Investigation of the effects of low energy high dose ion bombardment in metals and compound semiconductors

The effect of low energy nitrogen molecular ion beam bombardment on metals and compound semiconductors has been studied, with the aim to investigate at the effects of ion and target properties. For this purpose, nitrogen ion implantation in aluminium, iron, copper, gold, GaAs and AIGaAs is studied using XPS and Angle Resolve XPS. A series of experimental studies on N+2 bombardment induced compositional changes, especially the amount of nitrogen retained in the target, were accomplished. Both monoenergetic implantation and non-monoenergetic ion implantation were investigated, using the VG Scientific ESCALAB 200D system and a d. c. plasma cell, respectively. When the samples, with the exception of gold, are exposed to air, native oxide layers are formed on the surfaces. In the case of monoenergetic implantation, the surfaces were cleaned using Ar+ beam bombardment prior to implantation. The materials were then bombarded with N2+ beam and eight sets of successful experiments were performed on each sample, using a rastered N2+ ion beam of energy of 2, 3, 4 and 5 keV with current densities of 1 μA/cm2 and 5 μA/cm22 for each energy. The bombarded samples were examined by ARXPS. After each complete implantation, XPS depth profiles were created using Ar+ beam at energy 2 ke V and current density 2 μA/cm2 . As the current density was chosen as one of the parameters, accurate determination of current density was very important. In the case of glow discharge, two sets of successful experiments were performed in each case, by exposing the samples to nitrogen plasma for the two conditions: at low pressure and high voltage and high pressure and low voltage. These samples were then examined by ARXPS. On the theoretical side, the major problem was prediction of the number of ions of an element that can be implanted in a given matrix. Although the programme is essentially on experimental study, but an attempt is being made to understand the current theoretical models, such as SATVAL, SUSPRE and TRIM. The experimental results were compared with theoretical predictions, in order to gain a better understanding of the mechanisms responsible. From the experimental results, considering possible experimental uncertainties, there is no evidence of significant variation in nitrogen saturation concentration with ion energy or ion current density in the range of 2-5 ke V, however, the retention characteristics of implantant seem to strongly depend on the chemical reactivity between ion species and target material. The experimental data suggests the presence of at least one thermal process. The discrepancy between the theoretical and experimental results could be the inability of the codes to account for molecular ion impact and thermal processes.

Migration of additives from thermoplastic polymers

A homologous series of ultra-violet stabilisers containing 2-hydroxybenzophenone (HBP) moiety as a uv absorbing chromophore with varying alkyl chain lengths and sizes were prepared by known chemical synthesis. The strong absorbance of the HBP chromophore was utilized to evaluate the concentration of these stabilisers in low density polyethylene films and concentration of these stabilisers in low density polyethylene films and in relevant solvents by ultra-violet/visible spectroscopy. Intrinsic diffusion coefficients, equilibrium solubilities, volatilities from LDPE films and volatility of pure stabilisers were studied over a temperature range of 5-100oC. The effects of structure, molecular weight and temperature on the above parameters were investigated and the results were analysed on the basis of theoretical models published in the literature. It has been found that an increase in alkyl chain lengths does not change the diffusion coefficients to a significant level, while attachment of polar or branched alkyl groups change their value considerably. An Arrhenius type of relationship for the temperature dependence of diffusion coefficients seems to be valid only for a narrow temperature range, and therefore extrapolation of data from one temperature to another leads to a considerable error. The evidence showed that increase in additive solubility in the polymer is favoured by lower heat of fusions and melting points of additives. This implies the validity of simple regular solution theory to provide an adequate basis for understanding the solubility of additives in polymers The volubility of stabilisers from low density polyethylene films showed that of an additive from a polymer can be expressed in terms of a first-order kinetic equation. In addition the rate of loss of stabilisers was discussed in relation to its diffusion, solubility and volatility and found that all these factors may contribute to the additive loss, although one may be a rate determining factor. Stabiliser migration from LDPE into various solvents and food simulants was studied at temperatures 5, 23, 40 and 70oC; from the plots of rate of migration versus square root time, characteristic diffusion coefficients were obtained by using the solution of Fick's diffusion equations. It was shown that the rate of migration depends primarily on partition coefficients between solvent and the polymer of the additive and also on the swelling action of the contracting media. Characteristic diffusion coefficients were found to approach to intrinsic values in non swelling solvents, whereas in the case of highly swollen polymer samples, the former may be orders of magnitude greater than the latter.

