From point defects to plate tectonic faults

Understanding and explaining emergent constitutive laws in the multi-scale evolution from point defects, dislocations and two-dimensional defects to plate tectonic scales is an arduous challenge in condensed matter physics. The Earth appears to be the only planet known to have developed stable plate tectonics as a means to get rid of its heat. The emergence of plate tectonics out of mantle convection appears to rely intrinsically on the capacity to form extremely weak faults in the top 100 km of the planet. These faults have a memory of at least several hundred millions of years, yet they appear to rely on the effects of water on line defects. This important phenomenon was first discovered in laboratory and dubbed ``hydrolytic weakening''. At the large scale it explains cycles of co-located resurgence of plate generation and consumption (the Wilson cycle), but the exact physics underlying the process itself and the enormous spanning of scales still remains unclear. We present an attempt to use the multi-scale non-equilibrium thermodynamic energy evolution inside the deforming lithosphere to move phenomenological laws to laws derived from basic scaling quantities, develop self-consistent weakening laws at lithospheric scale and give a fully coupled deformation-weakening constitutive framework. At meso- to plate scale we encounter in a stepwise manner three basic domains governed by the diffusion/reaction time scales of grain growth, thermal diffusion and finally water mobility through point defects in the crystalline lattice. The latter process governs the planetary scale and controls the stability of its heat transfer mode.

Restriction of intramuscular neurite branching and extension is lost in agrin and rapsyn-deficient mice

The phrenic nerve enters the diaphragm at approximately embryonic day 12.5 (E12.5) in the mouse. The secondary nerve trunk advances along the centre of the diaphragm muscle and extends tertiary branches primarily towards the lateral side during normal embryonic development. In the present study we quantified the intramuscular neurite branching in the most ventral region of the diaphragm at E15.5 and E18.5 in wild-type mice, agrin knock-out mice (KOAG) and rapsyn knock-out mice (KORAP). KOAG and KORAP have decreased muscle contraction due to their inability to maintain/form acetylcholine receptor (AChR) clusters during embryonic development. Heterozygote mothers were anaesthetised via an overdose of Nembutal (30 mg; Boeringer Ingelheim, Ridgefield, CT, USA) and killed via cervical dislocation. There were increases in the number of branches exiting the medial side of the phrenic nerve trunk in KOAG and KORAP compared to wild-type mice, but not on the lateral side at E15.5 and E18.5. However, the number of bifurcations in the periphery significantly increased on both the medial and lateral sides of the diaphragm at E15.5 and E18.5 in KOAG and KORAP compared to control mice. Furthermore, neurites extended further on both the medial and lateral sides of the diaphragm at E15.5 and E18.5 in KOAG and KORAP compared to wild-type mice. Together these results show that the restriction of neurite extension and bifurcations from the secondary nerve trunk is lost in both KOAG and KORAP allowing us the opportunity to investigate the factors that restrict motoneuron behaviour in mammalian muscles.

The motor neurite terminal determines where neuromuscular synapses form in the absence of agrin

Agrin is a proteoglycan secreted by motor neurite terminals that functions to initiate and maintain AChR clusters at the nerve terminal. This led to the theory that neurite terminals decide where neuromuscular synapses form by secreting agrin. However, initiation of AChR clustering occurs in the absence of the innervating motoneuron and in the absence of agrin. In this instance, the muscle, not the nerve, is deciding the location of neuromuscular synapses by drawing neurite terminals towards pre-existing AChR clusters. If this were true, one would expect the initial innervation patterns to be the same in agrin-deficient mice and wild-type mice. To test this we quantified the intramuscular axonal branching and synapse formation in the diaphragm at E14.5 in agrin-deficient mice and wild-type mice. Heterozygote mothers were anaesthetised with Nembutal (30 mg) and killed via cervical dislocation. In the diaphragm, the nerve trunk runs down the centre of the muscle and extends branches primarily toward the lateral side. In agrin-deficient mice however, we found significantly more branches exited the phrenic nerve trunk, branched in the periphery and extended further on the medial side. Moreover, we found that the percentage α-bungarotoxin/synaptophysin colocalisations, markers of pre- and postsynaptic differentiation, respectively, was the same in agrin-deficient mice and wild-type mice. These results show that initial innervation patterns are not the same in agrin-deficient mice and wild-type mice indicating neurite terminals, not muscle, decide the placement of neuromuscular synapses in the absence of agrin.

