In situ control of Si(100) and Ge(100) surface preparation for the heteroepitaxy of III-V solar cell architectures

Si(100) and Ge(100) substrates essential for subsequent III-V integration were studied in the hydrogen ambient of a metalorganic vapor phase epitaxy reactor. Reflectance anisotropy spectroscopy (RAS) enabled us to distinguish characteristic configurations of vicinal Si(100) in situ: covered with oxide, cleaned by thermal removing in H2, and terminated with monohydrides when cooling in H2 ambient. RAS measurements during cooling in H2 ambient after the oxide removal process revealed a transition from the clean to the monohydride terminated Si(100) surface dependent on process temperature. For vicinal Ge(100) we observed a characteristic RA spectrum after annealing and cooling in H2 ambient. According to results from X-ray photo electron spectroscopy and Fourier-transform infrared spectroscopy the spectrum corresponds to the monohydride terminated Ge(100) surface.

Open-atmosphere structural depth profiling of multilayer samples of photovoltaic interest using laser-induced plasma spectrometry

The present work aims to assess Laser-Induced Plasma Spectrometry (LIPS) as a tool for the characterization of photovoltaic materials. Despite being a well-established technique with applications to many scientific and industrial fields, so far LIPS is little known to the photovoltaic scientific community. The technique allows the rapid characterization of layered samples without sample preparation, in open atmosphere and in real time. In this paper, we assess LIPS ability for the determination of elements that are difficult to analyze by other broadly used techniques, or for producing analytical information from very low-concentration elements. The results of the LIPS characterization of two different samples are presented: 1) a 90 nm, Al-doped ZnO layer deposited on a Si substrate by RF sputtering and 2) a Te-doped GaInP layer grown on GaAs by Metalorganic Vapor Phase Epitaxy. For both cases, the depth profile of the constituent and dopant elements is reported along with details of the experimental setup and the optimization of key parameters. It is remarkable that the longest time of analysis was ∼10 s, what, in conjunction with the other characteristics mentioned, makes of LIPS an appealing technique for rapid screening or quality control whether at the lab or at the production line.

Intermediate Band to Conduction Band optical absorption in ZnTe:O

ZnTe doped with high concentrations of oxygen has been proposed in previous works as intermediate band (IB) material for photovoltaic applications. The existence of extra optical transitions related to the presence of an IB has already been demonstrated in this material and it has been possible to measure the absorption coefficient of the transitions from the valence band (VB) to the IB. In this work we present the first measurement of the absorption coefficient associated to transitions from the IB to the conduction band (CB) in ZnTe:O. The samples used are 4 ?m thick ZnTe layers with or without O in a concentration ~ 1019 cm-3, which have been grown on semi-insulating GaAs substrates by molecular beam epitaxy (MBE). The IB-CB absorption coefficient peaks for photon energies ~ 0.4 eV. It is extracted from reflectance and transmittance spectra measured using Fourier Transform Infrared (FTIR) spectroscopy. Under typical FTIR measurement conditions (low light intensity, broadband spectrum) the absorption coefficient in IB-to-CB transitions reaches 700 cm-1. This is much weaker than the one observed for VB-IB absorption. This result is consistent with the fact that the IB is expected to be nearly empty of electrons under equilibrium conditions in ZnTe(:O). The absorption for VB to IB transitions is also observed in the same samples through reflectance measurements performed in the visible range using a monochromator. These measurements are compared with the quantum efficiency (QE) from solar cells fabricated under similar conditions.

