaloric diet (25-30% less energy intake than the daily energy expenditure estimated by accelerometry). 29–34% of the total energy intake came from fat, 14–20% from protein, and 50–55% from carbohydrates. The mayor outcome variables assesed were, biochemical and inflamatory markers, body composition, energy balance, physical fitness, nutritional habits, genetic profile and quality of life. 180 (75.3%) subjects finished the study, with a dropout rate of 24.7%. Dropout reasons included: personal reasons 17 (28.8%), low adherence to exercise 3 (5.1%), low adherence to diet 6 (10.2%), job change 6 (10.2%), and lost interest 27 (45.8%). Discussion: Feasibility of the study has been proven, with a low dropout rate which corresponds to the estimated sample size. Transfer of knowledge is foreseen as a spin-off, in order that overweight and obese subjects can benefit from the results. The aim is to transfer it to sports centres. Effectiveness on individual health-related parameter in order to determine the most effective training programme will be analysed in forthcoming publications.

Estudio Energético y de Explotación de diferentes conjuntos de Labranza para el Cultivo de la Yuca (Manihot esculenta, Crantz) en un Fluvisol

El trabajo se desarrolló en tres etapas de investigación, las dos primeras fueron realizadas en la Unidad Básica de Producción Cooperativa “El Palmar” perteneciente a la Empresa de Cultivos Varios "Paquito Rosales Benítez" del municipio de Yara, provincia de Granma, Cuba, el cual se llevó a cabo en el período de abril de 2005 a enero de 2008; y de noviembre de 2012 a febrero de 2013 respectivamente; la tercera se ejecutó de mayo a junio de 2013 en un canal de suelo ubicado en la nave de maquinaria del Departamento de Ingeniería Rural de la Universidad Politécnica de Madrid. En la primera etapa se evaluaron los conjuntos tractor-apero que intervienen en la realización de cuatro sistemas de labranza para el cultivo de la yuca, variedad Enana Rosada. Los sistemas de laboreo fueron: T1, labor de aradura (alzado) con un arado de discos seguidas de un pase de grada de discos un pase cruzado de un escarificador y un pase con una grada de discos (5 labores); T2, laboreo mínimo que comprende una labor profunda con un escarificador con saetas seguido por una labor de grada de discos (2 labores); T3, laboreo mínimo en el que se realizaron dos pases cruzados con escarificador y una labor de fresado con una fresadora de eje horizontal (3 labores) y; T4, dos labores cruzadas con la grada de discos seguidas por otras dos pases cruzados con el escarificador y una última labor con la grada de discos (5 labores). Se realizaron cinco observaciones de la jornada laboral para cada uno de los conjuntos tractorapero de cada sistema de laboreo en tres campañas, evaluando el consumo de combustible, las diferentes productividades, los índices y coeficientes tecnológicos y de explotación, el rendimiento del cultivo el balance energético del mismo, y la emisión de CO2 equivalente. En la segunda etapa se determinó la fuerza de tiro requerida por un órgano de trabajo de un escarificador con saetas en condiciones de campo, en tres profundidades (15, 25 y 35 cm) y a cuatro velocidades de trabajo (1,30; 1,49; 1,65 y 2,32 m s-1). En la tercera etapa se determinaron las fuerzas horizontales y verticales en una maqueta experimental de un órgano de trabajo de un escarificador con saetas (1:5 del tamaño real del apero) en cuatro contenidos de humedad (60, 90, 120 y 150 g kg-1), tres densidades del suelo (1,1; 1,2 y 1,3 Mg m-3) y una velocidad de 40 mm s-1. Se comparan los resultados del apero a tamaño real y la maqueta experimental. Los mejores resultados relacionados con los indicadores evaluados a la maquinaria correspondieron al sistema de laboreo mínimo T2, el cual presenta la mejor productividad por hora de tiempo limpio (1,34 ha h-1) y de tiempo operativo (1,27 ha h-1), con diferencias significativas respecto al resto de los sistemas de labranza evaluados; así como el menor consumo de combustible (32,4 L ha-1) y el mejor comportamiento energético, con diferencias significativas respecto a las demás, resultando inferior en un 63, 30 y 58 % con relación a T1, T3 y T4. La fuerza de tiro del órgano de trabajo del escarificador con saetas se incrementa con la densidad del suelo y con la profundidad, y velocidad de trabajo. Las fuerzas horizontales y verticales de la maqueta se incrementan linealmente con la densidad y humedad del suelo. Existe una relación lineal entre las fuerzas de tiro y horizontales medidas en el apero real y en el apero a escala con el contenido de humedad del suelo. ABSTRACT The work was developed in three stages of research, the first two were conducted in the Basic Unit of Cooperative Production "El Palmar" belonging to the agricultural farm "Paquito Rosales Benitez" in the municipality of Yara, Granma Province, Cuba, the which was conducted in the period from April 2005 to January 2008 and November 2012 and February 2013 respectively, the third from May to June 2013 on a soilbin located in the ship's machinery of Rural Engineering Department of the Technical University of Madrid. In the first stage were evaluated tractor-implement sets involved in the completion of four tillage systems for cassava, Pink Dwarf variety. Tillage systems were: T1, plowing (elevation) with a disk plow followed by a pass of disc harrow, a cross of scarifier and a pass with a disc harrow (5 labours), T2, minimum tillage comprising a deep work with a scarifier with a bolt followed by a disc harrow work (two labours); T3, minimum tillage which two crossed passes performed with scarifier and milling labour with a horizontal axis milling machine (three labours) and, T4, two crossed labours with disc harrow followed by two crossed passes with the scarifier and a final labour with disc harrow (5 labours). Five observations of the working day for each tractor-implement sets of each tillage system in three seasons were performed, evaluating fuel consumption, different productivities, indexes and technological and operational factors, the crop yield energy balance and the emission of CO2 equivalent. In the second stage we determined the draft force required by a working body of a scarifier with bolt under field conditions at three depths (15, 25 and 35 cm) and four operating speeds (1.30, 1.49 , 1.65 and 2.32 m s-1). In the third stage were determined horizontal and vertical forces on an experimental model of a working body of a scarifier with bolt (1:5 real scale of the implement) in four moisture contents (60, 90, 120 and 150 g kg -1), three soil densities (1.1, 1.2, and 1.3 Mg m-3) and a speed of 40 mm s-1.The results of real scale implement the experimental model were compared. The best results related to evaluated machinery indicators corresponded to T2 minimum tillage system, which presents the best productivity per hour clean time (1.34 ha h-1) and operating time (1.27 ha h-1), with significant differences compared to other tillage systems evaluated; as well as lower fuel consumption (32.4 L ha-1) and the best energy performance, with significant differences from the other, resulting lower by 63, 30 and 58% compared to T1, T3 and T4. The draft force of the working body of the scarifier with bolt increases with soil density and depth, and speed of work. The horizontal and vertical forces of the model increase linearly with density and soil moisture. A linear relationship exists between the shot and horizontal forces measured at the real implement and scale implement with the soil moisture content.

