Gravidez e radiologia: fim do mito

Dissertação para obtenção do grau de Mestre no Instituto Superior de Ciências da Saúde Egas Moniz

Caracterização física e química da pólvora

O presente trabalho consiste na caracterização física e química da pólvora. Esta caracterização foi realizada para alguns tipos de pólvora, com o objetivo de se poder empregar este tipo de material noutros âmbitos, que não seja só nas Forças Armadas, nomeadamente, no armamento. A caracterização física abrangeu, essencialmente, a caracterização morfológica das amostras tal-qual, nomeadamente, as pólvoras multi-perfurada, tubular, tubular (rocket), cilíndrica, esférica, lamelar, em fita e a pólvora negra. A técnica utilizada foi a observação através de uma lupa estereoscópica. Após a combustão, foi utilizado o microscópio eletrónico de varrimento. A caracterização química foi realizada no âmbito da análise química elementar, e também no âmbito da combustão, às condições atmosféricas. Na análise química elementar, foram estudadas a pólvora multiperfurada, tubular, tubular rocket e em fita, por intermédio da espectrometria de fluorescência de raios-X - dispersão de energia e por espectrometria de absorção atómica de chama. No âmbito da combustão, foram estudas a taxa de queima e a velocidade de propagação de chama, nas amostras de pólvora multi-perfurada e a pólvora de fita, através de técnicas de medição de massa e de visualização de chama. Na discussão de resultados constatou-se que a maioria dos tipos de pólvora estudados pertencem ao grupo dos propelentes de base dupla. Apesar da variabilidade entre amostras, verificou-se que o principal elemento comum é o chumbo. Quanto à taxa de queima, esta apresenta uma evolução aproximadamente linear em todas as amostras. Foi, ainda, apresentada uma velocidade de propagação de chama característica para os dois tipos de pólvora estudados, tendo sido estabelecida para a pólvora multi-perfurada uma velocidade SR = 1,1 mm/s, para em fita, SR = 6,0 mm/s.

ERNESTO GEISEL E A IMPRENSA DO BRASIL: A propaganda ideológica sobre o quarto Presidente do Regime Militar brasileiro (1964-1985), entre sua eleição e posse

No início da década de 1970 o Brasil viveu um período de grande crescimento econômico e de ampla divulgação das ações governamentais através dos meios de comunicação para tentar legitimar o Regime Militar. O País era governado pelo general-presidente Emílio Garrastazu Médici (1969-1974), cuja gestão ficara conhecida como os anos de chumbo . Em meados de 1973 ele decide que seu sucessor no comando da República seria o general Ernesto Geisel. O objetivo deste trabalho é investigar a campanha de propaganda ideológica feita pelas revistas Manchete e Veja e pelos jornais O Estado de S. Paulo e Folha de S. Paulo para apresentar aos seus leitores o novo Presidente. O trabalho deu-se inicialmente por meio de pesquisas bibliográficas para compreensão daquele período histórico e de analises documentais. Posteriormente realizou-se o estudo das edições selecionadas dos periódicos acima citados para buscar neles evidências dos componentes da propaganda ideológica realizada e para descobrir se eles atuaram ou não como difusores dos interesses oficiais.

Incrustação em poço produtor de petróleo e gás natural: um estudo de caso

Water and gas is a common by - product of the oil production process. Production may be compromised by the precipitation of inorganic salts in both the reservoir and producing well, through scale formation. This precipitation is likely the cause of the formation damage. High temperatures and h igh pressures (HTHP) may favor the precipitation of insoluble salts. The most common types of scale in oil fields are calcium carbonate and calcium sulphate, strontium and barium sulphate. New types of scale formation have attracted special attention such as zinc sulphide and lead. This precipitation may occur in the pores of reservoir rocks, in the production string and in equipment, causing obstructions and consequent production losses. In this study, the influence of well depth on incrustation compositio n was investigated to design removal treatments and assess the behavior of these deposits along the string, through the analysis of pressure and temperature. Scale residues were recovered from the inside of the production string of an oil and gas well duri ng the string removal operation. A total of 10 samples from different depths (15.4 m to 4061.5 m) were obtained. Initially a dissolution test was conducted in weak acid, similar to that used in removal operations with this type of scale formation. Majority composition was defined and confirmed by dissolution tests using X - Ray Fluorescence Spectroscopy (XRF), X - Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) techniques. Residues with distinct characteristics were observed in different proportion s, showing a tendency toward increased and/or decreased mass with depth. In the samples closest to the surface, typical sandstone residues were found, with calcium (45% Ca) as the metal of highest concentration. The obtained results indicate correlations o f the scale types studied with the depth and, consequently, with the thermodynamic conditions of pressure and temperature.