Modelización de los Procesos de Cristalización en Poliolefinas

“Por lo tanto, la cristalización de polímeros se supone, y en las teorías se describe a menudo, como un proceso de múltiples pasos con muchos aspectos físico-químicos y estructurales influyendo en él. Debido a la propia estructura de la cadena, es fácil entender que un proceso que es termodinámicamente forzado a aumentar su ordenamiento local, se vea obstaculizado geométricamente y, por tanto, no puede conducirse a un estado de equilibrio final. Como resultado, se forman habitualmente estructuras de no equilibrio con diferentes características dependiendo de la temperatura, presión, cizallamiento y otros parámetros físico-químicos del sistema”. Estas palabras, pronunciadas recientemente por el profesor Bernhard Wunderlich, uno de los mas relevantes fisico-quimicos que han abordado en las ultimas décadas el estudio del estado físico de las macromoléculas, adelantan lo que de alguna manera se explicita en esta memoria y constituyen el “leitmotiv” de este trabajo de tesis. El mecanismo de la cristalización de polímeros esta aun bajo debate en la comunidad de la física de polímeros y la mayoría de los abordajes experimentales se explican a través de la teoría LH. Esta teoría clásica debida a Lauritzen y Hoffman (LH), y que es una generalización de la teoría de cristalización de una molécula pequeña desde la fase de vapor, describe satisfactoriamente muchas observaciones experimentales aunque esta lejos de explicar el complejo fenómeno de la cristalización de polímeros. De hecho, la formulación original de esta teoría en el National Bureau of Standards, a comienzos de la década de los 70, sufrió varias reformulaciones importantes a lo largo de la década de los 80, buscando su adaptación a los hallazgos experimentales. Así nació el régimen III de cristalización que posibilita la creacion de nichos moleculares en la superficie y que dio pie al paradigma ofrecido por Sadler y col., para justificar los experimentos que se obtenian por “scattering” de neutrones y otras técnicas como la técnica de “droplets” o enfriamiento rapido. Por encima de todo, el gran éxito de la teoría radica en que explica la dependencia inversa entre el tamaño del plegado molecular y el subenfriamiento, definido este ultimo como el intervalo de temperatura que media entre la temperatura de equilibrio y la temperatura de cristalización. El problema concreto que aborda esta tesis es el estudio de los procesos de ordenamiento de poliolefinas con distinto grado de ramificacion mediante simulaciones numéricas. Los copolimeros estudiados en esta tesis se consideran materiales modelo de gran homogeneidad molecular desde el punto de vista de la distribución de tamaños y de ramificaciones en la cadena polimérica. Se eligieron estas poliolefinas debido al gran interes experimental en conocer el cambio en las propiedades fisicas de los materiales dependiendo del tipo y cantidad de comonomero utilizado. Además, son modelos sobre los que existen una ingente cantidad de información experimental, que es algo que preocupa siempre al crear una realidad virtual como es la simulación. La experiencia en el grupo Biophym es que los resultados de simulación deben de tener siempre un correlato mas o menos próximo experimental y ese argumento se maneja a lo largo de esta memoria. Empíricamente, se conoce muy bien que las propiedades físicas de las poliolefinas, en suma dependen del tipo y de la cantidad de ramificaciones que presenta el material polimérico. Sin embargo, tal como se ha explicado no existen modelos teóricos adecuados que expliquen los mecanismos subyacentes de los efectos de las ramas. La memoria de este trabajo es amplia por la complejidad del tema. Se inicia con una extensa introducción sobre los conceptos básicos de una macromolecula que son relevantes para entender el contenido del resto de la memoria. Se definen los conceptos de macromolecula flexible, distribuciones y momentos, y su comportamiento en disolución y fundido con los correspondientes parametros caracteristicos. Se pone especial énfasis en el concepto de “entanglement” o enmaranamiento por considerarse clave a la hora de tratar macromoléculas con una longitud superior a la longitud critica de enmaranamiento. Finaliza esta introducción con una reseña sobre el estado del arte en la simulación de los procesos de cristalización. En un segundo capitulo del trabajo se expone detalladamente la metodología usada en cada grupo de casos. En el primer capitulo de resultados, se discuten los estudios de simulación en disolución diluida para sistemas lineales y ramificados de cadena única. Este caso mas simple depende claramente del potencial de torsión elegido tal como se discute a lo largo del texto. La formación de los núcleos “babys” propuestos por Muthukumar parece que son consecuencia del potencial de torsión, ya que este facilita los estados de torsión mas estables. Así que se propone el análisis de otros potenciales que son igualmente utilizados y los resultados obtenidos sobre la cristalización, discutidos en consecuencia. Seguidamente, en un segundo capitulo de resultados se estudian moleculas de alcanos de cadena larga lineales y ramificados en un fundido por simulaciones atomisticas como un modelo de polietileno. Los resultados atomisticos pese a ser de gran detalle no logran captar en su totalidad los efectos experimentales que se observan en los fundidos subenfriados en su etapa previa al estado ordenado. Por esta razon se discuten en los capítulos 3 y 4 de resultados sistemas de cadenas cortas y largas utilizando dos modelos de grano grueso (CG-PVA y CG-PE). El modelo CG-PE se desarrollo durante la tesis. El uso de modelos de grano grueso garantiza una mayor eficiencia computacional con respecto a los modelos atomísticos y son suficientes para mostrar los fenómenos a la escala relevante para la cristalización. En todos estos estudios mencionados se sigue la evolución de los procesos de ordenamiento y de fusión en simulaciones de relajación isoterma y no isoterma. Como resultado de los modelos de simulación, se han evaluado distintas propiedades fisicas como la longitud de segmento ordenado, la cristalinidad, temperaturas de fusion/cristalizacion, etc., lo que permite una comparación con los resultados experimentales. Se demuestra claramente que los sistemas ramificados retrasan y dificultan el orden de la cadena polimérica y por tanto, las regiones cristalinas ordenadas decrecen al crecer las ramas. Como una conclusión general parece mostrarse una tendencia a la formación de estructuras localmente ordenadas que crecen como bloques para completar el espacio de cristalización que puede alcanzarse a una temperatura y a una escala de tiempo determinada. Finalmente hay que señalar que los efectos observados, estan en concordancia con otros resultados tanto teoricos/simulacion como experimentales discutidos a lo largo de esta memoria. Su resumen se muestra en un capitulo de conclusiones y líneas futuras de investigación que se abren como consecuencia de esta memoria. Hay que mencionar que el ritmo de investigación se ha acentuado notablemente en el ultimo ano de trabajo, en parte debido a las ventajas notables obtenidas por el uso de la metodología de grano grueso que pese a ser muy importante para esta memoria no repercute fácilmente en trabajos publicables. Todo ello justifica que gran parte de los resultados esten en fase de publicación. Abstract “Polymer crystallization is therefore assumed, and in theories often described, to be a multi step process with many influencing aspects. Because of the chain structure, it is easy to understand that a process which is thermodynamically forced to increase local ordering but is geometrically hindered cannot proceed into a final equilibrium state. As a result, nonequilibrium structures with different characteristics are usually formed, which depend on temperature, pressure, shearing and other parameters”. These words, recently written by Professor Bernhard Wunderlich, one of the most prominent researchers in polymer physics, put somehow in value the "leitmotiv "of this thesis. The crystallization mechanism of polymers is still under debate in the physics community and most of the experimental findings are still explained by invoking the LH theory. This classical theory, which was initially formulated by Lauritzen and Hoffman (LH), is indeed a generalization of the crystallization theory for small molecules from the vapor phase. Even though it describes satisfactorily many experimental observations, it is far from explaining the complex phenomenon of polymer crystallization. This theory was firstly devised in the early 70s at the National Bureau of Standards. It was successively reformulated along the 80s to fit the experimental findings. Thus, the crystallization regime III was introduced into the theory in order to explain the results found in neutron scattering, droplet or quenching experiments. This concept defines the roughness of the crystallization surface leading to the paradigm proposed by Sadler et al. The great success of this theory is the ability to explain the inverse dependence of the molecular folding size on the supercooling, the latter defined as the temperature interval between the equilibrium temperature and the crystallization temperature. The main scope of this thesis is the study of ordering processes in polyolefins with different degree of branching by using computer simulations. The copolymers studied along this work are considered materials of high molecular homogeneity, from the point of view of both size and branching distributions of the polymer chain. These polyolefins were selected due to the great interest to understand their structure– property relationships. It is important to note that there is a vast amount of experimental data concerning these materials, which is essential to create a virtual reality as is the simulation. The Biophym research group has a wide experience in the correlation between simulation data and experimental results, being this idea highly alive along this work. Empirically, it is well-known that the physical properties of the polyolefins depend on the type and amount of branches presented in the polymeric material. However, there are not suitable models to explain the underlying mechanisms associated to branching. This report is extensive due to the complexity of the topic under study. It begins with a general introduction to the basics concepts of macromolecular physics. This chapter is relevant to understand the content of the present document. Some concepts are defined along this section, among others the flexibility of macromolecules, size distributions and moments, and the behavior in solution and melt along with their corresponding characteristic parameters. Special emphasis is placed on the concept of "entanglement" which is a key item when dealing with macromolecules having a molecular size greater than the critical entanglement length. The introduction finishes with a review of the state of art on the simulation of crystallization processes. The second chapter of the thesis describes, in detail, the computational methodology used in each study. In the first results section, we discuss the simulation studies in dilute solution for linear and short chain branched single chain models. The simplest case is clearly dependent on the selected torsion potential as it is discussed throughout the text. For example, the formation of baby nuclei proposed by Mutukhumar seems to result from the effects of the torsion potential. Thus, we propose the analysis of other torsion potentials that are also used by other research groups. The results obtained on crystallization processes are accordingly discussed. Then, in a second results section, we study linear and branched long-chain alkane molecules in a melt by atomistic simulations as a polyethylene-like model. In spite of the great detail given by atomistic simulations, they are not able to fully capture the experimental facts observed in supercooled melts, in particular the pre-ordered states. For this reason, we discuss short and long chains systems using two coarse-grained models (CG-PVA and CG-PE) in section 3 and 4 of chapter 2. The CG-PE model was developed during the thesis. The use of coarse-grained models ensures greater computational efficiency with respect to atomistic models and is enough to show the relevant scale phenomena for crystallization. In all the analysis we follow the evolution of the ordering and melting processes by both isothermal and non isothermal simulations. During this thesis we have obtained different physical properties such as stem length, crystallinity, melting/crystallization temperatures, and so on. We show that branches in the chains cause a delay in the crystallization and hinder the ordering of the polymer chain. Therefore, crystalline regions decrease in size as branching increases. As a general conclusion, it seems that there is a tendency in the macromolecular systems to form ordered structures, which can grown locally as blocks, occupying the crystallization space at a given temperature and time scale. Finally it should be noted that the observed effects are consistent with both, other theoretical/simulation and experimental results. The summary is provided in the conclusions chapter along with future research lines that open as result of this report. It should be mentioned that the research work has speeded up markedly in the last year, in part because of the remarkable benefits obtained by the use of coarse-grained methodology that despite being very important for this thesis work, is not easily publishable by itself. All this justify that most of the results are still in the publication phase.