Differences in market-oriented behaviour levels across firms' domestic and export marketing operations:a study of antecedents and consequences

Researchers are beginning to recognise that organisations often have different levels of market orientation across different aspects of their operations. Focusing on firms involved in export marketing, this study examines how market-oriented behaviour differs across firms' domestic and export marketing operations. In this respect, the study is the first of its kind since it investigates three main issues: (1) to what extent do differences exist in firms' levels of market-oriented behaviour in their domestic markets (i.e., their domestic market-oriented behaviour) and in their export markets (i.e., their export market-oriented behaviour), (2) what are the key drivers of such differences, and (3) what are the performance implications for firms of having different levels of domestic and export market-oriented behaviour. To shed light on these research questions, data were collected from 225 British exporting firms using a mail questionnaire. Structural equation modelling techniques were used to develop and purify measures of all construct of interest, and to test the theoretical models developed. The results indicate that many of businesses sampled have very different levels of market orientation in their domestic and exporting operations: typically, firms tend to be more market-oriented in their domestic markets relative to their export markets. Several key factors were identified as drivers of differences in market orientation levels across firms' domestic and export markets. In particular, it was found that differences were more pronounced when: (i) interfunctional interactions between domestic marketing and export marketing are rare, (ii) when domestic and export marketing follow asymmetric business strategies, (iii) when mutual dependence between the functions is low, (iv) when one or other of the functions dominates the firm's sales, and (v) when there are pronounced differences in the degree to which the domestic and the export markets are experiencing environmental turbulence. The consequences of differences in market-oriented behaviour across firms' domestic and export markets were also studied. The results indicate that overall sales performance of firms (as determined by the composite of firms' domestic sales and export sales performance) is positively related to levels of domestic market-oriented behaviour under high levels of environmental turbulence in firms' domestic markets. However, as domestic market turbulence decreases, so to does the strength of this positive relationship. On the other hand, export market-oriented behaviour provides a positive contribution to firms' overall sales success under conditions of relatively low export market turbulence. As the turbulence in export markets increases, this positive relationship becomes weaker. These findings indicate that there are numerous situations in which it is sub-optimal for firms to have identical levels of market-oriented behaviour in their domestic and exporting operations. The theoretical and practical implications of these findings are discussed.

System identification of linear vibrating structures

Methods of dynamic modelling and analysis of structures, for example the finite element method, are well developed. However, it is generally agreed that accurate modelling of complex structures is difficult and for critical applications it is necessary to validate or update the theoretical models using data measured from actual structures. The techniques of identifying the parameters of linear dynamic models using Vibration test data have attracted considerable interest recently. However, no method has received a general acceptance due to a number of difficulties. These difficulties are mainly due to (i) Incomplete number of Vibration modes that can be excited and measured, (ii) Incomplete number of coordinates that can be measured, (iii) Inaccuracy in the experimental data (iv) Inaccuracy in the model structure. This thesis reports on a new approach to update the parameters of a finite element model as well as a lumped parameter model with a diagonal mass matrix. The structure and its theoretical model are equally perturbed by adding mass or stiffness and the incomplete number of eigen-data is measured. The parameters are then identified by an iterative updating of the initial estimates, by sensitivity analysis, using eigenvalues or both eigenvalues and eigenvectors of the structure before and after perturbation. It is shown that with a suitable choice of the perturbing coordinates exact parameters can be identified if the data and the model structure are exact. The theoretical basis of the technique is presented. To cope with measurement errors and possible inaccuracies in the model structure, a well known Bayesian approach is used to minimize the least squares difference between the updated and the initial parameters. The eigen-data of the structure with added mass or stiffness is also determined using the frequency response data of the unmodified structure by a structural modification technique. Thus, mass or stiffness do not have to be added physically. The mass-stiffness addition technique is demonstrated by simulation examples and Laboratory experiments on beams and an H-frame.