Metagenoma de comunidades microbianas expostas à radiação natural e a metais

Many species have specialized to live in the most varied existing environments showing the remarkable adaptability of the microbial world the most diverse physicochemical conditions. Environments exposed to natural radiation and metals are scarce around the world, presenting a microbiota still unknown. With a total number estimated between 4 and 6 x 1030 microrganisms on earth, they constitute an enormous biological and genetic pool to be explored. Metagenomic approach independent of cultivation, provides a new form to access to the potential genomic environmental samples becoming a powerful tool for the elucidation of ecological functions, metabolic profiles, as well as to identify new biomolecules. In this context, the genetic material of environmental soil and water samples from Açude Boqueirao Parelhas-RN, under the influence of natural radiation and the presence of metals, was extracted, pirosequencing and the generated sequences were analyzed by bioinformatics programs (MG-RAST and STAMP). Taxonomic comparative profiles of both samples showed high abundance of Domain Bacteria, followed by a small portion attributable to Eucaryota Domains, Archaea and Viruses. Proteobacteria, Actinobacteria and Bacterioidetes phyla showed the greater dominance in both samples. Important genera and species associated with resistance to various stressors found in region were observed. Sequences related to oxidative and heat stress, DNA replication and repair, and resistance to toxic compounds were observed, suggesting a significant relationship between the microbiota and their metabolic profile, influenced by regional environmental variables. The results of this study add valuable and unpublished data on the composition of microbial communities in these regions

Estudo da incorporação de resíduos de perfuração para aplicação em cimentação de poços de petróleo

During the drilling of oil and natural gas are generated solid waste, liquid and gaseous. These solid fragments, which are known as cuttings, are carried to the surface through the drilling fluid. Furthermore, this fluid serves to cool the bit, keeping the internal pressure of the well, and others. This solid residue is very polluting, because it has incorporated beyond the drilling fluid, which has several chemical additives harmful to the environment, some heavy metals that are harmful to the environment, such as lead. To minimize the residue generated, are currently being studied numerous techniques to mitigate the problems that such waste can cause to the environment, like addition of cuttings in the composition of soil cement brick masonry construction, addition of cuttings on the clay matrix for the manufacture of solid masonry bricks and ceramic blocks and coprocessing of the cuttings in cement. So, the main objective of this work is the incorporation of cuttings drilling of oil wells, the cement slurry used in the cementing operation of the well. This cuttings used in this study, arising from the formation Pendências, was milled and separated in a sieve of 100 mesh. After grinding had a mean particle sike in order of 86 mm and crystal structure containing phases of quartz and calcite type, characteristic of the Portland cement. Were formulated and prepared slurries of cement with density 13 lb / gal, containing different concentrations of gravel, and realized characterization tests API SPEC 10A and RP 10B. Free water tests showed values lower than 5.9% and the rheological model that best described the behavior of the mixtures was the power. The results of compressive strength (10.3 MPa) and stability (Dr <0.5 lb / gal) had values within the set of operational procedures. Thus, the gravel from the drilling operation, may be used as binders in addition to Portland cement oil wells, in order to reuse this waste and reduce the cost of the cement paste.