Modelization of an experimental solar test box equipped with a water-flow based window

A study on a water- ow window installed in a test box is presented. This window is composed of two glass panes separated by a chamber through water ows. The ow of water comes from an isolated tank which contains heat water. In order to fully evaluate the water- ow window performance for different room and window sizes, locations and weather conditions, a mathematical model of the whole box is needed. The proposed model, in which conduction heat transfer mechanism is the only considered, is one dimensional and unsteady based upon test box energy balance. The effect of the heat water tank, which feeds the water- ow window, is included in the model by means of a time delay in the source term. Although some previous work about moving uid chamber has been developed, air was used as heat transfer uid and no uid storage was considered. Finally a comparison between the numerical solution and the obtained experimental data is done.

Finite volume modelling of an icefield with subglacial lake

Momentum, mass and energy balance laws provide the tools for the study of the evolution of an icefield covering a subglacial lake. The ice is described as a non-Newtonian fluid with a power-law constitutive relationship with temperature- and stress-dependent viscosity (Glen?s law) [1]. The phase transition mechanisms at the air/ice and ice/water interfaces yield moving boundary formulations, and lake hydrodynamics requires equation reduction for treating the turbulence.

A method to obtain the thermal parameters and the photothermal transduction efficiency in an optical hyperthermia device based on laser irradiation of gold nanoparticles

Optical hyperthermia systems based on the laser irradiation of gold nanorods seem to be a promising tool in the development of therapies against cancer. After a proof of concept in which the authors demonstrated the efficiency of this kind of systems, a modeling process based on an equivalent thermal-electric circuit has been carried out to determine the thermal parameters of the system and an energy balance obtained from the time-dependent heating and cooling temperature curves of the irradiated samples in order to obtain the photothermal transduction efficiency. By knowing this parameter, it is possible to increase the effectiveness of the treatments, thanks to the possibility of predicting the response of the device depending on the working configuration. As an example, the thermal behavior of two different kinds of nanoparticles is compared. The results show that, under identical conditions, the use of PEGylated gold nanorods allows for a more efficient heating compared with bare nanorods, and therefore, it results in a more effective therapy.