Estudios termodinámicos de los procesos de vitrificación en la crioconservación de germoplasma vegetal=Thermodynamic studies of vitrification processes in plant germplasm cryopreservation

En la actualidad, las técnicas de crioconservación poseen una importancia creciente para el almacenamiento a largo plazo de germoplasma vegetal. En las dos últimas décadas, estos métodos experimentaron un gran desarrollo y se han elaborado protocolos adecuados a diferentes sistemas vegetales, utilizando diversas estrategias como la vitrificación, la encapsulación-desecación con cuentas de alginato y el método de “droplet”-vitrificación. La presente tesis doctoral tiene como objetivo aumentar el conocimiento sobre los procesos implicados en los distintos pasos de un protocolo de crioconservación, en relación con el estado del agua presente en los tejidos y sus cambios, abordado mediante diversas técnicas biofísicas, principalmente calorimetría diferencial de barrido (DSC) y microscopía electrónica de barrido a baja temperatura (crio-SEM). En un primer estudio sobre estos métodos de crioconservación, se describen las fases de enfriamiento hasta la temperatura del nitrógeno líquido y de calentamiento hasta temperatura ambiente, al final del periodo de almacenamiento, que son críticas para la supervivencia del material crioconservado. Tanto enfriamiento como calentamiento deben ser realizados lo más rápidamente posible pues, aunque los bajos contenidos en agua logrados en etapas previas de los protocolos reducen significativamente las probabilidades de formación de hielo, éstas no son del todo nulas. En ese contexto, se analiza también la influencia de las velocidades de enfriamiento y calentamiento de las soluciones de crioconservación de plantas en sus parámetros termofísicos referente a la vitrificación, en relación su composición y concentración de compuestos. Estas soluciones son empleadas en la mayor parte de los protocolos actualmente utilizados para la crioconservación de material vegetal. Además, se estudia la influencia de otros factores que pueden determinar la estabilidad del material vitrificado, tales como en envejecimiento del vidrio. Se ha llevado a cabo una investigación experimental en el empleo del crio-SEM como una herramienta para visualizar el estado vítreo de las células y tejidos sometidos a los procesos de crioconservación. Se ha comparado con la más conocida técnica de calorimetría diferencial de barrido, obteniéndose resultados muy concordantes y complementarios. Se exploró también por estas técnicas el efecto sobre tejidos vegetales de la adaptación a bajas temperaturas y de la deshidratación inducida por los diferentes tratamientos utilizados en los protocolos. Este estudio permite observar la evolución biofísica de los sistemas en el proceso de crioconservación. Por último, se estudió la aplicación de películas de quitosano en las cuentas de alginato utilizadas en el protocolo de encapsulación. No se observaron cambios significativos en su comportamiento frente a la deshidratación, en sus parámetros calorimétricos y en la superficie de las cuentas. Su aplicación puede conferir propiedades adicionales prometedoras. ABSTRACT Currently, cryopreservation techniques have a growing importance for long term plant germplasm storage. These methods have undergone great progress during the last two decades, and adequate protocols for different plant systems have been developed, making use of diverse strategies, such as vitrification, encapsulation-dehydration with alginate beads and the dropletvitrification method. This PhD thesis has the goal of increasing the knowledge on the processes underlying the different steps of cryopreservation protocols, in relation with the state of water on tissues and its changes, approached through diverse biophysical techniques, especially differential scanning calorimetry (DSC) and low-temperature scanning electron microscopy (cryo-SEM). The processes of cooling to liquid nitrogen temperature and warming to room temperature, at the end of the storage period, critical for the survival of the cryopreserved material, are described in a first study on these cryopreservation methods. Both cooling and warming must be carried out as quickly as possible because, although the low water content achieved during previous protocol steps significantly reduces ice formation probability, it does not completely disappear. Within this context, the influence of plant vitrification solutions cooling and warming rate on their vitrification related thermophysical parameters is also analyzed, in relation to its composition and component concentration. These solutions are used in most of the currently employed plant material cryopreservation protocols. Additionally, the influence of other factors determining the stability of vitrified material is studied, such as glass aging. An experimental research work has been carried out on the use of cryo-SEM as a tool for visualizing the glassy state in cells and tissues, submitted to cryopreservation processes. It has been compared with the better known differential scanning calorimetry technique, and results in good agreement and complementary have been obtained. The effect on plant tissues of adaptation to low temperature and of the dehydration induced by the different treatments used in the protocols was explored also by these techniques. This study allows observation of the system biophysical evolution in the cryopreservation process. Lastly, the potential use of an additional chitosan film over the alginate beads used in encapsulation protocols was examined. No significant changes could be observed in its dehydration and calorimetric behavior, as well as in its surface aspect; its application for conferring additional properties to gel beads is promising.

Pulsating emission of droplets from an electrified meniscus.

A numerical description is given for the pulsating emission of droplets from an electrified meniscus of an inviscid liquid of infinite electrical conductivity which is injected at a constant flow rate into a region of uniform, continuous or time periodic, electric field. Under a continuous field, the meniscus attains a periodic regime in which bursts of tiny droplets are emitted from its tip. At low electric fields this regime consists of sequences of emission bursts interspersed with sequences of meniscus oscillations without droplet emission, while at higher fields the bursts occur periodically. These results are in qualitative agreement with experimental results in the literature. Under a time periodic electric field with square waveform, the electric stress that acts on the surface of the liquid while the field is on may generate a tip that emits tiny droplets or may accelerate part of the meniscus and lead to a second emission mode in which a few large droplets are emitted after the electric field is turned off. Conditions under which each emission mode or a combination of the two are realized are discussed for low frequency oscillatory fields. A simplified model is proposed for high electric field frequencies, of the order of the capillary frequency of the meniscus. This model allows computing the average emission rate as a function of the amplitude, duration and bias of the electric field square wave, and shows that droplet emission fails to follow the applied field above a certain frequency

Optical in situ monitoring of hydrogen desorption from Ge(100) surfaces

Molecular hydrogen strongly interacts with vicinal Ge(100) surfaces during preparation in a metal organic vapor phase epitaxy reactor. According to X-ray photoemission spectroscopy and Fourier-transform infrared spectroscopy results, we identify two characteristic reflection anisotropy (RA) spectra for H-free and monohydride-terminated vicinal Ge(100) surfaces. RAS allows in situ monitoring of the surface termination and enables spectroscopic hydrogen kinetic desorption studies on the Ge(100) surface. Comparison of evaluated values for the activation energy and the pre-exponential factor of H desorption evaluated at different photon energies reflects that H unevenly affects the shape of the RA spectrum.