Aplicação da tecnologia eletroquímica para a remoção e monitoramento de metais pesados em efluentes aquosos

Heavy metals are present in industrial waste. These metals can generate a large environmental impact contaminating water, soil and plants. The chemical action of heavy metals has attracted environmental interest. In this context, this study aimed to test t he performance of electrochemical technologies for removing and quantifying heavy metals. First ly , the electroanalytical technique of stripping voltammetry with glassy carbon electrode (GC) was standardized in order to use this method for the quantificatio n of metals during their removal by electrocoagulation process (EC). A nalytical curves were evaluated to obtain reliability of the determin ation and quantification of Cd 2+ and Pb 2+ separately or in a mixture. Meanwhile , EC process was developed using an el ectrochemical cell in a continuous flow (EFC) for removing Pb 2+ and Cd 2+ . The se experiments were performed using Al parallel plates with 10 cm of diameter (  63.5 cm 2 ) . The optimization of conditions for removing Pb 2+ and Cd 2+ , dissolved in 2 L of solution at 151 L h - 1 , were studied by applying different values of current for 30 min. Cd 2+ and Pb 2+ concentrations were monitored during electrolysis using stripping voltammetry. The results showed that the removal of Pb 2 + was effective when the EC pro cess is used, obtaining removals of 98% in 30 min. This behavior is dependent on the applied current, which implies an increase in power consumption. From the results also verified that the stripping voltammetry technique is quite reliable deter mining Pb 2+ concentration , when compared with the measurements obtained by atomic absorption method (AA). In view of this, t he second objective of this study was to evaluate the removal of Cd 2+ and Pb 2+ (mixture solution) by EC . Removal efficiency increasing current was confirmed when 93% and 100% of Cd 2+ and Pb 2+ was removed after 30 min . The increase in the current promotes the oxidation of sacrificial electrodes, and consequently increased amount of coagulant, which influences the removal of heavy metals in solution. Adsortive voltammetry is a fast, reliable, economical and simple way to determine Cd 2+ and Pb 2+ during their removal. I t is more economical than those normally used, which require the use of toxic and expensive reagents. Our results demonstrated the potential use of electroanalytical techniques to monitor the course of environmental interventions. Thus, the application of the two techniques associated can be a reliable way to monitor environmental impacts due to the pollution of aquatic ecosystems by heavy metals.

Influência da radiação ionizante natural no açude do boqueirão (RN): avaliação de risco saúde/ambiente

The contamination of water bodies with toxic substances causes a decrease in water quality, representing a risk to public health. In this context, human activities are generally seen as the main sources of water degradation. However, elements found naturally in the environment can also compromise water quality. Thus, the Boqueirão‘s dam, located in the municipality of Parelhas (RN, Brazil), was chosen as area for the development of this study, as its geological region is rich in the emission of natural ionizing radiation that produces byproducts like lead and Radon. Moreover, the area has a strong human influence that enhances the risks of pollutant discharge in this body of water.Thus, the objectives of this study were centered (i) in the analysis of risk perception in the city of Parelhas (RN/Brasil) due to the use of the water from the Boqueirão Dam; and (ii) in the assessment of water quality in the Dam using methods that quantify, mainly, heavy metals and radiation levels, as well as these toxics potential of inducing mutations on genetic material. The analysis of risk perception showed that the population in the city of Parelhas can perceive a risk in using the water from the dam and that they can recognize factors that influence the water quality. Regarding the second objective, the set of data point to the contamination of the Dam by heavy metals, as well as levels of radioactive parcicles and Radon – also present in high concentrations in outdoor air and on soil. Thus, it is possible to infer that the population residing in this area is subjected to injuries caused by exposure to natural and anthropogenic contamination. Our findings corroborate with the perception of the population regarding the risks associated with the use of the Dam for several types of activities. It is expected that the information gathered in this study can substantiate activities and future researches in this semiarid region in the Rio Grande do Norte/Brazil. Also, that the set of data can enable a better understanding of the specific toxicological scenario of risk found for the population and the effect of the contamination for the biota, which aids the development of a future risk assessment and a consequent management of this local issue.