CRISTIANISMO ETÍOPE A PARTIR DA EXPERIÊNCIA ÉTNICA NARRADA EM ATOS 8, 26-40

Torna-se muito importante demonstrar as experiências cristãs que existiram e coexistiram juntas ou/e imersas nas culturas extrapalestinenses e que exerceram protagonismo no anúncio do querigma. São experiências cristãs vividas e realizadas no período do cristianismo primitivo, e que, sem dúvida, contribuíram significativamente para o seu processo de expansão. Apresentamos a perícope Atos 8,26-40. Trata-se do episódio de Filipe e o Etíope. Acontece um deslocamento do eixo geográfico-missionário de Samaria ao caminho que desce de Jerusalém a Gaza , retornando a Cesaréia. O texto abre o horizonte das experiências cristãs a outros povos e nações, representadas nesta perícope pela figura do Etíope eunuco. Partindo de Atos 8,26-40, na perspectiva da redação lucana como ponto de partida, por meio dos procedimentos exegéticos e dos recursos histórico- literários, apoiado no referencial teórico dos conceitos de etnicidade e fronteiras étnicas, nós pretendemos investigar a possibilidade de uma experiência cristã vivenciada na Etiópia, que se constrói etnicamente desde as identidades que interagem na perícope e que apontam ao imaginário do universo simbólico do Etíope. Assim, resgataremos na exegese bíblica pautas hermenêuticas para a nossa prática teológico-bíblica-pastoral no horizonte das identidades e fronteiras étnicas do universo afro americano e caribenho.

Synthesis and evaluation of asperlicin analogues as non-peptidal cholecystokinin-antagonists

The SAR of Asperlicin analogues is reported, leading to bioactive 1,4-benzodiazepine-2-ones, which were prepared in a 3 step reaction sequence. The Asperlicin substructure was built up using Tryptophan and readily available 2-amino-acetophenones. This template, containing a 1,4-benzodiazepin-2-one moiety with a 3-indolmethyl side chain, was transformed into mono- and di-substituted 3-indol-3 '-yl-methyl-1,4-benzodi-azepine-2-ones by selective alkylation and acylation reactions. The SAR optimization of the 1,4-benzodiazepine scaffold has included variations at the 5-, 7-, 8-position, at the N1, N-indole nitrogen and the configuration of the C3-position. The most active Asperlicin analogue, having an IC50 of 1.6 microM on the CCKA receptor subtype, was obtained from Tryptophan in only 3 steps in an overall yield of 48%.

The role of oxidation in the protection of sliding metal surfaces

This study is concerned with the mechanisms of growth and wear of protective oxide films formed under various tribological conditions. In the study three different tribological systems are examined in each of which oxidational wear is the dominant equilibrium mode. These are an unlubricated steel on steel system sliding at low and elevated temperatures, a boundary lubricated aluminium bronze on steel system and an unlubricated reciprocating sliding 9% Cr steel system operated at elevated temperature, in an atmosphere of carbon dioxide. The results of mechanical measurements of wear and friction are presented for a range of conditions of load, speed and temper.ature for the systems, together with the results of extensive examinations of the surfaces and sub­ surfaces by various physical methods of analysis. The major part of the thesis, however, is devoted to the development and application of surface models and theoretical quantative expressions in order to explain the observed oxidational wear phenomena. In this work, the mechanisms of formation of load bearing ox ide plateaux are described and are found to be dependent on system geometry and environment. The relative importance of ''in contact" and "out of contact" oxidation is identified together with growth rate constants appropriate to the two situations. Hypotheses are presented to explain the mechanisms of removal of plateaux to form wear debris. The latter hypotheses include the effects of cyclic stressing and dislocation accumulation, together with effects associated with the kinetics of growth and physical properties of the various oxides. The proposed surf ace mode1s have led to the develop­ ment of quantitative expressions for contact temperature, unlubricated wear rates, boundary lubricated wear rates and the wear of rna ter ial during the transition from severe to mild wear. In general theoretical predictions from these expressions are in very good agreement with experimental values.