Multi-fluid Eulerian model of an electrospray in a host gas.

An Eulerian multifluid model is used to describe the evolution of an electrospray plume and the flow induced in the surrounding gas by the drag of the electrically charged spray droplets in the space between an injection electrode containing the electrospray source and a collector electrode. The spray is driven by the voltage applied between the two electrodes. Numerical computations and order-of-magnitude estimates for a quiescent gas show that the droplets begin to fly back toward the injection electrode at a certain critical value of the flux of droplets in the spray, which depends very much on the electrical conditions at the injection electrode. As the flux is increased toward its critical value, the electric field induced by the charge of the droplets partially balances the field due to the applied voltage in the vicinity of the injection electrode, leading to a spray that rapidly broadens at a distance from its origin of the order of the stopping distance at which the droplets lose their initial momentum and the effect of their inertia becomes negligible. The axial component of the electric field first changes sign in this region, causing the fly back. The flow induced in the gas significantly changes this picture in the conditions of typical experiments. A gas plume is induced by the drag of the droplets whose entrainment makes the radius of the spray away from the injection electrode smaller than in a quiescent gas, and convects the droplets across the region of negative axial electric field that appears around the origin of the spray when the flux of droplets is increased. This suppresses fly back and allows much higher fluxes to be reached than are possible in a quiescent gas. The limit of large droplet-to-gas mass ratio is discussed. Migration of satellite droplets to the shroud of the spray is reproduced by the Eulerian model, but this process is also affected by the motion of the gas. The gas flow preferentially pushes satellite droplets from the shroud to the core of the spray when the effect of the inertia of the droplets becomes negligible, and thus opposes the well-established electrostatic/inertial mechanism of segregation and may end up concentrating satellite droplets in an intermediate radial region of the spray.

In situ control of the GE(100)surface domain structure for III-V multijunction solar cells

Vicinal Ge(100) is the common substrate for state of the art multi-junction solar cells grown by metal-organic vapor phase epitaxy (MOVPE). While triple junction solar cells based on Ge(100) present efficiencies mayor que 40%, little is known about the microscopic III-V/Ge(100) nucleation and its interface formation. A suitable Ge(100) surface preparation prior to heteroepitaxy is crucial to achieve low defect densities in the III-V epilayers. Formation of single domain surfaces with double layer steps is required to avoid anti-phase domains in the III-V films. The step formation processes in MOVPE environment strongly depends on the major process parameters such as substrate temperature, H2 partial pressure, group V precursors [1], and reactor conditions. Detailed investigation of these processes on the Ge(100) surface by ultrahigh vacuum (UHV) based standard surface science tools are complicated due to the presence of H2 process gas. However, in situ surface characterization by reflection anisotropy spectroscopy (RAS) allowed us to study the MOVPE preparation of Ge(100) surfaces directly in dependence on the relevant process parameters [2, 3, 4]. A contamination free MOVPE to UHV transfer system [5] enabled correlation of the RA spectra to results from UHV-based surface science tools. In this paper, we established the characteristic RA spectra of vicinal Ge(100) surfaces terminated with monohydrides, arsenic and phosphorous. RAS enabled in situ control of oxide removal, H2 interaction and domain formation during MOVPE preparation.

Sheath vaporization of a monodisperse fuel-spray jet

The group vaporization of a monodisperse fuel-spray jet discharging into a hot coflowing gaseous stream is investigated for steady flow by numerical and asymptotic methods with a two-continua formulation used for the description of the gas and liquid phases. The jet is assumed to be slender and laminar, as occurs when the Reynolds number is moderately large, so that the boundary-layer form of the conservation equations can be employed in the analysis. Two dimensionless parameters are found to control the flow structure, namely the spray dilution parameter 1, defined as the mass of liquid fuel per unit mass of gas in the spray stream, and the group vaporization parameter e, defined as the ratio of the characteristic time of spray evolution due to droplet vaporization to the characteristic diffusion time across the jet. It is observed that, for the small values of e often encountered in applications, vaporization occurs only in a thin layer separating the spray from the outer droplet-free stream. This regime of sheath vaporization, which is controlled by heat conduction, is amenable to a simplified asymptotic description, independent of ε,in which the location of the vaporization layer is determined numerically as a free boundary in a parabolic problem involving matching of the separate solutions in the external streams, with appropriate jump conditions obtained from analysis of the quasi-steady vaporization front. Separate consideration of dilute and dense sprays, corresponding, respectively, to the asymptotic limits λ<<1 and λ>>1, enables simplified descriptions to be obtained for the different flow variables, including explicit analytic expressions for the spray penetration distance.

Dynamics of thermal ignition of spray flames in mixing layers

Conditions are identified under which analyses of laminar mixing layers can shed light on aspects of turbulent spray combustion. With this in mind, laminar spray-combustion models are formulated for both non-premixed and partially premixed systems. The laminar mixing layer separating a hot-air stream from a monodisperse spray carried by either an inert gas or air is investigated numerically and analytically in an effort to increase understanding of the ignition process leading to stabilization of high-speed spray combustion. The problem is formulated in an Eulerian framework, with the conservation equations written in the boundary-layer approximation and with a one-step Arrhenius model adopted for the chemistry description. The numerical integrations unveil two different types of ignition behaviour depending on the fuel availability in the reaction kernel, which in turn depends on the rates of droplet vaporization and fuel-vapour diffusion. When sufficient fuel is available near the hot boundary, as occurs when the thermochemical properties of heptane are employed for the fuel in the integrations, combustion is established through a precipitous temperature increase at a well-defined thermal-runaway location, a phenomenon that is amenable to a theoretical analysis based on activation-energy asymptotics, presented here, following earlier ideas developed in describing unsteady gaseous ignition in mixing layers. By way of contrast, when the amount of fuel vapour reaching the hot boundary is small, as is observed in the computations employing the thermochemical properties of methanol, the incipient chemical reaction gives rise to a slowly developing lean deflagration that consumes the available fuel as it propagates across the mixing layer towards the spray. The flame structure that develops downstream from the ignition point depends on the fuel considered and also on the spray carrier gas, with fuel sprays carried by air displaying either a lean deflagration bounding a region of distributed reaction or a distinct double-flame structure with a rich premixed flame on the spray side and a diffusion flame on the air side. Results are calculated for the distributions of mixture fraction and scalar dissipation rate across the mixing layer that reveal complexities that serve to identify differences between spray-flamelet and gaseous-flamelet problems.