Estudo do tratamento sequencial (adsorção e eletro-oxidação) para remediação de efluente sintético contaminado com BTX

This paper proposed the study of the treatment of a synthetic wastewater contaminated with BTX by electro-oxidation batch with the anode of Ti/PbO2, and the adsorption of BTX using expanded perlite as adsorbent material, and to evaluate the best operating conditions both methods in order to perform a sequential treatment (adsorption and electro-oxidation) and achieve greater efficiency in the removal of the compounds. The operating conditions were measured: temperature, current density and applied amount of the adsorbent material, by UV-VIS analysis and Demand Chemical oxygen demand (COD). According to the experimental results, the electro-oxidative treatment was efficient in the degradation of the compounds BTX (benzene, toluene and xylenes) in synthetic sewage due to the electrochemical properties of the anode of Ti/PbO2. The applied current density and temperature promoted increased efficiency of COD removal, reaching obtain percentages greater than 70%. In the adsorption process, the temperature increase was not a factor in the removal of organic matter, while the increase in the amount of adsorbent material led to an increase in the percentage removal, obtaining 66.30% using 2 g of adsorbent. The selected operating conditions of both treatments performed separately take into account the removal efficiency of organic matter, and the low energy consumption and operating costs, so the sequential treatment were satisfactory reaching 87.26% of COD removal using adsorption as a pretreatment. Quantification of BTX through the analysis of gas chromatography at the end of the treatments also confirmed the removal efficiency of organic compounds, giving outstanding advantages to sequential treatment.

Estudo de métodos de tratamento de efluentes (troca iônica e eletroquímico) separados e sequenciais para eliminação de derivados de petróleo

The produce of waste and the amount of the water produced coming from activities of petroleum production and extraction has been a biggest challenge for oil companies with respect to environmental compliance due to toxicity. The discard or the reuse this effluent containing organic compounds as BTEX (benzene, toluene, ethylbenzene and xylene) can cause serious environmental and human health problems. Thus, the objective this paper was study the performance of two process (separately and sequential) in one synthetic effluent for the benzene, toluene and xylene removal (volatile hydrocarbons presents in the produced water) through of electrochemical treatment using Ti/Pt electrode and exchange resin ionic used in the adsorption process. The synthetic solution of BTX was prepared with concentration of 22,8 mg L-1, 9,7 mg L-1 e 9,0 mg L-1, respectively, in Na2SO4 0,1 mol L-1. The experiments was developed in batch with 0.3 L of solution at 25ºC. The electrochemical oxidation process was accomplished with a Ti/Pt electrode with different current density (J = 10, 20 e 30 mA.cm-2). In the adsorption process, we used an ionic exchange resin (Purolite MB 478), using different amounts of mass (2,5, 5 and 10 g). To verify the process of technics in the sequential treatment, was fixed the current density at 10 mA cm-2 and the resin weight was 2.5 g. Analysis of UV-VIS spectrophotometry, chemical oxygen demand (COD) and gas chromatography with selective photoionization detector (PID) and flame ionization (FID), confirmed the high efficiency in the removal of organic compounds after treatment. It was found that the electrochemical process (separate and sequential) is more efficient than absorption, reaching values of COD removal exceeding 70%, confirmed by the study of the cyclic voltammetry and polarization curves. While the adsorption (separately), the COD removal did not exceed 25,8%, due to interactions resin. However, the sequential process (electrochemical oxidation and adsorption) proved to be a suitable alternative, efficient and cost-effectiveness for the treatment of effluents petrochemical.