Diseño de receptor de torre central para generación directa de vapor con perfil de potencia variable longitudinal y transversalmente

En este estudio se ha realizado el diseño de un receptor de una central de Torre Central de energía solar para generación directa de vapor, mediante el uso de métodos numéricos, con un perfil de potencia incidente variable longitudinal y transversalmente. Para ello se ha dividido la geometría del receptor según el método de diferencias finitas, y se ha procedido a resolver las ecuaciones del balance de energía. Una vez resuelto el sistema de ecuaciones se dispone de la distribución de temperaturas en el receptor y se puede proceder a analizar los resultados así como a calcular otros datos de interés. ABSTRACT In this study it has been made a Central Receiver Solar Thermal Power Plant’s Receiver design for direct steam production, by using numerical methods, with a variable longitudinally and transversely income solar power profile. With this propose, the receiver’s geometry has been divided using the finite difference method, and the energy balance equations have been solved. Once the equations system has been solved, the receiver´s temperature distribution is known, and you can analyze the results as well as calculate other interesting data.

Optical characterisation of semi-transparent PV modules for building integration

A complete characterisation of PV modules for building integration is needed in order to know their influence on the building’s global energy balance. Specifically, certain characteristic parameters should be obtained for each different PV module suitable for building integrated photovoltaics (BIPV), some by direct or indirect measurements at the laboratory, and others by monitoring the element performance mounted in real operating conditions. In the case of transparent building envelopes it is particularly important to perform an optical and thermal characterization of the PV modules that would be integrated in them. This paper addresses the optical characterization of some commercial thin-film PV modules having different degrees of transparency, suitable for building integration in façades. The approach is based on the measurement of the spectral UV/Vis/NIR reflectance and transmittance of the different considered samples, both at normal incidence and as a function of the angle of incidence. With the obtained results, the total and zoned UV, visible and NIR transmission and reflection values are calculated, enabling the correct characterization of the PV modules integrated in façades and the subsequent evaluation of their impact over the electrical, thermal and lighting performance in a building.

Reproductive and nutritional management on ovarian response and embryo quality on rabbit does

Rabbit does in modern rabbitries are under intensive reproductive rhythms. Females are high milk producers with high energetic expenses due to the extensive overlap between lactation and gestation. This situation leads to a negative energy balance with a mobilization of body fat especially in primiparous rabbit does. Poor body condition and poor health status severely affect the reproductive features (fertility rate and lifespan of the doe as well as ovarian physiology). This paper reviews some reproductive and nutritional approaches used in the last years to improve the reproductive performance of rabbit females, mainly focusing on the influence on ovarian response and embryo quality and with emphasis on epigenetic modifications in pre-implantation embryos and offspring consequences.

Testing of crop Models for Accurate Predictions of Evapotranspiration and crop Water Use

All crop models, whether site-specific or global-gridded and regardless of crop, simulate daily crop transpiration and soil evaporation during the crop life cycle, resulting in seasonal crop water use. Modelers use several methods for predicting daily potential evapotranspiration (ET), including FAO-56, Penman-Monteith, Priestley-Taylor, Hargreaves, full energy balance, and transpiration water efficiency. They use extinction equations to partition energy to soil evaporation or transpiration, depending on leaf area index. Most models simulate soil water balance and soil-root water supply for transpiration, and limit transpiration if water uptake is insufficient, and thereafter reduce dry matter production. Comparisons among multiple crop and global gridded models in the Agricultural Model Intercomparison and Improvement Project (AgMIP) show surprisingly large differences in simulated ET and crop water use for the same climatic conditions. Model intercomparisons alone are not enough to know which approaches are correct. There is an urgent need to test these models against field-observed data on ET and crop water use. It is important to test various ET modules/equations in a model platform where other aspects such as soil water balance and rooting are held constant, to avoid compensation caused by other parts of models. The CSM-CROPGRO model in DSSAT already has ET equations for Priestley-Taylor, Penman-FAO-24, Penman-Monteith-FAO-56, and an hourly energy balance approach. In this work, we added transpiration-efficiency modules to DSSAT and AgMaize models and tested the various ET equations against available data on ET, soil water balance, and season-long crop water use of soybean, fababean, maize, and other crops where runoff and deep percolation were known or zero. The different ET modules created considerable differences in predicted ET, growth, and yield.