Source terms for calculations of vaporizing and burning fuel sprays with non-unity Lewis numbers in gases with temperature-dependent thermal conductivities

Liquid-fueled burners are used in a number of propulsion devices ranging from internal combustion engines to gas turbines. The structure of spray flames is quite complex and involves a wide range of time and spatial scales in both premixed and non-premixed modes (Williams 1965; Luo et al. 2011). A number of spray-combustion regimes can be observed experimentally in canonical scenarios of practical relevance such as counterflow diffusion flames (Li 1997), as sketched in figure 1, and for which different microscalemodelling strategies are needed. In this study, source terms for the conservation equations are calculated for heating, vaporizing and burning sprays in the single-droplet combustion regime. The present analysis provides extended formulation for source terms, which include non-unity Lewis numbers and variable thermal conductivities.

Flamelet structures in spray ignition

In typical liquid-fueled burners the fuel is injected as a high-velocity liquid jet that breaks up to form the spray. The initial heating and vaporization of the liquid fuel rely on the relatively large temperatures of the sourrounding gas, which may include hot combustion products and preheated air. The heat exchange between the liquid and the gas phases is enhanced by droplet dispersion arising from the turbulent motion. Chemical reaction takes place once molecular mixing between the fuel vapor and the oxidizer has occurred in mixing layers separating the spray flow from the hot air stream. Since in most applications the injection velocities are much larger than the premixed-flame propagation velocity, combustion stabilization relies on autoignition of the fuel-oxygen mixture, with the combustion stand-off distance being controlled by the interaction of turbulent transport, droplet heating and vaporization, and gas-phase chemical reactions. In this study, conditions are identified under which analyses of laminar flamelets canshed light on aspects of turbulent spray ignition. This study extends earlier fundamental work by Liñan & Crespo (1976) on ignition in gaseous mixing layers to ignition of sprays. Studies of laminar mixing layers have been found to be instrumental in developing un-derstanding of turbulent combustion (Peters 2000), including the ignition of turbulent gaseous diffusion flames (Mastorakos 2009). For the spray problem at hand, the configuration selected, shown in Figure 1, involves a coflow mixing layer formed between a stream of hot air moving at velocity UA and a monodisperse spray moving at velocity USUA. The boundary-layer approximation will be used below to describe the resulting sl ender flow, which exhibits different igniting behaviors depending on the characteristics of t he fuel. In this approximation, consideration of the case U A = U S enables laminar ignition distances to be related to ignition times of unstrained spray flamelets, thereby pro viding quantitative information of direct applicability in regions of low scala r dissipation-rate in turbulent reactive flows (see the discussion in pp. 181–186 of Peters (2000)) . This report is organized as follows. Effects of droplet dispersion dynamics on ignition of sprays in turbulent mixing layers are discussed in Section 2. The formulation f or ignition in laminar mixing layers is outlined in Sections 3 and 4. The results are presented in Section 5. In Section 6, the mixture-fraction field and associated scalar dissipat ion rates for spray ignition are discussed. Finally, some brief conclusions are drawn in Section 7.

Análisis y simulación numérica de problemas electrohidrodinámicos relacionados con el electrospray