Estudo da eficiência dos adsorventes de Al2O3 e Fe/Al2O3 para remoção de BTX presente em água contaminada com gasolina

Contamination of groundwater by BTX has been featured in recent decades. This type of contamination is due to small and continuous leaks at gas stations, causing serious problems to public health and the environment. Based on these antecedents, the search for new alternatives for treating contaminated water is shown to be essential. Therefore, this study aimed to evaluate the efficiency of removal of BTX by adsorption processes employing commercial alumina (Al2O3) and alumina supported with iron (Fe/Al2O3) as adsorbents. It was prepared by a in a synthetic gasoline solution and distilled water to simulate an actual sample. Initially, the adsorbents were characterized by techniques XRD, TG / DTG, XRF, FTIR and SEM/EDS, several trials, where he was placed synthetic solution to react in the presence of Al2O3 and Fe/Al2O3 in a closed, mechanical stirring system were performed varying the catalyst concentration 2, 4 and 6 g.L-1 every 0, 10, 30 60, 90 and 120 min, aliquots were taken and brought to analysis by gas chromatography flame ionization with headspace extraction. The results indicated that the absorbent which has higher BTX removal capacity was the Fe/Al2O3 at a concentration of 6 g.L-1, pH = 4 and time of 90 minutes reaction, resulting in an efficiency, resulting in a 86,5% efficiency for benzene removal, for the 95,4% toluene, 90,8% for ɱ,ρ- xylene and 93.7% for the θ-xylenes. Subsequently, we performed a kinetic study of the reactions, the values of experimental adsorption capacity (qe) showed agreement with the values of the theoretical adsorption capacity (qc) to the pseudo-second-order model in the adsorption tests using 2 and 6 gL-1 of Al2O3 and assays using 2, 4 and 6 g.L-1 of Fe/Al2O3. A fact corroborated by the R2 values, thus indicating that the chemical interactions are present in the adsorption mechanisms of BTX.

Ajustes de coeficientes integrantes de processos físicos e bioquímicos na autedepuração em curso de água de médio porte

The mathematical modeling in the simulation of self-purification capacity in lotic environment is an important tool in the planning and management of hydric resources in hydrographic basin scale. It satisfactorily deals with the self-purification process when the coefficients of physical and biochemical processes are calibrated from monitorated water quality data, which was the main focus of this study. The present study was conducted to simulate the behavior of the parameters OD, BOD5, total phosphorus, E. coli, ammonia, nitrite, nitrate and the total metals cadmium, chromium, copper, lead and zinc in the Uberabinha’s lower course (with an approximate annual growth flow between 4-35 m3/s), in a stretch of 19 km downstream of the treated effluent release by the WWTP of the city. The modelings, on the present study, show the importance of constant water quality parameters monitoration over the water course, based on the comparison of the simulations from calibrated coefficients and coefficients obtained in the literature for the period of June until November 2015. After coefficients calibration, there were good adjustments between simulated and measured data for the parameters OD, BOD, Ptotal, ammonia and nitrate and unsatisfactory adjust for the parameters nitrite and E. coli. About the total metals, the adjustments were not satisfactory on the reservoir’s vicinity of the Small Hydropower Plant Martins, due the considerable increase of the bottom sediment in lentic region. The greatest scientific contribution of this study was to calibrate the decay coefficient K and the quantification of the release by the fund S of total metals in watercourse midsize WWTP pollutant load receptor, justified by the lack of studies in the literature about the subject. For the metals cadmium, chromium, copper, lead and zinc, the borderline for K and S calibrated were: 0.0 to 13.0 day-1 and 0.0 to 1.7 g/m3.day; 0.0 to 0.9 day-1 and 0.0 to 7.3 g/m3.day; 0.0 to 25.0 day-1 and 0.0 to 1.8 g/m3.day; 0.0 to 7.0 day-1 and 0.0 to 40.3 g/m3.day; 0.0 to 30.0 day-1 and 0.0 to 70.1 g/m3.day.

