Effects of lanthanum modification on dielectric properties of Pb(Zr-0.90,Ti-0.10)O-3 ceramics: enhanced antiferroelectric stability

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of pH variations in a cycling model on the properties of restorative materials

This study evaluated the effect of cycling various pH demineralizing solutions on the surface hardness, fluoride release and surface properties of restorative materials (Ketac-Fil Plus, Vitremer, Fuji II LC, Freedom and Fluorofil). Thirty specimens of each material were made and the surface hardness measured. The specimens were randomized into five groups according to the pH (4.3; 4.6; 5.0; 5.5 and 6.2) of the demineralizing solution. The specimens were submitted to pH-cycling for 15 days. The specimens remained in the demineralizing solution for six hours and in the remineralizing solution for 18 hours. Then, the surface hardness (SH) was remeasured and the surface properties were assessed. Fluoride release was determined daily. Data from SH and the percentage of alteration in surface hardness were analyzed by analysis of variance (p < 0.05); the Kruskal-Wallis test was performed for the fluoride release results. When hardness was compared, the variation in pH led to a positive correlation for glass ionomer cements and a negative correlation for fluoride release. For polyacid-modified resin composites, a negative correlation was found with regards to fluoride release; no significant correlation was observed for hardness. Surface properties were influenced: an acidic pH led to a greater alteration, except for polyacid-modified resin composites. The pH of the demineralizing solution influenced fluoride release from the tested materials. The pH variation altered hardness and surface properties of glass ionomer cements but did not influence polyacid-modified resin composites.

Osteoconductive Properties of beta-Tricalcium Phosphate Matrix, Polylactic and Polyglycolic Acid Gel, and Calcium Phosphate Cement in Bone Defects

Extensive bone defects in maxillofacial region can be corrected with autogenous grafts; otherwise, the disadvantages of the therapeutics modality take the research for new bone substitutes. The aim of the study was to evaluate and compare the osteoconductive properties of 3 commercial available biomaterials. A total of 30 calvarial defects (5-mm diameter) were randomly divided into 5 treatment groups, with a total of 6 defects per treatment group (n = 6). The treatment groups were as follows: 500 to 1000 Km beta-tricalcium phosphate (beta-TCP), polylactic and polyglycolic acid (PL/PG) gel, calcium phosphate cement, untreated control, and autograft control. The evaluations were based on histomorphometric analysis at 60 postoperative days. The results have shown that beta-TCP and autograft control supported bone formation at 60 postoperative days. beta-Tricalcium phosphate showed the highest amount of mineralized area per total area and statistically significant compared with PL/PG, calcium phosphate cement, and untreated control groups. The PL/PG gel does not have osteoconductive properties and performed similar to empty control. Calcium phosphate cement showed higher number of multinucleated giant cells around the sites of the biomaterial and showed newly formed bone only at the edges of the biomaterial, without bone formation within the biomaterial. The findings presented herein indicate that bone formation reached a maximum level when rat calvarial defects were filled with beta-TCP at 60 postoperative days. Further studies should be conducted with beta-TCP to understand the potential of this biomaterial in bone regeneration.

Laurdan Spectrum Decomposition as a Tool for the Analysis of Surface Bilayer Structure and Polarity: a Study with DMPG, Peptides and Cholesterol

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of pectinolitic enzymes on the physical properties of caja-manga (Spondias cytherea Sonn.) pulp

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Properties of a biosurfactant produced by Bacillus pumilus using vinasse and waste frying oil as alternative carbon sources

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effect of enzymatic hydrolysis on some physicochemical properties of root and tuber granular starches

A hidrólise enzimática do amido pode fornecer informações importantes sobre sua estrutura granular. Amidos de mandioca, batata-doce, mandioquinha-salsa e batata foram hidrolisados por α-amilase bacteriana a 37 °C durante 48 horas, e algumas propriedades físico-químicas dos resíduos da hidrólise foram determinadas. O amido de mandioca foi o mais suscetível à enzima com 20,9% de hidrólise, enquanto o amido de batata foi o mais resistente com 5,9%. O tamanho médio dos grânulos variou de 10,8 a 23,4 μm para os amidos de mandioquinha-salsa e batata, respectivamente. Amidos de mandioca e batata-doce apresentaram um padrão de difração de raio-X tipo A, enquanto os amidos de mandioquinha-salsa e batata mostraram padrão tipo B. Todos os amidos nativos mostraram superfície granular lisa e, após hidrólise, os amidos de mandioca, batata-doce e mandioquinha-salsa mostraram alguns grânulos bastante degradados, enquanto o amido de batata apresentou sutil sinal de degradação. O teor de amilose dos amidos diminuiu com a hidrólise para os amidos de mandioca, batata-doce e mandioquinha-salsa, permanecendo inalterado para o amido de batata. Como esperado, a viscosidade intrínseca e as propriedades de pasta diminuíram para todos os amidos hidrolisados. Não houve diferença significativa entre as propriedades térmicas dos amidos nativos e hidrolisados. Estes resultados sugeriram que a hidrólise ocorreu nas áreas cristalinas e amorfas dos grânulos. O padrão de difração do tipo B e o grande tamanho dos grânulos do amido de batata podem ter contribuído para a maior resistência deste amido à hidrólise.