The prediction of vibration in large electric machines

This thesis reports the development of a reliable method for the prediction of response to electromagnetically induced vibration in large electric machines. The machines of primary interest are DC ship-propulsion motors but much of the work reported has broader significance. The investigation has involved work in five principal areas. (1) The development and use of dynamic substructuring methods. (2) The development of special elements to represent individual machine components. (3) Laboratory scale investigations to establish empirical values for properties which affect machine vibration levels. (4) Experiments on machines on the factory test-bed to provide data for correlation with prediction. (5) Reasoning with regard to the effect of various design features. The limiting factor in producing good models for machines in vibration is the time required for an analysis to take place. Dynamic substructuring methods were adopted early in the project to maximise the efficiency of the analysis. A review of existing substructure- representation and composite-structure assembly methods includes comments on which are most suitable for this application. In three appendices to the main volume methods are presented which were developed by the author to accelerate analyses. Despite significant advances in this area, the limiting factor in machine analyses is still time. The representation of individual machine components was addressed as another means by which the time required for an analysis could be reduced. This has resulted in the development of special elements which are more efficient than their finite-element counterparts. The laboratory scale experiments reported were undertaken to establish empirical values for the properties of three distinct features - lamination stacks, bolted-flange joints in rings and cylinders and the shimmed pole-yoke joint. These are central to the preparation of an accurate machine model. The theoretical methods are tested numerically and correlated with tests on two machines (running and static). A system has been devised with which the general electromagnetic forcing may be split into its most fundamental components. This is used to draw some conclusions about the probable effects of various design features.

The creep behaviour of pressure diecast zinc-aluminium based alloys

The creep behaviour of three pressure diecast commercial zinc-aluminium based alloys: Mazak 3, corresponding to BS 1004A, and the new alloys ZA.8 and ZA.27 with a series of alloys with compositions ranging from 0% to 30% aluminium was investigated. The total creep elongation of commercial alloys was shown to be well correlated using an empirical equation. Based on this a parametrical relationship was derived which allowed the total creep extension to be related to the applied stress, the temperature and the time of test, so that a quantitative assessment of creep of the alloys could be made under different conditions. Deviation from the normal creep kinetics occurred in alloys ZA.8 and ZA.27 at very low stresses, 150°C, due to structural coarsening combined with partial transformation of ε -phase into T' phase. The extent of primary creep was found to increase with aluminium content, but secondary creep rates decreased in the order Mazak 3, ZA.8 and ZA.27. Thus, based on the above equation, ZA.8 was found to have a substantially better total creep resistance than ZA.27, which in turn was marginally better than Mazak 3 for strains higher than 0.5%, but inferior for smaller strains, due to its higher primary creep extension. The superior creep resistance of ZA.8 was found to be due to the presence of strictly-orientated, thin plate-like precipitates of ε(CuZn4) phase in the zinc matrix of the eutectic and the lamellarly decomposed β phase, in which the precipitation morphology and orientation of ε in the zinc matrix was determined. Over broad ranges of temperature and stresses, the stress exponents and activation energies for creep were found to be consistent with some proposed creep rate mechanisms; i.e. viscous glide for Mazak 3, dislocation climb over second phase particles for ZA.8 and dislocation climb for ZA.27, controlled by diffusion in the zinc-rich phase. The morphology of aluminium and copper-rich precipitates formed from the solid solution of zinc was clearly revealed. The former were found to further increase the creep rate of inherently low creep resistant zinc, but the latter contributed significantly to the creep resistance. Excess copper in the composition, however, was not beneficial in improving the creep resistance. Decomposition of β in copper-containing alloys was found to be through a metastable Zn-Al phase which is strongly stabilised by copper, and the final products of the decomposition had a profound effect on the creep strength of the alloys. The poor creep resistance of alloy ZA.27 was due to the presence of particulate products derived from decomposed β-phase and a large volume of fine, equiaxed products of continuously decomposed α-dendrites.