Assessment of metals contamination (Cd, Pb, Ni) at the Óbidos Lagoon using Cerastoderma edule as a biomonitoring tool

A poluição marinha é um problema ambiental Mundial que afeta as constituintes bióticas e abióticas do Ecossistema. Os resultados de diversas atividades antropogénicas chegam ao meio marinho através de escorrências terrestres, industriais e agrícolas assim como através de descargas domésticas, causando distúrbios neste Ecossistema. Sendo assim, a avaliação da contaminação por metais é uma das prioridades tendo em conta que estes químicos têm comportamentos acumulativos e podem ser transportados ao longo de grandes distâncias. Nos estuários, os bivalves são componentes chaves das comunidades macrobentónicas devido o seu papel vital na comunidade e também por serem uma ótima fonte de alimentação para os seres Humanos. Na Lagoa de Óbidos, uma das espécies com estas características e intensamente apanhada é o berbigão Cerastoderma edule. Este berbigão foi descrito por vários autores como sendo tolerante a diversos poluentes. Sendo assim, no presente estudo, o principal objetivo foi utilizar C. edule como ferramenta de biomonitorização de contaminações por metais na Lagoa de Óbidos, avaliando a contaminação por Cádmio, Chumbo e Níquel durante as estações do ano de 2009 e 2010 em duas estações de amostragens (estação ML e BSB). Os resultados foram complementados com a análise de contaminações por metais em amostras de águas e sedimentos. Diversas respostas fisiológicas do berbigão foram também averiguadas de modo a perceber os efeitos da presença de metais e sua acumulação. Finalmente, avaliou-se a Dose Semanal Admissível Provisória (DSAP) para o consumo de berbigão para os mínimos e máximos de concentrações de metais detetados em cada estação de amostragem. Todos os metais foram detetados em amostras de água enquanto apenas o Pb foi detetado no sedimento. O Pb e o Ni foram detetados mais vezes na amostras biológicas do que o Cd. No entanto, as contaminações por metais Pb e Cd no berbigão foram frequentemente acima do limiar fixado pelas autoridades responsáveis enquanto o Ni se encontrou perto dos valores legislados. A avaliação da DSAP revelou a necessidade de aumentar a monitorização biológica neste berbigão visto que a dose semanal admissível foi muito baixa para os três metais. De um modo geral, C. edule refletiu as modificações ambientais, respondendo a modificações físico-químicas e contaminações por metais durante o período de estudo em ambas as estações de amostragem. Assim, este estudo permitiu concluir que Cerastoderma edule foi um bom e sensível indicador de contaminações por metais, especialmente para o Pb e preferencialmente para o Ni.

Melhoria de procedimentos internos no laboratório do Instituto dos Vinhos do Douro e do Porto, I.P.

Este relatório foi elaborado no âmbito do estágio curricular realizado na Direção de Serviços Técnicos e de Certificação do Instituto dos Vinhos do Douro e do Porto, I.P. Teve como principal objetivo apresentar propostas de alteração de procedimentos internos do laboratório do Instituto dos Vinhos do Douro e do Porto, I.P., no sentido de reduzir o tempo de resposta às solicitações, procurando uma melhor rentabilização tanto de equipamentos como de recursos humanos. Para atingir tal objetivo, foi elaborado o diagnóstico da situação, com base na informação recolhida na Direção de Serviços Técnicos e de Certificação, incluindo os dados fornecidos pelo software GLAB que dá apoio às operações realizadas no laboratório do Instituto dos Vinhos do Douro e do Porto. Além disso, foi efetuado o acompanhamento do circuito das amostras de produtos vínicos desde a sua receção, à análise nos setores do laboratório e posterior validação dos resultados. Dado que o estudo da entrada de amostras no setor Análise Mineral foi maioritariamente inconclusivo, apurou-se o custo por análise na determinação do chumbo e, ainda, foi realizada uma simulação determinar a despesa necessária para reduzir o número de amostras analisadas de cada vez que se liga o equipamento. Foi ainda comparado o custo da determinação do parâmetro furfural, análise que tanto pode ser realizada no setor Cromatografia Gasosa como no setor Cromatografia Líquida. Para isso, foram utlizados vários testes estatísticos. Com base na avaliação efetuada foram identificadas e propostas as seguintes oportunidades de melhoria: - Automação de uma das atividades realizadas no setor Físico-Química I, atividade esta necessária à preparação das análises; - Contrabalançar a sazonalidade verificada na receção de amostras dos clientes com as amostras provenientes da Direção de Serviços de Fiscalização e Controlo; - Inserção de algumas variáveis no software GLAB. É de realçar que a proposta referente à automação de uma das atividades realizadas no setor Físico-Química foi implementada pelo IVDP. Foram, também, identificadas propostas de futuras investigações.