Varieties of acquired phonological dyslexia

The existence of different varieties of the acquired reading disorder termed "phonological dyslexia" is demonstrated in this thesis. The data are interpreted in terms of an information-processing model of normal reading which postulates autonomous routes for pronouncing lexical and non-lexical items and identifies a number of separable sub-processes within both lexical and non-lexical routes. A case study approach is used and case reports on ten patients who have particular difficulty in processing non-lexical stimuli following cerebral insult are presented, Chapters 1 and 2 describe the theoretical background to the investigation. Cognitive models of reading are examined in Chapter 1 and the theoretical status of the current taxonomy of the acquired dyslexias discussed in relation to the models. In Chapter 2 the symptoms associated with phonological dyslexia are discussed both in terms of the theoretical models and in terms of the cosistency with which they are reported to occur in clinical studies. Published cases of phonological dyslexia are reviewed. Chapter 3 describes the tests administered and the analysis of error responses. The majority of tests require reading aloud of single lexical or non-lexical items and investigate the effect of different variables on reading performance. Chapter 4 contains the case reports. The final chapter summarises the different patterns of reading behaviour observed. The theoretical model predicts the selective impairment of subsystems within the phonological route. The data provide evidence of such selective impairment. It is concluded that there are different varieties of phonological dyslexia corresponding to the different loci of impairment within the phonological route. It is also concluded that the data support the hypothesis that there are two lexical routes. A further subdivision of phonological dyslexia is made on the basis of selective impairment of the direct or lexical-semantic routes.

Synchronization processes in nonlinear systems and their relation to cortical oscillatory dynamics

This thesis was focused on theoretical models of synchronization to cortical dynamics as measured by magnetoencephalography (MEG). Dynamical systems theory was used in both identifying relevant variables for brain coordination and also in devising methods for their quantification. We presented a method for studying interactions of linear and chaotic neuronal sources using MEG beamforming techniques. We showed that such sources can be accurately reconstructed in terms of their location, temporal dynamics and possible interactions. Synchronization in low-dimensional nonlinear systems was studied to explore specific correlates of functional integration and segregation. In the case of interacting dissimilar systems, relevant coordination phenomena involved generalized and phase synchronization, which were often intermittent. Spatially-extended systems were then studied. For locally-coupled dissimilar systems, as in the case of cortical columns, clustering behaviour occurred. Synchronized clusters emerged at different frequencies and their boundaries were marked through oscillation death. The macroscopic mean field revealed sharp spectral peaks at the frequencies of the clusters and broader spectral drops at their boundaries. These results question existing models of Event Related Synchronization and Desynchronization. We re-examined the concept of the steady-state evoked response following an AM stimulus. We showed that very little variability in the AM following response could be accounted by system noise. We presented a methodology for detecting local and global nonlinear interactions from MEG data in order to account for residual variability. We found crosshemispheric nonlinear interactions of ongoing cortical rhythms concurrent with the stimulus and interactions of these rhythms with the following AM responses. Finally, we hypothesized that holistic spatial stimuli would be accompanied by the emergence of clusters in primary visual cortex resulting in frequency-specific MEG oscillations. Indeed, we found different frequency distributions in induced gamma oscillations for different spatial stimuli, which was suggestive of temporal coding of these spatial stimuli. Further, we addressed the bursting character of these oscillations, which was suggestive of intermittent nonlinear dynamics. However, we did not observe the characteristic-3/2 power-law scaling in the distribution of interburst intervals. Further, this distribution was only seldom significantly different to the one obtained in surrogate data, where nonlinear structure was destroyed. In conclusion, the work presented in this thesis suggests that advances in dynamical systems theory in conjunction with developments in magnetoencephalography may facilitate a mapping between levels of description int he brain. this may potentially represent a major advancement in neuroscience.