La presente tesis es un estudio analítico y numérico del electrospray. En la configuración más sencilla, un caudal constante del líquido a atomizar, que debe tener una cierta conductividad eléctrica, se inyecta en un medio dieléctrico (un gas u otro líquido inmiscible con el primero) a través de un tubo capilar metálico. Entre este tubo y un electrodo lejano se aplica un voltaje continuo que origina un campo eléctrico en el líquido conductor y en el espacio que lo rodea. El campo eléctrico induce una corriente eléctrica en el líquido, que acumula carga en su superficie, y da lugar a un esfuerzo eléctrico sobre la superficie, que tiende a alargarla en la dirección del campo eléctrico. El líquido forma un menisco en el extremo del tubo capilar cuando el campo eléctrico es suficientemente intenso y el caudal suficientemente pequeño. Las variaciones de presión y los esfuerzos viscosos asociados al movimiento del líquido son despreciables en la mayor parte de este menisco, siendo dominantes los esfuerzos eléctrico y de tensión superficial que actúan sobre la superficie del líquido. En el modo de funcionamiento llamado de conochorro, el balance de estos esfuerzos hace que el menisco adopte una forma cónica (el cono de Taylor) en una región intermedia entre el extremo del tubo y la punta del menisco. La velocidad del líquido aumenta al acercarse al vértice del cono, lo cual propicia que las variaciones de la presión en el líquido generadas por la inercia o por la viscosidad entren en juego, desequilibrando el balance de esfuerzos mencionado antes. Como consecuencia, del vértice del cono sale un delgado chorro de líquido, que transporta la carga eléctrica que se acumula en la superficie. La acción del campo eléctrico tangente a la superficie sobre esta carga origina una tracción eléctrica que tiende a alargar el chorro. Esta tracción no es relevante en el menisco, donde el campo eléctrico tangente a la superficie es muy pequeño, pero se hace importante en el chorro, donde es la causa del movimiento del líquido. Lejos del cono, el chorro puede o bien desarrollar una inestabilidad asimétrica que lo transforma en una espiral (whipping) o bien romperse en un spray de gotas prácticamente monodispersas cargadas eléctricamente. La corriente eléctrica transportada por el líquido es la suma de la corriente de conducción en el interior del líquido y la corriente debida a la convección de la carga acumulada en su superficie. La primera domina en el menisco y la segunda en el chorro lejano, mientras que las dos son comparables en una región intermedia de transferencia de corriente situada al comienzo del chorro aunque aguas abajo de la región de transición cono-chorro, en la que el menisco deja de ser un cono de Taylor. Para un campo exterior dado, la acumulación de carga eléctrica en la superficie del líquido reduce el campo eléctrico en el interior del mismo, que llega a anularse cuando la carga alcanza un estado final de equilibrio. El tiempo característico de este proceso es el tiempo de relajación dieléctrica, que es una propiedad del líquido. Cuando el tiempo de residencia del líquido en la región de transición cono-chorro (o en otra región del campo fluido) es grande frente al tiempo de relajación dieléctrica, la carga superficial sigue una sucesión de estados de equilibrio y apantalla al líquido del campo exterior. Cuando esta condición deja de cumplirse, aparecen efectos de relajación de carga, que se traducen en que el campo exterior penetra en el líquido, a no ser que su constante dieléctrica sea muy alta, en cuyo caso el campo inducido por la carga de polarización evita la entrada del campo exterior en el menisco y en una cierta región del chorro. La carga eléctrica en equilibrio en la superficie de un menisco cónico intensifica el campo eléctrico y determina su variación espacial hasta distancias aguas abajo del menisco del orden de su tamaño. Este campo, calculado por Taylor, es independiente del voltaje aplicado, por lo que las condiciones locales del flujo y el valor de la corriente eléctrica son también independientes del voltaje en tanto los tamaños de las regiones que determinan estas propiedades sean pequeños frente al tamaño del menisco. Los resultados experimentales publicados en la literatura muestran que existe un caudal mínimo para el que el modo cono-chorro que acabamos de describir deja de existir. El valor medio y la desviación típica de la distribución de tamaños de las gotas generadas por un electrospray son mínimos cuando se opera cerca del caudal mínimo. A pesar de que los mecanismos responsables del caudal mínimo han sido muy estudiados, no hay aún una teoría completa del mismo, si bien su existencia parece estar ligada a la aparición de efectos de relajación de carga en la región de transición cono-chorro. En esta tesis, se presentan estimaciones de orden de magnitud, algunas existentes y otras nuevas, que muestran los balances dominantes responsables de las distintas regiones de la estructura asintótica de la solución en varios casos de interés. Cuando la inercia del líquido juega un papel en la transición cono-chorro, los resultados muestran que la región de transferencia de corriente, donde la mayor parte de la corriente pasa a la superficie, está en el chorro aguas abajo de la región de transición cono-chorro. Los efectos de relajación de carga aparecen de forma simultánea en el chorro y la región de transición cuando el caudal se disminuye hasta valores de un cierto orden. Para caudales aún menores, los efectos de relajación de carga se notan en el menisco, en una región grande comparada con la de transición cono-chorro. Cuando el efecto de las fuerzas de viscosidad es dominante en la región de transición, la región de transferencia de corriente está en el chorro pero muy próxima a la región de transición cono-chorro. Al ir disminuyendo el caudal, los efectos de relajación de carga aparecen progresivamente en el chorro, en la región de transición y por último en el menisco. Cuando el caudal es mucho mayor que el mínimo del modo cono-chorro, el menisco deja de ser cónico. El campo eléctrico debido al voltaje aplicado domina en la región de transferencia de corriente, y tanto la corriente eléctrica como el tamaño de las diferentes regiones del problema pasan a depender del voltaje aplicado. Como resultado de esta dependencia, el plano caudal-voltaje se divide en diferentes regiones que se analizan separadamente. Para caudales suficientemente grandes, la inercia del líquido termina dominando frente a las fuerzas de la viscosidad. Estos resultados teóricos se han validado con simulaciones numéricas. Para ello se ha formulado un modelo simplificado del flujo, el campo eléctrico y el transporte de carga en el menisco y el chorro del electrospray. El movimiento del líquido se supone casi unidireccional y se describe usando la aproximación de Cosserat para un chorro esbelto. Esta aproximación, ampliamente usada en la literatura, permite simular con relativa facilidad múltiples casos y cubrir amplios rangos de valores de los parámetros reteniendo los efectos de la viscosidad y la inercia del líquido. Los campos eléctricos dentro y fuera del liquido están acoplados y se calculan sin simplificación alguna usando un método de elementos de contorno. La solución estacionaria del problema se calcula mediante un método iterativo. Para explorar el espacio de los parámetros, se comienza calculando una solución para valores fijos de las propiedades del líquido, el voltaje aplicado y el caudal. A continuación, se usa un método de continuación que permite delinear la frontera del dominio de existencia del modo cono-chorro, donde el método iterativo deja de converger. Cuando el efecto de la inercia del líquido domina en la región de transición cono-chorro, el caudal mínimo para el cual el método iterativo deja de converger es del orden del valor estimado del caudal para el que comienza a haber efectos de relajación de carga en el chorro y el cono. Aunque las simulaciones no convergen por debajo de dicho caudal, el valor de la corriente eléctrica para valores del caudal ligeramente mayores parece ajustarse a las estimaciones para caudales menores, reflejando un posible cambio en los balances aplicables. Por el contrario, cuando las fuerzas viscosas dominan en la región de transición, se pueden obtener soluciones estacionarias para caudales bastante menores que aquel para el que aparecen efectos de relajación de carga en la región de transición cono-chorro. Los resultados numéricos obtenidos para estos pequeños caudales se ajustan perfectamente a las estimaciones de orden de magnitud que se describen en la memoria. Por último, se incluyen como anexos dos estudios teóricos que han surgido de forma natural durante el desarrollo de la tesis. El primero hace referencia a la singularidad en el campo eléctrico que aparece en la línea de contacto entre el líquido y el tubo capilar en la mayoría de las simulaciones. Primero se estudia en qué situaciones el campo eléctrico tiende a infinito en la línea de contacto. Después, se comprueba que dicha singularidad no supone un fallo en la descripción del problema y que además no afecta a la solución lejos de la línea de contacto. También se analiza si los esfuerzos eléctricos infinitamente grandes a los que da lugar dicha singularidad pueden ser compensados por el resto de esfuerzos que actúan en la superficie del líquido. El segundo estudio busca determinar el tamaño