Functional alkali tantalate 2D structures for microelectronics and related applications

Alkali tantalates and niobates, including K(Ta / Nb)O3, Li(Ta / Nb)O3 and Na(Ta / Nb)O3, are a very promising ferroic family of lead-free compounds with perovskite-like structures. Their versatile properties make them potentially interesting for current and future application in microelectronics, photocatalysis, energy and biomedics. Among them potassium tantalate, KTaO3 (KTO), has been raising interest as an alternative for the well-known strontium titanate, SrTiO3 (STO). KTO is a perovskite oxide with a quantum paraelectric behaviour when electrically stimulated and a highly polarizable lattice, giving opportunity to tailor its properties via external or internal stimuli. However problems related with the fabrication of either bulk or 2D nanostructures makes KTO not yet a viable alternative to STO. Within this context and to contribute scientifically to the leverage tantalate based compounds applications, the main goals of this thesis are: i) to produce and characterise thin films of alkali tantalates by chemical solution deposition on rigid Si based substrates, at reduced temperatures to be compatible with Si technology, ii) to fulfil scientific knowledge gaps in these relevant functional materials related to their energetics and ii) to exploit alternative applications for alkali tantalates, as photocatalysis. In what concerns the synthesis attention was given to the understanding of the phase formation in potassium tantalate synthesized via distinct routes, to control the crystallization of desired perovskite structure and to avoid low temperature pyrochlore or K-deficient phases. The phase formation process in alkali tantalates is far from being deeply analysed, as in the case of Pb-containing perovskites, therefore the work was initially focused on the process-phase relationship to identify the driving forces responsible to regulate the synthesis. Comparison of phase formation paths in conventional solid-state reaction and sol-gel method was conducted. The structural analyses revealed that intermediate pyrochlore K2Ta2O6 structure is not formed at any stage of the reaction using conventional solid-state reaction. On the other hand in the solution based processes, as alkoxide-based route, the crystallization of the perovskite occurs through the intermediate pyrochlore phase; at low temperatures pyrochlore is dominant and it is transformed to perovskite at >800 °C. The kinetic analysis carried out by using Johnson-MehlAvrami-Kolmogorow model and quantitative X-ray diffraction (XRD) demonstrated that in sol-gel derived powders the crystallization occurs in two stages: i) at early stage of the reaction dominated by primary nucleation, the mechanism is phase-boundary controlled, and ii) at the second stage the low value of Avrami exponent, n ~ 0.3, does not follow any reported category, thus not permitting an easy identification of the mechanism. Then, in collaboration with Prof. Alexandra Navrotsky group from the University of California at Davis (USA), thermodynamic studies were conducted, using high temperature oxide melt solution calorimetry. The enthalpies of formation of three structures: pyrochlore, perovskite and tetragonal tungsten bronze K6Ta10.8O30 (TTB) were calculated. The enthalpies of formation from corresponding oxides, ∆Hfox, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -203.63 ± 2.84 kJ/mol, - 358.02 ± 3.74 kJ/mol, and -1252.34 ± 10.10 kJ/mol, respectively, whereas from elements, ∆Hfel, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -1408.96 ± 3.73 kJ/mol, -2790.82 ± 6.06 kJ/mol, and -13393.04 ± 31.15 kJ/mol, respectively. The possible decomposition reactions of K-deficient KTa2.2O6 pyrochlore to KTaO3 perovskite and Ta2O5 (reaction 1) or to TTB K6Ta10.8O30 and Ta2O5 (reaction 2) were proposed, and the enthalpies were calculated to be 308.79 ± 4.41 kJ/mol and 895.79 ± 8.64 kJ/mol for reaction 1 and reaction 2, respectively. The reactions are strongly endothermic, indicating that these decompositions are energetically unfavourable, since it is unlikely that any entropy term could override such a large positive enthalpy. The energetic studies prove that pyrochlore is energetically more stable phase than perovskite at low temperature. Thus, the local order of the amorphous precipitates drives the crystallization into the most favourable