A cross-cultural study of factors influencing helping behaviour

The burgeoning research into altruism and helping behaviour has examined the effect of many variables that enhance or inhibit helpfulness, but little attention has been given to the influence of culture. In the present research, data on various aspects of helping behaviour were collected in both the UK and the Sudan so that the importance of cultural influences could be investigated. In addition this research also tested the validity of current models of helping. In a repertory grid study, urgency and cost emerged as the main constructs people in the two countries use to distinguish between various helpful situations. A laboratory experiment designed to test existing models of intervention behaviour found significant main effects of country, group, size, cost and urgency; and a group size/urgency interaction. Subjects in the Sudan intervened faster than subjects in the UK; lone subjects intervened faster than subjects in small and large groups; subjects in low cost intervened faster than subjects in high cost conditions; and subjects in high urgency intervened faster than subjects in low urgency conditions. Group size effect was stronger in low than in high urgency conditions. Two field studies further investigated the effect of urgency and cost in urban-nonurban context. Significant main effects of urgency and cost were found in cities but not in towns; and people in cities were less helpful than people in towns. A questionnaire survey found that in both countries there were significant urban-nonurban differences in the incidence of reported social contacts and exchange of helpful acts between acquaintances, neighbours and strangers. However, there were no urban-nonurban differences between relatives and close friends. Finally, attitudes to altruism and helpfulness did not differ between the two countries or between urban and nonurban residents. The results highlight the need to incorporate urgency and cultural variables in theoretical models of helping behaviour.

Some aspects of the dynamic performance of machine tool structural joints

The work presented in this thesis is concerned with the dynamic behaviour of structural joints which are both loaded, and excited, normal to the joint interface. Since the forces on joints are transmitted through their interface, the surface texture of joints was carefully examined. A computerised surface measuring system was developed and computer programs were written. Surface flatness was functionally defined, measured and quantised into a form suitable for the theoretical calculation of the joint stiffness. Dynamic stiffness and damping were measured at various preloads for a range of joints with different surface textures. Dry clean and lubricated joints were tested and the results indicated an increase in damping for the lubricated joints of between 30 to 100 times. A theoretical model for the computation of the stiffness of dry clean joints was built. The model is based on the theory that the elastic recovery of joints is due to the recovery of the material behind the loaded asperities. It takes into account, in a quantitative manner, the flatness deviations present on the surfaces of the joint. The theoretical results were found to be in good agreement with those measured experimentally. It was also found that theoretical assessment of the joint stiffness could be carried out using a different model based on the recovery of loaded asperities into a spherical form. Stepwise procedures are given in order to design a joint having a particular stiffness. A theoretical model for the loss factor of dry clean joints was built. The theoretical results are in reasonable agreement with those experimentally measured. The theoretical models for the stiffness and loss factor were employed to evaluate the second natural frequency of the test rig. The results are in good agreement with the experimentally measured natural frequencies.

Fatigue crack initiation and propagation from defects in aluminium welds

Fatigue crack initiation and propagation in aluminium butt welds has been investigated. It is shown that the initiation of cracks from both buried defects and. from the weld reinforcement may be quantified by predictive laws based on either linear elastic fracture mechanics, or on Neuber's rule of stress and strain ooncentrations. The former is preferable on the grounds of theoretical models of crack tip plasticity, although either may be used as the basis of an effeotive design criteria against crack initiation. Fatigue lives fol1owing initiation were found to follow predictions based on the integration of a Paris type power law. The effect of residual stresses from the welding operation on both initiation and propagation was accounted for by a Forman type equation. This incorporated the notional stress ratio produced by the residual stresses after various heat treatments. A fracture mechanics analysis was found to be useful in describing the fatigue behaviour of the weldments at increased temperatures up to 300°C. It is pointed out, however, that the complex interaction of residual stresses, frequency, and changes in fracture mode necessitate great caution in the application of any general design criteria against crack initiation and growth at elevated. temperatures.