The compressive creep and load relaxation properties of a series of high aluminium zinc-based alloys

A new family of commercial zinc alloys designated as ZA8, ZA12, and ZA27 and high damping capacity alloys including Cosmal and Supercosmal and aluminium alloy LM25 were investigated for compressive creep and load relaxation behaviour under a series of temperatures and stresses. A compressive creep machine was designed to test the sand cast hollow cylindrical test specimens of these alloys. For each compressive creep experiment the variation of creep strain was presented in the form of graphs plotted as percentage of creep strain () versus time in seconds (s). In all cases, the curves showed the same general form of the creep curve, i.e. a primary creep stage, followed by a linear steady-state region (secondary creep). In general, it was observed that alloy ZA8 had the least primary creep among the commercial zinc-based alloys and ZA27 the greatest. The extent of primary creep increased with aluminium content to that of ZA27 then declined to Supercosmal. The overall creep strength of ZA27 was generally less than ZA8 and ZA12 but it showed better creep strength than ZA8 and ZA12 at high temperature and high stress. In high damping capacity alloys, Supercosmal had less primary creep and longer secondary creep regions and also had the lowest minimum creep rate among all the tested alloys. LM25 exhibited almost no creep at maximum temperature and stress used in this research work. Total creep elongation was shown to be well correlated using an empirical equation. Stress exponent and activation energies were calculated and found to be consistent with the creep mechanism of dislocation climb. The primary α and β phases in the as-cast structures decomposed to lamellar phases on cooling, with some particulates at dendrite edges and grain boundaries. Further breakdown into particulate bodies occurred during creep testing, and zinc bands developed at the highest test temperature of 160°C. The results of load relaxation testing showed that initially load loss proceeded rapidly and then deminished gradually with time. Load loss increased with temperature and almost all the curves approximated to a logarithmic decay of preload with time. ZA alloys exhibited almost the same load loss at lower temperature, but at 120°C ZA27 improved its relative performance with the passage of time. High damping capacity alloys and LM25 had much better resistance to load loss than ZA alloys and LM25 was found to be the best against load loss among these alloys. A preliminary equation was derived to correlate the retained load with time and temperature.

The creep properties of a series of zinc-rich zinc-aluminium alloys

The compressive creep behaviour of six sand cast zinc-rich alloys: No3 and No5, corresponding to BS 1004A and BS 1004B, respectively, alloy No2, ILZRO,.16 and two newer alloys ACuZinc5 and ACuZinc10 was investigated. The total creep contraction of the alloys was found to be well correlated using an empirical equation. On the basis of this equation, a parametrical relationship was derived which allowed the total creep contraction to be related to the applied stress, the temperature and the time of test, so that a quantitative assessment of compressive creep of the alloys could be made under different testing conditions. The primary creep and secondary creep rates were found for the alloys at different temperatures and stresses. Generally, the primary creep contraction was found to increase with copper content, whereas secondary creep rates decreased in the order No3, ACuZinc10, ACuZinc5 and No2. ILZRO.16 was tested only at the highest stress and two higher temperatures. The results showed that ILZRO.16 had higher creep resistance than all the other alloys. Thus, based on the above empirical equation, alloy No2 was found to have a substantially better total creep resistance than alloys No3 and No5, and slightly better than ACuZinc5 and ACuZinc10 for strains up to 1%. Both ACuZinc alloys had higher creep strength than commercial alloys No3 and No5. Alloy No5 had much higher creep resistance than alloy No3 under all conditions. The superior creep resistance of alloy No2 was considered to be due to the presence of small precipitates of -phase in the zinc matrix and a regular eutectic morphology. The stress exponents and activation energies for creep under different testing conditions were found to be consistent with some established creep-controlling mechanisms; i.e. dislocation climb for alloy No3, dislocation climb over second phase particles for alloys No5, No2, ACuZinc10, controlled by lattice diffusion in the zinc-rich phase. The lower creep resistance of alloy No3 was mainly due to the lower creep strength of copper-free primary particles having greater volume than eutectic in the microstructure. Alloys No5, ACuZinc5 and ACuZinc10 showed much better creep resistance than alloy No3, based on the precipitation-hardening due to the presence of small -phase precipitates. The primary dendrites in both ACuZinc alloys however were not of much benefit in improving the creep resistance of the alloys.