de la región de apantallamiento en un chorro de líquido dieléctrico sin carga superficial. En esta región, el campo exterior es compensado parcialmente por el campo que induce la carga de polarización en la superficie del líquido, de forma que en el interior del líquido el campo eléctrico es mucho menor que en el exterior. Una región como ésta aparece en las estimaciones cuando los efectos de relajación de carga son importantes en la región de transferencia de corriente en el chorro. ABSTRACT This aim of this dissertation is a theoretical and numerical analysis of an electrospray. In its most simple configuration, a constant flow rate of the liquid to be atomized, which has to be an electrical conductor, is injected into a dielectric medium (a gas or another inmiscible fluid) through a metallic capillary tube. A constant voltage is applied between this tube and a distant electrode that produces an electric field in the liquid and the surrounding medium. This electric field induces an electric current in the liquid that accumulates charge at its surface and leads to electric stresses that stretch the surface in the direction of the electric field. A meniscus appears on the end of the capillary tube when the electric field is sufficiently high and the flow rate is small. Pressure variations and viscous stresses due to the motion of the liquid are negligible in most of the meniscus, where normal electric and surface tension stresses acting on the surface are dominant. In the so-called cone-jet mode, the balance of these stresses forces the surface to adopt a conical shape -Taylor cone- in a intermediate region between the end of the tube and the tip of the meniscus. When approaching the cone apex, the velocity of the liquid increases and leads to pressure variations that eventually disturb the balance of surfaces tension and electric stresses. A thin jet emerges then from the tip of the meniscus that transports the charge accumulated at its surface. The electric field tangent to the surface of the jet acts on this charge and continuously stretches the jet. This electric force is negligible in the meniscus, where the component of the electric field tangent to the surface is small, but becomes very important in the jet. Far from the cone, the jet can either develop an asymmetrical instability named “whipping”, whereby the jet winds into a spiral, or break into a spray of small, nearly monodisperse, charged droplets. The electric current transported by the liquid has two components, the conduction current in the bulk of the liquid and the convection current due to the transport of the surface charge by the flow. The first component dominates in the meniscus, the second one in the far jet, and both are comparable in a current transfer region located in the jet downstream of the cone-jet transition region where the meniscus ceases to be a Taylor cone. Given an external electric field, the charge that accumulates at the surface of the liquid reduces the electric field inside the liquid, until an equilibrium is reached in which the electric field induced by the surface charge counters the external electric field and shields the liquid from this field. The characteristic time of this process is the electric relaxation time, which is a property of the liquid. When the residence time of the liquid in the cone-jet transition region (or in other region of the flow) is greater than the electric relaxation time, the surface charge follows a succession of equilibrium states and continuously shield the liquid from the external field. When this condition is not satisfied, charge relaxation effects appear and the external field penetrates into the liquid unless the liquid permittivity is large. For very polar liquids, the field due to the polarization charge at the surface prevents the external field from entering the liquid in the cone and in certain region of the jet. The charge at the surface of a conical meniscus intensifies the electric field around the cone, determining its spatial variation up to distances downstream of the apex of the order of the size of the meniscus. This electric field, first computed by Taylor, is independent of the applied voltage. Therefore local flow characteristics and the electric current carried by the jet are also independent of the applied voltage provided the size of the regions that determine these magnitudes are small compared with the size of the meniscus. Many experiments in the literature show the existence of a minimum flow rate below which the cone-jet mode cannot be established. The mean value and the standard deviation of the electrospray droplet size distribution are minimum when the device is operated near the minimum flow rate. There is no complete explanation of the minimum flow rate, even though possible mechanisms have been extensively studied. The existence of a minimum flow rate seems to be connected with the appearance of charge relaxation effects in the transition region. In this dissertation, order of magnitude estimations are worked out that show the dominant balances in the different regions of the asymptotic structure of the solution for different conditions of interest. When the inertia of the liquid plays a role in the cone-jet transition region, the region where most of the electric current is transfered to the surface lies in the jet downstream the cone-jet transition region. When the flow rate decreases to a certain value, charge relaxation effects appear simultaneously in the jet and in the transition region. For smaller values of the flow rate, charge relaxation effects are important in a region of the meniscus larger than the transition region. When viscous forces dominate in the flow in the cone-jet transition region, the current transfer region is located in the jet immediately after the transition region. When flow rate is decreased, charge relaxation effects appears gradually, first in the jet, then in the transition region, and finally in the meniscus. When flow rate is much larger than the cone-jet mode minimum, the meniscus ceases to be a cone. The electric current and the structure of the solution begin to depend on the applied voltage. The flow rate-voltage plane splits into different regions that are analyzed separately. For sufficiently large flow rates, the effect of the inertia of the liquid always becomes greater than the effect of the viscous forces. A set of numerical simulations have been carried out in order to validate the theoretical results. A simplified model of the problem has been devised to compute the flow, the electric field and the surface charge in the meniscus and the jet of an electrospray. The motion of the liquid is assumed to be quasi-unidirectional and described by Cosserat’s approximation for a slender jet. This widely used approximation allows to easily compute multiple configurations and to explore wide ranges of values of the governing parameters, retaining the effects of the viscosity and the inertia of the liquid. Electric fields inside and outside the liquid are coupled and are computed without any simplification using a boundary elements method. The stationary solution of the problem is obtained by means of an iterative method. To explore the parameter space, a solution is first computed for a set of values of the liquid properties, the flow rate and the applied voltage, an then a continuation method is used to find the boundaries of the cone-jet mode domain of existence, where the iterative method ceases to converge. When the inertia of the liquid dominates in the cone-jet transition region, the iterative method ceases to converge for values of the flow rate for which order-of-magnitude estimates first predict charge relaxation effects to be important in the cone and the jet. The electric current computed for values of the flow rate slightly above the minimum for which convergence is obtained seems to agree with estimates worked out for lower flow rates. When viscous forces dominate in the transition region, stationary solutions can be obtained for flow rates significantly smaller than the one for which charge relaxation effects first appear in the transition region. Numerical results obtained for those small values of the flow rate agree with our order of magnitude estimates. Theoretical analyses of two issues that have arisen naturally during the thesis are summarized in two appendices. The first appendix contains a study of the singularity of the electric field that most of the simulations show at the contact line between the liquid and the capillary tube. The electric field near the contact line is analyzed to determine the ranges of geometrical configurations and liquid permittivity where a singularity appears. Further estimates show that this singularity does not entail a failure in the description of the problem and does not affect the solution far from the contact line. The infinite electric stresses that appear at the contact line can be effectively balanced by surface tension. The second appendix contains an analysis of the size and slenderness of the shielded region of a dielectric liquid in the absence of free surface charge. In this region, the external electric field is partially offset by the polarization charge so that the inner electric field is much lower than the outer one. A similar region appears in the estimates when charge relaxation effects are important in the current transfer region.