Comparing German and British political culture through values : and analysis of the values of health care reform

This research sets out to compare the values in British and German political discourse, especially the discourse of social policy, and to analyse their relationship to political culture through an analysis of the values of health care reform. The work proceeds from the hypothesis that the known differences in political culture between the two countries will be reflected in the values of political discourse, and takes a comparison of two major recent legislative debates on health care reform as a case study. The starting point in the first chapter is a brief comparative survey of the post-war political cultures of the two countries, including a brief account of the historical background to their development and an overview of explanatory theoretical models. From this are developed the expected contrasts in values in accordance with the hypothesis. The second chapter explains the basis for selecting the corpus texts and the contextual information which needs to be recorded to make a comparative analysis, including the context and content of the reform proposals which comprise the case study. It examines any contextual factors which may need to be taken into account in the analysis. The third and fourth chapters explain the analytical method, which is centred on the use of definition-based taxonomies of value items and value appeal methods to identify, on a sentence-by-sentence basis, the value items in the corpus texts and the methods used to make appeals to those value items. The third chapter is concerned with the classification and analysis of values, the fourth with the classification and analysis of value appeal methods. The fifth chapter will present and explain the results of the analysis, and the sixth will summarize the conclusions and make suggestions for further research.

The role of experts in policy making

As public policy issues increasingly have a technical aspect to them an interactive relationship has developed between science and policy. The aim of this thesis is to investigate the two aspects of this relationship: the influence of science on policy and the influence of policy implications on science. Most existing studies in this area treat only one or other of these aspects. Furthermore, they tend to provide interesting case study material but very little theoretical analysis. This thesis attempts to overcome these problems by dealing with both aspects of the interaction between science and policy and by providing theoretical models of this relationship. The thesis combines the theoretical development of these models with the analysis of three empirical case studies: the controversy in Britain over smoking and health; the application of educational psychology to the development of education policy in Britain; the controversy over the health effect of lead in the environment. The theoretical models are developed in Part 1. In Part 2 the empirical case studies are presented and in Part 3 the theoretical material is assessed in the light of these case studies. The main thesis of this study is that there is a fundamental mismatch between science and policy-making. Criticism is always essential in science. However, when science is involved in the policy process, either scientific claims are not subjected to a significant level of criticism or they are scrutinized so closely that no view achieves general consensus and conflicting advice results. In this situation, contrary to the traditional view, science can generate uncertainty. The role which science plays in the policy process is influenced by this level of criticism, by the context of political power and by the progress of an issue through the various stages of the policy process.

Properties of seawater bitterns with regard to liquid-desiccant cooling

This study concerns the properties of the concentrated bittern solutions occurring as by-product from solar salt works, in relation to their potential use as liquid desiccants in cooling systems. Solutions of compositions similar to those of bitterns have been made up in the laboratory, as have concentrated mixtures of MgCl2–MgSO4–H2O. Measurements of vapour pressure have been carried out using an isoteniscope and are reported together with measurements of density and viscosity. Several theoretical models representing these properties are reviewed and compared against the experimental results; the average agreement between theory and experiment is within 5% for vapour pressure and better for the preferred models of the other two properties. Based on these findings, an expression is provided for the equilibrium relative humidity of bitterns as a function of concentration relative to raw seawater. The vapour pressures of bittern solutions are found to be similar to those of solutions containing only magnesium chloride but having the same mass fraction of total salts. Therefore magnesium chloride solution is a reasonable model for bitterns for the purpose of developing the proposed cooling system.

