拼接光栅的偏差对光束空间特性的影响

用拼接小尺寸多层介质膜衍射介质膜衍射光栅的办法制作大口径的高破坏阈值光栅成为解决拍瓦激光系统输出能量的关键技术——光栅拼接技术。拼接的每个光栅都存在五维自由度的偏差，对激光脉冲的空间特性和时间特性产生影响。用夫琅禾费衍射的方法分析了拼接光栅的偏差对光束空间特性的影响，建立了偏差和远场强度分布之间的函数关系并用数值方法进行模拟，得出角度偏差对光束远场分布的影响可以忽略，而位移偏差：光栅间拼缝和前后位移偏差是影响光束远场分布的关键因素。

调Q及连续掺Yb光纤激光器中的自锁模研究

在用半导体激光器抽运的单包层掺Yb调Q光纤激光器中观察到了清晰稳定的自锁模脉冲序列。脉冲包络形状为调Q脉冲。每个锁模脉冲的幅值由其在调Q脉冲中的相应位置决定。经过分析，认为自相位调制是调Q光纤激光器中产生锁模的主要原因。自相位调制的存在使得光脉冲的频谱被展宽，当这种展宽和腔的模式间隔相差不多时，腔内的模式便能相互作用，直到它们之间产生一个固定的相位关系。也即形成锁模。在此基础上。去掉声光晶体，并用两个光栅作为腔镜，实现了全光纤法布里-珀罗(F-P)腔锁模光纤激光器。改变腔结构，分别采用光栅和光纤反射圈作为

Design and control of an ultraprecision stage used in grating tiling

In petawatt laser system, the gratings used to compose pulse compressor are very large in size which can be only acquired currently by arraying small aperture gratings to form a large one instead, an approach referred to as grating tiling. Theory and experiments have demonstrated that the coherent addition of multiple small gratings to form a larger grating is viable, the key technology of which is to control the relative position and orientation of each grating with high precision. According to the main factors that affect the performance of the grating tiling, a 5-DOF ultraprecision stage is developed for the grating tiling experiment. The mechanism is formed by serial structures. The motion of the mechanism is guided by flexure hinges and driven by piezoelectric actuators and the movement resolution of which can achieve nanometer level. To keep the stability of the mechanism, capacitive position sensors with nanometer accuracy are fixed on it to provide feedback signals with which to realize closed-loop control, thus the positioning precision of the mechanism is within several nanometers range through voltage control and digital PID algorithm. Results of experiments indicate that the performance of the mechanism can meet the requirement of precision for grating tiling.}

变栅距光栅实现啁啾脉冲光谱整形

为了充分利用放大介质的增益带宽，获得脉宽更短，功率更高的输出脉冲，需要将输入到主放大链的种子脉冲进行光谱整形来补偿放大过程中的增益窄化效应。提出了利用变栅距反射光栅实现中心波长1053nm，谱宽6nm啁啾脉冲的光谱整形。运用严格的光栅衍射耦合波理论分析光栅的衍射特性，发现该方案不会引入相位畸变。分别计算和分析了刻槽深度、入射角大小、光栅周期以及入射光波长的变化对衍射效率的影响，通过选取适当的光栅参量可获得0．5％～84％的光谱调制深度。

拼接光栅压缩器的时域特性

在拼接光栅和拼接光栅压缩器的设计中,子光栅调节偏差不可避免,各维偏差与拼接光栅的时间特性之间的关系很关键。通过脉冲压缩理论分析得到各维偏差和聚焦脉冲时间宽度展宽之间的解析关系,从数值计算结果分析,面平行左右偏差对脉冲的时间宽度影响较大,必须控制在21.08 μrad内；条纹密度差异对脉冲宽度的影响很显著,相对条纹密度的比值应控制在10-5以内；从消除角色散的角度分析,面平行俯仰偏差和条纹平行度偏差可以相互补偿,条纹密度差异和面平行左右偏差也可以相互补偿。

阵列光栅压缩器的空域特性

引入角度偏差、位移偏差作为拼接光栅系统的物理参数，定义了拼接光栅的孔径函数，利用傅里叶角谱理论研究了高斯脉冲入射拼接光栅压缩器后的远场分布特性。研究表明；出射脉冲仍然是高斯型脉冲，但包络中心发生偏移，偏移量由角度偏差量和光束口径决定；位移偏差引入的相位随着拼接光栅压缩器传递，其对远场焦斑的影响，取决于每片子光栅的非整数倍光栅常数的横向位移偏差和纵向位移偏差的综合作用。通过数值计算得到了各维偏差对阵列光栅压缩器空域特性的影响，计算表明：光栅面外角度偏差（俯仰左右）和条纹平行度偏差都必须控制在1μrad以内，

腐蚀石英光栅为分光元件的激光照明系统研究(英文)

利用腐蚀法制作的石英光栅作为分光元件，将其应用拓展到激光景观工程领域中，产生了全新的激光景观效果．给出了一种适用于室外复杂环境用于激光景观照明系统中的光栅分光原理、制作工艺过程等，发展了采用光栅分光元件产生多种不同激光景观照明效果的控制系统，并与利用高速扫描振镜实现的激光照明系统的景观效果进行了比较．