La traduction des discours politiques au Canada

This work focuses on translated political speeches made by Canadas prime minister during times of national crises. Delivered orally in both English and French, this translation-based political discourse is examined in a tripartite manner, offering the reader contextualisation of the corpus researched; description of the translation shifts encountered; and interpretation of the discourse varies greatly depending on the era observed. Since the latter half of the 20th century, for instance, different text types have been assigned to different categories of translators. As for translative shifts revealed in the corpus, they have been categorised as either paratextual or textual divergences. Paratextual differences indicate that the Canadian prime ministers national statements in English and French do not necessarily seek to portray symmetry between what is presented in each language. Each version of a national speech thus retains a relative degree of visual autonomy. In sum, accumulated instances of paratextual divergence suggest an identifiable paratextual strategy, whereby translation contributes to the illusion that there is only one federal language: the readers. The deployment of this paratextual strategy obscures the fact that such federal expression occurs in two official languages. The illusion of monolingualism generates two different world views one for each linguistic community. Similarly, another strategy is discerned in the analysis of translative textual shifts a textual strategy useful in highlighting some of the power struggles inherent in translated federal expression. Textual interpretation of data identifies four federal translation tendencies: legitimisation and characterisation of linguistic communities; dislocation of the speech-event; neutralisation of (linguistic) territory; and valorisation of federalism.

Direct measurement of coherency limits for strain relaxation in heteroepitaxial core/shell nanowires

The growth of heteroepitaxially strained semiconductors at the nanoscale enables tailoring of material properties for enhanced device performance. For core/shell nanowires (NWs), theoretical predictions of the coherency limits and the implications they carry remain uncertain without proper identification of the mechanisms by which strains relax. We present here for the Ge/Si core/shell NW system the first experimental measurement of critical shell thickness for strain relaxation in a semiconductor NW heterostructure and the identification of the relaxation mechanisms. Axial and tangential strain relief is initiated by the formation of periodic a/2 〈110〉 perfect dislocations via nucleation and glide on {111} slip-planes. Glide of dislocation segments is directly confirmed by real-time in situ transmission electron microscope observations and by dislocation dynamics simulations. Further shell growth leads to roughening and grain formation which provides additional strain relief. As a consequence of core/shell strain sharing in NWs, a 16 nm radius Ge NW with a 3 nm Si shell is shown to accommodate 3% coherent strain at equilibrium, a factor of 3 increase over the 1 nm equilibrium critical thickness for planar Si/Ge heteroepitaxial growth. © 2012 American Chemical Society.

Tensile properties of as fabricated, aged, and stretched SiC whisker and particle reinforced 2009 aluminium alloy

Tensile tests were carried out using specimens of 2009 aluminium alloy reinforced by either SiC whiskers or particles. The size distributions of the whiskers and particles in the matrix were obtained by image analysis. It was found that failure was a result of uniform void nucleation and coalescence in the as fabricated composites, or a result of fast crack propagation initiated by a flaw developed at clusters of SiC in the aged or stretched and aged composites. The strengths of the as fabricated composites were estimated based on the results of image analysis using continuum mechanics and dislocation theories. The estimation indicated that the tensile strengths are largely contributed to by composite strengthening, supplemented by residual dislocation strengthening and work hardening. Owing to the flaw controlled failure, the tensile strengths of the aged or stretched and aged composites were independent of aging time, aging temperature, and the amount of stretching. The elastic moduli of the composites were estimated using the Halpin-Tsai model and a good correlation was found between the measured and estimated moduli. © 1996 The Institute of Materials.

Improvement of the mechanical properties of 2124 Al/SiCp MMC plate by optimisation of the solution treatment

Static mechanical properties of 2124 Al/SiCp MMC have been measured as a function of solution temperature and time. An optimum solution treatment has been established which produces significant improvements in static mechanical properties and fatigue crack growth resistance over conventional solution treatments. Increasing the solution treatment parameters up to the optimum values improves the mechanical properties because of intermetallic dissolution, improved solute and GPB zone strengthening and increased matrix dislocation density. Increasing the solution treatment parameters beyond the optimum values results in a rapid reduction in mechanical properties due to the formation of gas porosity and surface blisters. The optimum solution treatment improves tensile properties in the transverse orientation to a greater extent than in the longitudinal orientation and this results in reduced anisotropy. © 1996 Elsevier Science Limited.

Effects of hydrostatic tension on cleavage fracture of pure polycrystalline zinc

A study was made of notch effects on the cleavage fracture of polycrystalline zinc. It was seen that the nominal fracture stress of SENB specimens was independent of notch angle. The maximum tensile stress below the notch at fracture in SENB specimens was shown to be different from the tensile stress at fracture in tensile testpieces over a temperature range from −196 to −17°C. The notch root strain at fracture was found to be the same as the uniaxial tensile fracture strain over this temperature interval. These results were interpreted as showing the cleavage fracture of polycrystalline zinc to be shear-stress or initiation controlled, as predicted by Stroh's dislocation model of cleavage.