Research on wide-bandgap intermediate band solar cells and development of experimental techniques for their characterization

El trabajo que ha dado lugar a esta Tesis Doctoral se enmarca en la invesitagación en células solares de banda intermedia (IBSCs, por sus siglas en inglés). Se trata de un nuevo concepto de célula solar que ofrece la posibilidad de alcanzar altas eficiencias de conversión fotovoltaica. Hasta ahora, se han demostrado de manera experimental los fundamentos de operación de las IBSCs; sin embargo, esto tan sólo has sido posible en condicines de baja temperatura. El concepto de banda intermedia (IB, por sus siglas en inglés) exige que haya desacoplamiento térmico entre la IB y las bandas de valencia y conducción (VB and CB, respectivamente, por sus siglas en inglés). Los materiales de IB actuales presentan un acoplamiento térmico demasiado fuerte entre la IB y una de las otras dos bandas, lo cual impide el correcto funcionamiento de las IBSCs a temperatura ambiente. En el caso particular de las IBSCs fabricadas con puntos cuánticos (QDs, por sus siglas en inglés) de InAs/GaAs - a día de hoy, la tecnología de IBSC más estudiada - , se produce un rápido intercambio de portadores entre la IB y la CB, por dos motivos: (1) una banda prohibida estrecha (< 0.2 eV) entre la IB y la CB, E^, y (2) la existencia de niveles electrónicos entre ellas. El motivo (1) implica, a su vez, que la máxima eficiencia alcanzable en estos dispositivos es inferior al límite teórico de la IBSC ideal, en la cual E^ = 0.71 eV. En este contexto, nuestro trabajo se centra en el estudio de IBSCs de alto gap (o banda prohibida) fabricadsas con QDs, o lo que es lo mismo, QD-IBSCs de alto gap. Hemos fabricado e investigado experimentalmente los primeros prototipos de QD-IBSC en los que se utiliza AlGaAs o InGaP para albergar QDs de InAs. En ellos demostramos une distribución de gaps mejorada con respecto al caso de InAs/GaAs. En concreto, hemos medido valores de E^ mayores que 0.4 eV. En los prototipos de InAs/AlGaAs, este incremento de E^ viene acompaado de un incremento, en más de 100 meV, de la energía de activación del escape térmico. Además, nuestros dispositivos de InAs/AlGaAs demuestran conversión a la alza de tensión; es decir, la producción de una tensión de circuito abierto mayor que la energía de los fotones (dividida por la carga del electrón) de un haz monocromático incidente, así como la preservación del voltaje a temperaura ambiente bajo iluminación de luz blanca concentrada. Asimismo, analizamos el potencial para detección infrarroja de los materiales de IB. Presentamos un nuevo concepto de fotodetector de infrarrojos, basado en la IB, que hemos llamado: fotodetector de infrarrojos activado ópticamente (OTIP, por sus siglas en inglés). Nuestro novedoso dispositivo se basa en un nuevo pricipio físico que permite que la detección de luz infrarroja sea conmutable (ON y OFF) mediante iluminación externa. Hemos fabricado un OTIP basado en QDs de InAs/AlGaAs con el que demostramos fotodetección, bajo incidencia normal, en el rango 2-6/xm, activada ópticamente por un diodoe emisor de luz de 590 nm. El estudio teórico del mecanismo de detección asistido por la IB en el OTIP nos lleva a poner en cuestión la asunción de quasi-niveles de Fermi planos en la zona de carga del espacio de una célula solar. Apoyados por simuaciones a nivel de dispositivo, demostramos y explicamos por qué esta asunción no es válida en condiciones de corto-circuito e iluminación. También llevamos a cabo estudios experimentales en QD-IBSCs de InAs/AlGaAs con la finalidad de ampliar el conocimiento sobre algunos aspectos de estos dispositivos que no han sido tratados aun. En particular, analizamos el impacto que tiene el uso de capas de disminución de campo (FDLs, por sus siglas en inglés), demostrando su eficiencia para evitar el escape por túnel de portadores desde el QD al material anfitrión. Analizamos la relación existente entre el escape por túnel y la preservación del voltaje, y proponemos las medidas de eficiencia cuántica en función de la tensión como una herramienta útil para evaluar la limitación del voltaje relacionada con el túnel en QD-IBSCs. Además, realizamos medidas de luminiscencia en función de la temperatura en muestras de InAs/GaAs y verificamos que los resltados obtenidos están en coherencia con la separación de los quasi-niveles de Fermi de la IB y la CB a baja temperatura. Con objeto de contribuir a la capacidad de fabricación y caracterización del Instituto de Energía Solar de la Universidad Politécnica de Madrid (IES-UPM), hemos participado en la instalación y puesta en marcha de un reactor de epitaxia de haz molecular (MBE, por sus siglas en inglés) y el desarrollo de un equipo de caracterización de foto y electroluminiscencia. Utilizando dicho reactor MBE, hemos crecido, y posteriormente caracterizado, la primera QD-IBSC enteramente fabricada en el IES-UPM. ABSTRACT The constituent work of this Thesis is framed in the research on intermediate band solar cells (IBSCs). This concept offers the possibility of achieving devices with high photovoltaic-conversion efficiency. Up to now, the fundamentals of operation of IBSCs have been demonstrated experimentally; however, this has only been possible at low temperatures. The intermediate band (IB) concept demands thermal decoupling between the IB and the valence and conduction bands. Stateof- the-art IB materials exhibit a too strong thermal coupling between the IB and one of the other two bands, which prevents the proper operation of IBSCs at room temperature. In the particular case of InAs/GaAs quantum-dot (QD) IBSCs - as of today, the most widely studied IBSC technology - , there exist fast thermal carrier exchange between the IB and the conduction band (CB), for two reasons: (1) a narrow (< 0.2 eV) energy gap between the IB and the CB, EL, and (2) the existence of multiple electronic levels between them. Reason (1) also implies that maximum achievable efficiency is below the theoretical limit for the ideal IBSC, in which EL = 0.71 eV. In this context, our work focuses on the study of wide-bandgap QD-IBSCs. We have fabricated and experimentally investigated the first QD-IBSC prototypes in which AlGaAs or InGaP is the host material for the InAs QDs. We demonstrate an improved bandgap distribution, compared to the InAs/GaAs case, in our wide-bandgap devices. In particular, we have measured values of EL higher than 0.4 eV. In the case of the AlGaAs prototypes, the increase in EL comes with an increase of more than 100 meV of the activation energy of the thermal carrier escape. In addition, in our InAs/AlGaAs devices, we demonstrate voltage up-conversion; i. e., the production of an open-circuit voltage larger than the photon energy (divided by the electron charge) of the incident monochromatic beam, and the achievement of voltage preservation at room temperature under concentrated white-light illumination. We also analyze the potential of an IB material for infrared detection. We present a IB-based new concept of infrared photodetector that we have called the optically triggered infrared photodetector (OTIP). Our novel device is based on a new physical principle that allows the detection of infrared light to be switched ON and OFF by means of an external light. We have fabricated an OTIP based on InAs/AlGaAs QDs with which we demonstrate normal incidence photodetection in the 2-6 /xm range optically triggered by a 590 nm light-emitting diode. The theoretical study of the IB-assisted detection mechanism in the OTIP leads us to questioning the assumption of flat quasi-Fermi levels in the space-charge region of a solar cell. Based on device simulations, we prove and explain why this assumption is not valid under short-circuit and illumination conditions. We perform new experimental studies on InAs/GaAs QD-IBSC prototypes in order to gain knowledge on yet unexplored aspects of the performance of these devices. Specifically, we analyze the impact of the use of field-damping layers, and demonstrate this technique to be efficient for avoiding tunnel carrier escape from the QDs to the host material. We analyze the relationship between tunnel escape and voltage preservation, and propose voltage-dependent quantum efficiency measurements as an useful technique for assessing the tunneling-related limitation to the voltage preservation of QD-IBSC prototypes. Moreover, we perform temperature-dependent luminescence studies on InAs/GaAs samples and verify that the results are consistent with a split of the quasi-Fermi levels for the CB and the IB at low temperature. In order to contribute to the fabrication and characterization capabilities of the Solar Energy Institute of the Universidad Polite´cnica de Madrid (IES-UPM), we have participated in the installation and start-up of an molecular beam epitaxy (MBE) reactor and the development of a photo and electroluminescence characterization set-up. Using the MBE reactor, we have manufactured and characterized the first QD-IBSC fully fabricated at the IES-UPM.