Split-aperture laser pulse compressor design tolerant to alignment and line-density differences

We introduce a four-pass laser pulse compressor design based on two grating apertures with two gratings per aperture that is tolerant to some alignment errors and, importantly, to grating-to-grating period variations. Each half-beam samples each grating in a diamond-shaped compressor that is symmetric about a central bisecting plane. For any given grating, the two half-beams impinge on opposite sides of its surface normal. It is shown that the two split beams have no pointing difference from paired gratings with different periods. Furthermore, no phase shift between half-beams is incurred as long as the planes containing a grating line and the surface normal for each grating of the pair are parallel. For grating pairs satisfying this condition, gratings surfaces need not be on the same plane, as changes in the gap between the two can compensate to bring the beams back in phase. © 2008 Optical Society of America.

Encoded cell grating array in anti-counterfeit technology

The dot matrix hologram (DMH) has been widely used in anti-counterfeiting label. With the same technology and cell array configuration, we can encode to the incidence beam. These codes can be some image matrix grating with different grating gap and different grating orientation. When the multi-level phase diffractive grating is etched, the incidence beam on the cell appears as an encoding image. When the encoded grating and DMH are used in the same label synchronously, the technology of multi-encoded grating array enhances the anti-counterfeit ability.

A wideband sensitive holographic photopolymer

A novel wideband sensitive dry holographic photopolymer sensitized by rose bengal (RB) and methylene blue (MB) is fabricated, the holographic storage characteristics of which are investigated under different exposure wavelengths. The result shows that the sensitive spectral band exceeds 200 nm in visible light range, the maximum diffraction efficiency under different exposure wavelengths is more than 40% and decreases with the decrease of exposure wavelength, the exposure sensitivity is not change with the exposure wavelength. This photopolymer is appropriate for wavelength multiplexing or multi-wavelength recording in digital holographic storage.

Riboflavin sensitized photopolymer materials for holographic storage

Riboflavin is employed as the photosensitizer of a novel photopolyrner material for holographic recording, This material has a broad absorption spectrum range (More than 200nm) due to the addition of this dye. The experimental results show that our material has high diffraction efficiency and large refractive index modulation. The maximum diffraction efficiency of the photopolymer is about 56%. The digital data pages are stored in this medium and the reconstructed data page has a good fidelity, with the bit-error-ratio of about 1.8 X 10(-4). it is found that the photopolymer material is suitable for high-density volume holographic digital storage.

一种基于衍射光栅光束质量M^2因子的实时检测技术

提出了一种新的光束质量膨因子实时检测技术，利用一个普通正交衍射光栅组将一束待测激光束分成3×3共9路光，并利用光路调整器使9路光束通过不同的光程后有序地排列在CCD相机的探测面上，并使得各路光的光程差分布在束腰附近两倍瑞利距离内，从而可利用单一CCD探测面来同时获取待测光束多个位置上的光斑图样。再利用二阶矩理论求出各个位置上的光束束宽，通过曲线拟合进而实现光束质量的实时检测。结果表明，对于连续He-Ne激光器的输出光束，采用实时检测技术得到的测量结果与用传统方法得到的结果基本一致。

Radially polarized and pulsed output from passively Q-switched Nd:YAG ceramic microchip laser

For the first time, to the best of our knowledge, a radially polarized laser pulse was produced from a passively Q-switched Nd:YAG ceramic microchip laser with a piece of Cr4+:YAG crystal as the saturable absorber and multilayer concentric subwavelength grating as the polarization-selective output coupler. The averaged laser power reached 450 mW with a slope efficiency of 30.2%. The laser pulse had a maximum peak power of 759 W, a minimum pulse duration of 86 ns, and a 6.7 kHz repetition rate at 3.7 W absorbed pump power. The polarization degree of the radially polarized pulse was measured to be as high as 97.4%. Such a radially polarized laser pulse with a high peak power and a short width is important to numerous applications such as metal cutting. (C) 2008 Optical Society of America

Investigation of optical properties of Ce3+-doped Gd2SiO5 crystal irradiated by a femtosecond laser

We report on the optical property changes for Ce3+-doped Gd2SiO5 crystal irradiated by a femtosecond (fs) laser. Absorption spectra showed that Ce-related color centers were formed in this crystal after an 800 nm fs laser irradiation. The annealing temperature-dependence of the refractive index and absorption intensity changes have been investigated. Furthermore, a new way of writing overlapped gratings inside the crystal by use of birefringence of fs laser beam in this crystal was proposed. (c) 2005 Elsevier B.V. All rights reserved.

Optical transfer of periodic microstructures by interfering femtosecond laser beams

We report on an optical interference method for transferring periodic microstructures of metal film from a supporting substrate to a receiving substrate by means of five-beam interference of femtosecond laser pulses. Scanning electron microscopy and optical microscopy revealed microstructures with micrometer-order were transferred to the receiving substrate. In the meanwhile, a negative copy of the transferred structures was induced in the metal film on the supporting substrate. The diffraction characteristics of the transferred structures were also evaluated. The present technique allows one-step realization of functional optoelectronic devices. (C) 2005 Optical Society of America.