Disconnected brains:what is the role of fMRI in connectivity research?

In this paper we consider how functional Magnetic Resonance Imaging (fMRI) has been used to study cortical connectivity in autism and autistic spectrum disorders (ASD). We discuss those studies that have contributed to the evidence supporting a model of disordered cortical connectivity in autism and (ASD), with a focusing emphasis on the application to research into the underconnectivity model. We note that the analytical techniques employed are limited and do not allow interpretation in terms of effective, or directional connectivity, nor do they provide information about the temporal or spectral characteristics of the functional networks being studied. We highlight how currently the features of neural generators that are being assessed by functional connectivity in fMRI are unclear. In addition, we note the importance in clinical studies of considering the consequences of task choice for the nature of the imaging data that can be collected and also of individual differences in participant state and trait characteristics for the accurate interpretation of imaging data. We discuss how alternative techniques such as EEG/MEG may address the limitations of fMRI in assessing brain connectivity, and additionally consider the potential of multimodal approaches. We conclude that fMRI has made significant contributions towards our understanding of the brain in terms of neural systems but that the conclusions drawn from its application in the sphere of autism research need to be approached with caution. It is important in research of this kind that we are aware of the need to examine the methodological and analytical techniques closely when applying findings in clinical populations, not only when they are used to support the development of theoretical models but also to inform diagnostic or treatment decisions.

In situ imaging and height reconstruction of phase separation processes in polymer blends during spin coating

Spin coating polymer blend thin films provides a method to produce multiphase functional layers of high uniformity covering large surface areas. Applications for such layers include photovoltaics and light-emitting diodes where performance relies upon the nanoscale phase separation morphology of the spun film. Furthermore, at micrometer scales, phase separation provides a route to produce self-organized structures for templating applications. Understanding the factors that determine the final phase-separated morphology in these systems is consequently an important goal. However, it has to date proved problematic to fully test theoretical models for phase separation during spin coating, due to the high spin speeds, which has limited the spatial resolution of experimental data obtained during the coating process. Without this fundamental understanding, production of optimized micro- and nanoscale structures is hampered. Here, we have employed synchronized stroboscopic illumination together with the high light gathering sensitivity of an electron-multiplying charge-coupled device camera to optically observe structure evolution in such blends during spin coating. Furthermore the use of monochromatic illumination has allowed interference reconstruction of three-dimensional topographies of the spin-coated film as it dries and phase separates with nanometer precision. We have used this new method to directly observe the phase separation process during spinning for a polymer blend (PS-PI) for the first time, providing new insights into the spin-coating process and opening up a route to understand and control phase separation structures. © 2011 American Chemical Society.

Modelling and experimental verification of a solar-powered liquid desiccant cooling system for greenhouse food production in hot climates

Experiments and theoretical modelling have been carried out to predict the performance of a solar-powered liquid desiccant cooling system for greenhouses. We have tested two components of the system in the laboratory using MgCl2 desiccant: (i) a regenerator which was tested under a solar simulator and (ii) a desiccator which was installed in a test duct. Theoretical models have been developed for both regenerator and desiccator and gave good agreement with the experiments. The verified computer model is used to predict the performance of the whole system during the hot summer months in Mumbai, Chittagong, Muscat, Messina and Havana. Taking examples of temperate, sub-tropical, tropical and heat-tolerant tropical crops (lettuce, soya bean, tomato and cucumber respectively) we estimate the extensions in growing seasons enabled by the system. Compared to conventional evaporative cooling, the desiccant system lowers average daily maximum temperatures in the hot season by 5.5-7.5 °C, sufficient to maintain viable growing conditions for lettuce throughout the year. In the case of tomato, cucumber and soya bean the system enables optimal cultivation through most summer months. It is concluded that the concept is technically viable and deserves testing by means of a pilot installation at an appropriate location.