structure that is the pyrochlore one with similar local organization; the distance between nearest neighbours in the amorphous or short-range ordered phase is very close to that in pyrochlore. Taking into account the stoichiometric deviation in KTO system, the selection of the most appropriate fabrication / deposition technique in thin films technology is a key issue, especially concerning complex ferroelectric oxides. Chemical solution deposition has been widely reported as a processing method to growth KTO thin films, but classical alkoxide route allows to crystallize perovskite phase at temperatures >800 °C, while the temperature endurance of platinized Si wafers is ~700 °C. Therefore, alternative diol-based routes, with distinct potassium carboxylate precursors, was developed aiming to stabilize the precursor solution, to avoid using toxic solvents and to decrease the crystallization temperature of the perovskite phase. Studies on powders revealed that in the case of KTOac (solution based on potassium acetate), a mixture of perovskite and pyrochlore phases is detected at temperature as low as 450 °C, and gradual transformation into monophasic perovskite structure occurs as temperature increases up to 750 °C, however the desired monophasic KTaO3 perovskite phase is not achieved. In the case of KTOacac (solution with potassium acetylacetonate), a broad peak is detected at temperatures <650 °C, characteristic of amorphous structures, while at higher temperatures diffraction lines from pyrochlore and perovskite phases are visible and a monophasic perovskite KTaO3 is formed at >700 °C. Infrared analysis indicated that the differences are due to a strong deformation of the carbonate-based structures upon heating. A series of thin films of alkali tantalates were spin-coated onto Si-based substrates using diol-based routes. Interestingly, monophasic perovskite KTaO3 films deposited using KTOacac solution were obtained at temperature as low as 650 °C; films were annealed in rapid thermal furnace in oxygen atmosphere for 5 min with heating rate 30 °C/sec. Other compositions of the tantalum based system as LiTaO3 (LTO) and NaTaO3 (NTO), were successfully derived as well, onto Si substrates at 650 °C as well. The ferroelectric character of LTO at room temperature was proved. Some of dielectric properties of KTO could not be measured in parallel capacitor configuration due to either substrate-film or filmelectrode interfaces. Thus, further studies have to be conducted to overcome this issue. Application-oriented studies have also been conducted; two case studies: i) photocatalytic activity of alkali tantalates and niobates for decomposition of pollutant, and ii) bioactivity of alkali tantalate ferroelectric films as functional coatings for bone regeneration. Much attention has been recently paid to develop new type of photocatalytic materials, and tantalum and niobium oxide based compositions have demonstrated to be active photocatalysts for water splitting due to high potential of the conduction bands. Thus, various powders of alkali tantalates and niobates families were tested as catalysts for methylene blue degradation. Results showed promising activities for some of the tested compounds, and KNbO3 is the most active among them, reaching over 50 % degradation of the dye after 7 h under UVA exposure. However further modifications of powders can improve the performance. In the context of bone regeneration, it is important to have platforms that with appropriate stimuli can support the attachment and direct the growth, proliferation and differentiation of the cells. In lieu of this here we exploited an alternative strategy for bone implants or repairs, based on charged mediating signals for bone regeneration. This strategy includes coating metallic 316L-type stainless steel (316L-SST) substrates with charged, functionalized via electrical charging or UV-light irradiation, ferroelectric LiTaO3 layers. It was demonstrated that the formation of surface calcium phosphates and protein adsorption is considerably enhanced for 316L-SST functionalized ferroelectric coatings. Our approach can be viewed as a set of guidelines for the development of platforms electrically functionalized that can stimulate tissue regeneration promoting direct integration of the implant in the host tissue by bone ingrowth and, hence contributing ultimately to reduce implant failure.