Effect of the addition of silanated silica on the mechanical properties of microwave heat-cured acrylic resin

Effect of the addition of silanated silica on the mechanical properties of microwave heat-cured acrylic resinObjectives: The purpose of this study was to evaluate the flexural strength and Vickers hardness of a microwave energy heat-cured acrylic resin by adding different concentrations of silane surface-treated nanoparticle silica.Methods: Acrylic resin specimens with dimensions of 65 x 10 x 2.5 mm were formed and divided into five experimental groups (n = 10) according to the silica concentration added to the acrylic resin mass (weight %) prior to polymerisation : G1, without silica; G2, 0.1% silica; G3, 0.5% silica; G4, 1.0% silica; and G5, 5.0% silica. The specimens were submitted to a three-point flexural strength test and to the Vickers hardness test (HVN). The data obtained were statistically analysed by ANOVA and the Tukey test (alpha = 0.05).Results: Regarding flexural strength, G5 differed from the other experimental groups (G1, G2, G3 and G4) presenting the lowest mean, while G4 presented a significantly higher mean, with the exception of group G3. Regarding Vickers hardness, a decrease in values was observed, in which G1 presented the highest hardness compared with the other experimental groups.Conclusion: Incorporating surface-treated silica resulted in direct benefits in the flexural strength of the acrylic resin activated by microwave energy; however, similar results were not achieved for hardness.

Incorporation of a liquid crystal to enhance the luminescence properties of Langmuir-Blodgett films of OC1OC6-PPV

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Photoluminescence properties of PZT 52/48 synthesized by microwave hydrothermal method using PVA with template

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dielectric properties of Ca(Zr0.05Ti0.95)O-3 thin films prepared by chemical solution deposition

Ca(Zr0.05Ti0.95)O-3 (CZT) thin films were grown on Pt(1 1 1)/Ti/SiO2/Si(1 0 0) substrates by the soft chemical method. The films were deposited from spin-coating technique and annealed at 928 K for 4 h under oxygen atmosphere. CZT films present orthorhombic structure with a crack free and granular microstructure. Atomic force microscopy and field-emission scanning electron microscopy showed that CZT present grains with about 47 nm and thickness about 450 nm. Dielectric constant and dielectric loss of the films was approximately 210 at 100 kHz and 0.032 at 1 MHz. The Au/CZT/Pt capacitor shows a hysteresis loop with remnant polarization of 2.5 mu C/cm(2), and coercive field of 18 kV/cm, at an applied voltage of 6 V. The leakage current density was about 4.6 x 10(-8) A/cm(2) at 3 V. Dielectric constant-voltage curve is located at zero bias field suggesting the absence of internal electric fields. (c) 2006 Elsevier B.V. All rights reserved.

Impact of oxygen atmosphere on piezoelectric properties of CaBi2Nb2O9 thin films

CaBi2Nb2O9 (CBNO) thin films were deposited on platinum-coated silicon substrates by the polymeric precursor method, and were annealed in air and in an oxygen atmosphere. The structure, surface morphology and electrical properties of CBNO thin films have been investigated. The presence of an oxygen atmosphere during crystallization of the films affected the structure perfection and morphology, as well as ferroelectric and piezoelectric properties. A reduction in P-r and piezoelectric coefficient, an increase of V-c and displacement of the Curie point is evident in the films crystallized in an oxygen atmosphere. The impact of exposure to the oxygen atmosphere on the creation of defects caused by bismuth and oxygen vacancies between layers was also investigated by X-ray photoelectron spectroscopy. (c) 2007 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Iron Oxide Versus Fe55Pt45/Fe3O4: Improved Magnetic Properties of Core/Shell Nanoparticles for Biomedical Applications

In this paper, synthesis of the Fe55Pt45/Fe3O4 core/shell structured nanoparticles using the modified polyol process combined with the seed-mediated growth method is reported. Iron oxide shell thickness was tuned controlling the Fe(acac)(3)/FePt seeds in the reaction medium. Annealing of the core/shell structure leads to iron-rich layer formation around the hard FePt phase in the nanoparticle core. However, the 2 nm Fe3O4 shell thickness seems to be the limit to obtain the enhanced magnetization close to the alpha-Fe and preserving an iron oxide shell after annealing at 500 degrees C for 30 min in a reducing atmosphere. The presence of both the oxide layer on nanoparticle surface and an intermediate iron-rich FePt layer after annealing promote strong decreases in the coercive field of the 2-nm-oxide shell thickness. These annealed nanoparticles were functionalized with dextran, presenting the enhanced characteristics for biomedical applications such as higher magnetization, very low coercivity, and a slightly iron oxide passivated layer, which leads an easy functionalization and decreases the nanoparticle toxicity.

Dependence of annealing time on structural and morphological properties of Ca(Zr0.05Ti0.95)O-3 thin films

Ca(Zr0.05Ti0.95)O-3 (CZT) thin films were prepared by the polymeric precursor method by spin-coating process. The films were deposited on Pt(1 1 1)/Ti/SiO2/Si(1 0 0) substrates and annealed at 650 degrees C for 2,4, and 6 It in oxygen atmosphere. Structure and morphology of the CZT thin films were characterized by the X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), atomic force microscopy (AFM) and field-emission scanning electron microscopy (FEG-SEM). XRD revealed that the film is free of secondary phases and crystallizes in the orthorhombic structure. The annealing time influences the grain size, lattices parameter and in the film thickness. (c) 2006 Elsevier B.V. All rights reserved.

Radio luminescence properties of decaoctahedral BaZrO3

Radioluminescence (RL) emissions were obtained for the BaZrO3 self-assembled nanocrystals under decaoctahedral shape, if produced via microwave-assisted hydrothermal method. Trapped F centers created within the band gap are the result of order-disorder effects, which act as key factors supporting significant RL emission through a detrapping process. The influences of size and morphology on RL properties are take into account. No radiation damage or loss of emission intensity was observed. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.